Tender For Spl Repair Bldg No T-52 (Dining Hall) Of 8 Garh Rif Under Ge Dehradun; 1 Demolition brick or stone masonary built in cement mortar including all quoins arches pillars etc but excluding ashlars facing dressed stone work and precast concrete block, complete all as specified and as directed by Engr-in-Charge. 2 Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level). 3 M&L brick work with sub class B brick straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6 including all quoins, arches, pillars etc complete all as specified 4 Ditto as item No. 03 above, but except brick complete all as specified. 5 Excavating in trenches in any type of soil , n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out complete all as specified 6 M&L for Cement concrete in 1;4:8 type D-2 (40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified 7 M & L for RCC M-25 Design mix{ using 20 mm graded stone aggregate) in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc and mass concrete complete all as specified and directed by Engineer-in-Charge 8 M&L for RCC M-25 Design mix { using 20 mm graded stone aggregate) in columns, pillars, piers, posts and struts complete all as specified and directed by Engineer-in-Charge 9 M&L for RCC M-25 Design mix { using 20 mm graded stone aggregate) in beams,cantilevers,wall bends, bressummers, lintels over 1.5m span complete all as specified. 10 M&L for RCC M-25 Design mix { using 20 mm graded stone aggregate) in Chajjacomplete all as specified. 11 M&L for Mild steel TMTbars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified 12 Ditto as per item No 7 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders 13 Use and waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified 14 Use & waste of formwork to sides of pillers, posts, struts, piers, columns and stanchions etc for fair finished surfaces of concrete complete all as specified and directed. 15 Use and waste for Formwork to sides and soffits of floor or roof beams, wall bend beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.complete all as specified 16 Use & waste of formwork to slab, chajjas,etc for fair finished surfaces of concrete complete all as specified and directed. 17 M&L Formwork flat rough finished to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide. (Where RCC/PCC band in walls, spanning and openingcomplete all as specified. 18 M&L for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified 19 M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified 20 M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified 21 M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified 22 M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified 23 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified 24 Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting pointcomplete all as specified 25 M&L for applying interior/Exterior grade wall care putty 1 to 1.50 mm thick to make the surface smooth as specified and directed by Engr-in-Charge. Make: Berger/Asian/JK/Birla 26 M&L for applying two coat of exterior weather proof 100% anti fungal acrylic smooth emulsion with silicon additives that offer anti alge high performance exterior wall finish with 6 years of performance warranty by manufacturer applied by using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacture with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper, should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed. 27 M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified 28 Taking down wooden chowkhats or frames with shutters area n. exc 1.5 sqm each (without taking off shutter from the frame) complete. 29 Taking down wooden chowkhats or frames with shutters area exc. 1.5 Sqm but not exceeding 4 Sqm each complete. 30 Supply and fix in repair aluminum alloy powder coated door made out of hollow extruded aluminum section as mentioned below. Each door having 02 Nos Disc or D type handle, 02 Nos aluminum tower bolt 200 mm size, one brass mortice lock of six lever with key in duplicate regulated by double action hydraulic floor spring heavy duty (Make:- Sandhu/Ritz) shutter to be partly glaze with 5mm thick tined coloured glass in upper pannel and partly pannelled with 12mm thick both side laminated particle board in lower pannel fixed with glazing clip, rubber beading/gasket, anodised aluminum beading screw complete all as specified and directed at site. Chowkhat Frame:- 101.60x44.45x1.60mmShutter verticle style :- 85x44.45x1.56mm Shutter middle Rail :- 83.50x44.45x1.54mmShutter Top Rail and bottom Rail :- 114.30x44.45x1.55mm 31 S&F mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 including necessary welding, drilling hole complete. 32 Material and labour for aluminum alloy powder coated standard hollow section as mentioned below window frame (Bombay sliding) with two glazed shutter andone noswire gauged shutter sliding type, with aluminum sections as per Series-A(15mm) 3 track of Jindal section numbers for sliding windows,and glazed with tinted glass coloured glass 4mm thick, fixed with glazing clips, rubber beading / gasket anodised beading, screw and lock type handle of size 75mm, 2 Nos aluminum tower bolt 150mm long with stainless steel grill consisting of 12 mm square bar & 40 x 5 mm thick SS flat all around incl making good of existing surfaces with plaster and external (cement base paint)/ internal (OBD) finishes complete all as specified and directed. Shutter Top & bottom size : 37.50x15x1.60mmShutter inner lock size 37.50x15x1.60 mm Shutter side (Handle) size 37.50x15x1.36mmChowkhat bottom size : 50.30x26x1.20mmChowkhat top & sides size:50.30x26x1.00mm 33 S & F stainless steel handles 125 mm long one piece and fixed with screws/welded to frame ,complete 34 S&F 18 mm thick WPC board one side prelaminated and other side plain white colour as in cup board shutters and frames, kitchen cabinet frontshutter, partion, shelf, & drawer, fixed with screws, solvent cement / adhesive incl dismantling old existing boardcomplete all as specified and directed by the Engineer-in-Charge. 35 S&F 18 mm thick WPC board both side plain white colour as in cup board shutters and frames, kitchen cabinet frontshutter, partion, shelf, & drawer, fixed with screws, solvent cement / adhesive incl dismantling old existing boardcomplete all as specified and directed by the Engineer-in-Charge. 36 S&F magnetic catcher and striking plate including letting in and fixed complete. 37 S&F Continious (PIANO) hinges, mild steel, bright finish or electrogalvanised. 30 mm width of flaps (when open) complete allas specified as directed. 38 Demolition of reinforced cement concrete, of any description complete all as directed. 39 Use and waste Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) of fair finished surfaces complete all as specified and as directed. 40 M & L for RCC(1:2:4) (using 20 mm gradedstone aggregate) as in slabs supported on wall, beam and columns in floors ,roof slabs, shelves and cover slab Including demolition of existing old RCC complete all as specified and as directed. 41 S & F mild steel TMT bar 8mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed. 42 M&L 16-18 mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match withshade of granite complete all as specified 43 M&L grinding and polishing to edges and rounding of granite kota or marble slab and smooth finishing complete all as specified and as directed 44 Taking down/ dismantling asbestos (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified. 45 Dismantling of framed or unframed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed. 46 Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed 47 S&F for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.Fe 410-W(Gde E-250) quality-A complete all as specified and directed. (Note: Hollow steel sections will not be used against this item). 48 S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screwscomplete all as specified and as directed. 49 S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and profile should match with galvalume sheet complete all as specified and as directed. 50 M & L applying two coats of synthetic enamel paint onnew or previously untreated steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. 51 M&L for 25 mm thick cement concrete type B-0 1:2:4 (12.5 mm graded stone aggregate) as in floor finished complete all as specified and as directed. 52 M&L double charged vitrified ceramic coloured tiles 10 mm thick (square/rectangular) polished,area of each tiles not exceeding 0.36 sqm, in floor etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified 53 All as per item No 39.00 here in above but as in skirting and including 10 mm thick rendering in cement mortar 1:4, complete all as specified 54 M & L non Skid ceramic tiles7-8 mm thick(Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors e.t.cin floors etc set and jointed in neat cement slurry and pointed in coloured cement to match of coloured tiles over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified 55 M&L glazed ceramic colour tiles size 300 mm x 450 mm x 6-7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering in cement mortar 1:6 (but not backing) andrubbish off the premises complete all as specified 56 M&Lfor looking mirror size 600x450x5mm selected qualaity mounted on 6mm commercial plywood and fixed withbrass screw and cup washer incl aluminium frame complete all as specified 57 S&Fvitreous china padestal wash hand basin, white flat back, size 580x450mm excluding taps, waste pipe chain and plug and porcelain but including brackets all as specified 58 S&F CP central hole basin mixer fancy type 15mm dia all as specified and directed. 59 M&L for PCC 1:3:6 type C-1 using 20 mm graded stone agg as in plinth protection finished surfaces even and smooth without using extra cement complete all as specified and as directed. 60 M & L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in benching to drain, holdfast, padding to roof/chhajja, coping, bed block etc. and the like edge slightly rounded or chamfered including necessary use and waste of form work and demolition of existing old cement concrete (un-reinforced) not exc 15 cm thick inground floor and paving below or above ground level complete. 61 M&L Hardcore of broken bricks or boulder gauge exc 63 mm but n. exc 100mm, deposited , spread and levelled in layers n.exec 15 cm thick, watered and rolled/rammed to a tue surface complete all as specified. 62 M&L 75 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone agg as in sub base complete all as specified and as directed. 63 M & L for coloured prepolished rubber moulded chequred cement concrete tile 30 cm x 30 cm x 20 to 22 mm thick with spacers 3mmset, jointed and pointed in neat cement slurry as in floor with grey cement and pigment over and including 15 mm thick screed bed in cement mortar 1:6, incl demolition of existing tile complete.Make NTC/Tulip. 64 M & Lfor sand filling under floors or in foundations including spreading & levelling complete all as specified directed. 65 M & L for pre-painted coloured (Red/Yellow) machine pressed precast concrete interlocking paver blocks of any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 grade with grey cement and pigment complete all as specified and directed. 66 S&F in repair SS grade 204 drapery rod 20mm diaincluding decorative brackets, decorative finals at both ends & curtain rings 8 Nos (Minimum) complete. 67 Providing & fixing false ceiling ofDesigner tile Ivory painted (High Pressure Steam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or electra) in true horizental level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and croos T of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main T at 600 mm c/c toform a grid of 1200x600mm and secondary cross T of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mmand laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main T runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable wire of 4mm dia with galvanised butterfly level clips, spaced at 1200mm c/c along main T, bottom exposed width of 15mm of all T sections of 4mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, including taking down existing ceiling of any type all complete at all heights as per direction of Engineer-in-Charge. 68 S&F galvanised steelwater tubing medium grade (ISI marked) with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing. 69 S&F galvanised steel water tubing medium grade (ISI marked) with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing. 70 S&F 1000 ltrs capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20 mm brass float valve with pvc ball complete all as specified 71 M & L 75mm th PCC 1:3:6 type C-2 as in plinth protection, finished even and fair complete all as specified. 72 S & F 75 mm bore UPVC (SWR) pipe 4 kgf/cm2 single socketed in any length with rubber ring, fixed on wall including dismantling of old pipes complete all as specified. 73 S & F in repair 110 mm bore UPVC (SWR) pipe 4 kgf/cm2 single socketed in any length with rubber ring, fixed on wall including dismantling of old pipes complete all as specified. 74 S&F 75mmPVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed 75 M & L PCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in benching to drain, holdfast, padding to roof/chhajja, coping, bed block etc. and the like edge slightly rounded or chamfered including necessary use and waste of form work complete. 76 M&L for 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. 77 M&L for hardcore of gauge exc 63 mm but n.exc 100 mm deposited, spread and leveled in layers n.exc 15 cm thick, watered and rolled/rammed to a true surfaces in broken stone or boulder complete all as specified and as directed. 78 M&L moorum/ red bajary filling in flloors or pavings, laid in layers n. exc. 15 cm thick, spread, levelled, and rammed including watering complete. 79 Point wiring with PVC insulated and unsheathedelectric wire 1100 volts grade single core FRLS having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional areadrawn in and including concealed non metallic rigid PVC conduit not less than 25 mm diawith all fitting and fixing accessories and1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable FRLS as continuous earth conductor, connected to earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes 1.6mm thick, 60mm deep including 3mm thick plastic hylam laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers for mounting switches, sockets including taking down point wiringetc complete for the following type :- Note:- (i) The quoted rates shall be deemed to be inclusive for cutting chasesin wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of point wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using PVC rawl plugs. (ii) Point wiring & earth wire shall be connected to each & every sunken box. (iii) All screws, fasteners, bolts, nuts & washer shall be cadmium plated & the cost of which is deemed to be included in the quoted unit rates. 80 One light point controlled by one, one way 6 Amp switchs 81 One fan/exhaust fan point controlled by one, one way 6 Amp switchs 82 One 5 pin 5/6 Amps socket outlet point on theindependentboard with other switchs. 83 One 5 pin 5/6 Amps socket outlet point onsame board controlledby one, one way switchs. 84 Description all as per item No 79 here in before but point wiring with 4 sqmm multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 4sqmm PVC insulated multi strand copper conductor cable as continous earth wire. 85 S & Finreplacementswitch piano, flush type, single pole one way 6 Amp . 86 S & F inreplacement switch piano, flush type, single pole one way 16Amp . 87 S & F inreplacement socket outlet, multipurpose, 2 in 1 5 pin, 6 Amp. 88 S&F inreplacement socket outlet, multipurpose, 2 in 1 5 pin, 16 Amp with fuse and neon indicator . 89 S&F in replacement electronic stepped type fan regulator 100 watt 230 volts AC 50 Hz 90 S & Finreplacement ceiling rose, 63.5 mm dia, ISI marked, three terminal of polycarbonate/isolated body. 91 S & F sub main wiringwithPVC insulated unsheathed FRLSH cable 1100 Volt grade,with multi stranded copper conductor drawing in and including rigid PVC conduit in concealed / surface as required at site including one runPVC insulated unsheathedcable with multi stranded copper conductor colour code as a earth continuity and connected upto DBincluding taking down old unsv submain wiring of following sizes .Note:(i)Tworun of single core PVC cable with one run of earth conductor & condiut shall be measured as one unit. (ii) The quoted rates shall be deemed to be inclusive for fixing the conduits to surface withusing PVC rawl plugs etc.(iii) Phasecolour code must be follow i.ePhase( Red) and Neutral (Black) In colour and for three Phase RYB For phase and black for neutral. 92 2 x 6 Sqmm+ 1 x 6 sqmm 93 2 x 4Sqmm + 1 x 4 sqmm 94 2x 1.5 Sqmm + 1x1.5 Sqmm 95 S & F inreplacementMCB SP 240 volts B Curve 10 KA . including connection with suitable size copper lugs of following capacity 96 MCB SP 6 to32 Amp.240 volts 97 MCB SPN 40to 63 Amps 240 volts 98 S & F in replacementDistribution box MCB Protected socket with Plastic enclosure (Surface mounitng ) 20 AMP MCB Combo box DP including plug top complete all as specified and directed 99 S & F in replacementMCB DB, sheet metal enclosures double door.The DBs should be supplied with tin platted insulated copper bus bar rated for 100A. 240 volts with IK09 type with blanking plates where required and IP 43 degree protection of following size:- 100 8 way SPNDB. 101 S & Fin replacementBatten holder, PVC/polycarbonate type with back plate suitable for batten fittings . 102 Supply and fixing LED building securitylight fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. 103 S&F BLDC Ceiling Fan complete with electronic type regulator and remote accessories 230 V,1200 mm sweep. BEE 5 star rated PVC AC single Phase 230 V / 240V 50 Hz of , complete connecting up ceiling rose to connector block of fan including fabricating and fixing ofFan hooks from ceiling truss/angle iron, required length of down rods (Aas per site requirement) and necessarynuts and bolts complete all as specified and directed. 104 Supply and Fixingin replacementhigh prssure die cast alluminium LED Batten light fitting 20W ,125 lumens /watt,IP-20,colour temp not less than 6500,inbuilt electronic driver, PF not less than 0.90 , inbuilt surge protection minimum 2.5KV 105 Material and labour for Earthing complete with galvanized ironearth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test point & to main switch board andtesting on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc.GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI light grade earth lead protection pipe etc complete all as specified and directed.Note: (i) Earth lead wire and its protection pipe upto and including 7.5 mtrfrom the top of earth electrode are included under this item. (ii) Any joints in earth lead from earth electrode to test point shall not be allowed/permitted.
