Tender For Comprehensive Repair To Certain Otm Bldgs Of Adsr, Asc Bn And Guards Under Age B/R I At Patiala Mil Stn; 2 Taking down cement plaster of any description, any thickness from external surfaces of walls/soffits etc. incl raking out joints, hacking for keys, scrubbibg down with water etc complete all as specified and directed by Engineer-in-Charge. 3 Material & labour for cement plastering 15mm thick in two layers (10mm and 5mm respectively) in cemet mortar 1:4 including mixing of liquid water proofing compound as per manufacturers instructions on brick work or concrete surfaces or in chajjas/parapet walls etc finished even and smooth without using extra cement and fixing of chicken wire gauge where directed complete all as specified and as directed by Engineer-in-Charge. Note : WPC and chicken wire gauge will be measured and paid separately. 4 Supply only integral liquid water proofing compound complete all as specified & as directed by Engineer-in-Charge. Make : Pidilite/Sika 5 Material & labour for cement plastering 10mm thick in cemet mortar 1:6 on brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. 6 Material & labour for cement plastering 10mm thick in cemet mortar 1:3 as on ceilings or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. 7 Material & labour for Applying two coats of oil bound distamper white or tinted over a coat ofprimer on walls incl preparation of plastered surfaces of wall complete all as specified and directed by Engineer-in-Charge. 8 Material & Labour for applying Two coats of 100% wheather proof paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. 9 Material & labour for preparation ofplastered surfaces of ceiling and applying three coats of white wash including preparation of surface, complete all as specified and directed by Engineer-in-Charge. 10 Material & labour for preparation of newely steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified 11 Material & labour for Preparation of newly wooden surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified 12 Material & labour for Repair to RCC sunshades, Chajjas, Balconies, Columns, bands, beams and similar RCC work at any position/height by dismantling loose/disintegrated portion and dubbing out with Cement Concrete 1:1½:3, 15mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished to required shape including provision of necessary supports if required and stitching of cracks with mild steel U clamps made out of 8mm dia @ 150mm c/c with inserting concrete block stretcherwith cement mortar 1:3 mixed with adhesive chemical (Polymer based) and reinforced with PVC chicken mesh including form work where ever required and finished with10 mm thick plastering in CM 1:4 finished even and fair without using extra cement including preparation of surfaces to receive finishes complete all as specified and directed. 13 Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins,arches,pillars etc complete all as specified. 14 Material & labour for Brick work with sub class B bricks straight or curved on plan exceeding 6m mean radius bulit in C:M 1:6 all as specified. 15 Material & labour for Brick work in cement mortar 1:4 complete all as specified and directed. 16 Roughening the surfaces of old concrete floor by picking, sweeping, cleaning and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and directed 17 Dismantling, floor, hearth or wall tiling including CM(bedding (but not backing), removing serviceable tiles to store & rubbish off the premises 18 M & L for Non - skid coloured Ceramic tiles 7-8 mm thick (square/ rectangular) area of Each tile exceeding 0.18sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cementslurry@ 3kg per SQM and pointed in white or coloured cement to match, incl 15 mm thick screed bed in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge. 19 All as per Srl Item No 17 above, but as in skirting 100mm height laid over 10mm thick rendering coat in CM 1:4 set and jointed in neat cement slurry and pointed with white or coloured cement to match, complete all as specified and directed by Engineer-in-Charge. 20 M&L coloured glazed ceramic tiles size 450x350x7mm thick laid over 10mm thick rendering coat in CM 1:4, set and jointed in neat cement and pointed in white or coloured cement to match.The dado of same finish as of flooring shall be flush with plaster & all edges properly mitered complete all as specified and directed by Engineer-in-Charge. 21 M&L for7 to 8mm thick Non skid joint free coloured ceramic tiles area of each tiles exc 0.11 Sqm but n.exc 0.18 Sqm laid over 15mm thick bedding layer in CM 1:6, set and jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified and directed by Engineer-in-Charge. 22 Material & labour for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations with pigment to match the shade of slab including rubbing, cutting and mirror type granite polishing complete all as specified and directed by Engineer in charge. 23 Demolition of stone slab and tiles of any description or thickness as in floors, apron etc laid, bedded and pointe in any mortar complete all as directed. 24 M&L for Baroda Green marble,machine cut as in shelves/steps/cills/jambs/skirting/border only in tile flooring and the like works and flooring etc,15 to 18mm thick including bull nose the front length,set and jointed in cement slurry over & including screed of 15mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing,cutting and mirror type granite polishing complete all as specified.Note: Single piece should be used in steps/cills/jambs/shelves. 25 Material & labour for machine cut Kota stone slab flooring 18-20 mm thicklaid over 15 mm thick cement mortar 1:4 screed bed laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab including rubbing and polishing to mirror finish complete to be fixed in any position as described and specified. 26 Material and labour for coloured tiles 10 mm thick as in skirting to match the shade of kota stone flooring laid over screed bed 1:3 and jointed with white cement and pigments to match the shade complete all as specified and directed. 27 M & L for 18- 20mm thick granite (of any type) work (table rubbed and polished) in steps, Jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 20 mm thick cement plaster (1:3) complete all as specified. 28 Supply & fixing stainlessHarrison rails 25mm dia mild steel, chromium plated with fixing brackets,finials (02 Nos for each curtain rod), rollers etc for curtain rod incl all fixing complete all as specified and directed by Engineer-in-Charge. 29 Taking down chokhats or frames (without taking off shutters from the frame) n.exc 1.50 sqm including cutting holes and making good reqd shape for hold fast block for new frame complete all as specified directed. 30 S & F factory made PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling& fixing in opening complete all as per specification & drawing.(Note:- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life), Complete all as specified 31 Supply & fixing factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:),( brown/ coffe colour)with homogeneous fine cellular structure having density of 550 KG/Cumwith 2,4 or 6 raised panel design with 5mm thick Moulded PVC Sheet on the front Face & 2mm Plan colour PVC sheet on back face, supplying & fixing in frame at site as per specification. 32 Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holesand making good reqd shape for hold fast block for new frame complete all as specified. 33 Taking down shutter not exc 2 sqm each of any description complete all as specified and directed. 34 Supply & fixing factory made Pressed steel frames made of MS sheet of 1.20 mm thickness for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc,size 125x60mm complete as specified and directed. 35 S&F factory made Pressed steel frames made of MS sheet of 1.20 mm thickness for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etccomplete all as specified,size 105x60mm complete as specified and directed. 36 M&L for Plain cement concrete (1:3:6) type C-0,using 12.5 mm graded crushed stone aggregate as in back filling of pressed steel frame /hold fast blocks etc and similar complete all as specified and directed by Engineer-in-Charge. 37 Supply & fixing factory made flush shutters 35mm thick, 7 Ply,solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. 38 M&L for 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Pt-1 section 8 clause 8.24(a) supplied and fitted to chowkhats complete all as specified and directed. 39 M&L for Butt hinges 100 mm size, cast brass with mild steel butt hinge pin, bright polished and fixed, type B-11 complete all as specified and directed. 40 Supply & Fixing Aluminium handles125mm, cast type, anodised complete all as specified and directed. 41 M&L for Aluminium alloy, anodised, sliding door bolt 250 mm length with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy and fixed complete all as specified and directed 42 M&L for Aluminium anodised, barrel tower bolts of 200 mm size of extruded section and fixed complete all as specified and directed. 43 Supply & fixing 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate including necessary welding to chowklhats complete fixed all as specified 44 M&L for Floor door stopper of size 140 mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring,fixed in floor complete all as specified and directed. 45 Supply & fixing factory made Steel window box type usning ERW hollow P section comprising double frame for and including gauged and glazed Skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs, etc including 8mm square gaurd bars all as shown on drawing No TD-191 (R) sheet 1/4 to 4/4 complete all as specified and directed by Engr-in-charge 46 Supply & fixing Steel ventilator with top hung shutter including hinges, steel peg stay complete complete all as specified and directed by Engr-in-charge 47 S & F Mild Steel Framed work such as Guard Bar/grill for steel ventilator welded to ventilator frame or fixed independantly, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified & directed by Engineer-in-Charge. 48 Supply & fixing for 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane 49 Supply & fixingfor 3 mm figured glass sheet ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in Each pane complete all as specified. 50 Supply & fixing for Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplescomplete all as specified and directed by Engineer-in-Charge. 51 S&F in repairs vitreous china wash basin, white, flat back, size550x400m excluding taps, waste , chain & plug & porcelain stopperincluding brackets incl cutting for pinning in ends of bracketes or erecting standand fixing and supply and waste pipe complete all as specified and directed 52 S&F in repair vitreous china squatting pan Orissa pattern size 580x440mm white with integral foot rest complete incl provision of lime concrete bedding complete all as specified and directed. 53 S & F as in repairsvitreous china wash down water closet European Type pedestal pattern with seat & cover as in repairs with jet spray complete incl fixing of flush pipe etc complete all as specified and directed. 54 Supply & Fixed in repair for vitreous China bowl urinals (back or cornerwall type) complete including providing & fixing plugs bedding urinal against wall in cement mortar 1:2,securing urinals to plugs with &including 60mm long brass screw ,pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe and waste pipe,(Ist quality) with flat back of size 465x355x265mm white with grating and unions for discharge pipe complete all as directed. 55 S&F in repair 10 ltr capacity PVC flushing cistern low level white colour incl PVC connection PVC flush pipe of reqd length complete all as specified and directed. 56 S&F in repairs 600mm x 450 mm bevelled edge mirrorof selected quality, mounted on 6 mm thick AC plain building board or commercial plywood and fixed to wall on wooden plugs with chromium plated brass screws and cup washers all complete as specified and as directed. 57 Taking up or down GI tubing 15mm bore pipe and connection including cleaning for refixing or removal from site as directed 58 Supplying and laying of 15 mm dia Tubes, medium grade,galvanised,with all fittings on walls/ceiling or laying in floors complete all as specified & directed 59 Taking up or down GI tubing 20mm bore pipe and connection including cleaning for refixing or removal from site as directed 60 S&F 20mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall etc complete all as specified and as directed. 61 Supply & fixing in repair overhead shower 125mm size with 235mm long shower arm and incl all necessary accessories as recommended by manufacturer for fixing and taking down existing of any description/size complete in all respect all as specified. 62 Supply & fixing in repair towel rail 20mm dia,D type, 60 cm long between flanges and including all accessories like brackets/screws etc as recommended by manufacturer and complete fixed in position complete all as specified. 63 Supply & fixing in repair Bib taps,CP,fency type long body with wall flange screwed for 15mm bore of iron pipe or for brass ferrule and fixed in position complete in all respect all as specified. 64 Supply & fixing in repair Pillar taps, fency type, long neck, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for 15mm bore of iron pipe and fixed in repairs all as specified. 65 Supply & fixing in repair Stop valves, fancy type, CP with long shank and cup ( concealed type ), exposed part kit with wall flange and regular body of concealed stop cock suitable for 15mm line with protection cap fixed in position complete in all respect all as specified. 66 Supply & fixing in repair Angular Stop Cock with wall flange, fency type chromium plated cast copper alloy screwed down, high pressure, screwed one ends for 15mm bore of iron pipe or for union and fixed in position complete in all respect all as specified. 67 S&F in repair stainless steel grating 150x150 mm size square shaped with cockroach trap for floor trap fixed in position complete all as specified . 68 S&F in repair towel ring of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) 69 S&F acrylic glass shelf assembly for soapdish and appropriate space for placing other things like tooth brushes comb tooth paste etc and fiexed to walls with plug and brass chromium plated screws complete all as specified and directed 70 Dismantling water tanks and removing to store of capacity exc 250 & n.exc 500 ltrs. 71 S&F tripple layered rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top / cover) white coloured 500 Ltrs capacity hoisted and fixed in position all as specified including ball brass valves, high pressure, with polythene float and fly nut complete screwed for 20mm bore iron pipe and including GI nipple/union of 20mm bore to connect GI tubing to PVC tank complete all as specified and directed. 72 Dismantling water tanks and removing to store of capacity exc 500 & n.exc 1000 ltrs. 73 S&F tripple layered rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top / cover) white colourd 1000 Ltrs capacity hoisted and fixed in position all as specified including ball brass valves, high pressure, with polythene float and fly nut complete screwed for 20mm bore iron pipe and including GI nipple/union of 20mm bore to connect GI tubing to PVC tank complete all as specified and directed. 74 S & F 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed in repair (Minimum weight 20 mm - 210 g m s .) all as specified &directed. 75 S&F in repair 15mm dia Bib tap standard of PTMT fancy type any colour high pressure screwed for iron pipe and fixed white coloured (Minimum weight 15mm-90gms/20mm-125gms) complete all as specified and directed. 76 Supply & fixing 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair complete all as specified. 77 M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggretgate, as in base for PVC tanks,as in base of floors and other similar items complete all as specified and directed. 78 Supply & fixing PVC connections 15mm size with brass nuts of length 450mm complete all asspecified and directed. 79 Dismantling of cast iron/pvc soil waste & vent pipes of any dia mm dia incl all fittings etc complete. 80 S&F Cast iron soil, waste and vent pipe, 100mm bore, sand castin any length, with or without ears, with cement joints,fixed to walls with and including stack clamps of size 25X3mm FI, nuts , bolts etc. and making necessary connections complete all as specified and directed. 81 S&F Cast iron soil, waste and vent pipe, 100mm bore, sand castin any length, with or without ears, with cement joints,laid in trenches or in floors complete all as specifiedand directed. 82 S&F Cast iron soil, waste and vent pipe, 75mm bore, sand castin any length, with or without ears, with cement joints,laid in trenches or in floors complete all as specifiedand directed. 83 Supply and fixing 100 mm Cast iron Traps ‘P’ or ‘S’ , 600mm long,complete all as specified and directed. 84 Supply & fixing for cast iron branch pieces singleCentrifugal type (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, suitable for 100 mm bore pipe, fitted with oval access doorjointed with lead joint, complete all as specified. 85 Supply & fixing for CI CowlCentrifugal type suitable for 100 mm bore pipe as in repair, complete all as specified. 86 Supply & fixing for Cast iron bends/Tee duck foot or heel rest, radiusfor 75 mm bore pipe, complete all as specified and directed. 87 Supply & fixing for Cast iron bends/Tee duck foot or heel rest, radiusfor 100 mm bore pipe, complete all as specified and directed. 88 Supply & fixing for PVC(HDPE) rain water pipes, 150 mm bore, single socketed in any length with rubber ring joints fixed to walls complete all as specified including fixing of pipe to wall with flat iron clamps of size 25 x 3mm, bolts washing, nuts etc includingtaking down existing damaged CI rain water pipe complete all as specified and as directed 89 Supply & fixing PVC (SWR) bends/tees of any radius for 150mm bore as in repair complete all as specified. 90 Supply & fixing Salt-glazed stoneware gully traps,Centrifugal type 150x150mm size,square or round mouthed, type P or S incl CI grating fixed in repair complete all as directed and specified. 91 Supply & fixing Cast iron floor trap 110mm dia and 600mm long including jointing with solvent cement in repair complete all as specified and directed by Engineer-in-Charge. 92 S&F 50 mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall for spout etc complete including taking down old pipe complete all as specified and as directed. 93 Dismantling of brick tiles or terracing tiles single layers on roofs complete all as specified and directed by Engineer-in-Charge. 94 Demolition of mud phuska on roof any thickness complete all as specified and directed by Engineer-in-Charge. 95 Material & labour for Roughening surfaces of old concrete floor/roof by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed by Engineer-in-Charge. 96 Material & labour for Cutting grooves in brick wall, 50mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed by Engineer-in-Charge. 97 Material & labour for PCC 1:3:6, type C-1 using 20mm graded stone agg as in padding over roof, minimum thickness at khurra as 25mm to maintain a slope of 1:100 complete all as specified and directed by Engineer-in-Charge. 98 Material & labour for Providing and laying3mm thick APP (Atactic Polyproplene Polymer) APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid over and including bitumen primer @ 0.30 kg / sqm by forced application complete all as specified and directed by Engineer-in-Charge.. 99 Material & labour for 20- 22 mm Precast PCC plain factory made tiles,ISI marked,22 mm thick, of size 250 mm x 250 mm, machine pressed and cut polished and set jointed and pointed in neat cement slurry andfabricated using grey cement & no pigments. over and including 15 mm thick cement mortar (1:3) bedding and joints grouted flush in cement mortar (1:3) mixed with integral liquid water proofing compound over roof surfaces complete all as specified and directed by Engineer-in-Charge. 100 Supplying and applying two component elastomeric acrylic polymer modified cementitious waterproofing coating, SmartCare Damp Block 2K or approved equivalent, having 100%elongation as per ASTM D412, resisting 5 bars hyrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5. The coating shall have food grade certificate from laboratories like CFTRI. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc., complete as per manufacturer specifications.Product Make: Sikka/Fosroc/Dr Fixit 101 Supply and apply cementitious coating for corrosion protection having a cement base polymer modified rebar corrosion protection system by applying the first coat approx 1mm thick layer of product carbonation resistance 2mm of sikatop ArmatecR -108 or equivalent as specified corresponds to 20 mm of normal mortar;bond strength 1N/mm2 according to ASTM C 882-78 applying @ 4kg/m2 for two coats onto the prepared reinforcing steel with a medium-stiff brush.it is unavoidable that specified product will also be applied in the same way after a waiting time of 2-3 hours (+20C) complete all as per manufacturers instructions and all as specified. Product Make: Sikka/Fosroc/Dr FixitNote: (i) The application of cementitious coating for corrosion protection shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed. (ii) The applicator shall be got approved from GE before execution of this item. 102 Proving ,mixing & applying two components Epoxy resin concrete bonding coat on prepared RCC surfaces as per manufacturers apecification incl prepration of surface by chipping and throughly cleaning of surface complete wherever required and as per directions of Engineer-in-charge.Consumption: o.5 kg/m2 complete all as per manufacturers instructions and all as specified.Product requirements : complies with ASTM C 881 Type II Grade 2 class B+C. Product Make: Sikka/Fosroc/Dr FixitNote: (i) The application of epoxy bonding primer shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed.(ii) The applicator shall be got approved from GE before execution of this item. 103 Supply and apply a pre-batched one component polymer modifies cementitious patch repair mortar in 25mm thickness.Yield:approx 0.84 ltr/kg.System requirements:compressive strength =50 N/mm2 (28 days)according to ASTM C 109 : flexural strength = 3 N/mm2 (7 days)according to ASTM C 293-79consumption of 2.1 kg/sqm/mm Product Make: Sikka/Fosroc/Dr FixitNote: (i)The applicator of polymer repair mortar shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed.(ii) The applicator shall be got approved from GE before execution of this item. 104 Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. 105 Dismantling timber scantlings 40 sq. cm and over in section, in unframed work in any position 106 M&L for providing and fixing steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubescomplete all as specified and as directed. 107 Dismantling asbestos cement (corrugated, semicorrugated, etc. sheets in roof coveringscomplete all as specified and as directed. 108 S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified as specified as specified 109 S&F sinks with drainage board made of stainless steel01 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm fixed in repair complete all as specified and as directed. 110 S&F as in repairs stainless steel plate rack of size 30x24x10 size as per trade pattern fabricated with 0.50mm thick stainless steel sheet suitable for stacking 15 plates with hooks /fittings complete all as per sample kept in Engr-in-charge office( wt shall not be less than 4 kg) 111 S&F MS chromium plated peg set of five fixing with wallcomplete all as specified and as directed. 112 Demolition of cement concreteun-reinforced in ground floors and pavings n.exc 15cm thicknesscomplete all as specified. 113 Material and labour for carrying out water proofing treatment of sunken floor complete all as specified under:(i) The concrete/wall surface shall be cleared thoroughly of all laitance,loose particles,dust,grease etc and any friable and unsound area which shall be chipped,cleaned and thereafter pre-wetted to a satured surface dried condition. (ii) In case of pot holes/superficial cracks,the same shall be repaired with polymer modified mortar using URP as admixture @ 10% of cement content. (iii) The polymer modified mortarusing URP as admixture @10% of cement content shall also be applied on vertical surfaces after removing of plaster upto 60 cm height.(iv) The surface thus prepared shall be coated by applying 2 coats of Dr Fixit Hydrochem super in the sunken areas and extending it upto 150 mm above the finished floor level.This includes layer of a 150 mm wide strip of an open woven glass fiber mesh over the PCC benching (Gole) on the 1st coat whille it is still wet.(v) Rendering 15 mm in CM 1:4 admixed with integral water proofing compound@ 200 ml per bagof cement complete all as specified and directed by the Engineer-in-Charge. 114 M & L for plain cement concrete 1:7:12 mix, type F-2 (using 40mm graded Brick aggregate) as in filling of sunken portion complete all as specified and directed. 115 Material & labour for PCC 1:2:4, type B-0 using 12.5mm graded stone agg as in roof kerb, benching, mud stops, steps, coping and the like items slightly rounded or chamfered on the edges complete all as specified and directed by Engineer-in-Charge. 116 Material & labour for Cement concrete (1:3:6) type C-2 using 20mm graded stone aggregate as in plinth protection/ floor finish, 50 mm thick, surfaces finished even and smooth without using extra cement as in plinth protection including provision of construction joints complete all as specified and directed by Engineer-in-Charge. 117 M&L for 75mm thick PCC 1:3:6 of type C-2 using 40mm graded stone agrregate as in sub base of floors etc complete all as specified and directed. 118 M7L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. 119 M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. 120 S& F in repair stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 121 Supply and fixing 3mm thick sheet glass in repair incl taking out old glass panes complete all as spcified and directed. 122 Taking down carefully existing points wiring on surface conduit/concealed conduit forlight/ fan/socket /power/bell from wall & roof along with fitting and fixtures such as switches, sockets, ceiling roses, batten holders, unserviceable light fittings, piece of wires,gutties, conduit, wooden boards etc and making good the disturbed portion ofwalls, ceiling etc all as specified and directed Engr-in-charge. 123 M & L for Point wiring with 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper conductor for one light/fan in new PVC conduit to be terminated in pressed steel terminal boxes with top cover plateincluding 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper earth continuity conductor connected to cmmon earth dolly controlled by one switch and/or one regulator complete including repairing the surfaces in CM 1:3 and finishing the surface as per existing treatment all as specified and directedby Engineer in-charge Note-I-(Switches and regulators shall be measured and paid for separately). Note-II- ( Wiring shall be done as per colour code in IS for phase, neutral and earth). Note-III- (The cost of modular cover plate, blank plate and metal flush boxes is deemed to be included in the unit rate quoted for this item).Note -IV - cost of Eye/bottle thimblesused for connection in switches/sockets & MCBs in DBs is deemed to be included in the unit rate quoted for this item. Note:- V- Rate of cutting chasing included in the unit rate quoted for this item 124 M & L for point wiring with 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper conductor for one light point controlled by 2 way and including PVC rigid concealed conduit medium grade 19/20 mm dia to be terminated in pressed steel terminal boxes with top cover plateincluding 1.5 sqmmPVC insulated and unsheathed FRLSH single core multi-stranded copper earth continuity conductor connected to cmmon earth dollycontrolled by one switch and/or one regulator complete including repairing the surfaces in CM 1:3 and finishing the surface as per existing treatment all as specified and directed.Note-I- ( Wiring shall be done as per colour code in IS for phase, neutral and earth). Note-II- (The cost of modular cover plate, blank plate and metal flush boxes is deemed to be included in the unit rate quoted for this item). Note -III - cost of Eye/bottle thimblesused for connection for 2 way switch is deemed to be included in the unit rate quoted for this item. Note:-III- Rate of cutting chasing included in the unit rate quoted for this item 125 All as per Sl item No 122.00 above herein before but one socket out let 5 pins 5 Amp on the same board with other switches complete all as specified and directed. 126 All as per Sl item No 122.00 above herein before but for one socket out let 5 pins 5 Amp on independent board complete all as specified and directed. 127 All as per item No.122.00 herein beforebut 2.5 Sqmm PVC insulated and unsheathed FRLSH single core multistranded copper conductor incl 2.5 Sqmm PVC insulated and unsheathed FRLSH single core muilti-stranded copperearth wire for switch socket combination 3 pin 15 amps on independent board. 128 M & L for Point wiring with 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper conductor for one light/fan in existing conduit to be terminated in pressed steel terminal boxes with top cover plateincluding 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper earth continuity conductor connected to cmmon earth dollycontrolled by one switch and/or one regulator complete including repairing the surfaces in CM 1:3 and finishing the surface as per existing treatment all as specified and directedby Engineer iin-charge Note-I-(Switches and regulators shall be measured and paid for separately). Note-II- ( Wiring shall be done as per colour code in IS for phase, neutral and earth). Note-III- (The cost ofmodular cover plate and metal flush boxes is deemed to be included in the unit rate quoted for this item). Note -IV - cost of Eye/bottle thimblesused for connection in switches/sockets & MCBs in DBs is deemed to be included in the unit rate quoted for this item. 129 All as per Sl item No 127.00 above herein before but one socket out let 5 pins 5 Amp on the same board with other switches complete all as specified and directed. 130 All as per Sl item No 127.00 above herein before but for one socket out let 5 pins 5 Amp on independent board complete all as specified and directed. 131 All as per item No 127.00 herein beforebut 2.5 Sqmm PVC insulated and unsheathed FRLSH single core multistranded copper conductor incl 2.5 Sqmm PVC insulated and unsheathed FRLSH single core muilti-strandedcopper earth wire for switch socket combination 3 pin 15 amps on independent board. 132 Supply and fix in replacement of Modularswitch1 way, 6 Amps, 1 module complete all as specified and directed by Engr-in-charge. 133 Supply and fix in replacement of Modularswitch1 way, 16 Amps, 1 module complete all as specified and directed by Engr-in-charge. 134 Supply and fix in replacement of Modularswitch2 way, 6 Amps, 1 module complete all as specified and directed. 135 Supply and fix in replacement of ModularBell switch1 way, 6 Amps, 1 module complete all as specified.and directed by Engr-in-charge. 136 S & F Bell ding dong electronic complete all as specified and directed by Engineer-in-charge. 137 Supply and fix in replacement of Modular socket 5 pin 6 Amps, 2 module complete all as specified and directed by Engr-in-charge. 138 Supply and fix in replacement of Modularsocket 5 pin 6/16 Amps, combination type2 module complete all as specified and directed by Engr-in-charge. 139 Supply and fix in replacement of Fan regulator modular type 2 module complete all as specified and directed by Engr-in-charge. 140 Ceiling rose surface bakelite surface 65 x 50mm3 terminals all as specified & directed by Engr-in-charge. 141 Material and labour for in replacement angular typelamp holder, PVC/ polycarbonate type with back plate suitable for 7 to 23 watts for batten fitting, including plastic square board of required size, complete all as specified and directed. 142 S&F 9 wattLED Bulb with base cap B22/E27 type minimum 90 lumen/watt having correleted color temperature(CCT) of Emitting light 6500 /3000 K with CRI of LED >90complete all as specified and directed. 143 Supply and fix in replacement of New generation energy saving and environmental friendly long life LED building security light 1x25 watts made up of pressure die cast alluminium housing with high power LED as light source and lense embedded PC cover having TOP OPENING separate driver compartment with IP66 protection and impact resistance of IK07,with all accessories including suitable bracket with 32 mm bore light grade GI pipe bend to shape, including MS clamp of size of required size and PVC cable 1.5 Sqmm twin core from ceiling rose to light fittings complete all as specified and directed by Engineer-in-charge. 144 Supply and fix in replacement of Recess mounted LED luminaire 36 watt 3600K-6300Ksuitable for gridd celling cutout dimensions: 2x2 Ft. incl connecting with twin core copper wire from ceiling rose to fitting, Fixture size: (LxWxH) in (595x595x65) mm incl lamp and driver all as specified & directed. 145 Supply and fix in replacement of Recess mounted LED luminaire 36 watt warm white 3000K suitable for gridd celling cutout dimensions: 2x2 Ft. incl connecting with twin core copper wire from ceiling rose to fitting, Fixture size: (LxWxH) in (595x595x65) mm incl lamp and driver all as specified & directed. 146 Supply and fixing LED flat panel 2 x 2 ft size fully diffused surface mounted fitting (grid/gypsum type) 36-40 watt, 5700 K warm/cool white with powder coating and CRCA front cover incuding frame with provision of PVC flexible copper conductor cable from ceiling rose to light fittings as in repair complete all as specified and directed by Engr-in-charge. 147 S&F Ceiling/surface mounted Slim design LEDsquareDownlight with Superior light output and internal driver 18/20 Watts 230 volts with internally pre-wired and including connecting up with two core twisted flexible copper conductor cable with suitable size compelte all as specified and directed by Engineer-in-Charge. 148 S & F in replacement of new generation energy saving and environmental friendly long life industrial 80 Watt LED High Bay luminaries with clear PC diffuser powder coated Aluminium body IP 65 mounting with eye bolt and PVC cable 1.5 Sqmm twin core from ceiling rose to light fittings complete all as specified and directed. Make: crompton/Havells/Philips/bajaj 149 Supply and fix in replacement of Surface Mounted LED Bulk Head Luminaire of capacity 10 watt with ABS Body & Polycarbonate Diffuser, IP54 inc connection with ,with flexible wire 0.5 sqmm copper cable all as specified & directed by Engr-in-charge. 150 M & L for Sub main wiring with two single core 6.0 Sqmm PVC insulated and unsheathed FRLSH,stranded copper conductor cable drawn through PVC concealed conduit 25 mm dia including 6.0 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note 1:- 2(two) Runs of 6.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Run of 6.00 Sqmm Copper conductor Earth wire shall be measured as one unit)Note 2 :(i) Rate quoted for this items shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of 25 mm dia with tees, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.(ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces and cutting not exc.10 cm girth . (iii) Including taking out/down existing unserviceable sub main wiring (iv) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. 151 M & L for Sub main wiring with two single core 4.0 Sqmm PVC insulated and unsheathed FRLSH,stranded copper conductor cable drawn through PVC concealed conduit 25 mm dia including 4.0 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note 1:- 2 Runsof 4.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Runof 4.0 Sqmm Copper conductor Earth wire shall be measured as one unit)Note2 : Rate quoted for this items shall be inclusive of the cost of(i) Rigid non-metallic PVC conduit of 25 mm dia withtees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.(ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces, cutting not exc.10 cm girth . (iii) Taking out/down existing unserviceable sub main wiring.(iv) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. 152 M & L for Sub main wiring with two single core 10.0 Sqmm PVC insulated and unsheathed FRLSH,stranded copper conductor cable drawn through PVC concealed conduit 25 mm dia including 6 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note 1:- 2 Runsof 10.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Runof 6.00 Sqmm Copper conductor Earth wire shall be measured as one unit)Note2 : Rate quoted for this items shall be inclusive of the cost of(i) Rigid non-metallic PVC conduit of 25 mm dia withtees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.(ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces, cutting not exc.10 cm girth . (iii) Taking out/down existing unserviceable sub main wiring.(iv) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. 153 M & L for Sub main wiring with 04 (Four) single core 10.0 Sqmm PVC insulated and unsheathed FRLSH,stranded copper conductor cable drawn throughpvc concealed conduit of suitable dia including 6.0 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note1:- 4 Runsof 10.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Runof 6.00 Sqmm Copper conductor Earth wire shall be measured as one unit)Note2 : Rate quoted for this item shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of suitable size dia with tees, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.(ii) Cutting chases, pinning in and making good to facing where requiredpointing in cement mortar 1:3 to match theexisting surfaces and cutting not exc. 10 cm girth. (iii) Taking down/out existing unserviceable sub main wiring.(iv) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. 154 Supply and fix in replacement ofMCCB, 4 Pole, 100 A, 25 KA for fixing in DB including proper thimble connection, thermal and magnetic release protectioncomplete all as specified and directed by Engineer-in-charge. 155 Supply and fix in replacement of MCCB, 4 Pole, 63 A, 16 KA for fixing in DB including proper thimble connection, thermal and magnetic release protectioncomplete all as specified and directed by Engineer-in-charge. 156 Supply and fix in replacement epoxy power coated MCCB distribution distribution box double door VTPN 4 way vertical type AC 415 V with IP 43 protection for MCBs alongwith provision of MCCB as incomer with common bus-bar rated 200 Amp at incoming end of outgoing MCBs grouted/ flush to wall, complete all as specified by Engineer-in-charge. (Note :- MCCB will be measured and paid under seperate item) (i) Cost of Eye/bottle thimblesused for connection in switches/sockets & MCBs in DBs shall deemed to be included in unit rate quoted for this items, (ii) Electric wiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth (iii) Connection of cable with VTPN shall be done through appropriate size of thimble. 157 Supply and fix in replacement of MCB, single pole & neutral (SPN) 10 KA 240 volts, 63 Amp capacity fixing in DB’s complete all as specified and directed. (Note: MCB should be C curve as directed by engineer in charge) 158 Supply and fix in replacement of Sheet metal enclosure 8 ways double door for DBs when MCBs areto be used 240,volts including 200 Amps standard bus bar of suitable size and common neutral link allflush mounting type, drilling holes for incoming and out going cables with IP43 protection complete all as specified & directed byEngr-in-charge. 159 Supply and fix in replacement of Sheet metal enclosure 4 ways double door for DBs when MCBs areto be used 240,volts including 200 Amps standard bus bar of suitable size and common neutral link allflush mounting type, drilling holes for incoming and out going cables with IP43 protection complete all as specified & directed byEngr-in-charge. 160 Supply and fix in replacement of Sheet metal enclosure 12 ways double door for DBs when MCBs areto be used 240,volts including 200 Amps standard bus bar of suitable size and common neutral link allflush mounting type, drilling holes for incoming and out going cables with IP43 protection complete all as specified & directed byEngr-in-charge. 161 S & F in replacement of MCB , SPN,240 Volts ,32-40 amp for fixing in DBs ofincluding proper thimble connections complete all as specified and directed by Engineer-in-Charge. (Note: MCB should be B or C curve as directed by engineer in charge) 162 S & F in replacement of MCB, TRIPLE pole & neutral (TPN) 10 KA 240 volts 40 to 63 Amp capacity fixing in DB’s complete all as specified and directed. (Note: MCB should be C curve as directed by engineer in charge) 163 S & F in replacement ofMCB, single pole 240 volts 6 to 32 Amp capacity for fixing in DB’s including proper thimble connections complete all as specified and directed by Engineer-in-Charge. (Note: MCB should be C curve as directed by engineer in charge) 164 S & F in replacement of Sheet metal enclosureDB TPN 4 ways double door 415 volts with 200 Amps standard bus bar of suitable size and common neutral link flush mounting type, drilling holes for incoming and out going cables complete with IP-43 protection complete all as specified and directedby Engr-in-charge 165 M & L for replacement of UNSV Earthing complete with galvanised steel earth plate electrode, 600x600 x 6.0mm thick burieddirectly in ground(earthpit not less than 2.25m deep below normal level) connectedtogalvanised earth leadwire 4.0mm dia by means of nuts, bolts, &washers of GI as shownin electrical plate No 3 of SSR PartI.Connected to earthing test pointtesting complete including necessary earth pit chamber PCC 1: 3: 6 type C1, and 50mm thick RCC 1 : 2: 4 chamber cover and with 8mm dia mild steel re-enforcement@ 15Cm C/C spacing both ways with a handle made of 8 mm bar for fitting, galvanised iron funnel, wire mash watering pipe GI 20 mm dia light grade, and protection to earth leadshall be providedwith GI pipe light grade 15mm dia up to 7.5m from the earth plate electrode, excavation including charcoal and common salt in alternative layers 15 cm Thick mixed refilling of soil etc complete all as directed by Engineer-in-charge. 166 Supply and fixingPVC gangbox 15 amp 1 switch and 1 socket 15 amp all as specified 167 Supply and fixing PVC gangbox 5 amp 2 switch and 2 socket 5 amp all as specified. 168 Supply and fixing PVC gangbox 5 amp 2 switch and 1 socket 5 amp all as specified. 169 Supply & fix in replacement of Tube light fitting Self Ballasted LED Batten. Extruded Thermoplastic body with PC Diffuser in squareLED Batten 18/20W 6500K cool /warm whiteof capacity ,20 watt,4 ft long incl 3 core flexible wire 0.5 sqmm copper cable all as specified and directed by Engr-in-charge. 170 Supply and fix in replacement of Tube light fitting Self Ballasted LED Batten. Extruded Thermoplastic body with PC Diffuser in squareLED Batten 10/12W 6500Kof capacity ,watt,2 ft long incl 3 core flexible wire 0.5 sqmm copper conductor cable all as specified and directed byEngr-in-charge. 171 M & L for Sub main wiring (with approved colour coding as per IS)with single core FRLSH PVC insulatedmultistranded copper conductor1.1 KV grade (main cable : number of runs indicated below) along with one run of single core FRLSH PVC insulatedmultistranded copper conductor 1.1 KV grade for earthing in and including PVC conduits of suitable size, for 2 runs of 1.5 sq. mm main cable + 1 run of 1.5 Sq. mm earth cable as in replacement of old unserviceable wiring complete all as specified and directed. Note:(i) Two different color wires shall be used for phase andneutral . (ii)Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) If Necessary cutting chasing shall be included in this item. 172 Supply and fix in replacement ofLED post top fitting 40 W powder coated aluminium die cast and spun aluminium with clear/diffused PC cover suitable for landscape lighting 240V, 50 Hz ,ACsupply complete with all accessories internally pre wired including provision of 3 corePVC flexible copper conductor from electric supply source to connector of light with degree of protection IP 65,CCT 6500K complete all as specified and directed by Engr-in-charge.Note: Cost of GI pipe of suitable dia of length 4 feet, grouting holes into piller and cement work has beenincluded in the rate quoted by contractor 173 Supply and fixin replacement of 12 watt LED light fitting decorative type wall mounting fixture including LED lamp compact and energy efficient epoxy powder coated luminaireand connecting with copper conductor flexible cable from ceiling rose to conector of the light complete all as specified and directed by Engr-in-charge. 174 Supply and fix in replacement ofLED post top fitting 20 W powder coated aluminium die cast and spun aluminium with clear/diffused PC cover suitable for landscape lighting 240V, 50 Hz ,ACsupply complete with all accessories internally pre wired including provision of 3 corePVC flexible copper conductor from electric supply source to connector of light with degree of protection IP 65,CCT 6500K complete all as specified and directed by Engr-in-charge.Note: Cost of GI pipe of suitable dia of length 4 feet, grouting holes into piller and cement work has beenincluded in the rate quoted by contractor 175 Supply and fix in replacement ofhighly reliable energy efficient multi high power LED with lensflood light designed with optimized optical performance and good heat dissipation with uniform distribution of capacity 80 Watt, CCT 5700-6500K, CRI>70, rated voltage 220V-240V AC, 50 Hz, Power factor>0.9, IP-66 dimension 290x235x155 mm epoxy powder coated pressure die casted aluminium housing with bright anodised aluminium reflectro and enclosed with heat resistant and toughened glass having constant current driver suitable for 140-280V AC working range suitable for facade lighting with all accessories internally pre wired including connecting with flexible copper conductor to connector of the light with necessary fixing arrangements complete all as specified and directed by Engr-in-charge. 176 Supply and fixing in replacement single pole and neutralenclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, complete all as specified and as directed by Engineer-in-charge. 177 Supply and fix new generation, energy saving, environment friendly, long life aesthetically designed aluminium landscape IP 65luminaire for diffused lighting with high power LED as light source LED Bollard pathway lightsof capacity 10 watt cool/warm white made up of aluminium pipe UV protected pure polyester powder coated having colour temperature(CCT) 3000K warm white fixed to concrete foundation by means of 3 nos M10 bolts complete all as specified and directed by Engr-in-charge.Note:- Cost of PCC foundation of suitable height , PVC conduit25 mm of suitable length, all electrical connection and all other items whichever required for fixing is deemed to be included in the unit rate quoted for this item. 178 Supply and fixincl taking down LED garden light fitting cool/warm white with LED bulb upto 20 watt E27/B22 base cap fitted on the piller with the help of GI pipe of suitable height and PCC up to suitable height nut bolts and in stainless steel housing with clear acrylic cover in top section with IP 65 protection class ,connection with 1.5 sqmm 3 core copper cableincluding making suitable PCCfoundation and all electrical connection complete all as directed. 179 Supply and fixing 1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connectionsone twin core cable flat or circular stranded conductor size of 6 Sqmm, twin core complete all as specified. 180 Supply and fix PVC insulated copper conductor 3 core 1.5 sqmm passing through flexible PVC conduit of 25mm dia and fixed with clamp complete all as specified and directed.Note:- Rate of Cable and flexible conduit both included in quoted rates.
