Tender For Furnishing And Electrical Work Union Bank Of India Branch Durg. => Limited; a FULLY GLAZED PARTITION 144.00 sqft Providing and fixing at site Fully Glazed partition to be fixed (as per the drawing) with 12.0mm toughened glass with approved itching pattern. All the exposed edges to be finished properly polished. The cost of partition shall include all labour, materials, etc complete. b PARTIALLY GLAZED PARTITION 407.25 sqft Providing and fixing at site Partly glazed wooden partition with 2” x 2” pine wood/ hard wood section to be fixed as a frame to the partition placed at 2 x 2 c/c, the frame is to be sandwich with 6.0mm commercial ply from both the sides and to be finished with approved shade of 1.0mm laminated finish, the middle portion of the partitions to have larger openings (as per the drawing) with 12.0mm glass with approved itching pattern. All the exposed edges to be finished with steam wood beadings properly polished to match the existing shade of laminates. The cost of partition shall include all labour, materials, etc complete. c SOLID / OPAQUE PARTITION 536.62 sqft Providing and fixing at site Opaque wooden partition with 2” x 2” pine wood/ hard wood section to be fixed as a frame to the partition placed at 2 x 2 c/c, the frame is to be sandwich with 6.0mm commercial ply from both the sides and to be finished with approved shade of 1.0mm laminated finish, (as per the drawing). All the exposed edges to be finished with steam wood beadings properly polished to match the existing shade of laminates. The cost of partition shall include all labour, materials, etc complete. d CEMENT BOARD PARTITION 166.78 sqft Providing and fixing at site partition upto ceiling height consisting of GI frame and required board, including providing and fixing of frame work made of special section power pressed/roll from GI sheet with zinc coating of 120 gms/sqm (both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia 50 mm length or suitable anchor fastener or metal screws with nulon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks. Galvanished MS fixing channel of 99 mm width (.9 mm thick having two flanges of 9.5 mm each with zinc coating of 120 gms/sqm (both side inclusive) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beards at corners (25mm X 25mm X 0.5mm), joint finisher and two coats of primer suitable for board as per manufactures specification and direction of architect all complete. 2 DOOR OF PARTITION a DOOR FOR GLAZED PARTITIONS 73.50 sqft Providing & fixing at site 35 mm thick flush doors shutters of approved make to be laminated on both faces with 1.0 mm thick laminate of approved colour & make with 35 x 5mm steam beach wood beading on edges of door. The door is to be fixed to main frame made with 4” heavy duty brass hinges The glass portion is 8 mm. thick float glass with itching. All edges of the door shall have steam beech wooden beading properly polished to match the existing laminated finish. Door closer, mortise locks, door stoppers, handles all accessories, labour etc. complete. b DOOR FOR OPAQUE PARTITIONS 115.50 sqft Providing & fixing at site 35 mm thick flush doors shutters of approved make to be laminated on both faces with 1.0 mm thick laminate of approved colour & make with 35 x 5mm steam beach wood beading on edges of door. The door is to be fixed to main frame made with 4” heavy duty brass hinges. All edges of the door shall have steam beech wooden beading properly polished to match the existing laminated finish. Door closer, mortise locks, door stoppers, handles all accessories, labour etc. complete. c GLASS DOOR 63.00 sqft Providing and fixing at site Main Entrance Full Glass 12.0mm Toughened Glass Door to be fixed and heavy duty Floor spring and pivot arrangement to be fixed in walls/ as per site with anchor fasteners and heavy duty mechanical screws. The door decorative type handles Brush finished SS handles 600mm long to be fixed in the glass shutter. 3 STORAGE 585.50 sqft Providing and fixing at site storage cabinet fully covered from all sides and 16 deep including necessary shelves as per the design and specifications with openable shutters made up of 19mm BWP ply, The rear portion is to be closed with 8.0mm ply, the top shall have 19 -25mm ply. Front of the cabinet is to be finished with 1.0mm thick laminate with approved pattern with different colour laminated finish of approved shade & colour with Proper Steam Beach molding, beadings, and different colour laminate as per pattern in shutters and in skirting strictly as per the design, pattern, including all necessary fittings, such as locks, handles. The inside portion is to be finished with .8mm thk inner laminate. The cost shall include all materials, labour, accessories etc complete. 4 FALSE CEILING a GYPSUM CEILING 792.12 sqft Providing and fixing gypsum false ceiling. in 12.5mm thick Gypboard (POP) plain false ceiling with GI suspended from RCC slab/ Beam as approved by Bank/ Architect including G.I. Parameter Channels of size 0.55 mm thick having one flange of 20mm and another flange of 30mm and web of 27mm along with parameter of ceiling, screw fixed, to the brick wall / partition with the help of nylon sleeves and screws at 600mm C/C. The suspended G.I. Intermediate channels of size 45 x 0.9 mm thick with two flanges of 15mm each from the soffit at 1200mm C/C with GI cleats and steel expansion fasteners. Ceiling sections of 0.55mm thick having web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to intermediate channel with help of connecting clips and in direction perpendicular to intermediate channel at 457 mm C/C. 12.5mm Tapered edge Gypboard channel at 457mm C/C in both the directions screwed fixed to the ceiling section with 25mm dry wall screws at 230mm C/C screw, fixing is done mechanically with drilling machine and suitable attachment. Finally the boards are to be jointed and finished with jointing compound, paper tape and two coats of top Coat, suitable for Gypboard (As recommended practice of India Gyp.) For light fittings in cut outs etc are to be made with a frame of parameter channels of size 20 x 27 x 30 x 0.5mm thick supported suitably. Angle beads, edge bends, control joints as required to be provided. The quoted rates to include all the above items, ceiling to be painted with minimum two coats of plastic emulsion paint including base preparation. etc. complete. b MINERAL FIBER BOARD CEILING 652.00 sqft Providing and fixing of false ceiling at all heights of 600mmx600mmx12mm armstrong mineral fiber ceiling tiles of type IBIZA RH -90 laid on armstrong prelude XL exposed grid systems with 9mm wide T Section flanges colour white. The frame work comprise of main runner spaced at 1200mm centers securely fixed to the structural soffit approved hangers at 1200mm maximum centers. Hangers (GI wire) to be fixed by approved roof plug and screws etc. The last hanger at the end of each main runner should not be greater than 450mm from the adjacent wall. flush fitting 1200mm along cross tees (with double stitching) to be interlocked between main runners at 600mm c/ c to form 1200x600mm modules. Cut cross tees longer than 600mm to be supported independently. 600mmx600mm modules to be formed by fittings 600mm long flush fitting cross tees centrally between the 1200mm cross tees. Perimeter trim to be armstrong wall angle secured to walls at 450mm maximum centers along cross tees (with double stitching) to be interlocked between main runners at 600mm c/ c to form 1200x600mm modules. Cut cross tees longer than 600mm to be supported independently. 600mmx600mm modules to be formed by fittings 600mm long flush fitting cross tees centrally between the 1200mm cross tees. Perimeter trim to be armstrong wall angle secured to walls at 450mm maximum centers. 5 PANELING a WOODEN PANELING 414.38 sqft Providing and fixing at site column paneling with 2 nd class steam beach wood 2 x 1.25 battens to be fixed over column/wall as per the requirement. Groove to be made over 6mm thick MDF board, which will be pasted over 9.0mm BWP Grade ply finished with Metallic colour laminated finished with given design. The cost shall include all materials, labour etc complete. b ACP PANELING 453.25 sqft Providing & fixing of paneling in Aluminium Composite Panel (ACP) with framing of Aluminium Tube sections of min 1.5 x 1 and 20 gauges 2-0 C/C both ways. Mirror screws to be used. Joints to be finished with Silicon based sealant. ACP thickness of 3 mm minimum. Aluminium foils thickness to be min 0.20 mm, 2-0 C/C both ways. ACP to be in 2 width panels or distributed equally. Alubond, Eurobond, Fujibond, Alcobond or equivalent ISO certified brands to be used. Shades to be as per banks approval. 6 FURNITURES a TABLES Providing & fixing of table with or without key board tray with table body of 18mm, 12mm & 6mm thk ply wood. Table top & shutters of 19mm thk block board & 1.0mm thk laminate. One drawer fixed on drawer slider, one shuttered shelf & a readymade metallic key board tray having the under sliding mouse tray must be fixed under the table top as & where required. Multipurpose locks & handles must be fixed in drawers & shutters. One PVC cable manager on the working top, a foot rest of 19mm thk block board & a CPU carrier must also be fixed on the footrest level. The table top & all other surfaces must be covered with laminates. The inside portion is to be finished with .8mm thk inner laminate. All the edges / corners must be protected with 6mm thk teak wood plain bead.4” high skirting of 12mm thk plywood must be fixed to all the exposed outer surfaces of the table & must be covered with laminate. The top edge of the skirting must be protected with 12mmX12mm quarter round of teak wood. All the teak wood must be finished with three coats of clear zink polish. i) BM’s 60 X 30 X 26(h) 1 each ii) Side Credenza 36 X 16 X 26 (h) 1 each iii) Officer’s/Workstation 50 X 26 X 26(h) 6 each iv) Side Credenza 30 X 16 X 26 (h) 4 each b CASH COUNTER Providing & fabrication of counters for Cash counter with counter body of 18mm, 12mm & 6mm plywood. Counter tops (the working top & the customer top) must be of 19mm thk block board & 1.0mm thk plywood. 2’3” wide working top must be at 2’6” ht from the floor. A readymade metallic keyboard tray along with under sliding mouse tray must be fixed under the working top. A drawer unit with 3 drawers must also be fixed under the working top. The drawer must be mounted on drawer slider. Multi latch locks, handles must be fixed in drawers. All inner surfaces must be finished with one coat of primer & three coats of synthetic enamel paint. All the corners/edges of plywood & block board must be protected with lipping of 6mm thk teak wood plain beads. 4” high skirting of 12mm thk plywood must be fixed to all the exposed outer surface of the counter & must be covered with laminate. The top edge of the skirting must be protected with 12mmX12mm quarter round bead of teak wood. One PVC cable manager on the working top; a foot rest of 19mm thk block board & a CPU carrier on the foot rest level must also be fixed. The inside portion is to be finished with .8mm thk inner laminate. All the teak wood must be finished with three coats of clear zink polish & the counter must be provided with cuts & slots to enable laying of electrical, telephone & data lines as per requirement. Cash Counter 50 X 26 X 26(h) 2 each 7 MISCLLANEOUS a NOTICE BOARD 1 each Providing & fixing at site notice board of size 3 x 2 to be made up of Steam Beach wood frame of size 2 x1 wooden section with 5.0mm plain glass The Notice board shall have 19.0mm soft board lining at back with approved shade of cloth, and lockable shutter strictly as per the design & drawing etc complete. b WRITING LEDGE 1 each Providing & fixing at site writing desk of size 900 x 450 x 1200 mm size made up of 12.0mm clear glass polished on exposed edges with lower shelf for keeping vouchers & above soft board for product catalogs to be hanged at the site with help of Stainless steel brackets, below writing desk making an wastage drop box with open able shutter, above shutter making an whole in front side of the writing desk, the cost shall include all materials, fixing at site etc complete. c CHEQUE / COMPLAINT DROP BOX 2 each Providing & fixing at site cheque drop box of size 1 x 13 to be made up of 1 st class Steam Beach frame of size 1 x1 wooden section in front 6.0mm plain glass The boxes shall have 12.0mm ply with approved shade of laminate, and lockable shutter strictly as per the design & drawing etc complete. d 12MM THICK GLASS TOP 106.00 sqft Providing & fixing bevelled edge Glass 8mm thick with provision of cable manager at table top of BMs Table and Workstations as required and as per the design complete. e VERTICAL BLINDS 137.50 sqft Providing & fixing at site VERTICAL BLINDS over windows with approved shade of fabric and strictly as per the design complete. f ALUMINIUM GRILL 93.50 sqft Providing & fixing at top of cash counter anodized aluminium framed grill (minimum anodic coating of Grade AC 15) of approved shape, pattern and design including cutting, bending, hoisting and erecting with fixing clips or hold fasteners or bolts and nuts as required etc as per the design & drawing etc complete. g INFORMATION PANEL BOARD 1 each Providing & fixing at site information panel as per UBI design enclosed, the cost shall include all materials, fixing at site etc complete.
