Tender For Addn/Altn To Toilet At Offers Ward Certain Maj Rev And Minor Works At Chafb; 1 COMMON ITEMS APPLICABLE FOR JOB A , JOB B, JOB C, JOB D, JOB E, JOB F & G 2 Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level andremovingmaterial from site complete all as specified and directed. 3 Taking down wooden chowkats or frames areanot exceeding 1.50 Sqm(w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar 1:3 or PCC 1:2:4 type B1, complete all as specified and as directed. 4 Taking down wooden chowkats or frames area exceeding 1.50 Sqm andnot exceeding 4.00 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar 1:3 or PCC 1:2:4 type B1, complete all as specified and as directed. 5 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed. 6 M&L for Non - skid White Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed. 7 M&L for White Glazed ceramic tiles in vertical surface 350x 250x7 mm/ 450X 350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to matchincluding 10mm thick cement plaster in cement mortar 1:4 as backing coat on fair faces on stone surface all as specified and directed. 8 Demolition ofbrickwork or stone/boulder masanory, laid dry below or above ground level andremovingmaterial from site complete all as specified and directed. 9 M&L for Brick work with subclass B bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed. 10 M&L for providing cement concrete type B1, 1:2:4 mix (20mm graded aggregate) in coping including necessary use and waste of form work complete all as specified and directed 11 M&L for 10 mm thick rendering for fair faces of concrete surfaces on walls in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and directed. 12 M&L for preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion on walls over a coat of chalk primer whitening upto triple storeys bldg complete all as specified and directed. 13 S&F in repair, Bib tap screwed down high pressure, cast copper alloy,fancy type, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified and directed 14 S&F in repair gun metal Gate valves, with iron wheel head, screwed both ends for iron pipe flange ends type fixed of 20mm dia complete all as specified and directed. 15 Taking up or down steel tubing and connections of 15mm bore including cleaning for refixing or removal to store provision for branch connection by inserting tee union elbow etc complete all as specified and directed. 16 S&F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed. 17 S&F 150 mm long Extruded aluminiumalloy handles, fabricatedtype anodised complete all as specified and directed. 18 S&F 100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and directed. 19 S&F Alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified and directed. 20 S&F in repairs double legged door stopper of overall length of cover plate 150 mm of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floors and rubber complete all as specified and directed. 21 S&F 4mm thick figured glass, ordinary quality and glazing rubber beading in square nexc 0.5 sqm in each pane complete all as specified and directed. 22 S&F in repairs PVC (SWR) floor trap 75/110mm dia, with SS grating including jointing to waste pipe fixed in cement concrete type B1 ,1:2:4 complete all as specified and directed. 23 S&F PVC (SWR) bends any radius 75mm dia complete all as specified and directed. 24 S&F in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate complete all as specified and directed. 25 Demolition of Reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcementas required to facilitate demolition, complete all as specified and directed. 26 M&L for providing reinforced cement concrete 1:2 :4 type B1 using 20mm graded stone aggregate as in cooking platform slab supported on wall, beam, cantilevers and kitchen cooking platform including necessary formwork complete all as specified and directed. 27 S&F Mild steel TMT bars, 8 mm dia, cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm diaor securing with clips, complete all as specified and directed. 28 Taking down cement plaster from brick walls ,concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed. 29 M&L 15mm thick rendering in cement mortar 1:6 onbrick or concrete surface of any description, finished the surface even and smooth without using extra cement complete all as specified. 30 M&L Preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty, complete all as specified and directed. 31 Removing building materials etc, (other than spoil like bricks, stone, aggregate, stone slabs etc.) to a distance of upto and incl 2000m, including loading, unloading and stacking at the destination,complete all as specified and directed. 32 Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed. 33 Excavating in post holes (or similar holes) each n.exc 0.50 cum, getting out in hard/dense soil, returning filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25cm thick, complete all as specified and directed. 34 Excavation in trenches not exc 1.5m wide and n. exc 1.5m in depth, for foundation, etc. or for shafts, wells, cesspits, manhole, pier holes, etc. n exc 10 Sqm on planand getting out in hard/dense soil complete all as specified and directed. 35 Removing excavated material n exc 50 m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed. 36 Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil complete all as specified and directed. 37 M&L for Plain cement concrete type D-2 1:4:8 using 40mm graded aggregate as in foundation filling, sub base and mass concrete complete all as specified and directed. 38 M&L Rendering 15mm thick on fair faces of concrete block masonry in cement concrete 1:4 in two layers first coat 10mm thick in cement mortar 1:4 and second coat 5 mm thick in cement mortar 1:4 mixed with WPC @ 3% by weight of cement and finished fair and even complete all as specified and directed.Note : Water Proofing compound shall be measured and paid seperately 39 Supply only Liquid water proofing compound complete all as specified and directed. 40 S&F steel work in tubular truss including special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS 1161-1979 grade st 240 etc confirming to fe-410-W (Gde-E-250) quality-A and also incl fixing arrangements with dash fastners screws wherever reqd complete all as specified as directed. 41 M&L Plain cement concrete 1:3:6 type C-2 using 40 mm graded mechanically crushed stone aggregate as in foundationfillingand mass concrete for making base to the vertical members on roof etc including necessary use and waste of formwork etc complete all as specified and directed. 42 S&F MS Roof trusses, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee angle, channel or flat sections as in wind ties etc.) including distance pieces, cleats etc. confirming to Fe-410-W (Gde-E-250) quality-A complete all as specified and directed. 43 S&F Mild steel plain plates in available sizes (any thickness) confirming to Fe 410-W (Gde-E-250) quality-A as in base support to vertical members and support to horizontal members fixed to wall incl necessary welding etc complete all as specified as directed. 44 M&L for two coats of synthetic enamel paint on new steel surfaces over acoat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth, complete all as specified as directed. 45 S&F Pre-painted galvalume aluminium zinc coating (AZ-150) GI based corrugated steel sheet 0.50 mm thick of any colourhaving 550 Mpa tensile strength as in roof covering/cladding and fixed with self tappingscrews, complete all as specified as directed. 46 Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws allcomplete as per architectural drawings and the directions of Engineer-in-Charge complete all as specified as directed. 47 S&F foranodised aluminium grill of (anodised transparent or dyedto required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/ pattern, with approved standard section and fixed to the existing window frame with C.P. brass / stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised alumiinium standard section around the opening, all complete as per requirement and direction of Engineer encharge. 48 S&F TMT bars 10mm diaand over, cut to length,bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed)not less than 0.90mm dia complete all as specified as directed. 49 M&L for 25mm thick PCC type B-1, 1:2:4 (using 20mm graded aggregate) as in sub base, complete all as specified as directed. 50 M&L for 75 mm thick(compacted thickness) WBM, with coarse aggregates of grading 2 (63 to 40mm size) of flint or quartzite stone spread, watered, rolled with 8 to 10 tonne power rollerand consolidated to gradientand camber required complete all as specified as directed. 51 M&L for PCC coloured interlocking (glossy finishing) paver blocks with grey cement and no pigments confirming to IS-15658-2006 of 60 mm thickness, M-35 grade asin hardstandingetc. laid over and including 50 mm thick screed or bedding layer of sand, complete all as specified as directed. 52 Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge complete all as specified as directed. 53 M&L for Precast cement concrete block masonry with soild blocks, type C1 1:3:6 using 20mm graded aggregate exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed. 54 M&L for point wiring concealed type with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable connected to common earth and earth dolly with suitable copper lugs drawing into and including rigid non-metallic PVC surface conduit of 20mm dia or higher, medium grade complete with all PVC conduit accessories, metal flush box of 1.60 mm thick suitable for modular switches/ sockets/fan regulators incl modular white cover plate and modular metal flush box with frame of required modules with, blanking plates,brass screws, cup washers etc including all cutting / chases etc in stone/ brick masonary/ walls and making good to the disturbed surfaces to match the existing complete all as specified and directed for the following:- 55 One light point controlled by one, one way switch 06 Amps. 56 One fan point controlled by one, one way switch 06 Amps. 57 One 3 pin, 06 Amps socket outlet point on independent board controlled by one, one way 06 Amps switch. 58 One 3 pin, 06 Amps socket outlet point on same board controlled by, one way 06 Amps switch. 59 All as per Item no 55.00 here-in-before but point wiring with 2.5 Sqmm single core FRLS cables and earth continuity wire of 2.5 Sq mm single core FRLS cable for one 3 pin 15 Amps socket out let point controlled by one, one way switch on independent board complete all as specified as directed. 60 S&F Modular switch, 06 Amps, single pole, one way, 230 volts, one module complete all as specified as directed. 61 S&F Modular socket outlet 05 Pin, 06 Amps, 02 module with shutter complete all as specified as directed. 62 S&F Modular switch, with indicator, 16 Amps, single pole, one way, 230 volts complete all as specified as directed. 63 S&F Modular socket outlet, 02 in 01, 03 pin, 16 Amps, 02 module with shutter complete all as specified as directed. 64 S&F Ceiling rose, 66 x 50mm surface type with three terminals complete all as specified as directed. 65 S&F on surface and wall mountedLED batten with polycarbonate housing and initegrated electronic drive20 Watt fixture 4 feet, 5700 K, provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver and all accessories pre-wired including connection with 2 core flexiblecopper conductor cable of suitable size from ceiling rose complete all as specified as directed. 66 S&F MCB, SP, AC, 240 volts of 06 to 32 Amps capacity B curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified as directed. 67 M&L for sand filling (pulverized stone dust) under floors or in foundations and cushioning incl spreading & levelling for protection of cable complete all as specified as directed. 68 ITEMS APPLICABLE FOR JOB A 69 Material & Labour for Green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shade of following types and including 15mm thick screed bed in cement mortar 1:6set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces complete all as specified and directed. 70 M&L for Brick work with Subclass B bricks, straight or curved on plan to any radius in half brick thick wwalls, built in CM 1:4 complete all as specified and directed. 71 M&L for 75 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished complete all as specified and directed.Note : Joints 12 mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection. 72 S&F 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floors including taking down of old GI tubing, 40 mm bore complete all as specified and directed. 73 S&F in repairs Polymer coloured (Polypropeylene Delrin and ABS) low levelflushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet ball valve float valve bends brackets, rawl plug, brass screws handle etc complete having BIS description mark with 2731 with and including suitable size of MS brackets, plug, screws all as required incl taking down existinghigh level/low level flushing cistern any type disconnecting pipes and jointingwith new one etcand making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with Water closet of any type complete all as specified and directed. 74 S&F in repairs Vitreous ChinaWHB white oval type counter below type of size 570 x 445 mm including waste coupling, waste pipe and brackets etc complete all as specified and directed. 75 S&F in repairs Vitreous china premium quality/1st quality wash down water closet pan (pedestal pattern), white (excluding flushing cistern & flush pipe) &incl 01 No ‘P’ or ‘S’ trap of dia 100mm includingprovn of lime concrete bedding, complete all as specified and directed. 76 S&F in repairs,15mm bore pillar tap, fancy type, chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks ,complete all as specified and directed. 77 S&F in repair Angle cock 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions,complete all as specified and directed.Note : Weight of cock shall not be less than 0.575kg. 78 S&F in repair brass chromium plated tubular towel rail 20mm dia D type 60cm long between flanges complete all as specified and directed. 79 S&F in repair Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) capacity 500 Ltrhoisted and fixed in position after dismantling (water tank of cap exc 250 ltr and n.exc 500 ltr) and removing to store and complete all as specified and directed. 80 S&F in repair PTMT ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes complete all as specified and directed. 81 S&F in repair for 5.5 mm thick looking mirror of selected quality, bevelled edge 600mmx450mm glass mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screw and cup washer, pvc beading & rubber packing complete all as specified and directed. 82 S&F in repair Vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed. 83 S&F in repairs, Urinal spreader of Brass chromium plated for fixing with 15 mm dia pipe complete all as specified and directed. 84 Taking up or down steel tubing and connections of 20 mm bore including cleaning for refixing or removal to store provision for branch connection by inserting tee union elbow etc complete all as specified and directed. 85 Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 16mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor to the entire satisfaction of Engineer-in-charge complete all as specified and directed. 86 S&F Steel Tubes 20mm bore, medium grade, galvanised, with all fitting; laid in trenches and fixed complete to brick/stone wall or laid in floor concealed, complete all as specified and as directed.. 87 Refixing old steel tubing of 20mm bore and connections in new or old position (Walls, ceiling, floors, etc complete all as specified and as directed.. 88 S&Fin repair PVC connections 45cm long including 15mm bore PTMT nuts on both ends complete all as specified and as directed.. 89 S&F in repairs Stainless steel grating openable 100mm dia without hole including fixing with white cement complete all as specified and as directed.. 90 S&F in repair glass shelf assembly consisting of made out of 5.5 mm thick glass shelf 12 cm wide with chromium plated bracket guard andrailing 60cm long complete all as specified and directed. 91 S&F in repair CP brass soap tray fixed with brass screw complete all as specified and as directed. 92 S&F Factory made PVC hollow door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of extended 5 mm rigid PVC foam sheet cut at corner and jointed with 02 Nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided through out the frame and fixing to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos. of screws to be provided for each vertical numberand minimum 02 Nos. for horizontal member), complete all as specified and as directed. 93 S&F Factory made solid PVC moulded door shutter with wood free EPS 28 to 30 mm thick (Stiles), with 2, 4, or 6 raised panel design with 2 mm thick moulded PVC sheet on the front page and 2 mm plane colour PVC sheet on back face supplying and fixing in frames at site complete all as specified and as directed. 94 S&F Powder coatedaluminiumwindows/ventilator/partition etcfixed/openable type or sliding without sash bar, aluminium sectionweighing 0.55 kg/m including necessary jointing cleats, glazing clip,rubber packing, anodised aluminium snap beading, screw etc complete all as specified and as directed. 95 S&F Galvanised mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staple orfixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified and as directed. 96 Dismantling of PVC (SWR) pipes, and taking out complete all as specified and directed. 97 S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed . 98 S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.. 99 S&F PVC (SWR) bends any radius 110mm dia complete all as specified and directed . 100 S&F PVC (SWR), junction single, (Single T) equal or unequal 110mm dia complete all as specified and directed . 101 S&F PVC (SWR), junction single, (Single T) equal or unequal 75mm dia complete all as specified and directed . 102 S&F PVC (SWR) vent cowl 75mm dia complete all as specified and directed. 103 S&F PVC (SWR) vent cowl 110mm dia complete all as specified and directed. 104 S&F Stack clamps out of 40 x 4 mm flat iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100/75mm bore complete all as specified and as directed. 105 M&L 10 mm thick cement mortar 1:3 on ceiling,finished even and smooth without using extra cement complete all as specified and as directed. 106 M&L for preparing new plastered surfaces of ceiling and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty on ceiling completeall as specified and directed. 107 M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper (acrylic) white or tinted over a coat of priming over a coat of 1 mm thick wall care putty on walls upto tripple storeys bldg complete all as specified and directed. 108 M&L for preparation of old Plastered or un-plastered surfaces ofceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty complete all as specified and directed. 109 Taking down carefully copper/aluminiumpoint wiring (light fan socket or power) complete including fittings & fixturessuch as switches, ceiling rose, pendants, regulators, sockets, ceiling roses,pendants, regulators, light fittings etc and making good disturbed surfaces of walls, floors, etc complete all as specified and directed. 110 S&F Exhaust fan 380 mm sweep heavy duty, steel body, AC, single phase 230 volts, 50 Hz, with blades, frame and louvers shutter with making necessary hole in wall of required size suitable for exhaust fan with required civil wk and making good the disturbed surfaces complete all as specified and directed. 111 S&F Water heater storage type (geyser), capacity 25 litres, 230 volt, AC, BEE 5 star rated, Powder coated metal body, temperature indicating dial, fire retardant cable, efficient long life Copper heating element, Shock proof & Rust proof ABS body, to be fixed on wall with suitable size of nut/ bolt / fasteners and washers incl making good the disturbed surfaces of wall incl necessary cold and hot water connection with 02 Nos heavy duty connection pipe of SS rope threaded type with brass unions at both ends, 45 cm long, 15mm bore complete all as specified and directed. 112 S&F in replacement for sub main wiring with 10.00 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable with and including continuous earth wire of size 10.00 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable drawing into and including rigid non-metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories and connected to common earth dolly with suitable copper lugs including all cutting / chases etc in walls and making good to the disturbed surfaces to match the existing complete all as specified & directed, including taking down old sub main wiring complete all as specified and directed.Note-Two runs of 10.00 sqmm single core cable and one run of 10.00 sqmm earth wire including PVC conduit together shall be measured as one unit. 113 S&F Sheet metal enclosure with socket plug top and MCB, Single pole & neutral enclosure with a 2 pin & earth plug & socket complete with one single pole MCB 20 amps complete all as specified and directed. 114 S&F in replacement sheet metal enclosure distribution board, single pole and neutral, AC, 240 volts, 08 way, with 200 Amps rated copper bus bar and double door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall complete all as specified and directed. 115 S&F in replacement MCB SPN 40 amps, 240 Volts, AC of breaking capacity 10 KA,C curve and connections by using suitable copper lugs complete all as specified and directed. 116 ITEMS APPLICABLE FOR JOB B 117 M&L for preparation of new or prevously untreated plastered surfaces of walls /jallies/louvers etc and applying two coats of cement base paint , white or tinted complete all as specified and directed. 118 S&F 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 65 mm x 125 mm(moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by Rajshri/Echon or Eq an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed ; Material test certificate and authentication should be compoulsory provided by the manufacturing company complete all as specified and directed. 119 S&F IInd class hard wood 35mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed. 120 S&F IInd class hard wood factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed. 121 M&L Repair to RCC 1:2:4 type B-1 using 20 mm gradedstone aggregateas in chajjas beams etc upto tripple storey bldgs including necessary formwork complete all as specified and directed. 122 M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, over and including cement screed bed 15 mm thick in cement mortar 1:6 baseincluding rubbing and mirror polishing, and half nose moulding (bull nosing) etc complete all as specified and directed. 123 All as per item Sl no 124.00 here-in-before but pre-polished kota stone as in vertical surfaces such as skirting and risers over and including 10mm thick plaster in cement mortar 1:4 onbrick work or concrete surfaces, complete all as specified and directed. 124 M&L for Granite work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, counter basins, urinal partitions etc. and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shade of following types and including 15mm thick screed bed in cement mortar1:6set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces and half nose moulding (bull nosing) etc, complete all as specified and directed. 125 S&F Wall fan, 400 mm sweep, 230/240 Volt, single phase, 50 watt, 1320 rpm, air delivery 70 CMM, oscillating type, 3 speed push button control, to be fitted on wall with necessary arrangements incl connection complete all as specified and directed. 126 S&F Ceiling fan complete with three blades,down rod, accessories230 V, 1200 mm sweep, min air delivery 210 CFM, BEE 5 star rated with brushless direct current motor incl connection complete all as specified and directed. 127 S&F Ceiling fan regulator, stepped type of 0 to 04 rotary steps, electronic, 02 module, humfree, AC, 230 volts, 100 watts complete all as specified and directed. 128 S&F Energy saving security light fitting of 35 watts LED pressure die-cast aluminium IP 66 roadway luminaire with high power LED as light source comprising with electronic driver and all accessories pre-wired incl connecting up with PVC insulated copper conductor cable 1.5 Sqmm, 3 core as required for connections and 50 mm bore light grade G. I. tube mounting bracket of 1.5 meter in length, bend to shape at 140 degree in ‘L’ shape and fixed to wall by means of 02 nos. of 40 x 5 mm flat iron clamps, nuts, bolts and washers etc complete all as specified and directed. 129 Supply and laying cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sqmm 4 core complete all as specified and directed.(Note :- Excavation & earth work, sand cushioning, bricks protection & GIpipe where required shall be measured & paid seperately) 130 Excavation in trenches not exc 1.5 Mtr wide and n.exc 1.5 mtr in depth, getting out for electric cable complete in any type of soil complete all as specified and directed. 131 Supplying and laying un-reinforced precast concrete cable cover, class LV, Type I, flat, size 250mm x 150mm x 40mm complete all as specified and directed. 132 S&F GI tubing light grade with all necessary fittings laid in trenches/under road crossing/fixed on pole/wall/under floor including suitable mild steel FI clamps of required size complete for size 40 mm bore complete all as specified and directed. 133 S&F sheet metal enclosure distribution board triple pole and neutral (VTPN), AC, 440 volts, 04 ways with 200 Amps rated copper bus bar and metal double door suitable for MCCB 63 amps as incomer and MCB SPs as outgoing along with cable end box for above DB and flush to wall including all cutting etc in wall complete all as specified and directed.(Note : MCB TPN & MCB SPs shall be measured and paid seperately) 134 S&F MCB TPN, AC, 415 volts of 40 Amps capacity B curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified and directed. 135 M&L for Earthing complete with galvanised steel earth electrode plate of size 600x600x6mm thick, buried directly in ground(earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.50m below normal ground level, connected to galvanised iron wire 4 mm dia as earth lead up to test point with suitable size GI nuts/bolts, washers,check nut and brazed properly up to main board,LT panel etc and adequate quantity of charcoal and salt 15 cm around the earth plate including earth pit in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregates,40mm thick precast RCC cover in 1:2:4 reinforced with 8mm dia TMT bars 3 Nos both way including CI cover 10 mm thick with hingedand frame of angle iron 25x25x6mmwith 6mm dia MS bar handle made to shape, excavation and earth work in any type of soil and including medium grade GI watering pipe 20mm bore with funnel and wire mesh and medium grade GIprotection pipe 15 mm bore up to main board complete all as shown in electrical plate no 3 of MES schedule Part-I , connected to earthing testing point and testing on completioncomplete all as specified and directed.Note: (i) The unit rate shall be included 15 mm dia GI pipe up to 7.5m for protection of earth lead. (ii) The unit rate shall be included galvanised iron wire 4 mm dia from earth electrode to test point up to 7.5 meter (iii) In case measured value of earth resistance of each earthingis recorded more than 3 ohms then the earthing shall be re done by the contractor without any extra cost to the department. 136 ITEMS APPLICABLE FOR JOB D 137 M&L Reinforced cement concrete Type B-1, 1:2:4 (using 20mm graded aggregate) Nominal Mix as in chajjas canopies, deck slabs and in shelves and the like upto and incl 7 storied bldgs, complete all as specified and as directed. 138 M&L for Providing pre-cast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed)type C1, 1:3:6 ( 20 mm graded aggregate)and setting in mortar 1: 6 , complete in walls complete all as specified and as directed. 139 use and waste of formwork to Kitchen cooking platform, chajjas, troughs and similar items including edges etc, complete all as specified and as directed. 140 S&Fin repairs sink with drain board made of stainless steel,1.0 mm thick for kitchen or laboratorty,with plug,waste pipe,washers including bedding in cement mortar to dwarf wall or including fixing cantilever cast iron brackets, and connecting union to pipe etc overall size915x460mmh bowl size 410 mmx330 mmx160 mm complete all as specified and as directed. 141 S&F Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm 45gms/40mm-60 gms) complete all as specified and as directed. 142 S&F in repairs PVC waste pipe 40mm size for sink complete all as specified and directed. 143 S&F stainless steel plate rack of size 990.60mm x 914.40mm including fixing to wall as directed etc complete all as specified and as directed 144 S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples incuding necessary wooden beading complete all as specified and as directed 145 Supply only 4.80 mm Sheet glass, ordinary quality and glazing with glazing clips, rubber packing in square exc 0.5 sq. m in each pane complete all as specified and as directed 146 S&F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed. 147 M&L Granite slab work 18 to 20mm thick in floors, steps, door/window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over & including screed bed 15mm thick in cement mortar 1:6, complete all as specified and directed. 148 Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed 149 M&L for preparation of new plastered surface of wall and applying two coats of oil bound distemper over a coat of chalk primer whitening complete all as specified and directed. 150 S&F Steel Tubes 15mm bore, medium grade, galvanised, with all fitting; laid in trenches and fixed complete to brick/stone wall or laid in floor concealed, complete all as specified and as directed. 151 Dismantling of cast iron or reinforced concrete drain pipes or PVC (SWR) pipes of any size and bore, jointed in cement mortarand taking out complete all as specified and directed. 152 S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints fixed to walls in verticial surfaces of upto and incl 7 storied bldgs, complete all as specified and directed. 153 S&F PVC (SWR)bends with access door any radius 75mm dia complete all as specified and directed. 154 S&F PVC (SWR)branch piece, single (single Y) 75mm dia complete all as specified and directed. 155 ITEMS APPLICABLE FOR JOB E 156 Dismantling wrought iron or mild steel work of any description not otherwise special complete all as specified and as directed 157 Dismantling plain or corrugated steel sheeting any guage, thickness including roof covering etc complete all as specified and as directed. 158 Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets, any thickness including cover fillets etc., complete all as specified and directed. 159 M&L Plain cement concrete type B-2, 1:2:4 (40 mm graded aggregate) as in copings pilast,roof kerbs , buttresses columns, pillars, boundary pillars and posts (incl caps and bases) complete all as specified and as directed 160 M&L for providing, cement concretetype B-0 1:2:4 using 12.5mm graded stone aggregate asin roof kerbs, padding or mud stops, rounded or chamfered on edges complete all as specified and as directed 161 M&L for Rendering 10mm thickin cement mortar 1:6 and5mm thick in cement morter 1:4 in two layers on fair faces of brick work or concrete surfaces with water proofing compound @ 200 ml per 50kg of cement or as per manufacturers instruction etc finished even and smooth without using extra cement complete all as specified and as directed.Note : WPC shall be measured and paid separetely.Scaffolding upto tripple storey.contractor may quote rate accordingly. 162 M&L Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.;and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth complete all as specified and directed. 163 S&F 8-9 mm thick Prepainted gypsum building boards of size 595 x 595mm PVC laminated at back side of boardinsulation & acoustic purposeflat in ceiling fixed or laid / includingpowder coated GI snap grid of size605mm x 605mm frame work using 36.50 x 23.50 x 1.5mm main Tee, 23.50 x 23.50 x 1.5mm cross Tee and 25x25x1.5mm angles for false ceiling with screws fixed to false ceiling including hangers 4 mm dia G.I (upto 1.5m length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, complete all as specified and directed. Note: The rate shall be inclusive of scaffolding and necessary arrangements. 164 S&F Mild steel plates (plain or chequered) channels,distance pieces, cleats etc.square cut or notched including riveted, bolted or welded attachment complete all as specified and directed. 165 M&L for water proofing treatment on horizontal and vertical surfaces with applying of oil bound bitumen primer @ 0.20 Kg/Sqm and providing4mm thick APP modified water proofing membrane weighing not less than 4.0 Kg/Sqm reinforced with non woven polyester matt weighing not less than 160 grm/Sqm having softening point not less than 150 degree centigrade, having tensile strength of 650 N/cm2 and 350 N/cm2 in longitudinal and transverse directions respectively of the reinforced tearing strength of 180N by torch on application including minimum 10cm side over lap and 15 cm end lap applying a coat of blown grade hot bitumen 90/15 over the membrane @1.20 Kg/Sqm finished with solar reflective bituminus paint/primer @ 0.10 kg per sqm incl dismantling of existing APP membrane complete all as specified and directed. 166 M&L for preparation of new plastered surfaces of wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primig paint complete all as specified and directed. 167 M&L for applying2 mm thickwall care putty on wallincluding preparation old /new surfaces plastered or unplasteredsurfaces , complete all as specified and directed. 168 M&L forpreparing old plastered or unplasteredsurface of walls and applying two coats of Cement base paint on walls complete all as specified and directed. 169 M&L preparation of plastered or unplasteredold decorated surfaces of walls by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds , moss & efflorescent salts & treating oily & greasy spots & filling holes& cracks with suitable material like white cement orPlaster of Parisand applying two coats of oil bound distemper through mechanical means including necessary scaffolding upto 6th storey complete all as specified and directed. 170 M&L for preparing newplastered or unplastered old surface of walls and applying two coats of Cement base paint on walls including with alkali resistant priming paint complete all as specified and directed. 171 ITEMS APPLICABLE FOR JOB F 172 M&L Reinforced cement concrete Mix Design (M-20) using 25mm graded aggregate as in walls, retaining wall, basement walls, ballast walls and the like any thickness above top of footings, including attached pilasters and buttresses, complete all as specified and as directed. 173 Use and waste of Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc, vertical or to batter finished rough and flat, complete all as specified and as directed. 174 M&L Double charged Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to, in floors etc. set and jointed in neat cement slurry and inted in white or coloured cement to match over and including 15mm thick screed bed incement mortar 1:6 complete all as specified and directed. 175 All as per Sl Item No 179.00 but in skirting to walls including 10mm thick cement plaster in cement mortar 1:4 as back coat on fair faces on stone surface complete all as specified and directed. 176 S&F 12 mm thickprelaminated (both sides with decorative choice) particle board, interior grade, fixed with screws or securing with beading for aluminium partition wk etc, complete all as specified and as directed. 177 S&F 5.5 mm thick plain sheet glass, ordinary quality and glazing rubber beading in square exc 0.5 sqm in each pane complete all as specified and as directed. 178 S&FDouble action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, ISI marked complete all as specified and as directed. 179 M&L 5 mm thick rendering for fair faces of concrete surfaces on ceiling in cement mortar 1:3 for fair finished surfaces complete all as specified and as directed. 180 M&L for preparation of old or prevously untreated plastered surfaces of walls including complete removal of existing treatment and applying two coats of Oil bound distemper Emulsion over a coat of 1 mm thick putty on newly plastered wall surfaces, complete all as specified and directed. 181 All as per Sl Item No 185.00 here-in-beforebut on ceilings. 182 M&L for preparation of new or previously untreated plastered surfaces of walls and applying two coats of cement base paint , white or tinted complete all as specified and directed. 183 M&L for preparation of old or prevously untreated plastered surfaces of walls including complete removal of existing treatment and applying two coats of cement base paint , white or tinted complete all as specified and directed. 184 M&L50 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished surface complete all as specified and as directed.Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection. 185 M&L for broken stone or boulders hardcore of gauge not exc 63mm, deposited spread and levelled in layers not exc 15cm thick, watered and rammed to a true surface complete all as specified and as directed. 186 M&L 75mm thick cement concrete type D-2 (1:4:8) (using 40mm graded crushed stone aggregate) as in sub base complete all as specified and as directed. 187 M&L for lead (Pb) lining door made up of 35-40mm thick IInd class hard wood finished with decolam choice on top both side including taking down, removal of existing door as well as necessary fixing of iron mongry as per site requirement complete all as specified and directed.Note:The lead sheet upto 5mm thicktypically will be sandwiched between frame material of wooden door as elaborated above to reduce the radiation level within the permissible limits as per the AERB guidelines .Size of the lead (Pb) door may vary upto 1.5m in width and upto 2.20 mtr in height. 188 Dismantling and Refixing of outdoor units of Split ACs with necessary drillings wherever required and the outdoor unit will be fixedon wall with proper fixing with supporting stand arrangements along with fasteners including connecting up copper pipe, nitrile insulation for copper pipe, bracing, control cable and PVC drain pipe, gas charging and testing and commissioning AERB guidelines (Note : Copper pipe, nitrile insulation for copper pipe and gas shall be measured and paid seperately under relevent schedule of items) 189 Supply only copper tubing for refrigerant suction line of Split AC of size 19.05 mm drawn through pipes/ fixed to walls/ laid on floor or roof complete all as specified and directed. 190 Supply only copper tubing for refrigerant discharge line of Split AC of size 9.5 mm drawn through pipes/ fixed to walls/ laid on floor or roof complete all as specified and directed. 191 M&L for copperwiring control cable of 2.5 sqmm 5 core from outdoor to indoor unit complete all as specified and directed. 192 Supply of refrigerant gas, R32 Suitable for cooling equipments suppiled and filled complete all as specified and directed. 193 Supply of refrigerant gas, R22 Suitable for cooling equipments suppiled and filled complete all as specified and directed. 194 Supply of heat insulation superior quality nitrile rubber of 13 mm thickness, ISI marked for copper tubing suitable for refrigerant suction line including necessary clamps, PVC tape knots in all respects complete all as specified and directed. 195 Supply of heat insulation superior quality nitrile rubber of 9 mm thickness, ISI marked for copper tubing suitable for refrigerant suction line including necessary clamps,PVC tape knots in all respects complete all as specified and directed. 196 Supply of AC drain hose outlet PVC pipe of size 20 mm complete all as specified and directed. 197 Supply of one outdoor unit stand suitable for split ac of capacity 1.5 ton along with fasteners and necessary connected items for installation of outdoor unit on to the wall complete all as specified and directed. 198 S&F for fixing of Earth continuity conductor of size 20X3 mm copper strip fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles including drilling holes in walls wherever necessary complete all as specified and directed. 199 S&F Earth continuity conductor of size 25X4 mm copper strip fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles including drilling holes in walls wherever necessary complete all as specified and directed. 200 M&L for Earthing complete with galvanised steel earth electrode plate of size 600x600x6.3 mm thick, buried directly in ground(earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.50m below normal ground level, connected to galvanised iron strip of size 25X4 mm as earth lead up to test point with suitable size GI nuts/bolts, washers,check nut and brazed properly up to main board,LT panel etc and adequate quantity of charcoal and salt 15 cm around the earth plate including earth pit in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregates,40mm thick precast RCC cover in 1:2:4 reinforced with 8mm dia TMT bars 3 Nos both way including CI cover 10 mm thick with hingedand frame of angle iron 25x25x6mmwith 6mm dia MS bar handle made to shape, excavation and earth work in any type of soil and including medium grade GI watering pipe 20mm bore with funnel and wire mesh and medium grade GIprotection pipe 40mm bore up to main board complete all as shown in electrical plate no 3 of MES schedule Part-I , connected to earthing testing point and testing on completion complete all as specified and directed.Note:s (i) The unit rate shall includes 40 mm dia GI pipe up to 7.5m for protection of earth lead. (ii) The unit rateshall includes GI main earthing lead/strip of size 32x6 mm from earth electrode to test point up to 7.5 meter (iii) In case measured value of earth resistance of each earthingis recorded more than 3 ohms then the earthing shall be re done by the contractor without any extra cost to the department. 201 ITEMS APPLICABLE FOR JOB G 202 S&F 20 mm bore GI tubing med grade galvanished with all ftgs and fixed complete to walls & floors complete all as specified and directed. 203 S&F 25 mm bore GI tubing med grade galvanished with all ftgs and fixed complete to walls & floors complete all as specified and directed. 204 S&F 1000 ltrs capacity potential moulded polyethylene water storage tank (cylindrical or vertical) hoisted and fixed in position complete all as specified and directed. 205 S&F 25 mm bore Ball brass valves,high pressure,with polythene float and flynut complete,screwed for iron pipe or brass ferrule and fixed all as specified and complete all as specified and directed. 206 S&F 15 mm bore fancy type, chromium platedStop valves / Angle cock screwed down high pressure with crutchhandle screwed both ends for iron pipe or for unionscomplete all as specified and as directed.
