Tender For Addn/Altn To Toilets In Tech Area For Agniveervayu (Women) At Af Stn Jodhpur; 1 Demolition of cement concrete in ground floors annd paving not exc 15 cm thickness (below or above ground ) and disposing of debris outside MD Land complete all as specified and as directed. 2 Dismantling floor ,hearth or wall tiling inclunding cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. 3 Taking down chowkts or frames with shhutter (without taking off shutters from the frame) exceeding 1.5 Sqm not exc 4 Sqm each complete all as specified and as diected. 4 Taking down chowkts or frames with shhutter ( without taking off shutters from the frame ) not exceeding 1.5 Sqmeach complete all as specified and as diected. 5 Taking down shutters of any description area exc. 1 Sqm complete all aas specified and directed. 6 Resecuring or easing & adjusting without taking down of shutters of any description area exc 2 Sqm complete all as specified and directed. 7 Dismantling of stone slabs and tiles of any description or thickness in floors, approns etc laid and bedded in any mortor all as directed. 8 Taking downcement or cement lime plaster work any description from brick or stone wall/ ceiling etc. including raking out of joints, hacking for key, scrubbing down with water etc complete all as specified & directed by the Engineer-in-Charge. 9 Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed. 10 M&L PCC (1:4:8) type D2(40 mm graded stone aggregate) for footing & plinth beam complete all as specified and directed. 11 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft to loose soil complete all as specified and directed. 12 Removing excavated soil not exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. 13 M&L for RCC- 1:2:4 type B1 (20mm graded stone aggregate) nominal mixin foundation, plinth beam, including rafts as mass concrete complete all as specified and directed. 14 M&L for form workfor rough finished surfaces of concrete measured flat for foundation & plinth beam complete all as specified and directed. 15 M&L for RCC- 1:2:4 type B1 (20mm graded stone aggregate) nominal mixin columns, piers, posts and struts complete all as specified and directed. 16 M&L for form workfor rough finished surfaces of concrete measured flat for columns complete all as specifed and directed. 17 M&L for RCC 1:2:4 type B1 (20 mm graded stone aggregate ) nominal mix in chajjas complete all as specified and directed. 18 M&L for form workfor rough finished surfaces of concrete measured flat for chajja complete all as specified and directed. 19 M&L for RCC 1:2:4 type B1 (20 mm graded stone aggregate ) nominal mix in beams, cantilevers, bresummers, lintel over 1.5 m span complete all as specified and directed. 20 M&L for form workfor rough finished surfaces of concrete measured flat for GF slab beam, lintel,cantilevers complete all as specified and directed. 21 M&L for RCC 1:2:4 type B1 (20 mm graded stone aggregate ) nominal mix in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all specified and directed. 22 M&L for form workfor rough finished surfaces of concrete measured flat for slab complete all specified and directed. 23 M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 24 M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 25 M&L for precast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar CM (1:4) type C1 (1:3:6) (20mm graded aggregate ) complete all as specified and directed. 26 M&L for precast cement concrete solid building blocks or slabs,10 cm thick (with plain or interlocking joints as directed) setting in mortar, complete all as specified and directed. 27 M&Lfor 10 mm thick 1:6 CM internal plaster on fair faces of walls finished even and smooth (without using extra lime or cement) complete all as specified and directed. 28 M&L for 5 mm thick 1:3 CM plaster on ceiling, finished even and smooth (without using extra lime or cement) complete all as specified and directed. 29 M&L for 15 mm thick (10 mm + 5 mm) in 1:4 CM external plaster on fair faces of walls finished even and smooth (without using extra lime or cement) complete all as specified and directed. 30 M&L for applying two coats of oil bound distemper over a coat of wall primer complete all as specified and directed. 31 M&L for three coats of white wash in ceiling complete all as specified and directed. 32 M&L for applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. 33 M&L for non - skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match & including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed. 34 M&L for vitrified ceramic tiles 10mm thick (square/rectangular) area of each tileexceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed by Engr-in-Charge. 35 Material & labour for vitrified ceramic tiles 10mm thick (square/rectangular) area of each tileexceeding 0.36 sqm but not exceeding 0.42 sqm, as in skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement mortar (1:4) complete all as specified and as directed. 36 M&L for cement concrete 25mm thick 1:2:4 type B0 (20mm graded stone aggregate) as inbase complete all as specified and as directed. 37 M&L for cement concrete 75mm thick 1:4:8 type D2 (40mm graded stone aggregate) as in sub base complete all as specified and as directed. 38 M&L for Glazed Ceramic Tiles In Vertical Surface 350X 250X 7 Mm/ 450X 350X 7Mm Thick Set And Jointed In Neat Cement Slurry And Pointed In White Or Colour Cement To Match & rendering 10 mm thick in CM (1:4) complete all as specified and as directed. 39 M&L for 75mm thick plinth protection PCC (1:3:6) using 20mm graded stone aggregate (0.90m wide) complete all as specified and as directed. 40 M&L for hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and as directed. 41 Demolition of cement concrete of any type description and in any position and dremoving debris ouside MD land complete all as specified and directed. 42 M&L for cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and directed. 43 M&L for brushing neat cement slurry with 3kg of cement per Sqm complete all as specified and directed. 44 M&L for 40 mm thick cement concrete 1:2:4type B0 (12.5 mm graded stone aggregate) in padding finishing surface of concrete topping even and smooth without using extra cement complete all as specified and directed. 45 M&L for 10mm thick plastering in cm 1:3 on green concrete roof surfaces with water proofing compound @ 3% by weight of cement, surface finished even and smooth without using extra cement complete all as specified and directed.Note :- WPC shall be measured and paid separately. 46 Supply only integral water proofing compound ISI Marked complete all as specified and directed. 47 M&L for applying APP modified membrane (minimum 3 mmthick), it shall be taken upto height of minimum 300mm and shall be inserted inside a groove cut in the parapet and fixed. If the height of parapet is 300mm or less, membrane shall be taken till top of the parapet and finished after covering the top surface to the parapet. For RCC inverted beam the whole beam shall be covered with membrane irrespective of the depth. In case of roof projection, the membrane shall be taken 50mm on the reverse side of roof at the edges.with non-woven polyster reinforcement/mat (centre core) with thermal insulation with white mineral gravel finish on upper side of membrane laid by torch application method with overlaps 75mm on length side and 100 mm on the width side as per manufacturer’s instructions over a coat of approved cold applied bituminous oil based primer (IS- 3384) @ 250 gm/sqm complete all as specified and as directed by Engineer-in-Charge. 48 S&F Solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reiforced with MS square tube, suppling & fixing in opening as per specification & drawing and as directed. 49 S&F Solid PVC door frame of size 50mm X 47mm made out of 5mm wood grain printed PVC sheet reiforced with MS square tube, suppling & fixing in opening as per specification & drawing. 50 S&F factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing and as directed. 51 S&F Factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing and as directed. 52 Supply & fixing approved colour powder coated(minimum thickness of powder coating 50 micron) aluminium frame for doors, window, ventilator with one or more rebates or aluminum section of two or more tracks incase sliding windows including jointing cleat for fixing complete all as specified & directed by the Engineer-in-Charge. 53 Supply & fixing approved colour powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed. 54 S&F 5.5mm thick sheet glass light colour selected quality fixed in door / window shutter cut to required size and fixed with neoprane gasket, area exceeding 0.50 Sqm in each pane area and solar control film reflective type sticked to glass panes as per manufacturers instructions complete all as specified & directed by Engineer-in-charge. 55 Supply & fixing stainless steel barrel tower bolt of size 150mmfixed in positions complete all as specified & directed by the Engineer-in-Charge. 56 Supply & fixing 125mm long mild steel butt hinges, cold rolled, medium weight complete all as specified and as directed. 57 Supply & fixingstainless steel handlesof size 125mm, complete all as specified and directed. 58 Supply & fixing 300 mm long stainless steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheetcomplete allas specified and directed. 59 Taking up or down steel tubing of 15 mm bore pipe and connection including cleaning for re-fixing or removal to storecomplete all as specified & directed by the Engineer-in-Charge. 60 Taking up or down steel tubing of 20 mm bore pipe and connection including cleaning for re-fixing or removal to storecomplete all as specified & directed by the Engineer-in-Charge. 61 Supply & fixing 15 mm bore, medium grade, galvanised iron pipe, with all fittings & fixed complete to walls & ceiling or laid in floor complete all as specified & directed by the Engineer-in-Charge. 62 Supply & fixing 20 mm bore, medium grade, galvanised iron pipe, with all fittings & fixed complete to walls & ceiling or laid in floor complete all as specified & directed by the Engineer-in-Charge. 63 Supply & fixing in repairs CP Bib taps, fancy type, 15 mm bore, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engr-in-Charge. 64 Supply and fixing in repairs two waybrass chromium platedfancy type bib cock 15mm bore complete all as specified and directed. 65 Supply and fixing in repairs 15 mm bore fancy type brass chromium plated telescopic wall mixer for mixing hot and cold water screwed down for iron pipe complete all as specified and directed. 66 Supply and fixing in repairs 15 mm bore center hole basin mixer brass, chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks & fly nuts for iron pipe complete all as specified and directed. 67 Supply and fixing in repairs of fancy typepillar taps brass, chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks & fly nuts for iron pipe of 15mm bore complete all as specified and directed. 68 Supply and fixing in repairsofbrass chromium plated fancy type soap dish complete all as specified and directed. 69 Supply and fixing in repairs 15 mm bore fancy typeoverhead shower with arm swivel joint chromium plated screwed down of size 200 mm x 200 mm complete all as specified and directed. 70 Supply and fixing in repairsofbrass chromium plated angle stop valves of 15mm bore screwed for 15mm bore iron pipe or union complete all as specified and directed. 71 Supply and fixing in repairstublar towel rail 20mm dia chromium plated brass of size 60cm long complete all as specified and directed by the Engineer-in-charge. 72 Supply and fixing in repairsofbrass chromium plated fancy type towel rack(two shelf) complete all as specified and directed. 73 Supply and fixing in repairs sheet glass corner shelf 300mm assembly consisting of 5.5mm thick sheet glass with chromium plated bracket guard and railingas approved by GE complete all as specified and directed. 74 Supply and fixing in repairs brass chromium plated handspray (Health faucet) with flexible pipe length not less than 1.00 m (minimum) fixed for EWC/IWC suitable for 15mm bore pipe complete all as specified and directed. 75 Supply and fixing in repairsbrass chromium plated paper holder for EWC complete all as specified and directed. 76 Supply and fixing in repairsof PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed. 77 Supply and fixing in repairs of vitreous chinawater closet (squatt pattern) complete including provision of lime concrete bedding fixed in repair of orissa pattern size 580x440mm, white, with and includingfoot rest (excluding flooring cistern & flush pipe) complete all as specified and directed. 78 Supply and fixing in repair of vitreous china wash down water closet pan (pedestal pattern) white and trap including connection to drain flush pipe and anti syphonage pipe. 79 Supply and fixingin repairs EWC seat cover PVC colour as approved by GE including all fitting arrangements complete all as specified and directed. 80 Supply and fixing in repairs of vitreous china wash down water closet single piece snow white with P/S trap including vitreous china flush cistern with twin flush and seat coverconnection to drain flush pipe and anti syphonage pipe complete all as specified. 81 Supply and fixing in repairsPVC valveless syphonic action type flushing cistern low level 10ltrs capicty white, fixed with new brackets complete all as specifed and directed Make. 82 Supply and fixing in repairsof flush pipe of polythene of low or high density or PVC 32mm for low level cistern complete all as specified and directed. 83 Supply and fixing in repairs of vitreous china WHB white flat back size 550mmx400mm on new brackets excluding taps waste china & plug including bracket etc complete all as specified and directed. 84 Supply and fixing in repairs of vitreous china WHB white flat back size 550mmx400mm with pedestal on new brackets excluding taps waste china & plug including bracket etc complete all as specified and directed. 85 S&F in repairs vitreous china urinals, half stall type, white,complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement; fixing with automatic sensor based urinal spreader for flushing with brackets, flush pipe, grating and Union for discharge pipe including PVC waste pipe, CP waste coupling, sensor based urinal spreader complete all as specified and directed. 86 S&F in repair vitreous china urinal, full stall type, white with urinal spreader bedding urinal against wall in cement mortar 1:2 securing urinal to, plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified and directed by Engineer-in-Charge. 87 Supply & fixing in repairs600 x 450 mm moulded glass looking mirror of selected quality and fixed to wooden plugs with chromium plated brass screws and cup washers in postion as directed. 88 Supply and fixing in repairsPVC Flexible waste pipe 32 mm dia with socket for steel sink upto floor level and length not less than 0.60 meter complete all as specified and directed. 89 Supply and fixing rotational moulded polyethylene water storage tank of capacity 1000 ltrs (Cylindrical vertical with closed top), three layer construction, ISI marked hoisted & fixed in position including GI light grade, over flow pipe 450mm and waste pipe 600mm long with all fitting etc. of 20 mm dia including dismantling/taking out of old water tank of having capacity of etc 500 ltr but not exc 1000 ltr & removing to site etc complete all as specified and as directed. 90 Supply and fixing rotational moulded polyethylene water storage tank of capacity 500 ltrs (Cylindrical vertical with closed top), three layer construction, ISI marked hoisted & fixed in position including GI light grade, over flow pipe 450mm and waste pipe 600mm long with all fitting etc. of 20 mm dia including dismantling/taking out of old water tank of having capacity of etc 250 Ltr but not exc 500 Ltr & removing to site etc complete all as specified and as directed. 91 Supply and fixing in repairs Gun-metal, globe or gate valves of 20mm bore with half turn lever arm /iron wheel head, screwed both ends for iron pipe complete all as specified and directed. 92 M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete(1:2:4) type B-1 using 20mm graded stone aggregate complete all as specified and directed by Engineer-in-Charge. 93 S&F in repair 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including necessary fittings complete all as specified and directed. 94 S&F in repair 75 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed. 95 S&F 75 mm dia PVC (SWR) bend any radius complete all as specified and directed. 96 S&F 75 mm dia PVC (SWR) junction single,(Single T) equal or unequal complete all as specified and directed. 97 S&F in repair 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including fittings complete all as specified and directed. 98 S&F in repair 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed. 99 S&F 110 mm dia PVC (SWR) bend any radius complete all as specified and directed. 100 S&F CP grating round 140mm size of PTMT (minimum weight 50 gms) complete all as specified and directed. 101 M&L for DWCPE (SN8) 180 (OD)/163(ID) mm diameter pipes laid in trenches including fittings complete all as specified and directed by Engi-in-charge. 102 Material & labour for construction of new stone masonary soakage well 3.0 meters dia and 3.0 meters effective depth inclunding soil work, in any type of soil, foudation in PCC 1:3:6, wall of honey combed masonary with top ring M25 concrete inclunding intercepting chamber abd screen chamber made of brick masonary in CM 1:6 RCC cover slab in M25/SFRC cover, interconnecting pipes of RCC/DWC complete all as shown on drg No. CEAA/TD/80 Sheet 1/2 & 2/2 and as specified & diected by the Engineer in charge. 103 M&L for onsite LLDPE septic tank (conventional type) designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection etc complete for 25 users complete all as specified and directed. 104 M&L for stone walling of squared rubble,uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed. 105 Taking down carefully copper/aluminium point wiring light ,fan, socket or power complete,such as switches, ceiling roses,pendents, regulators, sockets etc.removing materials to store for keeping in safe custody or for taking credit and making good disturbed surface of walls, floors etc. complete all as specified and directed by Engineer-in-Charge. 106 M&L for point wiring with 1.5 Sqmm multistrand, FRLS copper conductor cable, PVC insulated and unsheathed, drawing in and including PVC casing capping 20/25 mm dia medium grade ISI marked with all accessories such as bends, elbows reducers, pressed steel/ MS terminal boxes factory made 1.6 mm thick dully painted in rectangular shape appropriate sizefor one light/ fan point controlled by one 5 Amps switch one way, covered with 3 mm thick plastic laminated sheet top cover for mounting switches, sockets requlators etc and continous PVC insulated and unsheathed 1.5 Sqmm copper conductor cable multistrand as earth wire complete all as specified and directed. 107 All as per serial item No 106 above but 3 pin socket outlet, 5/6 amp on same board. 108 All as per serial item No 02 above but with 2.5 sqmm cable for independent one 6 pin 6/16 Amps socket outlet in and including2.5 Sq mm PVC insulated copper conductor unsheathed 1100 V grade IS-694 FRLS cable for continuous earth wire. 109 S&F in repair switch piano 5/6 amps flush type single pole one way complete all as specified and directed. 110 S&F in repair socket outlet flush type 5 pin 6 ampscomplete all as specified and directed. 111 S&F in repair switch piano 16 amps flush type single pole one way complete all as specified and directed. 112 S&F in repair socket outlet 2 in 1, 5 pin 16 amps flush typecomplete all as specified and directed. 113 Supply and fixing ceiling rose polycarbonate, isolated body 65 X 50 mm 2 to 3 terminalcomplete all as specified and directed. 114 Supply and fixing in repair non-metalic exhaust fan 300 mm sweep, 3/4/5 blade 230 volts, 1280 RPMconnecting up including provision of cable from ceiling rose/ connector to fan complete all as specified and as directed. 115 M&L for sub main wiring using two runs of single core PVC insulated cable with copper conductor multistranded 1100 volts of sizes 2.5 Sqmm through existing/ new non metalic PVC casing caping including copper earth wire in green colour of size 2.5 Sqmm connection to DB with thimbling complete as specified and directed. (Note:- Two runs of sub main wire including earth wire and rigid non metalic PVC conduit shall be measured as one unit per RM make of cable.) 116 S&F MCBs ofC series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of Single pole 6 to 32 ampcomplete all as specified and directed. 117 S&F 240V 10 KA C curve miniature circuit breaker (MCB) of SPN 32 AMP and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed. 118 Supply and fixing single pole neutral sheet metal enclosure for 04 way DBs when SPN to be used single phase 240 volts, single door complete all as specified and as directed. 119 Supply and fixing in repair LED 4 feet tube light fitting 1x 20W, 220V, AC metal body type connecting up withflexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.Make:- Crompton LDMTR20-CDL or equivalent approved in Havells/ Philips/ Bajaj/ Wipro. 120 Supply and fixing in repair LED 2 feet tube light fitting 1x 10W, 220V,AC polycarbonate body type connecting up withflexible copper conductor cable of suitable size from ceiling rosecomplete all as specified and as directed. 121 M&L for cutting holes 300mm diameter for preparing opening through brick/stone masonary wall for fixing non-metallic exhaust fan 300mm sweep, making good to damaged surface of wall, make a smooth circular surface and match with specification of existing wall complete all as specified and as directed.
