Tender For Construction Of Wua Buildings Under Jurisdiction Of Executive Engineer Water Resources Division, Khajuwala - Sub Division Khajuwala (Pacakage-446A)
Tender Value
2.26 Crore
Estimated cost
Bid Submission
26 Aug 2025
0 days left
EMD
4.52 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
khajuwala → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Construction Of Wua Buildings Under Jurisdiction Of Executive Engineer Water Resources Division, Khajuwala - Sub Division Khajuwala (Pacakage-446A)
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils |
| 2 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth levelM10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 3 | Brick masonry with F.P.S. bricks of class designation 75 in foundation and plinth with bricksCement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. |
| 5 | Providing and laying damp-proof course with cement concrete grade M-15 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound complete as per specification50 mm thick |
| 6 | Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in :Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 7 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. |
| 8 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level forSuspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills,chhajjas, lintel,beam, plinth beam etc. |
| 9 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. M20 grade Nominal Mix / Design Mix |
| 10 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. (\"Original producers\" who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786) |
| 11 | Precast terrazo tiles of approved make, 20mm thick with marble chips of size upto 6mm laid in floors, and landing, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete on 20mm thick bed of cement sand mortar 1 : 4.Dark shade using ordinary cement. |
| 12 | Precast terrazzo tiles of approved make 20mm thick withmarblechipsofsizeupto6mminskirting& risers, treadsof stepsand dados12mm thickcement plaster1:3(1cement:3coarsesand)jointedwith neatcement slurry mixed with pigment to matchthe shadeofthetiles,includingrubbingandpolishing completewithtilesofDarkshadeusingordinary cement. |
| 13 | ProvidingandfixingM.S.sheet1mmthicksingle leafdoorshutterinangleironframe35x35x5mm suitabillydiagonallybracedwith25x3mmflatiron aboveandbelowlockrailofsize50x5mmbeading extraincludingallfittings,asperdirectionofEngg. inchargebutexcludingcostofchowkhats:including two coats of anit-corrosive red oxide primer paint |
| 14 | Provideandfixingexternalgradeboardsolidcore singleleafflushdoorshuttersISI2202-67marked usingphenolformaldehyderesiningluebothsides with approvedsteel fittingcompleteasperannexure \"A\"25mm thickcommercial veneer both side |
| 15 | Providing,hoistingandfixinguptofloorfivelevel precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand:4gradedstoneaggregate6mmnominalsize) reinforced with 1.6 mm dia Mild steel wire including centringandshuttering,rougheningcleaning,fixing and finishing in cement mortar 1 : 3 (1 cement : 3 fine sand ) etc complete as per approved design excluding plastering of jambs, sills and soffits40 mm thick |
| 16 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish12mm thick. |
| 17 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete.40mmthickwith20mmthicknominalsize aggregate. |
| 18 | Plaster on new surface on wall in cement sand mortar 1:3 including racking of joints etc. complete fine finish :20mm thick |
| 19 | Painting with synthetic enamel paint of approved brand and manufacture togive an even shade Two or more coats on new work |
| 20 | White washing with lime to give an even shade including all scaffolding:New work (three or more coat) |
| 21 | Colour washing of all shades to give an even shade including all scaffolding: |
| 22 | Painting top of roof with bitumen of approved quality at 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10sqm including cleanin the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete; With residual type petroleum bitumen of penetration 80/100 |
| 23 | Kota stone slab 20 mm to 25 mm thick (semi- polished) |
| 24 | Construction of Soakage well in all types of soil of approved drawing, top 90 Cm .Portion in 450mm thick masonry with CM 1:6, 80 mm thick stone slab covering, jointing of slab in CM 1:3 ,Ralthal, kharanja 40mm thick M-15 grade C.C flooring, earth work etc . complete including disposal of surplus earth within a lead of 50 mtr .Inner dia60 Cm & 10 to 12 Mtr deep. |
| 25 | P. & F Squatting Pan (Indian type) white glazed vitreous china 1st quality W.C. Pan (IS : 2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor (excluding the pair of foot rest.)Size 450mm |
| 26 | Vitreous china foot rests 250x130x30 mm |
| 27 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15mmC.P.Pillarcock(IS:8934Mark)&32mmC.P.brasswastecouplingofapprovedmake,P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall :Size 450 mm x 300 mm |
| 28 | P&FrigidPVCPipe(IS:4985mark)classII/(4 Kg./Cm2approvedquality/makeincludingjoining the pipe with solvent cement rubber ring and lubricant. 110 mm dia |
| 29 | P&FrigidPVCpipefittings(IS:4985mark)of approvedquality/makeincludingjoiningthepipe with solvent cement rubber ring and lubricant: 110mm dia |
| 30 | Coupler (Socket)110 mm |
| 31 | Plain Tee 110 mm |
| 32 | Bend 87.5 110mm |
| 33 | Vent Cowel 110 mm |
| 34 | P-Trap |
| 35 | P & F Gun-metal Non-return Valve or Check Valve (IS : 778 Make) of approved make, superior quality: 15mm nominal bore.Vertical |
| 36 | P & F Stop Cock (IS :8931 Mark), superior quality & of approved make:Brass 400 gm. 15mm nominal bore. |
| 37 | P & F Stop Cock (IS :8931 Mark), superior quality & of approved make:Brass1350gm. 25 mm nominal bore. |
| 38 | P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make:Brass 400 gm,15mm nominal bore. |
| 39 | P&FPVCStorageTankISIMarked(IS:12701) indicatingtheBISlicenseNo),ofapprovedmake with cover, 25mm dia 1M long G.I. over-flow pipe &25Cm.longwashoutpipewithplug&socket, includingmakingconnectionetc.,completeof approved design: 500 litres capacity |
| 40 | Providing and fixing Polyethylene - Aluminium - Polyethylene (PE-AL-PE) Composite Pressure Pipes as per 15450 : 2004 U.V. stablised with carbon black having thermal stabillity for hot and cold water supply, capable to withstand temperature upto 80ºC including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers connectors etc.with clamps at 1.00 metre spacing.This include the cost of cutting chases and including testing of joints complete as per direction of Engineer In chargeConcealed installation including cutting chases and making good the walls etc. complete.2025 (25mm OD) pipe |
| 41 | ProvidingandfixingPolyethylene-Aluminium- Polyethylene(PE-AL-PE)CompositePressurePipes as per 15450 : 2004 U.V. stablised with carbon black having thermal stabillity for hot and cold water supply,capabletowithstandtemperatureupto80ºC includingallspecialfittingsofcompositematerial (engineering plastic blend and brass inserts wherever required)e.g.elbows,tees,reducers,couplers connectors etc.with clamps at 1.00 metre spacing.This include the cost of cutting chases and including testing of joints complete as per direction of Engineer In chargeConcealedinstallationincludingcuttingchasesand making good the walls etc. complete.3240 (40mm OD) pipe |
| 42 | P & F Flush Cock / Flush Valve (IS : 9758 Mark)for WC of approved quality make Brass / Gun metal Half-turnwt.1Kg.ofapprovedquality/make, 25mmnominalbore. |
| 43 | Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m,10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr.Inside size 300 X 300 mm depth upto 0.5 M Cement cover with frame. |
| 44 | SITC of ContactorOEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Cordinatiom Chart andmade out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFFpush buttons,ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work. .For single phase Submersible / Monoblockpump0.5 HP to 1.5 HP (DOL starter) |
| 45 | 120 cm high fencing with angle iron posts 50x50x6mm placed at every 3 meters apart 30 cm . in ground embedded in cement concrete 1:3:6 (30x30x45cm) corner & every tenth post to be strutted with 50x50x6mm angle iron provided with four horizontal line and two diagonals of black barbed wire between two post fitted and fixed with G.I. staple including earth work in exacavation etc. complete.Add or deduct for 3 wires line over basic item |
| 46 | Providing and fixing steel gate,grating , and grillmade of angles ,tees , square bars , flats , or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red-oxideExtra if square , rectangular hollow tubelar section are used or grill made by flats only |
| 47 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it\"s ISI marked (IS:3419-1988) accessories, round tiles,1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose /Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter E - 04, E- 05 & E - 07 For additional technical parameters of product / work. |
| 48 | Short point (up to 3 mtr.) |
| 49 | Medium point (up to 6 mtr.) |
| 50 | S&F following sizesof ISI marked ( IS:14927 P - II ) virgin materialUPVC trunking along with accessories likecoupler,inner,outer,elbow,square box,tee,endcapetc.onsurface with screws, expansion fasteners as required. For additional technical parameters of product / work .25 mm x 12 mm |
| 51 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load andsite requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above ratingincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work.Double pole MCB(With B/C curve tripping Characteristics)6 A to 32 A rating |
| 52 | P & F ISI marked (IS :3854) 16 amp. flush type non modular switch CM/L no. printed and made out from industrialgradePolycarbonateorfireresistantABS materialincludingcuttingholeintileandmaking connectiontestingetc.asrequired.Allasperpre approvedbyEngineerin charge. For additional technical parameters of products/ work. |
| 53 | Providing&FixingofISImarked(IS:1258) batten/angle lamp holder with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screwsincludingmakingconnectiontestingetc.as required.AllasperpreapprovedbyEngineerin charge.For additional technical parameters of products/ work. |
| 54 | Providing& Fixingof3/6 pin 16 ampflush type non modular socket made out from Industrial grade PolycarbonateorfireresistantABSmaterial,brass terminalwithPorcelainbasedbackcover&captive screws including cutting hole in tile and making connectiontestingetc.asrequired.Allasperpre approved by Engineer in charge. For additional technical parameters of products/ work. |
| 55 | Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminiumhousing with in built driver, System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short &Open circuit protection ,THD < 10% , P. F.≥0.95, CRI>80 , life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K(As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work.570mm (+/-10%) batten with min. lumen output 1000 lm |
| 56 | Providing & Fixing ofof M.S. J- hook of standard design made out of 16 mm dia. M.S. round bar and fixed withcement concrete mortar with required support as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work. |
| 57 | Providing&Fixingof1200mmsweepBLDC technologypowersavingceilingfanwhichcan withstandonvotagefluctuations from140voltsto 240volts,powerfactornotlessthen0.9,service value (CMM/W) minimun 6.85 , air delivery minimun 220CMM,speedminimum330RPM(toleranceas per IS:374 2019 ) THD less then 10% and complete withdownrodof15mmdia.ERW(Electrical resistance welded ) of 1.6mm nominal thick medium duty steel pipe up to 80 cm, cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per preapprovedbyEngineerincharge. Foradditional technical parameters of products/ work.Without Remote. |
| 58 | Providing&FixingofofISOcertifiedcompany made Multiple socket with surge and spikes protectioncartridgenotlessthen5KVasperPWD specification for electrical Works with minimum four nos. universal 6 A sockets, one 6 A switch and 3 pin company fitted plug top and 3 core multistrand copper leadminimum1.5mtr. includingmakingconnection etc as required. All as per pre approved by Engineer incharge. Foradditionaltechnicalparametersof products/ work. |
| 59 | Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith IP- 20 rating ,includingall as per pre approved by Engineer in charge,making connections, testing etc. as required.For additional technical parameters of product / work.5 step fan regulator 2 Module 360 dgree rotating. |
| 60 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathedUn-armouredCopper cableconfirmingto IS:1554 P-I / IS :7098 P - I of 1.1 KV withelectrolytic gradeCopper made of copper rodsconfirming to IS 613-1964,ofpurity>99.7%,Inner/outersheath confirmingtoIS:5831inexistingRCC/Hume/ Stoneware/PVC pipe/openduct/cabletrench/ Cabletray(withcabletie)including testingetc.as required of following size. OEM must have it\"s own in house NABL accrediated Laboratory for testing procedureasperIS:10810Foradditionaltechnical parameters of product / work.1.5 Sq. mm.2 core . |
| 61 | Providing&FixingofIK08,IP66protectedLEDStreet Light Luminaireon existing bracket/pole. Fixture madeof powder coatedsinglepiecepressurediecastaluminum materialwithheatdissipationfinsonhousingwithUV stabilizedPC(UVstablizationreportsubmittedforUV cover ) /ToughenedGlasscover and secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy >=125 lm/ wtand potted driver& has a unique BIS R number withInput Voltage AC 120 to 270 V ACwithHighvoltageCutoff@>=300VACandAuto resettingSafety,PowerFactor>0.95driverEfficiency>85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C .driver current <750mA. The luminaire shall be BIS certified and Trade mark certified. Life Expectancy Equalormorethan50000burninghrswith Minimum70%lumenmaintened,CRI>70andCCT 5700K+355K.Surgeprotectionshallbemin≥4KV internal and min 10 KV external inside driver compartment. driver should be Phase to phase protection of 440 V for 4 Hrs. ManufacturesWordMark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80)Certificate/reportwithliablewarrantyof product/accessoriesfromOEMshallbesubmitted.Allas perpreapprovedbyEngineerincharge. Foradditional technical parameters of products/ work.LED Street Light fixture with Minimum lumen output 5600 lm . |
AI Tender Summary
Tender Timeline
Aug 07, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedAug 26, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 27, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender