Tender For Provision Of Additional Toilet In Bldg No P-163 Storage Facility In Bldg No P-222 P-244 P-163 P-165 P-92 And Addn Altn To Existing Toilets Of Bldg No P-48 Into Ladies Toilets For Agv Trainees
Tender Value
Ref. Documents
Estimated cost
Bid Submission
04 Sep 2025
0 days left
EMD
1 Lakhs
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
jalahalli → Karnataka
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Provision Of Additional Toilet In Bldg No P-163 Storage Facility In Bldg No P-222 P-244 P-163 P-165 P-92 And Addn Altn To Existing Toilets Of Bldg No P-48 Into Ladies Toilets For Agv Trainees
BOQ
| Sl. No. | Item Description |
| 1 | Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5 m deep for foundation etc., and getting out in soft/loose soil complete all as specified anddirected. |
| 2 | M&LPCC 1:4:8 type D-2 (using 40mm graded agg) in foundation, filling and mass concrete complete all as specified and as directed. |
| 3 | M&L Hard core of gauge n.exe.63mm with broken stone boulders, deposited spread and levelled in layers not exe 15 cm thick watered and rolled rammed to a true surfaces complete all as specified and as directed. |
| 4 | M&L pre-cast PCC 1:3:6 type C1 (20 mm graded agg) cement concrete block masonry with solid blocks exc. 10cm in width and set in cement mortar 1:6 complete all as specified and as directed. |
| 5 | M&L RCC type B1 1:2:4, 20 mm graded stone aggregate (nominal mix)as in plinth beam/band etc mixed withintegral water proofing compound.(WPC shall be measured separately)complete all as specified and as directed. |
| 6 | Supply only integral liquid water proofing compound of approved make complete all as specified and as directed. |
| 7 | M&L TMT bar10mm dia& over deformed & twisted bars cut to length ,bent to shape required incl cranking , bending , hooking, for lintel and binding with MS wire not less than 0.9 mm dia or securing with clips complete all as specified and as directed. |
| 8 | M&L for TMT bars 5mm dia and over upto 10mm dia as in stirups cut to length bent to shape required including cranking, hooking ends etc and binding with MS wire not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 9 | Formwork to sides of concrete foundation,footing,base of columns,raft and raft beam,sides and soffits (if any) of foundation and plinth beams,and similar works,vertical or to batter rough finished flate surface of concrete complete all as specified and as directed. |
| 10 | M & L for 100 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base, surfaces finished even and fairetc complete all as specified and directed . |
| 11 | M&L for MS Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates as reqd forming holes bolted and welded attchment and curved shaped by welding (thickness of metal n.exc.6mm) making jointless by filling including cutting of Fe 410-B complete all as specified and as directed. |
| 12 | S&F galvalume sheets AZ-150 having pitch 190mm, depth 29mm and thickness not less than 0.50mm (Galvalume base- trapezoidal profile sheets) fixed with aluminium self tapPing screws and aluminium washer of suitable size in roof covering, gutters and cladding all as specified. (Over lap shall be as specified by manufacturer) |
| 13 | S&F for galvalume sheets AZ-150 plain sheets havung thickness not less than 0.50mm (Galvalume base- trapezoidal profile sheets) fixed with aluminium self tapPing screws and aluminium washer of suitable size in roof covering, gutters and cladding all as specified. (Over lap shall be as specified by manufacturer) |
| 14 | M&L for preparation of new steel surface and applying two coats of synthetic enamel paint on new steel surface over a coat of red oxide primer complete all as specified and as directed. |
| 15 | Returning filling in, including spreading, leveling,watering and well ramming in layers n exc 25cm complete all as specified and as directed. |
| 16 | Filling under floor in layers not exc 25 cm incl spreading, levelling watering etc complete using soils from excavation complete all as specified and as directed. |
| 17 | Removing excavated material nexceeding 250m and depositing where directed at a level not exceeding 1.5m above the ground level the starting point all as specified and directed. |
| 18 | M&L 15mm thick rendering on externalfair faces of brick work or concrete surfaces in CM 1:4mixed with water proofing compound and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.Note : WPC shall be measured & paid seperately. |
| 19 | M&L preparation of plastered surfaces of walls and applying two coats of cement base paint over primer alkali resistance on new surfaces complete all as specified and as directed. |
| 20 | M&L for 15 mm thick screed bed in cement mortar 1:4 for layingfloor finishes under floor complete all as specified and as directed. |
| 21 | M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed. |
| 22 | M&L for rendering 10mm thick in CM 1:3 on fair faces of brick work or concrete surfaces as in backing coat to receive wall tiles etc complete all as specified and directed |
| 23 | M & L for coloured glazed ceramic tiles of size 300x600 x 7 to 8 mm thick jointless tiles on vertical surfaces such as skirting, dados etc, set and jointed in neat cement slurry and pointed in colouredcement to match complete all as specified and as directed. |
| 24 | Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in hard dense soil complete all as specified and as directed. |
| 25 | Material and labourfor 75mm thick cement concrete1:3:6 type C-2 (using 40 mm graded crushedstone aggregate ) as in plinth protection and finished even and smooth without using extra cement complete all as specified and as directed. |
| 26 | M&L for Anodised aluminium Ventilators shutters, including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified |
| 27 | S &F 3mm thick frosted glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed. |
| 28 | S&F of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing all as per drawing complete all as specified and as directed. |
| 29 | S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing directed by Engr-in-Charge. |
| 30 | S & F 150 mm Aluminium, anodised, barrel tower bolts of extruded section and fixedcomplete all as specified and as directed. |
| 31 | Supply & Fixing150 mm Aluminium handles, cast type, anodisedcomplete all as specified and as directed. |
| 32 | S&FButt hinges, medium weight coldrolled mild steel and fixed 75mm size complete all as specified and as directed. |
| 33 | S & F 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete all as specified and as directed. |
| 34 | M&L for annodised aluminium snap grid frame work for false ceiling incl hangers of suitable size GI wire (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 3 mm dia 40mm long and 6.5 mm thick Exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mmx600mm grid complete all as specified and as directed. |
| 35 | S&F vitreous china wash down water closet (pedestal pattern) EWC white incl plastic water closet seat cover and mild steel chromium plated on aluminium hinging device and connecting to \"P\" or \"S\" trap incl connecting flush pipe with flushing rim complete all as specified and as directed. |
| 36 | S&F vitreous china wash basin white flat back size 550x400mm including brackets, waste coupling full or half threaded 32mm dia (min wt 45gms) complete all as specified and as directed. |
| 37 | S&F vitreous china urinal bowlof flat back, size of 465x355x265mm, white with grating & unions for discharge pipe complete including provide and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in fixing automatic flushing cistern with brackets, flush pipe, grating and unions for discharge pipe and complete all as specified and as directed. |
| 38 | S&F PVC valveless 10 litres capacity,syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes complete all as specified and as directed. |
| 39 | S&F of CP 1.5m pipe health faucet cat part No (ALD-CHR-563) of Jaquar or equivalentall as specified and as directed. |
| 40 | Supply and fix 15 mm borefancy type single lever Basin pillar tap chromium plated cast copper alloy with capstan head, long screwed shanks cat part No (OPP-CHR-15001PM) of Jaquar or equivelentall as specified and as directed. |
| 41 | S&F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. |
| 42 | S& F of 15mm dia concussive push button taps of cast copper alloy, chromium plated screwed for iron pipe and fixed |
| 43 | S&F Urinal spreader of PTMT any colour for fixing with 15mm dia pipe (minimum wt 60 gms) |
| 44 | S & F75 mm bore PVC (SWR) floor trapwith grating incl jointing with solvent cement complete all as specified and as directed. |
| 45 | M&L for Granite slab 18 to 20mm thick (table rubbed and polished) in partition, set in cement mortar (1:4) complete all as specified and as directed. |
| 46 | S & F Rotational moulded Polyethylene water storage tank - 2000 liters capacity (cylidrical vertical , threaded top cover) hoisted and fixed in position all as specified in SSR part I complete all as specified and as directed. |
| 47 | M&L for 25mm boreCPVCtubes including fittings concealed in walls complete all as specified and as directed. |
| 48 | S & F 25 mm dia CPVC gate valve screwed both ends for CPVC pipe complete all as specified and as directed. |
| 49 | M&L for Bib taps cast copper alloy fancy type chromium plated 15mm bore fixed complete all as specified and as directed. |
| 50 | S&FCP soap disk 100 mm x 100mmfixed with screw to wall complete all as specified and as directed. |
| 51 | S & F chromium plated towel rail 20mm dia D type 60 cm longcomplete all as specified and as directed. |
| 52 | S&F angular stop valves cast copper screwed down high pressure fancy type screwed both ends for pipe or union fixed for 15mm bore complete all as specified and as directed. |
| 53 | S& F 15mm bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified anddirected. |
| 54 | S & F PVC connection 15 mm bore, 450 mm long complete with both ends unions complete all as specified and as directed. |
| 55 | Supply and fix 110mm dia PVC (SWR) pipe single socket in any length with rubber ring joint fixed to wall or laid in trenches complete all as specified and as directed. |
| 56 | Supply and fix 75mm dia PVC (SWR) pipe single socket in any length with rubber ring joint fixed to wall or laid in trenches complete all as specified and as directed. |
| 57 | Supply and fixPVC cowl 110 mm dia complete all as specified and as directed. |
| 58 | Supply and fix 110mm dia PVC bend any radius complete all as specified and as directed. |
| 59 | All as per item 58above but 75mm dia complete all as specified and as directed. |
| 60 | S & F PVC (SWR) bends of any radius with access door bore of pipe 75 mm complete all as specified and as directed. |
| 61 | All as per item No.60 above but bore of pipe 110 mm with access door complete all as specified and as directed. |
| 62 | S & F PVC (SWR)junction single(single T)equal or unequal with access door bore of pipe 110 mm complete all as specified and as directed. |
| 63 | S & F Rotational moulded Polyethylene water storage tank - 1000 liters capacity (cylidrical vertical , threaded top cover) hoisted and fixed in position all as specified in SSR part I complete all as specified and as directed. |
| 64 | M&L for 20mm bore CPVC tubes including fittings concealed in walls complete all as specified and as directed. |
| 65 | S & F 20 mm dia CPVC gate valve screwed both ends for CPVC pipecomplete all as specified and as directed. |
| 66 | M & L for Sand filling under floors or in foundations including watering and consolidation and all as specified and directed. |
| 67 | M&L for machine pressed pre polished precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 Grade over sand cushion with grey cement and no pigment and complete all as specified and directed |
| 68 | M&L for kerb stone precast with PCC (1:2:4) type B1 using 20mm graded aggregate finished even and fair without using extra cement and all as specified and directed. |
| 69 | S&F waste coupling 32mm dia of PTMT (half or full thread) minimum weight 45 gram complete all as specified and as directed. |
| 70 | M & L salt glazed stone ware drain pipes of internal dia 200 mm bore grade \"A\" laid in trenches and jointed incl demolition and breaking up old drain pipe (salt glazed stoneware drain pipe) set in cement concrete,set in cement mortar all as specified and as directed. |
| 71 | M&L for concrete bed to drain pipe including packing under and haunching against the side of drain pipe after laid and tested in PCC 1:3:6 type C-2 for 200mm diacomplete all as specified and as directed. |
| 72 | M&L for Plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in Foundation/copings/benching of manholes including weathering rounded/chamfered angles and throating as directed including necessary form work. Exposed surfaces of concrete shall be finished even and smooth with out using extra cement complete all as specified and as directed. |
| 73 | Cutting into existing manholes for connecting new drains, making good to pipes and rendering ,cutting out existing benching andforming branch channel, halfround or 3/4 section in cementconcrete1:2:4 type B smooth finished andreformingbenchingas required, internaldia of pipe150mm complete all as specified and as directed. |
| 74 | M & L for Pre-cast reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate set in cement mortar 1:4 as in cover slab including all necessary form work complete all as specified and as directed. |
| 75 | Surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting in soft /loose soil complete all as specified and as directed. |
| 76 | Demolition of cement concrete in ground floors and pavings n.exc 15 cm thick above or below ground level complete all as specified and as directed. |
| 77 | M&L for taking down of existing sunken slab treatment from the sunken portion and removing of existing filling of sunken, cleaning the surfaces washing down with water and rubbish off the primises, cleaning and filling cracks with sealing compound, brushing neat cement [email protected]/sqm and providing 25mm thick cement concrete type B-0 (1:2:4) (using 12.5mm graded stone aggregate) on sunken slab portion.. (b) M&L for two coat of acrylic cementitious water proofing coating (Dr FIXIT pidfin 2K manufactured by M/S Pidilite industries Ltd or equivalent) and followed by a overlay protective rendering15mm thick in CM 1:3 mixed with liquid water proofing compound of approved make and including filling of brick bats and finishing the top surfaces even and smooth without using extra cement .(c)sunken slab after prepration as mentioned above method of application for acrylic cementitious water proofing coating is followed as per manufacturs instruction incl removal of debris material from site complete all as specified and directed. Note: Water proofing compound shall be measured and paid seperately. |
| 78 | Removing existing uncervicable tar felt of any type and any description from roof slab alongwith screed bed, cleaning of surface & removing the debris out side MD land complete all as specified and as directed |
| 79 | Roughening surfaces of old concrete floors by picking, sweeping clean and washing down with water to remove dusts etc. complete all as specified and directed. |
| 80 | M&L for Brushing neat cement slurry with 3kg/sqm all as specified and directed. |
| 81 | M&L PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in concrete padding laid to required slope incl finishing the concrete surface fair and even without using extra cement complete all as specified and as directed. |
| 82 | M & L for 10 mm thick screed bed or bedding layer of mortar in cement mortar (1:4) for laying roof finish as padding finished with WPC as per manufacturers instructions, complete all as specified and directed NOTE :-Integral WPC shall be measured and paid separately. |
| 83 | Apply oil bound bitumen primer @ 0.40 Litre / Sqm manufactured by the same agency as that of APP with density of 0.87 to 0.89 Kg / Litre at 25 degree Celsius on the prepared dry roof surface complete all as specified and directed. |
| 84 | M&L APP polymeric membrane min weighting 3.5kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric(wt not less than 150 gms/sqm laid on primed surfaces by torch application method all as specified and directed. |
| 85 | M&L for preparation of new surfaces of any description not otherwise described over 10cm width or girth and applying one coat of solar reflective aluminium paint @ 0.10 kg/sqm membrane surfaces complete all as specified and directed. |
| 86 | M&L for Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry (1:3) complete all as specified and as directed. |
| 87 | M&L for 40 mm thick PCC 1:2:4 type B-1 using20mm graded stone aggregate as in flooring ,finished cement concrete surface even and smooth using extra cement complete all as specified and as directed. |
| 88 | M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm screed bed 1:4 incl dismantling any floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises complete all as specified and as directed. |
| 89 | M&L coloured Glazed ceramic tiles in vertical surface450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm back coat of CM 1:4 incl dismantling any floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed. |
| 90 | Taking down cement plaster from old walls/ceilingand raking out joints, hacking for key,scrubbing down with water complete all as specified and directed. |
| 91 | Rendering 5mm thick in CM (1:3) on ceiling on fair faces of brick work or concrete surfaces & finished even and smooth without using extra cement complete all as specified and directed. |
| 92 | M&L for rendering15 mm thick in CM 1:4 in two layer each layer 10 mm thickon fair faces of brick work or concrete surfaces and 5mm thick CM (1:4) finished fair and even using integral water proofing compound all as per manufactures instruction and all as specified and as directed.Note: Water proofing compound shall be measured and paid seperately. |
| 93 | Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. but excluding washer facing dressed stone work and precast concrete articles complete all as specified and as directed. |
| 94 | M&L for Raking out joints/ pointing with cement or cement lime mortar to random rubble or polygonal rubble uncoursed or brought up to courses complete all as specified and as directed. |
| 95 | M&L for Raised pointing with CM 1:4 to random or polygonal rubble, uncoursed or brought upto courses complete all as specified and as directed. |
| 96 | M&L for rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished evenand smooth without using extra cement all as specified and as directed. |
| 97 | Supply and fixing powder coated aluminium frame workforpartition with one or more rebates including joining cleats, hooks, hangers, beadings, tower bolts, hinges, rubber gaskets etc,minimum thickness of powder coating 50 microncomplete allas specified and as directed. |
| 98 | Supply and fixing powder coated anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and as directed. |
| 99 | Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. |
| 100 | S & F butt hinges 100 mm long medium weight, cold rolled mild steel completeall as specified and as directed |
| 101 | S&Fetxtrutedaluminium alloy handles,fabricated type anodised150mm long complete all as specified and as directed. |
| 102 | S&F aluminium anodised, barrel tower bolts of extruded section 200 mm long complete all as specified and as directed. |
| 103 | S&F 4 mm thick sheet glass ordinary quality and glazing complete in square not exc 0.50sqm in each pane complete all as specified and directed. |
| 104 | S&F frosted glass 4.0mm thick, pin head typen exc 0.5 sq.m in each pane and fixed. completeall asspecified and directed. |
| 105 | M&L framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed. |
| 106 | M & L for mild steel powder coated pelmet rods 25mm outer dia including 2 Nos of brackets 2 Nos of pintals or side brackets as per site requirement complete all as specified and directed. |
| 107 | Taking down Chowkhats or frames (pvc/wooden/steel) not exc. 1.5 Sqm each with shutters (Without taking off shutters from the frames) complete all as specified and as directed. |
| 108 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 109 | S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture1.40 mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 110 | S&F steel tubes medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor bore ofpipe 15mm dia. including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete I:2:4 complete incl taking up or down old steel water tubing and connections 15 mm dia complete all as specified and as directed. |
| 111 | S&F steel tubes medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor bore ofpipe 20mm dia. including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete I:2:4.incl taking up or down old steel water tubing and connections 20mm dia complete all as specified and as directed |
| 112 | Supply and fix PVC water tank 1000 Ltrs Capacity Rotational moulded polyethylene water storage tanks cylindrical vertical with closed top hoisted and fixed in position all as specified in SSR Part I,including connecting the float valve of required size, PVC tank cover incl all fittings, 20mm bore GI medium grade overflow pipe and connect to inlet and included fittings outlet pipes, tank nipple, elbow, bend, union, sockets, etc complete all as specified and incl disconnecting existing tank of any description and capacity complete all as specified and as directed. |
| 113 | S & F in repairs 20 mm dia gun metal gate valve with iron wheel screwed both ends for Iron pipe complete all as specified and directed. |
| 114 | M&L Two coats of acrylic distemper over a coat of primer on old / new walls over 1 mm putty, pillasters, cornices, etc., including complete removal of existing treatmentand necessary preparation of surfaces all as specified and as directed. |
| 115 | M&L Two coats of white wash on ceilings including preparation of new decorated surface complete all as specified and as directed. |
| 116 | M&L One coat of cement based paint on old cement painted walls, pillasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed. |
| 117 | M&L One coat of synthetic enamel paint on old painted wooden surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and as directed. |
| 118 | M&L One coat of synthetic enamel paint on old painted steel surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and as directed. |
| 119 | Supply and fixin repairs vitreous china squatting pan Orrisa pattern size 580 x 440 mm white with \"P\" and \"S\" trap front or back inlet etc including provision of PCC (1:5:10) concrete complete all as specified and as directed |
| 120 | S&F in repairs vitreous china wash down water closet (pedestal pattern) EWC white incl plastic water closet seat cover and mild steel chromium plated on aluminium hinging device and connecting to \"P\" or \"S\" incl connecting flush pipe with flushing rim complete all as specified and as directed. |
| 121 | S&F in repairs vitreous china wash basin white flat back size 550x400mm including brackets, waste coupling full or half threded 32mm dia (min wt 45gms) complete all as specified and as directed. |
| 122 | M & L for PVC waste pipe 32 mm dia flexible with cup to fit wash hand basin waste coupling in repair complete all as specified and directed |
| 123 | S&F in repair Bib tap cast copper alloy chromium plated suitable for 15mm bore pipe with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule complete all as specified and as directed. |
| 124 | S&F in repairs brass chromium plated 2-in-1 tap 15 mm bore for fixing of health faucet complete all as specified and as directed. |
| 125 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25meter long flexible tube and ABS wall hook including making connections and fixed in positioncomplete all as specified and as directed. |
| 126 | S&F in repair PVC low level flushing cistern 10 liters capacity (exclusive of brackets), and connections to pipes and fixing of chain and pull, or lever,Joint between flushing pipe and socket of W.C. pan pre-made, if any complete all as specified and as directed. |
| 127 | Supply and fix in repair 15 mm borefancy type pillars taps chromium plated cast copper alloy with capstan head, long screwed shanks complete all as specified and as directed. |
| 128 | S&F in repair chromium plated stop/angle valves cast copper screwed down high pressure fancy type screwed both ends for pipe or union fixed for 15mm bore complete all as specified and as directed. |
| 129 | S&F in repair tubular towel rail alumunium annidised 20mm dia \"D\" type 60cm long between flanges and all as specified and directed. |
| 130 | Dismantaling of PVC/AC drain pipes jointed in cement mortar and taking out from trenches or from walls of any bore including fittings complete all as specified and as directed. |
| 131 | S & F in repairs 75 mm bore PVC (SWR) floortrap plain with grating incl jointing with solvent cement complete all as specified and as directed. |
| 132 | S & F 110mm dia PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed. |
| 133 | S & F 75mm dia PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed. |
| 134 | S & F PVC (SWR)junction single (single T)equal or unequal with access door bore of pipe 75 mm complete all as specified and as directed. |
| 135 | M&L 125/ 110 mm bore PVC (SWR) gully trap incl jointing with solvent cement complete all as specified and as directed. |
| 136 | M & L for Point wiring with PVC insulated FRLS 1.5 sq mm multi stranded copper conductor cable 1100 Volts grade drawn into and including concealedrigid non mettalic PVC conduit/casing caping medium grade not less than 19/20 mm ( ISI marked ) with all fitting and fixing accessories including sunk in pressed steel chromium plated terminal boxes, concealed in wall/surface/roofs/floor/ceiling etc as per site requirement and making & maching the existing surface ) white bakelite sheet cover for mounting switches, Sockets, Fan regulators etc or modular cover plate with frame including sunken boxes suitableto fix modular cover plate with frame , concealed in wall with 1.5 sq mm multi stranded copper conductor cable as continuous earth wire drawn with wiring and connected to common earth dolly complete all as specified and directed for the following :- Make of wire: Polycab/Plaza/HavellsNote:Blanking plate,Modular cover plate ,Switches, sockets outlets, Light fittngs, fans, bells & regulators shall be measured and paid for separetely). |
| 137 | All as per item No. 136 here in before but forone light point/fan point controlled by one way 5 Amp switch complete all as specified and directed. |
| 138 | All as per item No. 136 here in before but for one switch socket outlet 3 pin 5 Amps on independent board complete all as specified and directed. |
| 139 | Supply and Fixmodular switch1 way 6 Amp.1 module, complete all as specified and directed.Make : Legrand/ Crabtree/ Anchor/Indoasian |
| 140 | Supply and Fixmodular Socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed.Make : Legrand/ Crabtree/ Anchor/Indoasian |
| 141 | Supply and fix White cover plate with frame,2/3 module |
| 142 | Supply and fix White cover plate with frame,4 module |
| 143 | Supply and fix White cover plate with frame,8 module |
| 144 | Supply and fix White cover plate with frame,6 module |
| 145 | S & F ceiling rose surface bakelight two to three terminal complete all as specified and directedMake : Anchor/Havells/L&T |
| 146 | Supply and fixingExhaust fan 300 mm sweep 230/ 240 volt AC single phase PVC body 1400 RPM including necessary nut, bolts / screwswriting MES No with synthetic enamel paint all specified and directed.Make : Havells/Bajaj/ Orient/USHA. |
| 147 | S & Fof 4 feet surface mounted batten type luminaire , lumen output of 2000 lumens, high efficiency long life LED package in integral module with lumen efficacy of >100 lm/w, viewing angle not less than 120° to ensure better uniformity with an operating voltage range from 140V-270V. The luminaire shall have a white extrusion housing with a poly carbonate diffuser to provide uniform light and sleek design with width not more than 22 mm. The luminaire shall have a CRI >80, Color temperature 6500K, THD <10% and PF >0.95,SDCM<5, IP20, IK02, Operating Temperature: -10 TO + 45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-55 HZ. The luminaire shall have flicker content<5% and shall have high and low cut off with auto restart feature.Driver Safety requirement stds: IS 15885-2-13. The luminaire shall be EMI/ EMC compliant and shall have a internal surge protection of 4 KV. The luminaire shall have Class-1 Electrical insulation, Class-B serviceability .The luminaire and driver shall be BIS approved, complete all as specified and directed.Make : Philips/ Bajaj / CG/Havells. |
| 148 | S & F of 2 feet surface mounted batten type luminaire , lumen output of 1000 lumens, high efficiency long life LED package in integral module with lumen efficacy of >100 lm/w, viewing angle not less than 120° to ensure better uniformity with an operating voltage range from 140V-270V. The luminaire shall have a white extrusion housing with a poly carbonate diffuser to provide uniform light and sleek design with width not more than 22 mm. The luminaire shall have a CRI >80, Color temperature 6500K, THD <10% and PF >0.95,SDCM<5, IP20, IK02, Operating Temperature: -10 TO + 45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-55 HZ. The luminaire shall have flicker content<5% and shall have high and low cut off with auto restart feature.Driver Safety requirement stds: IS 15885-2-13. The luminaire shall be EMI/ EMC compliant and shall have a internal surge protection of 4 KV. The luminaire shall have Class-1 Electrical insulation, Class-B serviceability .The luminaire and driver shall be BIS approved, complete all as specified and directed.Make : Philips/ Bajaj / CG/Havells. |
| 149 | S & Fbuilding security/ LED street light fitting 36 Watt, 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal, management in multiple optics complete, with IP 65/66 protection complete all as specified and directed. Make: Philips/Bajaj/CG |
| 150 | Supply and fix GI pipe 32 mm dia, medium grade for mounting bracket, bent to shape 1.5 meter length and fixing arrangement with two Nos ofclamps set, nut, bolts, washers,complete all as specified and directed |
| 151 | S & Ffactory madepowder coated distribution board SPN 4 way double door,includingbus bar, Neutral bar, standard DIN rail, earth bar complete including taking down unserviceable DBall as specified and conforming to IS: 8623, all as specified and directed. Make : Legrand/ L&T/ Indo Asian |
| 152 | S & F of MCB single pole and neutral 240 volts 6 to 40 Amps complete all as specified and as directed .Make : Legrand/ L&T/ Indo Asian |
| 153 | S & Fof MCB single pole 240 volts 6 to 40 Amps complete all as specified and as directed .Make : Legrand/ L&T/ Indo Asian |
| 154 | M & L for Cutting existing steel tubing in position without taking down for alterations or additions (Each cut measured) of size 40-50 mm dia GI pipe complete all as specified and as directed |
| 155 | M & L for Screwing existing steel tubing in position without taking down for alterations or additions (or lengthening screw on pipe to form connector) of size 40-50 mm dia GI pipe |
| 156 | Supply and fixingChlorinated PVC Union of size 25 mm dia, ISI marked complete all as specified and as directed. |
| 157 | Supply and fixingChlorinated PVC Tank adoptor of size 25 mm dia, ISI marked complete all as specified and as directed. |
| 158 | Material and labour for Spreading ribbed soil in trenches as in cable cushioning all as per IS 1255-1983, complete all as specified and directed.Note :- (i)Excavated approved soil shall be ribbed by using sieve to separate composite particles etc. as per IS and refilling in trenches before laying of cable 8 CM and 15 CM after laying of cable. This is then gently punned down to a depth of 10 cm above the top of upper most cable (ii) For the purpose of measurement only punned thickness shall be considered for payment. |
| 159 | Material and labour for well burnt bricks ‘B’ class as mechanicalprotection to under ground cables laying with length of the bricks equal to the width of the trench, complete all as specified and directed. |
| 160 | Material and labour for Cutting existing road/PCC/Drain for laying of GI or any type of pipe including necessary earthwork, excavation exc 600mm depth but not exc 1mtr depth, 800 mm wide including making good existing surface with 150 mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate, complete all as specified and directed. Note :-The tenderer shall take into consideration for following points while quoting rate for this item andthe unit rate is deemed to be inclusive for :-(i) Earth work and excavation in any type of soil(ii) Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick ,complete all as specified and as directed.(iii) Removing excavated material out side MD land.(iv)Laying of any type/any bore of pipe in trenches including taking down existing unserviceable pipe. Supply of pipe shall be measured and paid separately(v)150 mm thickPCC 1:2:4 type B1 using 20mm graded stone aggregate as inroad to make good existing disturbed surfaces. |
| 161 | Supply only of GI pipe light grade for cable protection of size 50 mm bore with fittings, complete all as specified and directed. |
| 162 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6.0 sq mm 4 core complete all as specified and directed. |
| 163 | Supply, installation, testing & commissioning of maintenance free chemicalearthing system comprising of 17mm dia copper bondedrod 3 mtr long horizontally pre welded T-terminal rod with provision for connection size of 50 x 150mm long, 6mm thickness with equal space either side, with 12mm dia hole of 02 numbers each on either side of the terminal clamp with 250 microns (average) coating thickness, tested and certified by CPRI India alongwith 50 Kg earth energizer compound and 10 litres earth resistance reducingliquid. The earthing energizer compound and resistance reducing earthing liquid shall be tested as per IEC-62561-7 read with ASTM G57-06, CI 3.4 A by any NABL accredited lab. The above mentioned rod shall be installed in 4-6 inch bore, 12 feet depth with a distance of minimum 3 meters between each installation, complete all as specified and directed..Make : Model HTSP 317 of safeTrode or equivalent in Snaga/ Cubes 6 Global |
| 164 | The quoted rate shall also deemed to be included the following :- (i)Prior toinstallation of maintenance free chemicalearthing, soil resistivity test to be carried out at the location where earthingwork to be donein presence of Engr-in- Charge/JE (E/M),user and the report has tosubmitto Garrison Engineer with recommendation of manufacturer, if required additional interconnection ofearthing (not more than 08 number of earthing) to achive earth result less then 1 Ohms. The arrangement done for soil resistivity testingandsubmission of report with recommendationdeemed to be included in the quoted rate. |
| 165 | (ii) The description/ size/ qty of items mentioned in above are for indicating only however qty/ size may vary at site condition to maintain the earth resistance 1 ohm. The contractor shall quote rate by considering all factors. |
| 166 | (iii) Rateofearth energizer compound of 25 Kg of 02 bags and earthresistance reducingliquid 10 litre per cane for each pit deemed to be included in the quoted rate. |
| 167 | (iv)Resistivity of earth energizer compound and resistance reducing earthing liquid shall be certified by any NABL accredited lab carried out as per IEC-62561-7 read with ASTMG57-06, CI-3.4A and the certificate of same shall be submitted by the contractor along with the sample approval |
| 168 | (v) Earth enhancing material should not leach into the adjacent soil or underground water channels and its PH value should be in neutral range complete all as specified and as directed. It should solidify when mixed with water and set like concrete. |
| 169 | (vi) Copper strip of size 20 x 3 mm shallbe fixed on proper post insulator at the instrument end (copper strip upto 7.5 RM shall be considered in unit quoted rate and extra will be measured and paid separately). |
| 170 | (vii)Testing of earth shall be carriedout in presence ofdepartmental and user representativeand report shall be submitted to Garrison Engineer duly signed by all concerned. |
| 171 | (viii)Earth resistance tester will be provided by the contractor.Tester should be calibrated from authorised company/ lab. |
| 172 | (ix)Earthing shall be tested after completion of work by the contractor in presence of Engr-in-charge, user and proper record shall be maintained duly signed by all concerned.After testing if the desired earth resistance of less than 1 Ohm is not obtained, the earthing will be redone at no extra cost to Govt. till desired result is obtained. |
| 173 | (x) The contractor shall give a written guarantee of minimum three years for maintaining the earth resistance less than 1 Ohm after certified date of completion. |
| 174 | (xi) No further maintenance or periodic watering or recharge shall be required in earthing during its guarantee period of over 03 years in all type of soil including soft/ disintegrated or hard rock. |
| 175 | (xii) During the guarantee period, if earth resistance is not maintained less than 1 ohm the contractor has to redo or rectify at no extra cost to Govt till desired result is maintained. |
| 176 | (xiii) A security deposit of value equal to 2.5 % of the rate quoted for chemical earthing for each earthing shall be retained from payment due to the contractor from final bill for the guarantee period. |
| 177 | (xiv) The electrode shallcarry manufacturer\"s name . |
| 178 | (xv) The connection clamp shall be permanentlly welded to the copper boundedrodto avoid any kind of connectivity loss,.The pre-welded copper bounded rod shall not need any additional clamp for termination. |
| 179 | (xvi) The acceptable earth resistance at earth busbar/ test point shall not be more than 0.1 ohm. |
| 180 | (xvii)Earth work such as auguring andmaking good the surrounding area shall carried out in any type of soil. |
| 181 | (xviii)The contractor shall submit CPRI India certified document for copper bounded rod to ensure genuineness of material. |
| 182 | (xix) Sign boardof mild steel sheet 2 mm thick duly painted with two coats of synthetic enamel paint over a coat of red oxideZinc chrome primer showing result of earthing shall be fixed near the earth pit after completion as directed by engr -in- charge. |
| 183 | Material and labour for Earth pit cover madeof heavy duty poly plastic of high grade polypropylene tested and certified by any NABL accredited lab for load bearing capacity not less than 7.2 tonnes with top dia not less than 250mm, bottom dia not less than 330 mm and height not less than 260 mm for each electrode pit complete all as specified and directed.Make : Model SEPC 250 of SAFE TRODE or equivalent in Snaga/ Cubes 6 Global |
| 184 | S&F copper strip 20 x 3mm thick as earthing lead fixed to wall/roofs etc, complete all as specified anddirected. Note : - All Joints should be joined by Exothermic Welding or Brazing. |
| 185 | Note :- An amount of Rs 3,288.00 on account of credit schedule for schedule \"A\" part II shall be deducted from the total amount of BOQ to arrive at the contract sum. |
AI Tender Summary
Tender Timeline
Aug 14, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedSep 04, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedSep 11, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender