Tender For Sdp-Pamba-Providing Side View Cutter Near Police Mess Building. - Providing Side View Cutter 2 Engaging Mancoolie 3 Demolishing brick work manually / by mechanical means including stacking ofserviceable material and disposal of unserviceable material within 50 metres lead asper direction of Engineer-in-Charge.In cement mortar 4 Providing and laying in position specified grade of reinforced cement concrete,excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mmnominal size derived from natural sources) 5 Steel reinforcement for R.C.C work including straightening, cutting, bending, placingin position and binding all complete upto plinth levelThermo - Mechanically Treatedbars of grade Fe-500D or more 6 Reinforced cement concrete work in beams, suspended floors, roofs, having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,staircases and spiral stair cases up to floor five level excluding the cost of centering,shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (ZoneIII) derived from natural sources: 3 graded stone aggregate 20 mm nominal sizederived from natural sources). 7 Centering and shuttering including strutting, etc. and removal of form for:Lintels,beams, plinth beams, girders bressumers and cantilevers 8 Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cmor nearest available size confirming to IS 2185 Part I of 1979 for super structure up tofloor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etccomplete 9 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 10 Finishing with Deluxe Multi surface paint system for interiors and exteriors usingprimer as per manufacturers specifications:Two or more coats applied on walls @1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10sqm 11 Providing and fixing double scaffolding system (cup lock type) on the exterior side,upto seven story hight made with 40 mm dia. M.S. tube 1.5 m centre to centre,horizontal & vertical tubes joining with cup & lock system with M.S. tubes,M.S. tube challies, M.S. clamps and M.S. staricase system in the scaffolding forworking platform etc. and maintaining it in a serviceable condition for the requiredduration as approved and removing it there after. The scaffolding system shall bestiffened with bracings, runners, connection with the building etc wherever requiredfor inspection of work at required location with essential safety features for theworkmen etc. complete as per directions and approval of Engineer- in Charge. Theelevational area of the scaffolding shall be measured for payment purpose. Thepayment will be made once irrespective of duration of scaffolding. Note:- This itemto be used for maintenance work judicially, necessary deduction for scaffolding in theexisting item to be done 12 Steel work welded in built up sections/framed work, including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer usingstructural steel etc. as required.In gratings, frames, guard bar, ladder, railings,brackets, gates and similar works 13 Finishing with Epoxy paint (two or more coats) at all locations prepared and appliedas per manufacturers specifications including appropriate priming coat,preparation of surface, etc. complete.On steel work 14 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch ofcorrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coatedthickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade,5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18microns. Sheet should have protective guard film of 25 microns minimum to avoidscratches during transportation and should be supplied in single length upto 12 metreor as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/selftapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch inhorizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters andtrusses and including cutting to size and shape wherever required. 15 Random rubble masonry in Cement mortar 1:6 (1 cement: 6 coarse sand) with hardstone in foundation and basement up to plinth level using departmental rubble. 16 Providing and laying in position cement concrete of specified grade excluding thecost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarsesand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mmnominal size derived from natural sources) 17 Providing and laying matt finished vitrified tile of size 300x300x9.8mm having withwater absorption less than 0.5% and conforming to IS: 15622 of approved make in allcolours and shades in for outdoor floors such as footpath, court yard, multi modelslocation etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarsesand) in all shapes & patterns including grouting the joints with white cementmixed with matching pigments etc. complete as per direction of Engineer-in-Charge. 18 Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded andprepolished, machine cut for kitchen platforms, vanity counters, window sills, faciasand similar locations, of required size, approved shade, colour and texture laid over20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated withwhite cement, mixed with matching pigment, epoxy touch ups, including rubbing,curing, moulding and polishing to edges to give high gloss finish etc. complete at alllevels.Area of slab over 0.50 sqm 19 Providing edge moulding to 18 mm thick marble stone counters, vanities etc.,including machine polishing to edge to give high gloss finish etc. complete as perdesign approved by Engineer -in-Charge.Granite work 20 Extra for making chequers of approved pattern on cement concrete floors, steps,landing, pavements etc. 21 12 mm thick plain cement mortar bands in cement mortar 1:4 ( 1 cement : 4 fine sand):Flush Band
