Tender For Provision Of 01 X Lbw And 03 X Minor Works In The Area Of Age B/R-I Under Ge Gwalior.; 1 Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations etc or for shafts, well cess pits, manholes, pier holes, etc but not exceeding 10 Sqm on planand getting out inany type ofsoil complete all as specified and directed. 2 Removing excavated materialn.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed. 3 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in loose/soft soil complete all as specified and directed. 4 Moorum/red bajri filling in floors or pavings, laid in layers n.exc 15 cm thick, spread, levelled and rammed including watering as required complete all as specified and directed. 5 M&L for Plain cement concrete (1:4:8) type D2 (using 40 mm graded stone aggregate) as in foundations / mass concrete complete all as specified and directed. 6 M&L forreinforced cement concrete Design mix M-25 (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, base for coloumns and mass concreteetc complete all as specified and directed. 7 M&L forreinforced cement concrete Design mix M-25(using 20 mm graded stone aggregate) as incoloumns, pillars, piers, posts and struts etc complete all as specified and directed. 8 M&L forreinforced cement concrete Design mix M-25 (using 20 mm graded stone aggregate) as in chajjas,etc complete all as specified and directed. 9 M&L forreinforced cement concrete Design mix M-25 (using 20 mm graded stone aggregate) as in Roof beam, lintel band, cantilevers bressummers, lintels over 1.5m spanetc complete all as specified and directed. 10 M&L forreinforced cement concrete Design mix M-25(using 20 mm graded stone aggregate) as in slab supported on walls, beams, columns in floor, roof, landing complete all as specified and directed. 11 M&L for Formwork to sides of concrete, in foundations, footings, base of columns & plinth beams, etc in flat for rough finshed surfaces of concrete complete all as specified and directed. 12 Formwork to Columns, square/rectangular, rough finish surfaces of concrete complete all as specified and directed. 13 M&L for formwork to soffits of suspended slab such as roof slab, floor slabs, landing and similar work not exc 200mm thick complete all as specified and directed. 14 M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills concrete railings, opening in concrete walls, floor and roofs slab n.exc 20 cm wide and sides of RCC/PCC bands in walls, exc 10cm and n.exc 20cm wide complete all as specified and directed. 15 M&L for formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed. 16 M&L for formworkto sides and soffits of floor or roof beams, beam haunchings, lintel bands, cantilevers shelves incldng supports, overhangs, etc complete all as specified and directed. 17 M&Lfor mild steel TMT bars, 10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed. 18 M&Lfor mild steel TMT bars 6 mmto 8 mm diaover cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed. 19 M&Lfor mild steel TMT bars 5 mm and over uptoand including 10 mm dia, as in stirrups, spacers,and binders, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. 20 M&L for hard core of broken stone boulder of gage n.exc 63mm deposited, spread and levelled in layers n.exc 15 cm thick watered and rammed to a true surfaces complete all as specified and directed. 21 M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate, 75 mm thick finished even and smooth without using extra cement as in plinth protection including forming of joints 10mm wide and 75mm deep and joint filled with bitumin and sand mixture in 1:1 ratio complete all as specified and directed. 22 M&L forPCC(1:4:8) type D-2 (using40 mm graded stone aggregate) 75 mm thick,as in sub base for floor, finished even and rough complete all as specified and directed. 23 M&L for 25 mm thick cement concrete (1:2:4) Type B-0 (using 12.5 mm graded stone aggregate) as in levelling course complete all as specified and directed. 24 M&L for non skid ceramic colouredtiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles, over screed bed or bedding layer 15 mm thick of cement mortar 1:4 complete all as specified and directed. 25 M&L forglazed ceramic coloured tiles in vertical surface 350mm x 250mm x 7mm/ 450 x 300 x 7 mm thick set and jointed in neat cement slurry and pointed inwhite or colour cement to match, aid over and including rendering 10 mm thick on fair facesbrick work or concrete surface in cement plaster 1:4 complete all as specified and directed. 26 M&L for Brick work with sub class ‘B’bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed. 27 Brick work with sub class `B bricks straight or curved on plan exc 6m mean radius, built in CM 1:4, in half brick walls complete all as specified and directed. 28 M&L for 15mm thick rendering on brick or stone/concrete any surfaces in cement mortar 1: 4 on mixed with Liquid WPCby weight of cement, surface finished even and smooth without using extra cement complete all as specified and directed.Note : WPC shall be measured & paid seperately. 29 Supply only integral liquid water proofing compound (ISI marked) complete all as specified anddirected. 30 M&L for 10 mm thick rendering in cement mortaron fair faces of brick work or concrete surfaces in cement mortar (1:6) and surface finishedeven and smooth, complete all as specified and directed. 31 M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed. 32 M&L for applying two coats of cement base paint, including preparation of newly plastered surface of walls complete all as specified and directed. 33 M&L for Preparing new plastered surfaces of wall and applying three coats of white wash complete all as specified and directed. 34 M&L for Preparing new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. 35 S&F solid PVC doors frames of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, in opening as per specification and drawing as specified in clause 8B-1 to 8-B-10 on page 133 to 138 and page 146 to 153 of SSR -2004 part-II complete all as specified and directed. 36 S&F factory made solid panel PVC door shutters 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails, MS frame shall be covered withheat moulded plain colour PVC`C` channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles ad plain colour PVC sheet for top rail, lock rail & bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stile & rails suitable PVC sheet beading and jointed together with solvent cement and fixing in the frame complete all as specified and shown on drawings of SSRPart-II . 37 S&F Box Type steel windows, Ventilator with side hung shutters (double shutters for glass and gauge) joined together with and including grills using 12 mm square bars @ 10 mm c/c as per TD No CEBZ/TD/14/2011, Sheet no -1/7 to 7/7 Including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welded complete all as specified and directed. 38 S&F for 3mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding0.5 sqm in each pane complete all as specified and directed. 39 S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 40 S&F for Butthinges, 100 mm size, extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed complete all as specified and directed. 41 S&F forAluminium handles, cast type anodised of Size 150 mm complete all as specified and directed. 42 S&F for 150 mm long aluminum anodized barrel tower bolts of extruded section and fixed complete all as specified and directed. 43 M&L, preparation or new steel and iron surfaces of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. 44 S&F for 75 mm diaPVC (SWR) pipes single socketedin any length with rubber ring joints laid in trenches or in floor complete all as specified and directed. 45 S&F for 110 mm diaPVC (SWR) pipes single socketedin any length with rubber ring jointslaid in trenches or in floor complete all as specified and directed. 46 S&F for 110 mm diaPVC (SWR ) pipes single socketedin any length with rubber ring joints fixed on wall with necessary clampcomplete all as specified and directed. 47 S&F for PVC (SWR) bends any radius, 75 mm bore, provided with access door complete all as specified and directed. 48 S&F for PVC (SWR) bends any radius, 110 mm bore, provided with access door complete all as specified and directed. 49 S&F for 75 mm bore, PVC (SWR) junction single (single T), equal or unequal,provided with access door complete all as specified and directed. 50 S&F for 110mm bore, PVC (SWR) junction single (single T), equal or unequal, provided with access door complete all as specified and directed. 51 S&F for 110mm dia PVC(SWR) vent cowl, complete all as specified and directed. 52 M&L for PVC floor trap, plain with grating including jointing to waste pipe with solvent cement dia of outlet 75mm complete all as specified and directed. 53 M&L for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. 54 S&F for 1000 ltr capacity rotational moulded polythene water storage tank two layers ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed. 55 S&F for Ball brass valves high pressure with polythene float and flynut complete screwed for iron pipe of 20mm bore of brass ferrule complete all as specified and directed. 56 Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fixed to walls and ceiling or laid in floor etc complete all as specified and directed. 57 Supplying and laying of 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fixed to walls and ceiling or laid in floor etc complete all as specified and directed. 58 S&F for 25mm stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union fixed complete all as specified and directed. 59 S&F for 600 x 450 mm size bevelled edge Mirror of selected quality glass mounted on 6 mm thick commercial plywood water proof with aluminium frame all around and fixed on wall with wooden/Plastic cleats and brass chromium plated screws complete all as specified and directed. 60 S&F tublar towel rail 20mm dia D type 60 cm long between flange Aluminium anodised complete all as specified and directed. 61 S&F for PVC connection of 600 mm length complete all as specified and directed. 62 S&F for bib taps fency type 15 mm caste copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe and fixedcomplete all as specified and directed. 63 S&F for stop cock fency type 15 mm caste copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe and fixedcomplete all as specified and directed. 64 S&F for vitreous china wash hand basin white flat back size 550 x 400mm excluding taps waste chain and plug and porcelain stopper but including brackets complete all as specified and directed. 65 S&F for central hole basin mixture caste copper alloy with capstan heads chromium plated screwed down high pressure without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixedcomplete all as specified and directed. 66 S&F for waste fitting for wash basins and sinks with inlet and outlet, screwed for pipe or connections and with one cleaning cap, 32mm bore complete all as specified and directed. 67 S&F for vitreous China Urinal, full stall type, white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed. 68 S&F for urinal spreader of cast copper alloy,fancy type with chromium plated, screwed both ends for iron pipe or for unions, complete all as directed fixing with 15 mm dia pipe (Minimum weight 60gms). 69 S&F for vitreous china urinal partition white of size 310x700 mm terminating about 40 cm above floor line including brackets, clamps and necessary items to fix on wall complete all as specified and directed. 70 S&F for viterous china wash down water closet pan (pedestal pattern) or wall mounted white fixing bolts, excluding flushing cistern and flush pipe including Seat cover, connection to drain and to flushing pipe syphonage pipe etc and mild steel chromium plated or aluminised hinges device & CP Jet complete all as specified and directed. 71 S&F for PVC valveless syphonic action type flushing cistern low level white with inlet ball valve, float end handle handle including bracket complete of capacity 10 litres, complete all as specified and directed. 72 S&F for Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible and ABS wall hoock including making connection and fixing in position complete all as specfied and directed. 73 S&F for 32 mm bore PVC waste pipe and 65 cm long flexible complete all as specified and directed. 74 S&F for Soap dish of CP fixed with pvc rawal plugs and screw, complete all as specified and directed. 75 S&F for grating doom 125mm dia with waste hole of Chromium plated (Minimum weight 40gms to Nahani traps etc) complete all as specified and directed. 76 S&F for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm longcomplete all as specified and directed. 77 M&L for 10mm thick screed on top of roof surfaces of any description in cement mortar 1:4mixed with liquid WPC @ 0.4% by weight of cement, surface finished even and smooth withoutusing extra cement complete all as specified and directed.Note : WPC shall be measured & paid seperately. 78 M&L for bitumenous based primer conforming to IS-3384-1965 @ 0.40 Kg / Sqm including preparation of roof surface complete all as specified and directed. 79 M&L for APP based polymeric membrane minimumweighing 3.0 kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by torch application method complete all as specified and directed. 80 M&L for after laying the membrane apply coat of bituminouse aluminium paint @ 200 gm/Sqm (minimum) in two coats complete all as specified and as directed. 81 M&L for cement concrete (1:3:6) type C2 using 40mm graded stone aggregate in bed to drain pipe including packing under and hunching against the sides of pipes after they are laid and tested complete for pipe size of 150mm bore complete all as specified and directed. 82 M&L for 150 mm bore Reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and directed. 83 M&L for providing cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) in surfaces channels drains and benching including formwork and finishing fair and smooth using extra cement (forming fair finished channel shall be measured and paid for separately) complete all as specified and directed. 84 M&L for precast cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in cover slabs for man holes and set in CM 1:4 including necessary from work complete all as specified and directed.Note: Reinforcement and form work shall be measured and paid separately) 85 Cutting into existing manholes for connecting new 150mm diadrains pipe, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) smooth finished, and reforming benching as required complete all as specified and directed. 86 M&L, concealed point wiring with PVC insulated and unsheathedelectric cable 1100 volts grade single core FRLSH confirming to IS 694:2010 having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area (ISI marked with valid CML No) drawn in and including concealed non metallic rigid PVC conduit medium grade (ISI marked with valid CML No)not less than 20 mm diawith all fitting and fixing accessories and1.5 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to common earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxesfactory made for mounting switch, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint insidefor mounting switches sockets etc complete all as specified and directed. 87 One light point controlled by one switch. 88 One Exhaust fan point controlled by one switch. 89 One 3 pin/5 pin switch socket outlet, 5 Amps on independent board. 90 Description all as per item No86 here in before but point wiring with 2.5 sqmm FRLSH H confirming to IS 694:2010, multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 2.5 sqmm FRLSH PVC insulated multi strand copper conductor cable as continous earth wire complete all as specified and directed. 91 S&F Modular switch 1 way 6 A, 1 module complete all as specified and directed. 92 S&F Modular Socket, 6A - 2/3 pin combined 2 module ,complete all as specified and directed. 93 S&F Modular switch 1 way 16 A, 1 module complete all as specified and directed. 94 S&F Modular Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed. 95 S&F Modular ceiling rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed. 96 S&FLamp holder with metal ring, PVC/Polycarbonate type with back plate suitable for batten fittings ISI Marked complete all as specified and directed. 97 S&F Decorative ultra slim LED Tubelight fitting of LEDwith extruded polycarbonate, enviormental friendly energy efficient ready to use, 10 watt, 6500k as per requiredfitting , including reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor forelectrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed. 98 Removal of excavated materials (soil) exceeding 250 meters but not500 meters and deposting where directed at a level not exceeding1.5 meters above the starting point, complete all as specified and directed. 99 M&L for 150mm dia internal bore Salt-glazed stoneware drain pipes laid in trenches and jointedcomplete all as specified specified and directed. 100 M&L for brick work with sub class ‘B’ brick old size brick, straight or curved on plan exceeding 6 meters mean radius built in CM (1:4) complete all as specified and directed. 101 M&L for cement concrete (1:2:4) type B-1 using 20mm graded agrregate in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth course, string course, lacing course, parapets and railingsupto 60cm in height, coping, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering slightly rounded or chamfered angle and throating complete all as specified and directed. 102 Construction of Septic tanks including excavation, in any type of soil, foundation in PCC 1:2:4 type B-2 (using 20mm graded stone aggregate) brick work in CM 1:4, RCC M-20 (Nominal Mixed) (with and including reinforcement), Slab covers including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame Vent pipe shaft and sludge chambers etc complete for 50 users complete all as specified and directed and shown in drawing No. CEBZ/TD/76/2011Sheet 1/4 to 4/4. 103 Construction of Soakage wells including excavation in any type of soil, foundation in PCC 1:3:6, wells of honey combed and solid in M-20(Nominal Mixed) Concrete type C-2 (using 20mm graded stone aggregate), including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-20/ Brick Masonry/ filling with brick bats, complete of size 1.8 m in dia and 4.50m in deep (effective depth) complete all as specified and directed as shown in drawing No.CEBZ/TD/76/2011 Sheet 1/2 & 2/2. 104 M&L for cement concrete (1:3:6) in surface channels and drains type C-2 (using 40mm graded stone aggregate) complete all as specified and directed. 105 M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi-tred/stopped ends etc complete all as specified and directed.(Note : Inner girth shall only be measured) 106 Supply,installation, testing and commisioning of smokeless waste incinerator machine capapcity 5-25 kg per batch, fully automatic high temparature combustion chamber for complete waste destruction with 99% buring efficiency with build in emission control as per CPCB NORMS electric incinerator machine including covered stainless steel dustbin for campatible for destruction of senitary napkins, diaper,having below technical specification- 1 Capacity- 25kg batch /hours 2 Model-Fully automatic3Campatible for senitary napkins, diaper.4 Dimension-2000 X 750 X 1350 mm5 Power supply -230 volt AC 50 HZ 32 AMP6 Stand mount7 Temparature of primary chamber-850 Degree celcius8 Temparature of Secondry chamber-1100 Degree celcius9 Cover stainless steel dustbincapacity -25 ltr 107 Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable(Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area 10 Sqmm 2 Core all as specified and directed.all as specified and directed. 108 S & F sheet metal box Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 32 amp. 109 Material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with aproved colour, design & attern as in foothpath, parks, lawns, drive ways or light traffic arking etc. of required strenght, thickness & size / shape, made by table vibrating method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra cement complete all as specified and directed. 110 M& L for Brick work with sub-class `B bricks, straight or curved on planto anyradius, in half brick workbuilt in cement mortar 1:4 complete all as specified and as directed. 111 M&L for 15 mm thick rendering in cement mortar (1:6) on brick or concrete surfaces finished even and smooth without using extra cementcomplete all as specified and as directed. 112 S&F Pre painted galvalum sheet 0.50 mm thick havingaluminum zinc coating 150 gsm/ sqm steel sheetany colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws complete all asdirected 113 S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates confirming to Fe-290 ( Gde E-165) complete all as specified and directed 114 Sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete. 115 Supplying and laying un reinforced precast concrete cable coverClass LV, Type I, flat size 250mm x 150mm x 40mm complete all as specified and directed. 116 M&L for angle iron posts and struts in fencing including cutting tops to shape (swan neck) or as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work including 40x6mm flat iron for holding chain link fencing conforming to Fe-290 Gde E-165 all as specified and as directed. 117 Mild steel round bars Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 118 M&L, preparation or new steel and iron surfaces of any description and applying a coat of red oxide primer complete all as specified and directed. 119 Fixing only galvanised chain link fencing of 4mm dia GI wire including line wire standards rails straining bolts etc including provision of binding wire and mesh size as per direction of GE Gwalior & complete all as specified and as directed. 120 Supply only galvanised chain link fencing of 4mm dia GI wire including line wire standards rails straining bolts etc including provision of binding wire and mesh size as per direction of GE Gwalior & complete all as specified and as directed. 121 M&L for Galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm specing and staining and fixing to any type of standard rails including securing or lying at crossing with and provn of MS galvanised pins etc as directed. 122 Mild steel screw bolts 10mm dia and 5cm long (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends,each screwed end to be fitted with washers and one hexagonal or square nut,complete all as specified.
