Tender For Repair And Painting Of Steel Furniture Under Ge Guwahati, guwahati-Assam

Tender For Repair And Painting Of Steel Furniture Under Ge Guwahati; 1 ALMIRAH LARGE STEEL (DRG NO FD-1031,FD/E6/MAP/18):-` 2 M&L for removing dents and bends and welding wherever required for Almirah Large Steel, Scrapping old painted surfaces and removing existing paint on surfaces with chemical/aerosal spray.Preperation of surfaces after applying putty and red oxide primer and spray painting of almirah large steel complete(inside and outside) with a coat of synthetic enamel paint.Colour :- Olive Green or any other colour or combination of colour as directed.Note :- Almirah as a whole shall be measured as one unit. 3 S& F in replacement of new locks 7 lever Godrej pattern or equivalent best quality as approved with duplicate stainless steel key complete. 4 S& F in replacement of 3 way locking device best quality complete. 5 M&L for removing old /unserviceable legs and S & F of new Legs made out of 1 mm MS sheet to the required shape as per drawing duly welded at the bottom of the frame by removing old rusted unserviceable leg and applying two coats of olive green paint (1st grade quality) over a coat of red oxide primer by spray machine after preparation of surfaces to match the existing surfaces as directed. 6 S&F of 100 mm Steel Chromium Plated Handle for Almirah alongwith nuts and washer complete. 7 S& F in replacement of butt hinges best quality with duplicate stainless steel key complete. 8 M&L for removing old /unserviceable Shelf and S & F of new shelf made out of 1 mm MS sheet to the required shape as per drawing and applying two coats of olive green synthetic enamel paint (1st grade quality) over a coat of red oxide primer by spray machine after preparation of surfaces to match the existing surfaces complete all as directed. 9 M&L for removing old /unserviceable Door and S & F of new Door made out of 1 mm MS sheet to the required shape as per drawing and applying two coats of olive green synthetic enamel paint (1st grade quality) over a coat of red oxide primer by spray machine after preparation of surfaces to match the existing complete all as directed. 10 ALMIRAH MEDIUM/SMALL STEEL (DRG NO FD 350/1032/1034/104(M)):- 11 M&L for removing dents and bends and welding wherever required for Almirah steel, Scrapping old painted surfaces and removing existing paint on surfaces with chemical/aerosal spray including preperation of surfaces after applying puttyand red oxide primer and spray painting of almirah Medium steel complete(inside and outside) with a coat of synthetic enamel paint as approved by Engr-in-charge Colour :- Olive Green or any other colour or combination of colour as directed.Note :- Almirah as a whole shall be measured as one unit. 12 S& F in replacement of old lock with new one by providing new 7 lever lock ofGodrej pattern of best quality as approved with duplicate stainless steel key complete. 13 S& F in replacement of 3 way locking device best quality as approved. 14 M&L for removing old /unserviceable legs and S & F of new Legs made out of 1 mm MS sheet to the required shape as per drawing duly welded at the bottom of the frame by removing old rusted unserviceable leg and applying two coats of olive green paint (1st grade quality) over a coat of red oxide primer by spray machine after preparation of surfaces to match the existing surfaces complete. 15 S&F of 100 mm Steel Chromium Plated Handle for Almirah alongwith nuts and washer by removing old one complete all as directed. 16 S& F in replacement of butt hinges best quality complete. 17 M&L for removing old /unserviceable Shelf and S & F of new shelf made out of 1 mm MS sheet to the required shape as per drawing and applying two coats of olive green synthetic enamel paint (1st grade quality) over a coat of red oxide primer by spray machine after preparation of surfaces to match the existing surfaces complete all as directed. 18 M&L for removing old /unserviceable Door and S & F of new Door made out of 1 mm MS sheet to the required shape as per drawing and applying two coats of olive green synthetic enamel paint (1st grade quality) over a coat of red oxide primer by spray machine after preparation of surfaces to match the existing surfaces as directed. 19 REPAIR TO LOCKER STEEL (DRG NO FD 257/1029):- 20 M&L for removing dents and bends and welding wherever required for LockerSteel and scrapping old painted surfaces, removing existing paint on surfaces with chemical/aerosal spray, Preperation of surfaces after applying putty and red oxide primer and spray painting of Locker steel complete (inside and outside) with a coat of synthetic enamel paint complete.Colour :- Olive Green or any other colour or combination of colour as directed.Note :- Lockeras a whole shall be measured as one unit. 21 S&F in repair Hasp and staple chromium plated 100 mm long after removing of old unserviceable Hasp and staples complete all as specified on drawing and as directed. 22 S&Fin repair 100mm long steel chromium platedhandle complete. 23 Removing of old unserviceable conduit pipe and S&F of new conduit pipe of same size i.e. Chromium plated steel conduit pipe of 19 mm dia with 1.60mm wall thickness alongwith bracket complete all as specified on drawing and as directed. 24 S& F in replacement of butt hinges complete 25 M&L for removing old /unserviceable Shelf and S & F of new shelf made out of 1 mm MS sheet to the required shape as per drawing and applying two coats of olive green synthetic enamel paint (1st grade quality) over a coat of red oxide primer by spray machine including preparation of surfaces to match the existing complete all as directed. 26 M&L for removing old /unserviceable Door and S & F of new Door made out of 1 mm MS sheet to the required shape as per drawing and applying two coats of olive green synthetic enamel paint (1st grade quality) over a coat of red oxide primer by spray machine including preparation of surfaces to match the existing complete allas directed. 27 M&L for removing old /unserviceable legs and S & F of new Legs made out of 1 mm MS sheet to the required shape as per drawing duly welded at the bottom of the frame by removing old rusted unserviceable leg and applying two coats of olive green synthetic enamel paint (1st grade quality) over a coat of red oxide primer by spray machine after preparation of surfaces to match the existing complete all as directed.Make for Sheet:- Rinl/Sail/Tisco 28 TABLE OFFICE CLERK STEEL (DRG NO FD 381/1004):- 29 M&L for removing dents and bends and welding wherever required for Table office clerk Steel, scrapping old painted surfaces and removing existing paint on surfaces with chemical/aerosal spray including preperation of surfaces after applying putty and red oxide primer and spray painting of Table office clerk steelcomplete(inside and outside) with a coat of synthetic enamel paint complete.Colour :- Olive Green or any other colour or combination of colour as directed.Note :- Tableas a whole shall be measured as one unit. 30 Supply and fix in replacement of new brass locks with duplicate keys best quality complete. 31 Supply and fix in replacement of 18 mm thickpre laminated particle boardexterior grade ISI marked teak face and PVC edging all around complete as specified and as shown on drawing.Make of particle Board:- Eco Board/Bhutan Bd/Novapan/Century Lam 32 M&L for removing old /unserviceable drawer and S & F of new drawer made out of 1 mm MS sheet to the required shape as per drawing and applying two coats of olive green paint (1st grade quality) over a coat of red oxide primer by spray machine after preparation of surfacesas directed. 33 TABLE OFFICE OFFICER STEEL (DRG NO FD 84 (M) /1003 /1002):- 34 M&L for removing dents and bends and welding wherever required for Table office officer Steel incl scrapping old painted surfaces and removing existing paint on surfaces with chemical/aerosal spray over putty and red oxide primer and spray (inside and outside) with a coat of synthetic enamel paint complete all as directed.Colour :- Olive Green or any other colour or combination of colour as directed.Note :- Table as a whole shall be measured as one unit 35 S&F in repair brass lock with duplicate keys of best quality complete 36 Removing old unserviceable Top and supply and S&F ofnew top made out of 18mm thickpre laminated particle board exterior grade ISI marked teak face and PVC edging all around as specified and as shown on drawing. 37 M&L for removing old /unserviceable drawer and S & F of new drawer made out of 1 mm MS sheet to the required shape as per drawing and applying two coats of olive green synthetic enamel paint (1st grade quality) over a coat of red oxide primer by spray machine including preparation of surfacesas complete all asdirected. 38 CHARPOY GIPIPE (FD-220) 39 Removing the existing unserviceable plytop and S& F of new 12 mm thick BWR plywood exterior grade quality including flush headed bolts and nuts with washers for fixing plywood to charpoy and spot welding wherever required. Plywood edges to be smoothened and corners rounded complete as specified and as directed.Note:- Tightening of existing frame after replacement of parts as mentioned in this item included in this item before replacing of plywood. 40 Removing of following existing unserviceable long rail of charpoy carefully and S& F of new long rail including tightening of joints , placing every part in tact as per drawing and as directed. 41 All as per Item 6.02 above but for short rails retrived out of unserviceable/replaced long rails 42 All as per Item 6.03 above but for legs retrived out of unserviceable/replaced shortrails and fixing wherever required for legs 43 6.05 All as per Item 6.02 above but for S & F ofnew 32mm dia GI medium grade 3 way elbow having ISI marked 44 All as per Item 6.02 above but for S & F ofnew5 mm checknutsuitable for GI 32 mm medium grade pipe 45 CHARPOY MS SQ TUBE PLY TOP FD/MAP-II/01 46 Removing of old painted surface and preparing of surface by applying putty and one coat of red oxide after welding wherever required (legs/rails) and applying two coats of synthetic enamel paint black colour to match as per standard drawingand as directed. 47 Removing of old/unserviceable Ply top from Charpoy MS Square Tube & S&F of new 12mm thick BWR plywood of exterior grade and fixing the same with screws 4mm thick alongwith washers as specified including removing existing rubber shoes and S& F of Hard rubber shoes ( 4 Nos) for each charpoy complete all as directed. 48 BED HARD STEEL (FD/E6/MAP/08) 49 Removing of old paint and preparing surface by applying putty and one coat of red oxide afterwelding wherever required(legs/rails) and applying two coats of synthetic enamel paint black colour to match as per standard drawing and as directed. 50 Removing of old/unserviceable Ply top from Bed Hard Steel& S&F of new 12mm thickBWR plywood of exterior grade and fixing the same with screws 4mm thick alongwith washers including S& F of new hard rubber shoes ( 4 Nos ) for each bed after removing the existing ones complete all as directed. 51 REPAIR TO CHAIR WRITING STEEL MAP (FD/E6/MAP/01) 52 M&L for removing the old unserviceable back of Chair Writing Steel & S&F of new back of same size made of 12 mm hot pressed plywood upholstered with fabric and moulded polyurethane foam 50 mm thickness with PVC lipping all around along with welding of of mettallic rail structure where required and shall be fixed to the rail with screws 4mm thick alongwith washers as per sample approved complete all as specified and as directed. 53 M&L for removing the old unserviceable seat of Chair Writing Steel & S&F of new seat of same size made of 12 mm hot pressed plywood upholstered with fabric and moulded polyurethane foam 50 mm thickness with PVC lipping all around along with welding of of mettallic rail structure where required and shall be fixed to the rail with screws 4mm thick alongwith washers as per sample approved complete all as specified and as directed. 54 M&L for removing the old unserviceable handle / armrest of Chair Writing Steel & S&F of new handle of same size made of black integral skin polyurethane with reinforced MS insert and shall be back fixed to the rail with screws 4mm thick alongwith washers as per sample approved complete all as specified and as directed. 55 M&L for removing the old unserviceable Cantilever type MS tubular frame of Chair Writing Steel & S&F of new frame of same size and shall be back fixed to the Chair writing steel as per sample approved complete all as specified and as directed. 56 CHAIR VERANDAH (FD -19 M/ FD-359) 57 Re-canning of chair verandah after removing the existing cane and to carry out necessary welding and repairs wherever required and painted with two coats of synthetic enamel paint over a coat of primer and weaving with new white plastic cane of approved quality with 3.5 to 4mm wide half round type for seat and back and fixing 04 Nos of hard rubber shoe/PVC shoes for legs of 20 mm dia after removal of old existing /unserviceable shoes complete all as shown on drawing and as directed. Note:- Cane shall be of plastic strips of superior quality, type -I HDPE white or cream colour of uniform width conforming to IS-5387 Make of Cane :- M/S Maharasthra Plastic Industries /India Plastic/ Shah & Shah /Premier 58 BOOK CASE STEEL LARGE (FD-1028) 59 M&L for denting / removing bends and removing the existing paintby applying chemical/aerosal spray and preparing the surface by applying putty and primer to bring out an even surface and applying a coat of synthetic enamel paint of olive green colour or any other colour/combination to Book Case Steel Large complete as specified and directed. 60 S&F in replacement of 5 mm thick sheet glass and fitting with 1 mm MS sheet channel with roller for sliding doors complete all as specified in drwaing and as directed. 61 S&F in repair of 100 mm steel chromium plated handle complete all as shown on drawing and as directed. 62 TEAPOY VARANDAH (FD-255, FD/E6/MAP/17) 63 Removing old unserviceable Top andS&F ofnew top made out of pre laminated particle board 18 mm exterior grade ISI marked teak face and PVC edging all around as specified and as shown on drawing. 64 M&L for removing existing paint and preparing the surface after applying putty and a coat of primer and Painting ofTeapoy verandah with two coats of synthetic enamel paint (1st grade quality) white colour with glossy finishby spray machine and Supply and Fix of newhard rubber/PVCshoes after removing existing old/unserviceable shoes complete as specified and shown on drawing and as directed. 65 TRESTLE STORE ROOM IRON FD-1043 66 M&L for removing dents and bends and existing paint and preparing surface by applying putty and a coat of red oxide primer and applying a coat of Synthetic enamel paint of Olive Green colour or any other colour as specified and as directed. 67 TABLESTEEL 900X600X760 MM WITH & W/O DRAWER(DRG NO FD-1007/HFD-2014/FD-1008):- 68 M&L for removing dents and bends and welding wherever required for Table with & without drawer steel, scrapping old painted surfaces and removing existing paint on surfaces with chemical/aerosal spray.Preperation of surfaces after applying puttyand red oxide primer and spray painting of Table with and without drawer steel complete (inside and outside) with a coat of synthetic enamel paint cpmolete all as specified and as directed.Note :- Tableas a whole shall be measured as one unit. 69 S&F in repair of top made of 18 mm thickpre laminated particle boardexterior grade ISI marked teak face and PVC edging all around as specified and as shown on drawing. 70 Supply and fix in repairs of brass locks with duplicate keys best quality complete. 71 CHAIR REVOLVING /COMPUTER MAP (TP, FD/E6/MAP/01) 72 M&L for removing the old unserviceable back of Chair computer & S&F of new back of same size made of 12 mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam 50 mm thickness with PVC lipping all around along with welding of of mettallic rail structure where required and shall be fixed to the rail with screws alongwith washers as per sample approved as specified in drawing and as directed. 73 S&F in repair of new seat of same size made of 12 mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam 50 mm thickness with PVC lipping all around along with welding of of mettallic rail structure where required and shall be fixed to the rail with screws alongwith washers complete all as specified in drawing and as directed. 74 S&F in repair of Gas lifting hydraulic system of Chair computer complete all as specified in drawing and as directed. 75 M&L for removing the old unserviceable handle / armrest of Chair computer & S&F of new handle of same size made of black integral skin polyurethane with reinforced MS insert and shall be back fixed to the rail with screws alongwith washers as per sample approved as specified and as directed. 76 S & F in repairs of wheel base of Chair computer complete all as specified and as directed. 77 S&F in repairs of castor wheels of Chair computer complete all as specified and as directed. 78 REPAIR TO TABLE COMPUTER TP/FD/E6/MAP/03 79 M&L for removing old unserviceable top of Table computer and S&F of new top made of pre laminated particle board 18 mm exterior grade ISI marked with 4mm thick 2nd class teak wood edging all around complete as specified and shown on drawing and as directed. 80 M&L for removing old unserviceable shelf of Table computer and S&F of new shelf made of 18mm thick pre laminated particle board complete all as shown on drawing and as directed. 81 M&L for removing old unserviceable Keyboard Tray of Table computer and S&F of new Keyboard Tray made of 18mm thick pre laminated particle board on telescopic channels complete all as shown on drawing and as directed. 82 M&L for removing old unserviceable Drawer of Table computer and S&F of new Drawer made of 18mm th pre laminated particle board on telescopic channels complete all as shown on drawing and as directed. 83 M&L for removing old unserviceable/ broken Nylon Buffers of Table computer and S&F of new Nylon Buffers to be provided on each legs complete all as shown on drawing and as directed. 84 CHAIR CB STEEL WITH/ WITHOUT ARMS (FD-75M) :- 85 M & L Taking down carefully existing unserviceable seat frame and S & F new seat frame made out of 2nd class hard wood duly caned with white plastic cane 2mm wide for seat and 3mm wide for border as per Godrej pattern Cane, Type-I (HDPE) as per IS: 5378-1994 and applying twocoat of black French polish with glossy finish over wood filler on all exposed new wooden surfaces after preparation of new wooden surface completebefore canning complete all as shown on drawing and as directed. 86 All as per item No 17.01but back frame , complete. 87 Taking out old unserviceable/damaged hand rest from its position and S & F new hand rest made out of 20 mm thick teak wood plank in one piece on hand rest and applying two coat of black French polish with glossy finish over wood filler over a coat of primer on all exposed new wooden surfaces after preparation of new wooden surface before canning complete allas shown on drawing and as directed. 88 S & Fnew mild steel cleats of flat iron of size 25x3mm with drilling holes for fixing with MS screws to seat and back frame of each chair frame to support to seat/back wooden frame including applying two coats of synthetic enamel Olive Green/Grey colour paint over a coat of red oxide primer Complete all as specified and as directed. 89 M&L for denting / removing bends and removing the existing paintby applying chemical/aerosal spray and preparing the surfaceand applying a coat of synthetic enamel paint of olive green colour or any other colour/combination of colours complete as specified and directed.

INR 500 /-

INR 66000.0 /-

Refer document

FileName	File Description	File Size
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB