Tender For Repair/ Maintenance Of Boundary/ Compound/ Retaining Wall At Ne Zone At Rms.; 1 Demolition of cement concrete in ground floor and pavings n.exc 15 cm thick below or above ground levelcomplete all as specified and as directed. 2 M & L for precast cment concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) as bond stone including necessary form work setin CM (1:6) complete all as specified and as directed. 3 M & L for PCC (1:3:6) type C-1 (using 20mm graded stone aggregate)as in coping including necessary form work complete all as specified and as directed. 4 M & L for walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in CM (1:4) including provision of weep holes including demolition of old stone boulder masonry complete all as specified and as directed. 5 M & L for walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in CM (1:6) including provision of weep holes including demolition of old stone boulder masonry complete all as specified and as directed. 6 All as per ser No 4.00 (here-in-before) but except stones. 7 M&L for raised pointing to random or polygonal rubble uncoursed or brought up to course in CM (1:4) complete all as specified and as directed. 8 S&F for 110 mm dia PVC (SWR) pipe single socketed in any length with rubber joints laid in trenches/,floor/weep holes and similar work all complete all as specified and as directed. 9 Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in deepth; for foundation etc or for shafts, wells, cesspits, manhole, pier holes, etc n.exc 10 Sqm on plan andn.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed. 10 M & L for PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in foundationcomplete all as specified and directed. 11 M&L for brick work with sub class B bricks(using old size burnt bricks) straight or curved on plan exc 6 m mean radius built in CM (1:6) including demolition of old brick work complete all as specified and as directed. 12 All as per ser No 11.00 (here-in-before) but except bricks. 13 S & F in repairs Providing precast cement concrete louvres and jallies,type B-0, (1:2:4) (using 12.5 mm graded stone aggregate) 25mm thick (mea sured solid) and setting in mortar (1:4),including necessary form work and mould complete all as specified and as directed. 14 M&L for RCC nominal mix (1:1.5:3) type A-1 (using 20mm graded stone aggregate) as in band, coping, bed plate, benchingetc including slightly rounded of chamfered angle, throating, including demolition of reinforced cement concrete complete all as specified and as directed. 15 M&L for RCC nominal mix (1:1.5:3) type A-1 (using 20mm graded stone aggregate) in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like including demolition of reinforced cement concrete complete all as specified and as directed. 16 M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed. 17 All as per ser No 16.00 (here-in-before) but8 mm dia for stirrups. 18 M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) and similar work all as specified. 19 M&L for precast RCC (1:2:4) type B-1 (using 20mm graded stone aggregate) in drain slab cover ,including necessary form work complete set in cement mortar (1:6) including demolition of old reinforced cement concrete complete all as specified and as directed. 20 M&L for 15 mm thick rendering in CM (1:4) mixed with water proofing compound @3% by wt of cement, on fair faces of brick/concrete surfaces and surface finished even and fair without using extra cement complete all as specified and as directed. 21 M&L for 15 mm thick rendering in CM (1:6) on brick work or concrete surface, including preparation of surfaces and finishing the surfaces fair and even including taking down cement plaster complete all as specified and as directed.. 22 M&L for 15 mm thick rendering in CM (1:6) on brick work or concrete surface, including preparation of surfaces and finishing the surfaces fair and even complete all as specified and as directed. 23 Supply only integral water proofing compound (ISI marked) complete all as specified and as directed. 24 M & L for preparation of new surfaces of wall and applying three coats of white wash on walls complete all as specified and as directed. 25 M & L for preparation of old decorated surfaces of walls (plastered) by brooming down with steel wire brushing and applying one coat of white wash on wall complete all as specified and as directed. 26 Material and labour for preparation of new external surfaces of walls including cornices, pilasters etc (Plastered or un plastered surfaces) and applying two coats of cement based paint over a coat of primer complete complete all as specified and as directed. 27 M&L for preparation of old decorated surfaces of walls including cornices, pilasters etc (plastered or unplastered surfaces) andapplying one coat of cement base paint complete all as specified and as directed. 28 M & L for complete removal of existing treatment of plastered surface of wall and applying two coats of cement base paint complete all as specified and as directed. 29 M&L reinforced concrete pipes, class NP-2 ,300 mm dia laid and jointed complete with collars including demolition and breaking up drain pipes (salt glazed, stoneware, AC or reinforced concrete) setin cement mortarcomplete all as specified and as directed. 30 M&L for 75mm thick PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in Sub floors,sub bases,floors and paving finished even and smooth without using extra cement complete all as specified and as directed. 31 S&F for mild steelwork in post &struts in fencing including cuttingto shape as directed ,drilling holes notching for wire etc including flat iron fillets for securing wire mesh etc including all necessary drilling bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 including dismantling of old mild steel work including bracing, balusters, Sheet cladding like other complete all as specified and as directed. 32 S& F in repair mild steel nuts and bolts with washers of length of bolt exc 5cm but nexc 10cm and dia of neck 11 to 15mm machine made suitable for fixing of MS plate /angle bracing including dismantling of old mild steel workcomplete all as specified and as directed. 33 S&F in repairs 2 strand, steel bared wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rail, straining bolts, including securing or tying at crossings with and provision of galvanised MS wire staples of steel pins complete all as specified and as directed. 34 Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc. 25cm in soft/loose soil complete all as specified and as directed. 35 Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point in soils complete all as specified and as directed. 36 M&L for preparation of old painted surfaces of steel and iron work of any description over 10 cm width or girth not otherwise described and painting one coat of synthetic enamel paint in tint complete all as specified and as directed. 37 S&F concertina coil razor type fixed with galvanissed J clips, with angle iron of the following specification :-(a)Dia of coil when unstretched 600mm(b)No of circles 50 per coil(c)Nos of razor per RM 160(d)Weight of each coil 8 Kg(e)Coverage per coil 6 mtr(f)Centtral core wire made from high tensile spring steel core wire conforming to IS:4454 duly hot dipped galvanised (conforming toIS-2629) with diammeter 2.59 mm +0.05 mm, UTS 145-160 Kg/Sqm zinc coating 250-300 /sqm(g)strip : Electro galvanized steel strip 0.50 + 0.02 mm thick, width 19 mm (before wrapping on centtral core wire), conforming to IS - 1573, zinc coating 120 gm/sqm and bitumiinised dipped, width of barbs 11.50 mm, pitch of barbs 25.4 mm+ 0.20mm(h)Handle and spikes to be provided as required complete all as specified and directed 38 M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and as directed.
