|
| 1 | Trimming of grass and weeds from the shoulders/berms and disposing off the same to suitable locations as per technical specifications Clause 1914 |
| 2 | T-05 CHALLEWADA KODSELGUDAM KAMALAPUR REPANPALLI ROAD |
| 3 | Providing, laying, spreading and compacting stone aggregates of specific sizes to Water Bound Macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 405.(Item No. 4.8 (2) (A) |
| 4 | T-05 CHALLEWADA KODSELGUDAM KAMALAPUR REPANPALLI ROAD |
| 5 | Construction of 50 mm thick Modified Penetration Macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506.Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.275 kg / sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503 |
| 6 | T-05 CHALLEWADA KODSELGUDAM KAMALAPUR REPANPALLI ROAD |
| 7 | Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.275 kg / sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503(Above M.P.M.) |
| 8 | T-05 CHALLEWADA KODSELGUDAM KAMALAPUR REPANPALLI ROAD |
| 9 | Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2mm to 5.6mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat as per Technical Specification Clause 508. (excluding seal coat |
| 10 | T-05 CHALLEWADA KODSELGUDAM KAMALAPUR REPANPALLI ROAD |
| 11 | Providing and laying Seal Coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B, as per Technical Specification Clause 510 |
| 12 | T-05 CHALLEWADA KODSELGUDAM KAMALAPUR REPANPALLI ROAD |
| 13 | Construction of earthen shouldersas per Technical Specification Clause 407 |
| 14 | T-05 CHALLEWADA KODSELGUDAM KAMALAPUR REPANPALLI ROAD |
| 15 | Reinforced cement concrete M-15 grade Ordinary Kilometer Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. |
| 16 | T-05 CHALLEWADA KODSELGUDAM KAMALAPUR REPANPALLI ROAD |
| 17 | Reinforced cement concrete M-15 grade 200m Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. |
| 18 | T-05 CHALLEWADA KODSELGUDAM KAMALAPUR REPANPALLI ROAD |
| 19 | Reinforced cement concrete M15grade boundary piller/local stone of standard design as per IRC:25 fixing in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704 |
| 20 | T-05 CHALLEWADA KODSELGUDAM KAMALAPUR REPANPALLI ROAD |
| 21 | PMGSY Citizen\" s information Board- Providing and fixing of typical MMGSY Retro Reflective information board as peras per section1700 of MORD specifications and latest MMGSY Signage Manual / Circuler and drawing.Two ACP (Aluminum Composite Panel) sheets of 4 mm thick, of 900 mm x 750mm size fixed at top & bottomduly rivetted with MSangles of 35 x 35x 5 mm thick M.S angle shall be welded by two vertical M.S angle of 5 mm thick to 75 mm x 75 mm of 12 SWG square tubes / 75mm Dia Pipe posts duly embedded in cement concrete M-20 grade blocks of 600mm x 600mm x 75mm, below ground level. MMGSY logo, letters and numerals on the ACP should be made up of Retro Reflective sheeting of Class-A / Class-B grade as per the latest MORD section 1700 specifications (Refer Circuler no. NRRDA-P013(11)/3/2019-Dir (Tech) dated 02.12.2019). Printing MMGSY Logo/ Project description on Class A or Class B type retro reflective sheeting using modern technology printing platform. The printer shall be approved by the retro reflective sheeting manufacturer and printed sign shall conform to retro reflective values as laid down in IRC 67-2012. The inks used for printing shall be eco friendly with VOC emissions complying to UL 2801 standards and specifications for the different kinds of platforms. The printed sign shall be laminated by UV protected laminate and shall carry a warranty of 5 years & 7 years for Class A and Class B sheeting respectively for traffic colors. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paints as per drawing Clause 1701 and Annexure 1700.1 (10.16). The design, painting and lettering shall be done as per the MMGSY Signage Guidelines Fig.3 and Fig.4 and as directed by Engineer-In-charge. A warranty for 5 / 7 years for the Retro reflective sheeting for Class-A and Class-B respectively, from original manufacturer shall be submitted by contractor. |
| 22 | T-05 CHALLEWADA KODSELGUDAM KAMALAPUR REPANPALLI ROAD |
