Tender For Repair/Maintenance Of Street Light, Security Light, Focus/Flood Lights, Lightning Arrester, High mast And Allied Works In New Chsc And Other Connected Area Under Age E/M-Ii Of Ge (South) Pune.; 1 S&F in replacement Electronic driver suitable for 90/120/150 watts LED security light fittings. Make should be as per the Existing manufacturer complete all as specified and directed. 2 S&F in replacement Electronic driver for 30/45/70 watts LED Security light/Flood light/post top. Make should be as per the Existing manufacturer complete all as specified and directed. 3 S&F in replacement Electronic driver for 100/150 watts flood lights. Make should be as per the Existing manufacturer complete all as specified and directed. 4 S&F in replacement Electronic driver for 200/250 watts flood lights. Make should be as per the Existing manufacturer complete all as specified and directed. 5 S&F in replacement Surge protection device(SPD) of capacity 10KV compatible with industrial & outdooor LED fixtures Make should be as per the Existing manufacturer complete all as specified and directed. 6 S&F in replacement MCB SP 230 volts C curve 6-32 amps complete all as specified and directed.. Make: L&T, ABB, Schneider 7 S&F in replacement MCB DP 230 volts C curve 6-32 amps complete all as specified and directed.. Make: L&T, ABB, Schneider 8 S&F in replacement MCB TPN 230 volts C curve 40-63 amps complete all as specified and directed.. Make: L&T, ABB, Schneider 9 S&F in replacement Digital time switch, DIN type daily / weekly with 25 ON/OFF programmes , 16 amps 250 volts ACcomplete all as specified and directed. Make L&T or Legrand/Indoasian 10 S&F in replacement Astronomical Digital time switch, 240 volts AC complete all as specified and directed.. Make L&T T2DDT7 or Legrand/Indoasian 11 S&F in replacement Power contactor 4 pole AC1 rating 130 A complete all as specified and directed. Make: L&T MCX 23 or equivalent in Legrand/ABB 12 S&F in replacement Power contactor 3 pole AC3 rating 32 A complete all as specified and directed. Make: L&T MNX 32 or equivalent in Legrand/ABB 13 S&F in replacement front mounting add-on aux contact block 2NO + 2NC for MNX/MCX contactors complete all as specified and directed. Make-L&T MNX A1 or equivalent in Legrand/ABB 14 S&F in replacement LED 30 watt street light fiitting made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP 66 protection with back opening separate driver compartment and having SPD 6 KV for protection incl complete fixing to pole/wall with necessary nut, bolts and washers complete all as specified and directed.Make: Luker Catpart No LSTE-30 or equivalent in Havells/ Phillips/ Bajaj 15 S&F in replacement LED 70 watt street light fiitting made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP 66 protection with back opening separate driver compartment and having SPD 6 KV for protection incl complete fixing to pole/wall with necessary nut, bolts and washers complete all as specified and directed.Make: Luker Catpart No LSTE-80 or equivalent in Havells/ Phillips/ Bajaj 16 S&F in replacement LED 90 watt street light fiitting made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP 66 protection with back opening separate driver compartment and having SPD 6 KV for protection incl complete fixing to pole/wall with necessary nut, bolts and washers complete all as specified and directed.Make: Luker Catpart No LSTE-90 or equivalent in Havells/ Phillips/ Bajaj 17 S&F in replacement LED 120 watt street light fiitting made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP 66 protection with back opening separate driver compartment and having SPD 6 KV for protection incl complete fixing to pole/wall with necessary nut, bolts and washers complete all as specified and directed.Make: Luker Catpart No LSTE-120 or equivalent in Havells/ Phillips/ Bajaj 18 S&F in replacement LED 150 watt street light fiitting made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP 66 protection with back opening separate driver compartment and having SPD 6 KV for protection incl complete fixing to pole/wall with necessary nut, bolts and washers complete all as specified and directed.Make: Luker Catpart No LSTE-150 or equivalent in Havells/ Phillips/ Bajaj 19 S & F in replacement of 30 watts flood light White/Warm white in colour, powder coated and waterproof pressure die cast aluminium enclosure, with inbuilt electronic drivers and SPD 6 KV and IP 66 protection complete ,Single phase, etc fixing in MS chanel by drilling hole of suitable , size, using nut, bolts and washers of suitable size as reqd at the site complete all as specified and directed by Engr-in-Charge. Make: Luker Catpart No LFLSL30NSG or equivalent in Havells/ Phillips/ Bajaj 20 S & F in replacement of 100 watts flood light White/Warm white in colour, powder coated and water proof pressure die cast aluminium enclosure, with inbuilt electronic drivers and SPD 6 KV and IP 66 protection complete ,Single phase, etc fixing in MS chanel by drilling hole of suitable , size, using nut, bolts and washers of suitable size as reqd at the site complete all as specified and directed by Engr-in-Charge. Make: Luker Catpart No LFLSL100NSG or equivalent in Havells/ Phillips/ Bajaj 21 S & F in replacement of 150 watts flood light White/Warm white in colour, powder coated and water proof pressure die cast aluminium enclosure, with inbuilt electronic drivers and SPD 6 KV and IP 66 protection complete ,Single phase, etc fixing in MS chanel by drilling hole of suitable , size, using nut, bolts and washers of suitable size as reqd at the site complete all as specified and directed by Engr-in-Charge. Make: Luker Catpart No LFLSL150NSG or equivalent in Havells/ Phillips/ Bajaj 22 S & F in replacement of 200 watts flood light White/Warm white in colour, powder coated and water proof pressure die cast aluminium enclosure, with inbuilt electronic drivers and SPD 6 KV and IP 66 protection complete ,Single phase, etc fixing in MS chanel by drilling hole of suitable , size, using nut, bolts and washers of suitable size as reqd at the site complete all as specified and directed by Engr-in-Charge. Make: Luker Catpart No LFLSL200NSG or equivalent in Havells/ Phillips/ Bajaj 23 S & F in replacement of 250 watts flood light White/Warm white in colour, powder coated and water proof pressure die cast aluminium enclosure, with inbuilt electronic drivers and SPD 6 KV and IP 66 protection complete, Single phase, etc fixing in MS chanel by drilling hole of suitable , size, using nut, bolts and washers of suitable size as reqd at the site complete all as specified and directed by Engr-in-Charge. Make: Luker Catpart No LFLSL250NSG or equivalent in Havells/ Phillips/ Bajaj 24 S&F in repair PVC insulated sheathed wire with copper conductor flexible 3 core 1.5 sqmm including suitable size of lugs for looping all as specified and directed by Engineer-in-Charge. 25 S&F in repair PVC insulated sheathed wire with copper conductor flexible 3 core 2.5 sqmm including suitable size of lugs for looping all as specified and directed by Engineer-in-Charge. 26 Supply and fixing of 2 inch width retro reflective tape fixed to Street light Poles with Red/ Yellow / White colour including removing existing damaged reflected strips from pole complete all as specified and directed. 27 M&L for marking of pole numbers on hexagonal/octagonal street light poles with synthetic enamel paint or stickers made out of suitable material of approved shape and size or as per sample provided by Engr-in-charge. 28 Disconnecting/taking down the hexagonal/Hectagonal GI Pole which is titling/leaning by engaging suitable crane or manually and refixing the same with new nut and bolt of suitable size on existing foundation complete all as specified and directed by Engr-in-charge 29 M&L for scrapping down and removing of old deteriorated paint from Post top lantern poles (RCC/GI) /(4 to 6 mtr) height above ground level, preparing surface for painting, applying two coats of black paint upto full height of pole including MS clamps, GI bracket, fitting etc all as directed at site complete as specified and directed by Engr-in Charge. 30 M&L for scrapping down and removing of old deteriorated paint from steel tubular poles LT (07 to 09 Mtr) height above ground level , preparing surface for painting , applying two coats of aluminium paint upto full height of pole including MS clamps, GI bracket, complete all as specified and directed by Engr-in Charge. 31 Supply and Fixing 1x18 watt WW (3000K) LED bollard Integral decorative LED bollard with polycarbonate diffuser and IP 65 protection incl demolition of existing PCC and make suitable PCC for new bollard as per site requirement and fixing arrangements all as directed by Engr- In - Charge. (Note: Excavation and earth work, PCC for foundation and coping shall be measured paid seperately under respective item of this schedule.) Make Luker Catpart No: LOBRD60or equivalent in Havells/ Phillips/ Bajaj 32 Supply and Fix in replacement integral 45 Watt LED post top lantern black/ copper dust painted cast aluminium spigot, spun aluminium canopy with clear acrylic cover and accessories complete with 50 mm OD black powder coated MS pipe not less than .3mtr length with suitable 5 mm thick ms base plate with provn of 04 Nos anchoring bolts complete all as specified and directed.Make Bajaj (ARIAN) Cat No BGCTN 45W LED or equivalent in Havells/ Phillips/ Bajaj 33 Supply and Fix in replacement integral 25 Watt LED post top lantern black/ copper dust painted cast aluminium spigot, spun aluminium canopy with clear acrylic cover and accessorieson on existing GI Pipe of diameter complete all as specified and directed.Make Bajaj (ARIAN) Cat No BGCTN 25W LED or equivalent in Havells/ Phillips/ Bajaj 34 S&F in replacement Circular LED post-top light, 45 watt energy saving, elegantly designed cast aluminium housing and heat sink for thermal management, high efficiency long life LED module aesthetically designed diffuser and reflector to deliver uniform light output, suitable for mounting on existing pole complete all as specified and directed by Engr-In- Charge. Make: Havells Cat part no RINKPT45WLED757PSYMTOPC / Philips BGP161 LED2500/NW PSU 220-240V 7043 IN / Bajaj BGCPNP 45 W LED CW 35 S&F in replacement 36 watt Post top lantern with options of flat and drop diffuser for area light distribution, Cubical contemporary and sleek design, IP66/IK08 degree of protection suitable for mounting on existing pole complete all as specified and directed by Engr-In- Charge. Make: Philips Cat part no BGP400 LED25 L CW PC S1 or equivalent in Havells/ Phillips/ Bajaj 36 S&F in replacement Post-top lantems conical shaped suitable for use with HPSV SON 70W (l or E), HPMV HPL-N 80W/125W, Blended ML-N 160W lamp. Self contained, integral housing (with ballast, capacitor, ignitor etc.) suitable for mounting on existing pole complete all as specified and directed by Engr-In- Charge. Make: Philips Cat part no SPC1061XS0N-I-70WE or equivalent in Havells/ Phillips/ Bajaj 37 Supply and Fix in replacement 12 w LED bush and spike light luminaires in IP 65 enclosure warm white light output, Make: Luker/Wipro/Bajaj/Havells 38 S&F10 W surface mounted LED Bulk Head Luminaire made of die cast aluminium with Polycarbonate cover, IP65 including all acessories all as specified and directed by Engr-in-charge.Make: Jaquar LBLK02X010XC / Halonix HLBH-02-10-CW or equivalent in Havells/ Phillips/ Bajaj/Luker 39 S&F LED lamp 15 watt (white/ warm white in colour) suitable for fixing into exisitng B22 base holder of bollard/ post top light complete all as specified and directed 40 S&F LED lamp 15 watt (white/ warm white in colour) suitable for fixing into exisitng E27 base holder of bollard/ post top light complete all as specified and directed 41 S&F in replacement E27 base holder suitable for existing post top light complete all as specified and directed 42 Supply and errecting in true vertical position steel tubular swaged pole swan neck type single arm 9 mtr long with cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP-31, including painting with anti corrosive black bituminous paint internally complete and externally up to planting depth with and externally exposed portion with Aluminium paint twin coat over a coat of red oxide primer upto 1.5 mtr above ground level all including taking down unsv/ damaged pole all as required at site or directed by Engr-in-charge.(Note: Excavation and earth work, PCC for foundation and coping shall be measured paid seperately under respective item of this schedule.) 43 Supply and fix in replacement of Junction box thermo plast (weather proof) IP 66, on street light poles made out of thermoplastic of size 300mm x 200 mm x 105 mm size with connector for connecting incomming and outgoing of cable including 01 No of MCB DP 06 Amps to control the pole light circuit and MS brackets made out of 32 x 4 mm flats for fixing the box on post complete with nuts, bolts and washers and suitable size of double compression cable glands for incomming, outgoing of cable Complete all as specified and directed by Engr-In-ChargeMake Sintex Cat pat No GSJB-3020 or equivalent in makes given in PS 44 Supply and fix in replacement of Junction box thermo plast (weather proof) IP 66, on flood light poles made out of thermoplastic of size 140mm x 140 mm x 95 mm size with connector for connecting incomming and outgoing of cable including 01 No of MCB SP 6 Amps to control the pole light circuit and MS brackets made out of 32 x 4 mm flats for fixing the box on post complete with nuts, bolts and wahers and suitable size of double compression cable glands for incomming, outgoing of cable Complete all as specified and directed by Engr-In-ChargeMake Sintex Cat pat No GSJB-1414 or equivalent in makes given in PS 45 S&F in replacement of automatic timer switch distribution board, factory assembled in powder coated sheet steel enclosure, comprising of 40 Amps 3 Pole MCB, power contactor and 230V digital time switch for controlling LED street lights/ flood lights, all as specified and directed by Engr-in-charge. Make Indoasian Cat Pat No.TL040DB0/L&T/Legrand 46 Supply and Fix in replacement integral LED aviation light comprising housing with polycarbonate enclosure, aviation light complete all as specified and directed.Make: Bajaj Catpart No: BGAV302LED or equivalent in Havells/Wipro/ Halonix 47 M&L Cutting of branches of tree of various length to keep a clear distance 2 mtr from the Street light pole and depositioning the cut branches upto a distance of 50 mtr away from the LT/HT/ overhead line/ Transformer complete all as spd and directed by engrs in charge.(Note :- Each span between pole to pole shall be measured one job) 48 Supply and fixing 40 mm bore light grade GI pipe for fixing of post top light including painting with anti corrosive black bituminous paint over a coat of red oxide primer including taking down unsv/ damaged pole all as required at site or directed by Engr-in-charge.(Note: Excavation and earth work, PCC for foundation and coping shall be measured paid seperately under respective item of this schedule.) 49 S&F Tricolour LED Strip light IP 65, with colours Saffron-White-Green of length not less than 18 mtr incl power supply connector, Connector pin, and End cap as per site requirement for fixing at Street light poles complete all as specified and directed. Make : Havells Cat part No FLEXISTRIPTRICAROPE120D18MSTRIPIP65V2 or equivalent in Wipro/ Bajaj/Philips 50 Dismantling/ taking down the pole upto 16/21 metre height of high mast light by engaging suitable crane and repairing the same by replacing the unserviceable top pully of pole and other part such as winch motor, steel wire, power cable and servicing, toping of oil and greasing the gear wheel assembly and hoisting, refixing and connecting up complete all as directed by Engr in charge. Note : a) The repair of light fittings and light fitting spares will be measured and paid separately.b) Spares such as steel wire, motor, power cable etc will be measured and paid separately. c) The entire work shall be carried out with well experienced workers and any damage to the highmast pole or any acessories due to negligience will be replaced by the contractor free of cost.d) Minor spares such as screws, bolt/nuts, grease etc shall provided by the contractor without any extra cost over and above the quoted rate. 51 S&F in replacement of stainless steel rope twisted of size10mm/6 mm dia with necessary connections proper binding on both sides from bottom drum mast top connecting hook including taking down old unsv one complete all as specified and directed by Engr-In-Charge 52 M & L for gear box oil of grade EP 90/140 in standard packed/sealed container including drain out old gear box and filling up new gear box oil complete all as specified and directed Make : HP/Servo/valvoline 53 Disconnecting electric connection and taking down carefully Fractional motor from highmast housing of any type and capacity as removing the burnt winding of motor and rewinding with super enameled copper winding wire of suitable gauge or of matching size to the exisiting wires including all insulating material such as insulation paper sleeve, tape, varnishing etc and reassembling, testing, transporting back to site and refixing to original position all as directed by Engineer-in-charge. 54 Supply, lay, test and commissioning UG cable LT 1100 volt grade heavy duty XLPE insulated armoured with copper stranded conductor complete laid in trenches/fixed to poles /drawn through pipes with suitable size cable glands crimping type cable lugs etc all as specified and directed of size 16 sq mm 4 core, including taking down old unserviceable cable. Make Polycab/Havells/Gloster 55 All as item no 54 above but 10 sq mm 4 core 56 All as item no 54 above but 10 sq mm 2 core 57 All as item no 54 above but 6 sq mm 2 core 58 Supply,laying, testing and commissionnig of LT cables 1100 volts grade, XLPE insulated and PVC sheathed, armoured, with multi stranded aluminum conductor, heavy duty conforming to IS - 1554 part-I, including cable glands, crimping type cable lugs in LT panel / MCCB in bldg etc to suit the cable laid in trenches/fixed to poles/drawn through pipes complete of sizes 35 Sqmm 3.5 core. 59 All as item no 58 above but 25 sq mm 3.5 core complete all as directed 60 All as item no 58 above but 16 sq mm 4 core complete all as directed 61 All as item no 58 above but 10 sq mm 4 core complete all as directed 62 All as item no 58 above but 10 sq mm 2 core complete all as directed 63 All as item no 58 above but 6 sq mm 2 core complete all as directed 64 M&L for bringing Cable testing van (Fault Finder) for detecting the location of fault in the LT UG cable 1.1 KV of any size complete all as specified and as directed 65 M&L in replacement for heat shrinkable Straight through jointing kit for LT 1.1 KV XLPE cables 16 to 35 Sqmm 3.5/4 core including all accessories required. Make :- Denson/ M Seal /3 M 66 M&L in replacement for heat shrinkable Straight through jointing kit for LT 1.1 KV XLPE cables 6 to 10 Sqmm 2/4 core including all accessories required. Make :- Denson/ M Seal /3 M 67 M&L for plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in foundations of poles complete all as specified and directed by Engr-in-charge 68 M&L for plain cement concrete 1:3:6 type C-1 (40 mm graded aggregate) Cement concrete in foundations, filling and mass concrete complete all as specifed. 69 M&L PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in coping of pole including form work and demolition of existing coping complete all as specifed and directed by Engr-in-charge. 70 Excavation in trenches in hard/dense soil n exc 1.5m wide and n.exc 1.5m in depth and getting out complete all as specified and directed by Engr-in-charge 71 Excavation in trenches in soft/dis integrated rock n exc 1.5m wide and n.exc 1.5m in depth and getting out complete all as specified and directed by Engr-in-charge. 72 Returning filling in including spreading leveling watering and well ramming in layers n.exc 25 cm complete all as specified and directed by Engr-in-charge. 73 Removing excavated surplus soil to a distance n exc 50 m and depositing where directed at a level n exc 1.5 mtr above starting point all as specified and directed by Engr-in-charge. 74 Supply and laying 77 mm outer dia, double walled corrugated (DWC) HDPE duct pipe conforming to IS-14930 Pt-II with antirodent and non flame propogating properties of approved colour complete with fittings for cable protection complete all as specified and as directed. 75 Material and labour for cutting of existing road/ hard standing by providing suitable T&P to make suitable size bore for fixing 80/50 mm dia pipe in road crossing etc. including the cost of making good the disturbed surface and matching with existing (Chequered tiles/Road/PCC) complete all as specified and directed by Engr-In-Charge 76 Supply and laying 80 mm bore light grade GI pipe fixed to walls / poles or laid in trenches, road crossing etc, for protection of under ground cable including sealing ends with hessian cloth impregnated with bituminous compound in ground and with suitable clamps, bolt/nuts etc for fixing on walls, poles etc. complete all as specified and directed. 77 All as per item No 76 above but 50 mm bore 78 M&L for demoliton of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar all as specified and directed. 79 M&L for precast coloured, chequered cement concrete tiles, glossy finish of size 300 x 300mm x 25mm thick, conforming to IS-1237 (2006) set jointed and pointed in neat cement slurry in floor laid over and including 20mm thickscreedbed in CM (1:6) complete all as specified and directed. 80 Supply and Fix in replacement of MCCB 125 Amps, 4 Pole, 415V complete all as specified and directed by Engr-in-Charge. Make - L&T DU125D or equivalent in Siemens/Schneider/ABB 81 S&F in replacement of Exit Light, self contained 6W luminarie type, U21 complete with flush mounting frame, sign label, LED & battery and with double side label EXIT complete all as specified and as directed. Make: Prolite or equivalent as approved by GE 82 S&F in replacement of Emergency Exit Beam Light LED type with twin Beam and backup upto 3 hrs complete all as specified and as directed. Make: Prolite or equivalent as approved by GE 83 Attending urgent complaints of Operation Theatre Shadowless type Lights provided in all OTs room of new CH for direct/ reflection free illumination with dual control panel and two domes LED light with various capacity of Make - Dr Mach including replacement of accessories of OT lights. Fault may be due to various switchgear defect, overload, short circuit, earth fault, neutral fault, over heating, high voltage or any other fault not mentioned to be rectified immediately by OEM of respective make as per site including replacement of defective & worn out parts by new spares as directed by engineer-in Charge. (Note : - 1. Spares will be measured and paid separately ) 84 S&F in replacement Power Supply unit for OT Light of Dr. Mach (LED 3 SC) and testing for its functional state complete all as directed by Engr-in-charge. Make- Dr. Mach or equivalent. 85 S&F in replacement Display unit for OT Light of Dr. Mach (LED 3 SC) and testing for its functional state complete all as directed by Engr-in-charge. Make- Dr. Mach or equivalent. 86 S&F in replacement Sterilizable handle for OT Light of Dr. Mach (LED 3 SC) and testing for its functionalstate complete all as directed by Engr-in-charge. Make- Dr. Mach or equivalent. 87 S&F in replacement wiring kit for OT Light of Dr. Mach (LED 3 SC) and testing for its functionalstate complete all as directed by Engr-in-charge. Make- Dr. Mach or equivalent. 88 S&F in replacement Cluster board for OT Light of Dr. Mach (LED 3 SC) and testing for its functionalstate complete all as directed by Engr-in-charge. Make- Dr. Mach or equivalent. 89 Supply, installation and commissioning of ESE Lightning Arrester including installation of LA on 5m long mast with guy rope,Test Link Box (MS Powder coated box size of 300mm x 120mm x 100 mm), ESE LA Counter, Guy Rope with connected accessories. The ESE LA should be installed on the highest location of the buildings and necessary scafolding work or protective arrangement should be made by contractor while execution of work complete all as specified and directed. Make : U-Protec Earting Pvt Ltd or equivalent in Ashlok Earthings/JEF technology/Tirumala 90 Supply and fixing 70 Sqmm single core multistranded Copper Cable, 1100 Volts PVC insulated on wall / roof of building with clamps for connection of ESE lightening arrestor to earthing terminal with copper lugs, SS nut bolts and washers accessories as per site requirement complete all as specified and directed. 91 Test point terminal block made of gun metal or phosphorus bronze size 75X75X25mm drilled and screwed including 3 Nos 8mm dia 25mm long hex head screw complete all as specified and directed. 92 Supply and fix 32x6 mm galvanised iron strip earth continuity conductor on wall /floor and connected to equipment including nut & bolts of suitable size complete all as specified & directed by Engr-In-Charge. 93 M&L for maintenance free grounding Solution set earthing comprising of 17.2 mm pure copper earthing rod, 3m long, Copper terminal size of 40x6mm with 2 Nos M8 holes for termination. Electrode must be tested for a short circuit test of minimum 40 KA at CPRI/NABL. The earthing electrode will be placed in the ground after a bore is drilled to the depth of 3.5 Mtr. The bore drilling will be done with the help of a Pneumatic boring machine, 50 Kgs BFC will be placed in the bore to cover the earthing rod from all sides. BFC will be poured in Slurry form in a properly mixed condition. The Earth pit cover Square 300x300x240 mm to be provided to cover the Earth Pit and shall be made of reinforced FRP and should be capable of carrying the weight of 5 Tons. Make : U-PROTEC earthing Pvt Ltd or equivalent in Ashlok safe earthings electrode Ltd /JEF technology/Tirumala NOTE :- (a) Rates of boring 3.5 Mtr for earth electrode, Copper strip 25x3 mm upto 7.5 Mtr from earth electrode is deemed to be included in the quoted rate. (b) On testing, after completion, if the earth resistance <5 ohms is not obtained, earthing will be rejuvenated at no extra cost till the desired earth resistance is obtained. 94 S & F illuminated display board of size (1.28 x 0.2 x 0.9) Mtr (L x B xH)with Flexof Light Blue (MES Colour),Colour of letters shall be white, outerside fabrication bordered with Aluminium angle Frame of size (20 x 20) mm x 3mm thick, innerside fabricated with 12mm MS square bar and aluminium sheet for top, bottom, back side, left side and right side of the display board, 50mm dia GI Pipe medium grade shall be fixed both side of board with 2 Nos 30 mm x 4mm thick MS flat of 0.2 Mtr length welded to GI pipe and nut bolt and washer with display boardnot less than 2.5 Mtr and PCC 1:4:8 for foundation including all internal wirings and illuminated with LED 40 W Tubelightfitting 01 No, SMC/FRP Junction Box 140mm x 140mm x 95mm inner dimension make Sintex/National, the board must be openable from back side for maintenance of tube light, control wiring etc. Make : Bajaj Cat Part No BCLAB 20W /Wipro/Havells including its fixing arrangement and written Letters in capital not less than 10 letters and more than 40 letters, size of letters proportion with overall size of board complete all as specifiedand as directed. Note : (i) Before manufacturing Boards drawing and design of Board including colour of board shall be approved by Engr-in-charge.(ii) Each board display name shall be given seperately. 95 M&L for fabrication, supplying, fixing and commissioning of informatory boards at E/M installation to display the technical details as provided by Engr-in-Charge of various installtions made out of 3 mm thick aluminium composite panel (ACP) fully covered with white/green/blue (as directed) Retro refective sheeting of nikkalite Brand Ultralite (UL) grade with using pressure sensitive adhesive and Retro Reflective cut out border and message in the sensitive adhesive, size of the board of required size to be fixed on wall incl proper fixing arrangement complete all as specified and directed.Note :- (a) Before fabriction of the board, the contractor has to produce a paper printout detailing all dimensions and matter to be displayed so as to get it inspected and passed by Engr-in-Charge.(b) Matter to be displayed, colour of the ACP sheet and colour of Retro Reflective sheet will be as specified and directed by Engr-in-Charge.(c) The quoted rate is deemed to be inclusive of cost of the labour and materials required for fixing of the informatory board at the location as specified and Engr-in-Charge.
