Percentage Rate Contract For Minor / Petty Daily Repair Works In New Facility At Hvf Factory; 1 Excavating in trenches, soft/ disintegrated soil not exc 1.5 m wide and not exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc 10 sq m on plan and not exc 1.5 m in depth and getting out. CuM 1773.53 2 Excavating in trenches hard dense soil, not exc 1.5 m wide and exc 1.5 m in depth; for foundation, etc., or for shafts, wells, cesspits, manholes, pier holes, etc., not exc 10 sq m on plan and getting out. CuM 958.76 3 Returning / refilling of soft / loose Soil including spreading, levelling, watering and well ramming in layers not exceeding 25cm. CuM 159.97 4 Earth work in excavation in all kind of soil by mechanical means (Hydraulic excavator/JCB)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. CuM 262.83 5 Excavating in post holes in Hard dense soil (or similar holes) each not exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm. Each 438.61 6 Surface dressing in hard dense soil, not exceeding 15 cm deep and getting out as directed. SqM 38.53 7 Supply and laying of sand filling under foundation where directed. CuM 2270.45 8 Removing excavated soil any type material exc. 250 m but not exc. 500 m and depositing where directed. CuM 372.60 9 Removing Rock debris / excavated materials, exc. 250 m but not exc. 500 m and depositing where directed at a level not exc. 1.5 m above the starting point. CuM 501.86 10 Material & Labour for Moorum/red bajri filling in floors or pavings, laid in layers not exc. 15 cm thick, spread, levelled and rammed including watering. CuM 1426.12 11 Material & Labour for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall. RM 38.18 12 Material & Labour for Providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete. SqM 320.39 13 Material & Labour for Anti-termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc., in apron. RM 102.58 14 Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors. SqM 242.65 15 Material and Labour for Cement concrete, Type D-2, 1:4:8 (40 mm graded aggregate) in foundations, filling and mass concrete. CuM 6305.57 16 Material and Labour for providing cement concrete (1:2:4) type B-1, using 20mm graded aggregate in roof kerbs, mud stops, rounded or chamfered on edges etc., for complete as directed. CuM 9624.70 17 Material & Labour for cement concrete, Type B-0 (1:2:4) using 12.5 mm graded aggregate, in Sunshade sloping, Roof sloping etc., Complete all as specified and directed. CuM 10648.31 18 Material and labour for cement concrete blocks using type B-1 concrete and setting the blocks in CM 1:6. CuM 10440.9 19 Providing precast cement concrete, Type B-1 (1:2:4) using 20mm graded aggregate, in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and set jointed in CM 1: 6. Complete all as specified directed. CuM 12692.30 20 Material and labour for 40 mm thick Cement concrete type B-1, 1:2:4 (12.50mm graded aggregate). SqM 393.07 21 Providing and laying Dry Lean Concrete(DLC) 125mm thick of aggregate gradiation as per table 1 of SP 49:2014 having 7 day average compressive strength not less than 7MPa.Minimum cement content not less than 140 Kg/CUM DLC mixed in Batching plant,transported to site and laid by electronic sensor paver including spreading and compacting using high amplitude tamping bars of paver(initial compaction) further by double drum smooth wheeled vibratory rollers with 80- 100KN static weight to achieve minimum dry density, necessary finishing etc complete all as specified and tolerances to be as per Table 900-1 of MoRTh specifications for Road and Bridge work 2013. PER 10 SqM 6553.09 22 Providing and laying Dry Lean Concrete(DLC) 150mm thick of aggregate gradiation as per table 1 of SP 49:2014 having 7 day average compressive strength not less than 7MPa.Minimum cement content not less than 140 Kg/CUM DLC mixed in Batching plant,transported to site and laid by electronic sensor paver including spreading and compacting using high amplitude tamping bars of paver(initial compaction) further by double drum smooth wheeled vibratory rollers with 80- 100KN static weight to achieve minimum dry density, necessary finishing etc complete all as specified and tolerances to be as per Table 900-1 of MoRTh specifications for Road and Bridge work 2013. PER 10 SqM 8254.00 23 Material and labour for Pavement Quality Concrete(PQC) of minimum 28 days field flexural strength of 45Kg/Sqcm or 4.5Mpa, aggregate gradation as per Table 3 of IRC 15-2017, coarse aggregate of clean, hard strong, dense, non porous and durable pieces of crushed stone or gravel, fine aggregates of clean natural sand or crushed stone sand or combination of both using minimum 360Kg/cum of cement with non-circular, virgin synthetic fibre of 12-18mm length, specific gravity 1.34 to 1.39, UV stable, alkali resistant, with equivalent dia 15-40 micron, minimum melting temperature as 240°C and minimum tensile strength of 300Mpa and at the rate as specified by the manufacturer laid, spread and compacted with slip-form paver of minimum 7.50m width, including curing and tining by texturing cum curing machine complete all as specified and directed.Required surface texturing to be done as specified in clause 10.1.14 and Table 9 of IRC:15-2017. CuM 9749.72 24 Material and Labour for Cutting channels, grooves or rebates not exc 15cm girth, and trimming surface including cutting of reinforcement. RM 363.86 25 Material and Labour for Cutting channels, grooves or rebates not exc 15cm girth, and trimming surface un-reinforcement. RM 133.29 26 Supply only of latex based liquid water proofing compound for incorporating in the concrete / mortar Dr. Fixit, Fosroc, Master Builder Solution make (or) suitably equivalent make as approved by EIC. Litre 300.73 27 Material and Labour for Brick work with sub class ‘B’ bricks straight or curved in plan with (1:4) cement mortar , Complete all as specified and directed. CuM 6176.08 28 Material and Labour for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6. Old Size Bricks. CuM 6731.89 29 Material and Labour for Brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4. SqM 716.20 30 Material and Labour for Fair cutting of channels, grooves or rebates, not exc 10 cm width or girth on exposed surfaces of brickwork such as in splays, chamfers, etc. including rubbed finish and waste and trimming surface in brick works (Straight or raking cutting). RM 98.31 31 Material and Labour for Formwork to sides of concrete foundations for flat surfaces , footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter. (Fair finished surfaces). SqM 456.68 32 Material and Labour for Wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown grade bitumen of any penetration applied hot @ 1.7 kg per sq. m, blinded with grit or pea size gravel @ 0.006 cu.m per sq.m, and lightly tampered (area of flashings, etc., shall be added to the roof area), complete all as specified and directed. SqM 160.05 33 Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces. SqM 115.13 34 Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner. SqM 1158.74 35 Supply and laying of APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified. SqM 464.20 36 Supply and laying of Hydraulically pressed burnt clay tile plain of size 200x200x19/20mm machine made laid over & including cement mortar screed 15mm thick in CM 1:6 mixed with water proofing compound and jointed pointed in CM 1:3 mixed with 5% crude oil by weight of cement. SqM 1023.58 37 Laying only of chequer plates 6 mm thick ( Plain or Chequered ) channels, square cut or notched ( Ordinary and counter sunk) formings holes, with welded attachment after the repair of the side nosing angles. kg 13.44 38 Supply and fixing of 600 mm dia Concertina coil fixed to the fencing post,compound walls etc. including fixed in repairs. RM 896.00 39 Supply and fixing of plain Galvnised M S Sheet of thick 0.31 mm / 30 guage fixing to Doors cut to size including necessary screws, nails complete all as specified and directed. SqM 84.00 40 Material and labour for machine cut cudappah stone slab 20-25mm thick, over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing. Complete all as specified and directed. SqM 976.47 41 Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. SqM 40.71 42 Supply and fixing of Aluminium dividing strips, 1.5mm thick, inserted in position, conform to design 38 mm width strip. RM 107.18 43 Supply & Laying of coloured Glazed ceramic tiles in vertical surface 350 x 250 x 7 mm/ 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match. SqM 1539.16 44 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. SqM 102.93 45 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. CuM 9792.14 46 Providing and laying 60mm thick factory made chamfered edge cement concrete paverblock of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete. SqM 1004.76 47 Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete SqM 1087.33 48 Supply & Laying of non skid Ceramic tiles, coloured, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. of set and jointed in neat cement slurry and pointed in white or coloured cement to match. complete as directed. SqM 1322.27 49 Supply & Laying for Non - skid Ceramic Coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match. SqM 1512.48 50 Supply & Laying Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match. SqM 1690.27 51 Supply & Laying Vitrified Ceramic tiles Dark shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match. SqM 1704.53 52 Laying only of Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade set, jointed with grey pigment cement and pigments, complete as directed. SqM 264.27 53 Supply and Fixing of Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade set, jointed with grey pigment cement and pigments, complete as directed. SqM 890.56 54 Laying only of Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade set, jointed with grey pigment cement and pigments, complete as directed. SqM 332.81 55 Supply and Fixing of Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade set, jointed with grey pigment cement and pigments, complete as directed. SqM 1098.25 56 Laying only of Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 100 mm thickness, M-50 Grade set, jointed with grey pigment cement and pigments, complete as directed. SqM 382.95 57 Supply and Fixing of Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 100 mm thickness, M-50 Grade set, jointed with grey pigment cement and pigments, complete as directed. SqM 1287.66 58 Supply and Fixing of Chequered cement concrete tiles with grey pigment cement and pigments 20cm x 20cm x 25mm thick, set, jointed with grey cement and pigments and pointed in neat cement slurry in floors, complete as directed. SqM 1265.35 59 Taking down plastering from walls built in cement mortar of any grade. SqM 33.18 60 Material and labour for Dubbing out average 10mm thick in C.M 1:4 on irregular face of walls (when specifically ordered in writing). SqM 195.66 61 Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:4) in patches in repairs not exc 3.0 sqm each as directed. Complete all as specified and directed. SqM 332.84 62 Rendering 12mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:3) in patches in repairs not exc 3.0 sqm each as directed. Complete all as specified and directed. SqM 327.31 63 Material & Labour for Screed Bed or bedding layer of mortar 20 mm thick for laying floor tiles in CM 1:4 for laying floor finishes. Complete all as specified directed. SqM 320.11 64 Material and labour for Dubbing out average 15mm thick in C.M 1:4 on irregular face of walls (when specifically ordered in writing). SqM 266.11 65 Complete removal of existing treatment on Walls. SqM 10.81 66 Demolition of brick work/ stone masonry built in cement mortar for the portions order to be dismantled. Complete all as specified directed. CuM 885.50 67 Demolition of damaged cement concrete (Unreinforced) of any description and in any position not otherwise specifically provided. CuM 1876.00 68 Dismantling of structural steel work including doors, gates, Angles, plates, Windows, purlins, weld mesh etc but excluding framed truss etc. from the position including cutting, welding, drilling wherever required and without any damage for re-fixing in the same place. Per Quintal 717.14 69 Removing building materials etc. (other than spoil payable under items 03028 to 03031 in Section- —Earthwork) to a distance of 100m or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination. Per Load 124.20 70 Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings SqM 32.43 71 Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings SqM 40.25 72 Fair cutting exc 10cm width or girth on straight or raking exposed surfaces of brickwork as to fire place apertures, splayed angles, weathering, cornices, groins, etc. including rubbed finish and waste SqM 611.6 73 Fair cutting exc 10cm width or girth on circular exposed surfaces of brickwork as to fire place apertures, splayed angles, weathering, cornices, groins, etc. including rubbed finish and waste SqM 1150.21 74 Providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete gloss finish etc. complete (Marble stone any description) RM 253.40 75 Providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete gloss finish etc. complete (Granitestone any description ) RM 432.69 76 M&L Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite(20mm thick) SqM 5961.26 77 M&L Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite(25mm thick) SqM 6136.64 78 M&L Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite(Except stone) SqM 3151.18 79 M & L Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.(20mm thick) SqM 5271.14 80 M & L Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.(25mm thick) SqM 5200.00 81 M&L Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.(Except stone). SqM 3162.65 82 M & L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete SqM 1181.51 83 M & L for Machine cut kota stone slab flooring 40-50mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete SqM 1514.09 84 M & L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete SqM 1223.95 85 M & L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete SqM 2757.41 86 M & L for 20mm thick Granite (of any type) tiles machine cut, in skirting/dado laid over cement screed and jointed with grey cementslurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete SqM 2809.16 87 M & L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations RM 55.78 88 M & L for Mirror polishing on marble/ granite/Kota stone/ stone work where ever required to give high gloss finish complete SqM 224.15 89 Supply & laying Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match SqM 1697.75 91 Supply & laying Virified Ceramic tiles dark shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match SqM 1850.12 91 Supply & laying Virified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match SqM 1841.38 92 Supply & laying Virified Ceramic tiles dark shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match SqM 2255.96 93 Supply & fixing of Steel door including projecting type hinges, steel handle, complete,with glazing bars, dovetailed or welded SqM 2735.15 .... more in document
