|
| 1 | Earth Work excavation in all classes of soils such as hard stiff clay, stiff black cotton, hard red earth, shales, murram, ordinary earth, earth mix with 50% fair sized boulders etc., with initial lead and lifts including laying, spreading, levelling, sectioning breaking clods etc., including all incidental charges etc. complete as per standard specification.(ForFoundations SS 20B ) |
| 2 | Providing Plain Cement concrete of mix 1:4:8 (One cement four sand eight aggregates) using 40mm ISS gauge sizehard broken including cost conveyance of all materisl to site including labour charges, transporting and placing in postion including labour for mixing compacting, finishing and curring etc. including cost and conveyance of all materials and labour charges etc., complete as per standard specification |
| 3 | Supplying & Erecting RCC centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists(Country wood) of size 10 x 6.5cm spaced @ about 90cm c/c and supported by casurina props of 10 - 13cm dia. spaced @ 75cm c/c etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.for the following items (For all R.C.C Works )including cost and conveyance of all materials and labour charges etc., complete as per standard specificationColumn footing |
| 4 | Column |
| 5 | Slab & Beam |
| 6 | Supplyingand Fabrication and placing in position of TMT bars for all RCC works with cost of binding wire and cost of cutting, bending ,tying in position including cost and conveyance of all materials and labour charges etc., complete as per standard specification. |
| 7 | Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone Sand (M- Sand), but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - |
| 8 | Providing granolithic floor finish of 25mm thickness with plain cement concrete 1:2:4 (One Cement, Two crushed sand (M-Sand) and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panellingwherever necessary and as directed by the departmental officers) |
| 9 | R.R. Masonry in Cm 1:5 mix using rough stone Bond stone including cost & conveyance and all labour charges etc., complete |
| 10 | Brick work in Cement Mortar in 1:5 ( One cement and Five Sand ) using best quality ofStockbricks2nd class of size 9x 41/2x 3including all cost of materials and labour charges includingCuring charges etc., complete as per Standard Specification. |
| 11 | Supplying and fixing MS L Angle directed by the departmental officers inclusive of cost of MS grill and labour charges including one coat of red oxide and fixing in position etc. complete (as per schedule of rates) as per standard specification |
| 12 | Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside.Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug. |
| 13 | Supplying and fixing in Position of Indian Oriya pan type water closet with “P’’ or “S’’ trap to set inbrick jelly concrete 1:4:8 Mix concrete 10 cm thick using 20mm brick jelly and top finished with c.m. 1:3 mix 20mm thick without any leakage etc. complete. |
| 14 | Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick laid in-situ and pointed with same coloured cement |
| 15 | Plastering with cement mortar 1:4 (One Part of Cement and Four part of Plastering Sand (P- Sand)) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications (S.I.309) |
| 16 | Plastering c.m 1:5(one cement and five sand) mix to a thick of 12mm using clean screened sand and including the cost of curing for 15 days from the completion of work and surface should free from undulations and including the cost of preparing the surface for plastering and protecting from other damages till setting of mortar etc complete complying as per MORTH Specifications. TNDSS No.56 & 57 |
| 17 | Supplying and laying in flooringwith fully polished Sinthetic Grey colour Granite stone of 20mm thick (average) of 4\" X 2\" in size laid over base layer of cementmortar 1:3 (one cement and three Plastering sand) - 20 mm thick and applying cement slurry &pointed with white cement and colour pigments to the colour of stones and polished neatly as directed by the deparmental officers |
| 18 | Painting the new walls two coats over one coat ofpriming with best Emulsion paint ofapproved colour andquality includingpreparation ofsurfaceandfinishing neatly etc., complete complying with standard specification and as directed by the department officers etc., complete complying with standard specifications. |
| 19 | Painting two coats with best-approved quality Colour Enamel paint for New Iron Works including cost and conveyance of enamel paint etc., Complete. |
| 20 | Supplying and Fixing of Aluminium Dye Cast Letters ofapproved size and colour. The colour treatment processis achieved with MRF colour coat and then the processedcoloured layer is set into the kiln for the heat treatmentprocess for the following sizes |
| 21 | Wiring with 2 x 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigidpipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of suitable colourfor open PVC light point / fan point (for electronic regulator) (5 points per coil)(For Electronicregulator) [SD NO.18] |
| 22 | Supply and fixing of WT bulk head fitting with guard (Philips / Bajaj / Crompton / K. Lite) suitable for11W CFL lamp with CFL. (SD 83) |
| 23 | Supply of 5000 Lit. capacity Plastic tank |
