Providing Additional Tourist Facilities At Mtdc Resort Mahur Dist Nanded-PART A - Work Portion Removing grass, gazer grass and disposing off out of building premises including making clean the ground by shovel and phavaras etc. complete. (Item No. 21.34) Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to distance of 50m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete.(Lift upto 1.5m.) By Mechanical Means (Item No. 21.02) Excavation for foundation in Hard murum and boulders including removing the excavated material upto a distance of 50 metres, beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete.(Lift from 1.5m to 3.0m.) By Mechanical Means (Item No. 21.12) Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth/murum, ramming, watering including shoring and strutting etc. complete.(Lift from 1.5m To 3.0m.) By Mechanical Means (Item No. 21.16) Excavation for foundation in Hardrock by blasting including trimming and leveling the bed by chiselling where necessary and removing the excavated material and stacking it in measurable heaps within a distance of 50 metres from the building area including dewatering and back filling with available earth/murum watering, ramming etc. complete.(Lift from 1.5m To 3.0 m) By Mechanical Means (Item No. 21.18) Providing preconstructional antitermite treatment as per I.S. 6313(Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper. (Item No. 21.22) Filling in plinth and floors with approved excavated material in 15cm. to 20cm. Layers including watering and compacting etc. complete. (Item No. 21.36) Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15cm to 20cm including watering and compaction etc. complete. (Item No. 21.37) Providing dry/trap/granite/quartzite/gneiss rubble stone soling 15cm to 20cm thick including hand packing and compacting etc. complete. (Item No. 21.38) Providing and laying Cast situ/Ready Mix cement concrete M15 trap/granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.(Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 24.08) Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/granite/quartzite/gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork, cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided(Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 25.13) Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/granite/quartzite/gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 25.33) ... (Item No. 25.33, First Floor) Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/granite/quartzite/gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 25.52) ... (Item No. 25.52, First Floor) Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/granite/quartzite/gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 25.72) ... (Item No. 25.72, First Floor) Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/granite/quartzite/gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 26.19) ... (Item No. 26.19, First Floor) Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/quartzite/granite/gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete.(Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 26.26, First Floor) ... (Item No. 26.26, First Floor) Providing and fixing in position TMT-FE-500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. Item No. 26.33) ... (Item No. 26.33, First Floor) Providing and laying damp proof course 50mm thick in M20 cement concrete layer and bitumen/using cement with waterproofing compound curing, formwork etc. complete. (Item No. 31.01) Providing second class Burnt Brick masonry with conventional/I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/in plinth external walls including bailing out water manually, striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete. (Item No. 27.01) Providing second class Burnt Brick masonry with conventional/I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete Item No. 27.05) ... (Item No. 27.05, First Floor) Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap/granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.(Wooden centering will not be allowed.) With fine aggregate(Crushed sand VSI Grade) (Item No. 24.16) Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. (Item No. 32.04) ... (Item No. 32.04, First Floor) Providing and applying plaster/wall punning with plaster of paris(with plaster of paris material) in 10 to 13 millimeter thickness to previously plastered surface/or on newly brick surface(Excluding rough cast plaster) in all position including preparing and Finishing the surface scaffolding etc.complete. (Item No. 32.30) ... (Item No. 32.30, First Floor) Providing waterproof plaster in W.C. and bath 20mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing(and filling joints of Nahani trap and any outlet by properly) etc. complete. (Item No. 31.07) ... (Item No. 31.07, First Floor) Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. (Item No. 32.11) ... (Item No. 32.11, First Floor) Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6mm thickness or Tape Grooves 35 to 45mm thickness or as required, in all position including preparing the surface, scaffolding etc. complete. (Item No. 32.32) ... (Item No. 32.32, First Floor) Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete. Item No. 32.34) Providing and applying Royale Luxury Emulsion of approved make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. wall primer with brush by adding mineral turpentine oil by 8 to 10 % or water by 15 to 20% allowing to dry for 6 to hoursAfter applying acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45% or 65 to 70% by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45% or 65 to 70 % by roller.(With prior approval of S.E.) (Item No. 36.21) Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning, preparing the plaster surface, applying primer coat, scaffolding if necessary, and watering the surface for two days etc complete. NOTE: For Item number 15 to 18 prior approval of Superintending Engineer will be necessary (Item No. 35.26) Providing and laying Vitrified MATT finish having decorative type of size 1000 millimeter x 1000 millimeter of 8 to 10 millimeter thickness (on a existing flooring) with bonding chemical and confirming to IS 15622-2006 (Group Bla) of approved make shade and pattern for flooring in required position laid on a bed of bonding chemical filling joints curing and cleaning etc .complete. ... (Item No. 33..61, First Floor) Providing and laying vitrified rustic matt stone finish tiles having size 590mm to 605mm x 590mm to 605mm to 8 to 10mm thickness and confirming to IS. 15622- 2006(Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete. (Item No. 33.45) ... (Item No. 33.45, First Floor) Providing and fixing machine cut machine polished 18mm to 20mm thick telephone black/Amba White/Cat bary brown/RBI red/Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. (Item No. 33.35) ... (Item No. 33.35, First Floor) Providing and fixing solid core flush door shutter in single leaf 32mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete. (Item No. 39.09) ... (Item No. 39.09, First Floor) Providing and fixing fiber glass reinforced polyster door shutter 35mm thick as per IS 14856(2000)(Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc complete. (Item No. 39.59) ... (Item No. 39.59, First Floor) Providing and fixing 30mm thick PVC FLUSH L DOOR SHUTTER consisting of panel of hollow PVC profile of 20mm thickness consisting frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mminserted inside the hollow section of stiles rails top ?and bottom rails and two 19x 19mm MS tubes inserted horizontally inside the hollow profile section using 4/5mm sheet using screws hollow profile shall be lipped with 10mm(5mm x2) thick x 20mm width on stiles and rails using solvent cement. The inner panel shall be laminated with 5mm thick termite proof waterproof plain/prelam PVC sheet using solvent cement on the both sides of the panel including stainless steel fixtures and fastening etc. Complete as per direction of Engineer incharge, manufacturers specification and drawing. (Item No. 39.82) Providing and fixing of factory made uPVC Sliding window & door(White Colour) complete, comprising uPVC multichambered frame having in-built uPVC roller track on top and uPVC sash with wall thickness of 2.3mm(+-0.2mm), duly reinforced with G.I. section 1.5mm, wherever required. uPVC window & door profile shall be made in India & shall conform to BS EN 12608 and other standards as mentioned below: S.No. Name of the test Test Method Specified Parameter 1 Tensile Impact Strength ISO 8256- more than 700Kj/m2 2 Vicat Softening Temperature EN ISO 306 Shall not be < 750C 3 Charpy Impact Strength EN ISO 179-2 Shall not be < 20KJ/m2 4 Flexural Modulus Elasticity EN ISO 178 Shall not be < 2200 N/mm2 5 Mean Breaking Stress for welded corner(a) For the tensile bending test EN 514 Shall not be < 25 N/mm2(b) For the compression bending test Shall not be < 30N/mm2 6 Heat Reversion Test IS:4985-2000 Shall not be > 2.0 % 7 Surface Spread of flame BS : 476-Part 7 Classification 1 8 Ignitability Evaluation BS : 476- Part 5 P Not easily ignitable 9 Tensile modulus ASTM D 638 Shall not be < 35 MPa 10 Shear Modulus ASTM D 732 Shall not be < 220 MPa 11 Tensile Strength EN ISO 527 Shall not be < 30 MPa All corners of frame and sash will be fusion welded. After placing 5mm Float Annealed glass in the sash, uPVC glazing bead, interlock, EPDM/TPE gasket, brush shall be provided including touch lock and rollers & proper drainage system shall be provided. Window/Door will be fixed to the wall with 100mm long and 8mm dia. Fasteners and complete in all respect as per direction of Engineer-In-Charge. uPVC Window and Door Profiles are warranted for a period of ten(10) years against non-uniform discoloration, wrapping and rotting under general use. :: 3 Track 3/ Sash(Big Series) window frame of size 122 x 54mm & Sash of size 64 x 47mm (Item No. 54.08b) ... (Item No. 54.08b, First Floor) Providing and laying telephone black/Amba White/Cadburybrown/Ruby red/Ocean Brown granite stone of 18 to 20mm thick for door frame/dado/window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete. (Item No. 33.68, First Floor) ... (Item No. 33.68, First Floor) Providing and fixing 900mm high S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top, 40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 8mm thick toughened glass including fabricating, fixtures, errecting, necessary welding, grinding, finishing, buffing to stainless steel pipe etc. complete Item No. 40.07) (Item No. 40.07, First Floor) Providing and fixing in position Gypsum board false ceiling with 12.5mm thick Gypsum boards, screwed/fixed to the under structure of suspended G.I. Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50mm maximum center to center distance 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete. Item No. 38.51) (Item No. 38.51, First Floor) Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness incm 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm thick brick bedding incm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years guarantee on requisite stamp paper including curing etc. complete. (Item No. 31.26, First Floor) Providing cement based water proofing treatment to terraces(Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20mm. thick layers of same mortar added with jute fiber at 1Kilogramper bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/-including ponding test etc. complete. (Item No. 31.04) Providing and constructing granite kitchen platform with fixing of stainless steel sink 600mm x 450mm size as per detailed drawing including vertical both side polished kadappah stone 25 to 30mm thick supports with kadappah top 35 to 40mm thick and polished granite 16 to 20mm top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15cm height and top granite of 75 x 40cm including cutting, opening for sink of required size in kadappah as well as granite etc. complete.(Platform top size 5.00m x 0.60m and height is 0.75 m) (Item No. 41.78, First Floor) Providing and fixing Table top white wash basin of size 120x635x405mm rubber plugs and brass chain, with pillar cock, C.P.Angular stop cock long thread, continental including S.S. bottle trap of approved make having necessary pipe connection up to theoutside face of the wall.etc complete as directed by Engineer in charge. Providing and fixing white european type wall-hung pan, of size 350mm x 355mm x 570mm concealed flush tank with floormounting frame installing kit and drain pipe connection set for wall hung WC, with approved make square control plates including soil pipe, vent pipe upto the outside face of wall, 100mm dia C.I. plug bend inlet pipe all fittings, cutting & making good walls, floors etc. complete. (Item No. 48.41) Providing and fixing 10cm PVC nahani trap with grating etc. complete. (Item No. 42.67) Providing and fixing C.P. pillar cock long neck with aerator of approed make including necessary sockets/union nut etc. complete. Item No. 42.82) Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/union nut etc. complete. (Item No. 42.83) Providing and fixing Mirrors size:1200mm X600 mm of approved Indian quality, copper plated with 10 mm (3/8) thick ply wood backing, in the masonaryas per Architect.s drawing and make approved as Directed by Engineerin- charge etc. complete. Providing and fixing on walls/ceiling/floor 15mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. (Item No. 42.55) Providing and fixing on walls/ceiling/floor 25mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. (Item No. 42.57) Providing and fixing on walls/ceiling/floor 40mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. (Item No. 42.59) Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. (Item No. 42.09) Providing and fixing 75mm dia stabiliser pipe/P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete (Item No. 42.51) Providing and fixing 100mm dia stabiliser pipe/P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. (Item No. 42.52) Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 4:8 cement concrete foundation 2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and airtight C. I. cover of 75Kilogramwith lid and frame fixed in cement concrete. (Item No. 42.10) Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and C.I. lid cover of 75Kilogramwith lid and frame fixed in cement concrete. (Item No. 42.11) Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number, filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. (Item No. 42.87) Providing and laying Cast in situ/Ready Mixcement concrete M- 25 of trap/granite/quartzite/gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. With fine aggregate(Crushed sand VSI Grade) (Item No. 26.07) Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/square metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. (Item No. 40.01) Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted/bolted/welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. Item No. 23.01) Providing and fixing divertor with overhead shower,shower arm,spout,hand shower with wall bracket having flow rate up to 12 liters/minutes of Jaquar/Cera/Hindware /Perryware or equivalent make including all necessary pipes,fittings etc.complete as directed by Engineer In Charge.( Make shall conform to manufacturers Green product and shall got approved from the Engineer In Charge.) Suppying and fixing Roller blinds Curtain on windows made out of imported fibrics and rollers with level for rotic movement and stairing for side movement fitted in matching powder coated aluminium channel fixed in mannar tio insure smooth operation as per Architect.s drawing and make approved as Directed by Engineerin- charge etc.complete.. Providing & fixing WARDROBE with Sovenir glass shelf & Glass Door having size of 1000X2100X600 mm made up of CENTURY / GREENPLY commercial PLY BWR grade ply. (ISI 303) MARK or equivalent with 25mm, 18mm, 12mm plywood to frame works, shutters, shelves constructing upper and lower Wardrobe having one shelves for each as per approved drawing including hinges for shutters, magnet , s.s. chain, ss handles, drawer lock EML and finished with 1mm thick laminate & 0.8mm thick white laminate ROYAL TOUCH / GREEN PLY make confirming (ISI 2046) or equivalent make premium quality in approved design and groves, plywood edges to be finished with BTC lipping , outer edges melamine polishing as directed by engineer in charge / Architect etc complete.. Providing and Supplying on site FABIO 3 Seater Sofa having size 29 X 74 made out of 75*38mm unfinished size) C.P.T.W. sections frame, 6 mm ply. Generally confirming to IS (303) (anchor or equivalent) for necessary covering from back & arm rests. seat shall be 125mm and back shall be 100 mm thick duly covered with tapestry fabric / compositor leather (not less than Rs. 350/- RMT.) and foam od density including hardware , navel, jute cloth, casement , spring etc., complete. All exposed wooden surface shall be melaine polished and antitermite treatment to plywood and woodwork with 5 year guarantee bond etc .including lifts and leads etc., complete as per architect drawing and instruction of engineer in charge. Providing and fixing H.D.P container one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20, 000 litres (Item No. 42.54) Providing and fixing C P brass Central Hole Basin Mixer JAQUAR BATH FITTINGS & SANITARYWARE (Item Code 5005 B / 5001 B) Providing and fixing C P brass Waste Coupling 32 mm (Full Thread) JAQUAR BATH FITTINGS & SANITARYWARE Item Code 750 L130 CP) Providing and fixing C P brass Angle Stop Cock with Flange JAQUAR BATH FITTINGS & SANITARYWARE (Item Code 5053 CP) Providing and fixing C P brass Metropole Flush Valve JAQUAR BATH FITTINGS & SANITARYWARE (Item Code 1093 CP) Providing and fixing Bib Cock JAQUAR BATH FITTINGS & SANITARYWARE (Item Code CON-037 CP) Providing and fixing C P brass Double Hook JAQUAR BATH FITTINGS & SANITARYWARE (Item Code 1161 N CP) Providing and fixing C P brass Towel Ring JAQUAR BATH FITTINGS & SANITARYWARE (Item Code 1181 N CP) Providing and Fixing Jet spary .etc complete. Providing and fixing in position double bed of size 2150mmX 1980mm X450mm with made up of CENTURY / GREENPLY MAKE commercial PLY BWR grade ply. (ISI 303) MARK or equivalent with 18mm ply used for approved drawing and finished with 1mm thick laminate ROYAL TOUCH/GREEN LAM confirming to (ISI 2046) or equivalent make premium quality in approved design and groves, as directed by engineer in charge Architect etc. complete.. Providing and placing in position approved quality Double bed mattress size 2150X1980X125 mm Supplying Mattress (50mm bonded plus 25 mm U foam) Total 75 mm as directed by engineer in charge / Architect. With 5 year guarantee on court fee stamp of Rs. 100 /- ) as per Architects drawings and approved make as directed by Engineer in charge etc. complete. Providing & fixing SIDE TABLE for over all size 600mm x 600 mm 450mm height with made up of CENTURY /GREENPLY commercial PLY BWR grade ply. ISI 303) MARK or equivalent with 12mm ply used for approved drawing with and finished with 1mm thick laminate & 1 MM white laminate ROYAL TOUCH / GREEN LAM confirming to (ISI 2046) or equivalent make premium quality in approved design and groves, plywood edges to be finished with BTC lipping, outer edges melamine polishing as directed by engineer in charge / Architect etc complete. Providing & placing in position Dressing table having size 1000x450x1800 mm made up of 18 mm thick CENTURY / GREEN PLY commercial PLY BWR grade ply. (ISI 303) MARK or equivalent & 5mm Thick glass made up of as per approved drawing including hinges for shutters, magnet , ss handles ,drawer lock EM, telescopic channels, and finished with 1mm thick laminate & white laminate 1mm thick ROYAL TOUCH / GREEN LAM confirming to (ISI 2046) or equivalent make premium quality in approved design and groves, plywood edges to be finished with BTC lipping, outer edges melamine polishing as directed by engineer in charge / Architect etc complete. Providing and supplying double & single bed-sheets ,pillow covers for two pillows as per architects drawing and make approved as directed by engineer incharge etc.complete Providing ans supplying Comfater for Double & single bed of approved quality as per architects drawing and make approved as directed by Engineer-in-charge etc complete Providing and Supplying on site godrej / swadeshi / equivalent low back non revolving, non tilting chairs with powder tubular pipe structure for visitor (type B ) chairs shall be of high density foam for optimum seating comfert, without height adjustment with arm test. the chair shall be provided with approved type tapestry up to RS. 300/- per meter with necessary beading wherever require. all metal work shall be powder coated as per architect drawing and instruction of engineer in charge. 5 year guarantee on court fee stamp of Rs. 100 Providing and placing in position tea coffe table 600X 450 X 450mm with 2 chiar made up of CENTURY /GREENPLY commercial PLY BWR grade ply. (ISI 303) MARK or equivalent with 18mm ply & 10mm thick Clear glass used for approved drawing with and finished with 1mm thick laminate & 0.8MM white laminate ROYAL TOUCH GREEN LAM confirming to (ISI 2046) or equivalent make premium quality in approved design and groves, plywood edges to be finished with BTC lipping , outer edges melamine polishing as directed by engineer in charge Architect etc complete. Providing & fixing TV Unit having size of 1900 X 380 X 2100 mm made up of CENTURY / GREENPLY commercial PLY BWR grade ply. (ISI 303) MARK or equivalent with 18mm, plywood1mm thick laminate & 1 mm thick white laminate ROYAL TOUCH / GREEN PLY make confirming (ISI 2046) or equivalent make premium quality approved design as directed by engineer in charge / Architect etc complete Providing & fixing STUDY TABLE having size of 1345X600X750 mm made up of 18 and 12mm thick CENTURY / GREEN PLY commercial PLY BWR grade ply. (ISI 303) MARK or equivalent made up of as per approved drawing including hinges for shutters, magnet, s.s. chain, ss handles, drawer lock EM, telescopic channels, s.s. magnet and finished with 1mm thick laminate & white laminate 1mm thick ROYAL TOUCH / GREEN LAM confirming to (ISI 2046) or equivalent make premium quality approved design and groves, plywood edges to be finished with BTC lipping, outer edges melamine polishing as directed by engineer in charge / Architect etc complete. Providing and supplying Bathroom Assessories like 17 liter Buckets, 2 liter Mug,dust bin , bathroom broom, etc. in bathrooms as per Architects drawing and approved Make as Directed by Engineer-incharge etc,complete. Providing and fixing in position paintigs on wall as per Architects drawing and approved as Directed by Engineer-in-charge etc,complete. Providing and supplying dry-wet Bath mat& Door to all Bath room as per Architects drawing and approved as Directed by Engineerin- charge etc,complete. Providing and supplying Turkish type (Face Towel) napkins as per Architects drawing and approved as Directed by Engineer-in-charge etc,complete. Providing and supplying Turkish Type Bath Towelas per Architects and approved as Directed by Engineer-in-charge etc,complete. Supplying and installing Office Signages Glass/SS with Vinyl as per Rooms cabin (Fire escape and Route prolite signages)as per Architects drawing and approved as Directed by Engineer-in-charge etc,complete. Providing & fixing DINNING TABLE & with Four Chair having size of 1200x1200x750 mm meter made up of CENTURY / GREEN PLY MAKE commercial PLY BWR grade ply. (ISI 303) MARK or equivalent make made up of 18mm plywood as per approved drawing and finished with 1mm thick laminate ROYAL TOUCH confirming to (ISI 2046) or equivalent make premium quality in approved design and groves, plywood edges to be finished with BTC lipping , outer edges melamine polishing and as directed by engineer in charge / Architect etc complete Providing & fixing SERVICE TABLE having size of 2500X450X750 mm made up of 18 and 12mm thick CENTURY / GREEN PLY commercial PLY BWR grade ply. (ISI 303) MARK or equivalent made up of as per approved drawing including hinges for shutters, magnet, s.s. chain, ss handles, drawer lock EM, telescopic channels, s.s. magnet and finished with 1mm thick laminate & white laminate 1mm thick ROYAL TOUCH / GREEN LAM confirming to (ISI 2046) or equivalent make premium quality in approved design and groves, plywood edges to be finished with BTC lipping, outer edges melamine polishing as directed by engineer in charge / Architect etc complete. Providing & fixing RECEPTION TABLE having size 3300x750x750 mm made up Corian sheet 19mm thick CENTURY / GREEN PLY MAKE commercial PLY BWR grade ply. ISI 303) MARK or equivalent make made up of 18mm & 12mm plywood & 18mm clear glass including hinges for shutters, magnet , s.s. chain, ss handles, drawer lock EM, telescopic channels, s.s. magnet as per approved drawing and finished with 1mm thick laminate & 1 mm Thick White Laminate ROYAL TOUCH confirming to (ISI 2046) or equivalent make premium quality in approved design and groves, plywood edges to be finished with BTC lipping , outer edges melamine polishing and directed by engineer incharge Architect etc complete. Providing & fixing Office TABLE having size of 1500 X600X 750 mm as per detailed drawing with following specifications made up of CENTURY / GREEN PLY MAKE commercial PLY BWR grade ply. (ISI 303) 18mm & 12mm thick commercial ply and drawers are made up of 18 mm & 12mm ply frame ply for back with 350 mm and 400 mm channels for the drawers sliders and using hinges shutters to be fixed either magnet s.s. doors chain, drawers lock and finished with 1 mm Laminate & 0.80mm Thick White Laminate confirming to (IS- 1328)or equivalent make premium quality in approved design and groves, plywood bottom to be finished with BTC lipping internal french polishing, outer edges melamine polishing and as directed by engineer in charge / Architect etc complete. Providing and fixing Double leaf glass door shutter with hydraulic door closersof 35mm thick and glass thickness 10 to 12 mm with frame, for solid core flush door, decorative type of exterior grade as per detailed drawings or as approved , all neccessary beads, moulding and lipping, brass oxidised / aluminium with powder coating fixtures and fastenings with mortise lock, chromium plated handles on both sides and finishing with french polishing etc. complete. (without frame) Providing supplying Strong folding S.S. Cloth Dryer (2 ft x 5 ft) as per Architects drawing and approved Make as Directed by Engineer-incharge etc,complete. Providing and Supplying Wall Clock as per Architects drawing and Make approved as Directed by Engineer-in-charge etc,complete. Providign & Fixing Wall Paper at wall suraface etc. Providing and fixing in postion Single bed of size 2150x1000x450 mm with made up of CENTURY GREENPLY MAKE commercial PLY BWR grade ply. (ISI 303) MARK or equivalent with 18mm ply used for approved drawing and finished with 1mm thick laminate ROYAL TOUCH/GREEN LAM confirming to (ISI 2046) or equivalent make premium quality in approved design and groves, as directed by engineer in charge Architect etc complete. Providing and placing in position approved quality Single bed mattress size 2150mm x1000mm x125mm Supplying Mattress (50mm bonded plus 25 mm U foam) Total 75as per Architects drawings and approved make as directed by Engineer in charge etc. complete. Providing and Laying factory made coloured chamfered edge Cement concrete grass paver blocks of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine fine aggregate(natural sand/crushed sand VSI grade finely washed etc.), compacting and proper embedding/laying of inter locking paver blocks into the fine aggregate(natural sand/crushed sand VSI grade finely washed etc.) bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine aggregate(natural sand/crushed sand VSI grade finely washed etc.) and cutting of paver blocks as per required size and pattern, finishing and sweeping extra fine aggregate(natural sand/crushed sand VSI grade finely washed etc.) and complete as per manufacturer spsecifications & direction of Engineer-in-Charge. 60mm thick CC paver block of M-35 grade concrete with approved colour and design & pattern. (Item No. 48.06) Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150mm in thickness. (Item No. 2.09) Providing earth work in embankment with approved materials obtained from other sources upto lead of 50m. including all lifts, laying in layers of 20cm. to 30cm. thickness breaking clods, dressing to the required lines, curves, grades & section, watering and compaction with vibratory roller with V-Sat attachment to achieve not less than 97 % of standard proctor density etc. complete(Material obtained from Other sources) (Item No. 2.28) Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader/Paver on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- Plant Mix Method and Grading-II Material (Item No. 3.02) Wet Mix Macadam -- Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub-base/base course on well prepared surface and compacting with vibratory roller to achieve the desired density. Laying By Grader/Paver. (Item No. 3.23) Providing and laying in situ cement concrete M-30 with tremix treatment for 200mm thickness for Concrete Road is including laying plastic sheet for 125 micron thickness with groove cutting of 4mm wide and 20mm deep with necessary refilling with polysuphide sealent(Pouring grade) confirming to BS : 5212- 1989 into sawed groove widened at top for sealent reservoir of specified size and shape as per detailed drawing including fixing Polyethylene foam backer rod of required diameter(excluding reinforcement) with coarsen and fine aggregate Using V.S.I.Quality Artifitial Sand etc. complete with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. Item No. 5.22b) Providing and constructing Columns ,footing & steel including Design supply fabrication & erection Tensile structure Roof with Fabric of 900 Gsm both side Coated with PVDF Lacquer System on both sides,titanium dioxide front side primer,lowwick, protected aginst microbial and fungal attack,UV- protected top caot of type 2 grade of required colour and shap and design including necessary M.S.tensile steel structure of hollow section,gusset plates bolts nuts,screws etc. complete with one coat of epoxy primer and two caot epoxy paint etc.all complete as specified and approved by architect the complete structrual structure Designed to withstand the wind pressure as per IS (PART III), to accmmodate thermal expansion and seismic movement etc The rate shall include all design calculations, engineering and slope drawing Including approval from cometent structural designer,Labour T &P scaffolding other incidental cahrges including wastage enabling temporary service all fitting fixtures complete as per technical specfication .for the purpose of Payment actual surafce area of fabric shall measured etc. Providing and laying for 150mm dia salt glazed stoneware pipe including fittings Such as bends, tees, single junction, double junctions laying, jointing(including excavation and refilling the trenches) complete. (Item No. 42.04) Providing and erecting chain link fencing 1.6 M. height with G.I. chain link of size 50 x 50 mm, gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, includind excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/c with iron bar 16mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25 x 25 x 5 mm size and vertical M.S. flat 35 x 5 mm and 25 x mm horizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm including 3 coats of oil painting etc. complete. Supplying hard murum/kankar at the road site, including conveying and stacking complete. (Item No. 2.29a) Spreading hard murum/soft murrum/gravel or kankar for side width complete (Item No. 2.30) Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering etc. complete. (Item No. 2.31) Providing & placing in position Head board for existing bed made up of 18 mm thick CENTURY GREEN PLY commercial PLY BWR grade ply. (ISI 303) MARK or equivalent & covered with cloth cushion made up of as per directed by engineer in charge / Architect etc complete. Stamp Concrete of 100mm Thickness-Providing and Laying in-situ M30 Grade unreinforced plain cement stamp concrete of 100mm thickness pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate(natural sand/VSI grade finely washed crushed sand) Confirming to IS 383, as per mixed in a batching and mixing plant/non tilting mixer and weigh batcher as per approved mix design, admixtures, transporting to site in nagpur city with lead upto 20KM(on Inner Ring Road from Avasti nagar to wadi), spreading, laying with approved make pover, compacted and finished in a continous operation, finishing to lines and grades Also Providing, Placing and applying stamp powder which is light fast UV resistant pigment with appropriate chemical compounds of desired colour on base concrete after excess bleed water has evaporated using dry shake method @5kg persqm. Including texturing, and covering with plastic sheet(min 200 micron thickness) and also applying two coats of UV-stable, 30 % solids clear sealer @ 150 to 250 gms persqm using surface roller and protecting from falling dust, dirt and curring by curring compound/by providing cement vata in cement Mortor 1 :8 @ 0.6m 0.6m center to center, admeasuring 80mm at bottom and 40mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-incharge or Landscape architect etc. complete.(prior approval of superinteding Engineer will be necessary) (Item No. 54.01) Excavation for planting lawn in earth, soil of all types, soft murum, including removing the excavated material up to a distance of 50 mtrs. for a depth of 30 cms.(As per P&G DSR 2022-23 Items of garden work,Sr No.3) Supplying on site fresh Garden soil (free from stones rubbish like dried grass roots, other such materials) for excavation area of depth of 30 cms.( consolidated thickness).(As per P&G DSR 2022-23 Items of garden work,Sr No.36a) 75% garden spil Supplying on site well decomposed Farmyard Manure for excavation area of depth of 30 cms. (Consolidated thickness). (As per P&G DSR 2022-23 Items of garden work,Sr No.36b) 25% manure Filling fresh garden soil / silt & manure in excavated area of depth 30cms. (As per P&G DSR 2022-23 Items of garden work,Sr No.13) Mixing garden soil/silt & manure thoroughly well, watering previous night. Planting reqired plant species, lawn grass as directed etc. complete for required depth 30 cms. for planting lawn/ shrub/ flower bed/ hedges/ edges/ canna bed/ ground cover. (1/10 of semiskilled labour)(As per P&G DSR 2022- 23 Items of garden work,Sr No.23) Providing on site well established (free from weeds /disease etc.) ready to fix lawn turf in slabs/ rolls of required variety as directed. (As per P&G DSR 2022- 23 Items of garden work,Sr No.47) Maintainance of Newly Developed lawn Area. For First 30 days Only (Paspallum/ selection)(As per P&G DSR 2022-23 Items of garden work,Sr No.28) 1 37.000 Per set Sieve Analysis 2 31.000 Per set Field Moisture Content Liquid limit & Plastic limit Compaction Test (Proctor Density) CBR Test (Lab) With compaction test CBR Test [Field Determination Test) Excluding Transportations per IS 2720 Part XXX] Field Density by sand replacement method Sulphate & Chloride Contents. Mechanical Analysis. Plate Load Bearing Test. [Excluding Transportation ] Water Absorption, Specific Gravity, Impact Value, Crushing Value Flakiness Index/ Elongation Index Soundness Standard Consistency Fineness,Specific Gravity, Setting Time ( Initial & Final), Compressive Strength, Soundness PH Value, Sulphate & Chloride Content Fineness Modulus (Sieve Analysis), Silt & Clay Conten Chloride & Sulphate Content Upto 16 mm (Set of 3 Bars) Above 16 mm (Set of 3 Bars) (Tensile strength, %, Elongation, Yield Stress, Weight-Per Meter, Bend / Rebend Test, Proof Stress.) Nitrol Solution Test. (Set of 3 Bars) Water Absorption, Compressive Strength, Efflorescence Knife Test, Adhesion Test, End Immersion Test Water Absorption , Specific Gravity Free swell Test for soil Abrasion value Strupping Value (For bituminous work) Soundness BulkDensity Compressive strength of C.C.Cube (Set of 3 cubes) Concrete Mix Design (With all Tests on basic materials) Flexural strength of Beam (For Rigid Pavement Only) Permeability Test (For Rigid Pavement Only) Taking of core samples in concrete pavement. (Excluding Dead journey charges) Drying Time Dry Film Thickness Flexibility. Gel Time Pot Life. Volume of Solid.
