Tender For Carrying Balance Checklist Point For Electrical And Instrument Job; A Unloading, Handing, transportation from owners store, unpacking, visual inspection for completeness, damage, placement on foundation, leveling and alignment, associated civil works making good after placement, assembly including a loose items, erection, getting electricsi inspectors or local authoritys approval, dressing, cleaning, painting wherever required including supply of labour and materials as per drawing, instruction manual, relevant specifications and direction of engineer in charge shall be contractors responsibility. Supply of a few items specifically mentioned shall be in the scope of contractor. All the consumables like electrodes, fasteners, saddle for lighting cable laying and any other hardwares required to be supplied by the subcontractor. All Steel for mounting/frames are to be supplied by BandR Note: Cable termination and assocuted steel work for mounting/frames are covered under separate item of this SOOR. Installation, Testing and commissioning of following items Modification of existing 415V penel (in shut down) et 5536, providing cut out for relay mounting, necessary wiring changes, any other modification (hardware) etc. to be carried out to complete the job in totality is induded in CONTRACTOR scope a per approved drawing Feeder modification and Indisatur enstallation Feeder modification and Relay, estaliation 3 Patch cord installation and termination B Laying of cables of following sizes and ratings inside concrete Trenches, Buried trenches, duct bank, pull pit or cable support angles on Cable, Cable, fooing on platforms, jon bridge like structures (where quaritity cable does not call for use of cable trays) through pipes/Walls and protection pipes including unloading and transportation of cables from owners store to site, unpacking, visual inspection, dressing of cables, fixing of cables and cable tags on each terminating end. (Cable laid on horizontal nuh shall be tied by means of nylon cords whersas cable laid on structure/column and vertical run shall be suitably clamped by G saddle/clamps). Supply and erection of material, required for erection of pull pit, cable chember, cable joint chember, brick wall will be scope of contractor. Dust bank will be supplied by Bandil Erection of duct bank in the scope of contractor AL/QU conductor Power/Control cable 1100 grade, XLPE 1.1 KV GR., 2012.5.50 MM. CU-XLPE 1.1 KV GR, 12Px1.5 50 MM, CUXLE C Laying of cable tray of following sizes inside concrete Trenches, existing rack or cable support angles, fixing on platforms, on bridge like structures including unloading and transportation of cable tray from owners store to site, unpacking, visual inspection, fixing of cable tray cover for top layer on tray, fixing of z claim and bolting of tray with support as per approved drawing. Al paint will be supplied by contractor. 200Wide perforated cable tray D 100Wide perforated cable tray Cable termination Glanding, termination and connection of 1.1KV grade aluminium /copper conductor PVC/XLPE insulated, armoured power & control cables of following sizes by double/Single compression type brass cable gland and crimping Type AL/tinned Cu. lugs with ferrules, marker tapes including drilling and tapping of gland plates, connection to equipment terminals through Gl conduit (Glands and lug, HT Termination kit, Jointing KIT to be supplied by B&R on free issue basis and other material like ferrul, al tag plate, marker etc will be supplied by contractor) 1.1 KV GR, 30x2.5 50 MM, CU-XLPE 2 2 11 KV GR, 12Px1.5 SO MM, CU-XLPE 4 1/2 INCH CABLE GLAND E 32 MM CABLE GLAND LOADING, UNLOADING STORING FABRICATION AND ERECTION IN POSITION, ALLIGNMENT, BOLTED AND/OR WELDED STRUCTURAL STEEL (LIGHT) WORKS OF GRADE 8350 BR (CONFIRING TO 15:2062 GRADE -A/B AT ALL LOCATION AND ELEVATION UP TO 12 MTR ABOVE FGL INCLUDING ALL BUILT UP SECTION/COMPOUND SECTION MADE OUT OF ROLE SECTION AND/OR PLATES/BEND PLATES IN ALL TYPES OF STRUCTURAL FRAME WORKS, FLOOR BEANS STAIRS, PLATFROM, HAND RAIL OR ANY OTHER LIGHT STEEL STRUCTURAL ITEMS OR ACCESSORIES TO SUPPORT CABLE TRAY, VALVES, PIPING, INSTRUMENT, PUMP ETC. WITH FIXING IN LINE AND LEVEL WITH TEMPORARY STAGING AND BRACING AND REMOVAL OF THE SAME AFTER ERECTION AND TO COMPLETE IN ALL RESPECTS AT IOCL BARAUNI REFINERY PREMESSE AND STP AREA. PROVIDING OF LABOUR AND ALL CATEGORIES, SUPPERVISION IN ACCORDANCE WITH THE DRAWING SPEC AND INSTRUCTION OF ENGINEER INCHARGE
