|
| 1 | Comprehensive maintenance of DG sets , periodical servicing including first hand repairs, consisting of normal repairs such as tightening of nut bolts, greasing, checking/replacing of battery terminals, leveling of distilled water, cleaning of main ,battery charging alternator where ever exists with vacuum cleaner including replacements of defective/ worn out spares such as diesel filters, oil filters, rubber hose pipe ,V-belt, fuel pipe and change of oils etc. and cleaning of Radiator etc 200 KVA, Make;- Greaves cotton Ltd / Jyoti Ltd, SM No. 616/6010/DG/03 at Sarang building.( Dighi)Note:-(i) The maintenance cost of DG Set for month shall deemed to comprises of cost of labour employed for the purpose, T&P used and other petty items such as cotton waste, Kerosene oil, Grease, nuts, bolts, and labour cost for fixing spares. (ii)All spares and oil replaced will be measured and paid under relevant items of schedule ‘A’.(iii)Fixing charges for the spares and oil etc. are deemed to be included in quoted rate for comprehensive maintenance of DG Set if the spares are not included in Sch \"A\" then department will provide the same Free for fixing. (iv) Rectifying the defects in DG set any parts by tightening loose connections and rectifying defects, testing complete all as directed. (v) contractor shall detail his rap (machanic) to attend any type of fault /defects on complaint from engr-in -charge or his rep, and and will be attended within 12 hrs and fault should be repair within 48hrs. (iv) In case contractor fails to rectify defect within 48 hrs recovery @ Rs 500 per day will be carried out. |
| 2 | Ditto all as per item no. 1 but 125 KVA Engine Make - KOEL SM No. 616/6014/DG/09 at MCAE building.( Dighi) |
| 3 | Ditto all as per item no. 1 but 125 KVA Engine Make - Stamfordat CE building.(Dighi) |
| 4 | Ditto all as per item no. 1 but 100 KVA Engine Make Greaves SM No. 616/6011/DG/05 at Sarika building. (dighi) |
| 5 | Taking down defective self starter 12/24Volt of DG set of cap from 100 KVA to 200 KVA DG set installed at various installations and servicing/overhauling including replacing of worn out parts like solenoid, bearing, carbon brush, rewinding the starter motor winding, etc. and refitting the same after making serviceable for smooth functioning in all respect all as directed by Eng-in-Charge.Note:-Spares required and rewinding will be measured and paid separately under relevant item of this Schedule here after. |
| 6 | M&L for Rewinding the burnt field coil all as directed. |
| 7 | Rewinding the burnt armature coil with commutatorall as directed.. |
| 8 | Supply of bush/ bearing all as directed. |
| 9 | Supplythe worn out carbon brush with brush holder all as directed. |
| 10 | Supply of clutch all as directed. |
| 11 | Supply of solenoid switch all as directed. |
| 12 | Supply of Bentex drive all as directed. |
| 13 | M/L for cleaning the fuel tank both internally and externally by removing all the dust / sediments etc including writing of tank capacity, Date of cleaning,tank to be cleaned for following capacities of DG Sets all as directed. .(a) 200 KVA DG set |
| 14 | (b) 125 KVA DG set |
| 15 | (c) 100 KVA DG set |
| 16 | Supply & Fix in replacement of automatic voltage regulator 100 to 200 KVA DG set all as directed.. |
| 17 | Scrapping/cleaning the existing paint completely and painting with two coats of anti corrosion synthetic enamel paint with spray painting (Colour as per E-in-C code to be followed), DG Set, fuel tank writing SM No. and MES No. with given size of letters/Figures all as directed by Engr-in-Charge for DG Sets of cap as follows.(a) 200 KVA DG set |
| 18 | (b) 125 KVA DG set |
| 19 | (c)100 KVA DG set |
| 20 | Taking down the existing perished/damaged asbestos rope and supply and replace with new asbestos rope 10 mm thick on the exhaust pipe including covering with aluminium foil all as specified as directed by Engr-in-charge. |
| 21 | Supply diesel filter with \"O\" ring suitable for following capacity of DG sets as per sample:-(a) 200 KVA DG set |
| 22 | (b) 125 KVA DG set |
| 23 | (c) 100 KVA DG set |
| 24 | Supply Oil filter element with \"O’ring suitable following capacities of DG sets as per sample:-(a) 200 KVA DG set |
| 25 | (b) 125 KVA DG set |
| 26 | (c) 100 KVA DG set |
| 27 | SupplyAir filter element suitable for following capacities of DG sets as per sample:-(a) 200 KVA DG set |
| 28 | (b) 125 KVA DG set |
| 29 | (c) 100 KVA DG set |
| 30 | Supply set of belts suitable for following capacities of DG sets.(a) 200 KVA DG set |
| 31 | (b) 125 KVA DG set |
| 32 | (c) 100 KVA DG set |
| 33 | Supplyset of Rubber hose set for water and air circuit complete suitable for DG Sets of following capacities(a) 200 KVA DG set |
| 34 | (b) 125 KVA DG set |
| 35 | (c) 100 KVA DG set |
| 36 | Supplybattery leads set, PVC insulated multi-stranded, copper conductor 70 sqmm multi-stranded of 1.25 m long each duly fixed with brass clamps, copper lugs suitable for 100 to 200 KVA DG sets |
| 37 | M&L for replacement of brass battery terminal suitable for lead acid battery 12 v any AH |
| 38 | Supplyin sump / topping up engine oil, multi grade 20W/40 in engine or replacement of engine oil for DG SETS in R&DE (E) Dighi Make: Indian oil / Hindustan petroleum / Castrol. |
| 39 | Supplyelectrolyte of suitable Sp gravity for lead acid batteries in sealed containers |
| 40 | Supply of Coolant for DG sets of capacity 100 KVA to 200 KVA. |
| 41 | Supply petroleum jelly in 1 Kg plastic sealed container |
| 42 | Supply only distilled water for battery in 5 kg plastic sealed container. |
| 43 | Supply fuel pipe steel braided, steel stranded with benzo bolts and washers etc complete of length 30 cm long. |
| 44 | Supplyfuel pipe steel braded, steel stranded with benzo bolts and washers etc complete of length 45 cm long. |
| 45 | Supplyfuel pipe steel braded, steel stranded with banjo bolts and washers etc complete of length 60 cm long. |
| 46 | Supplyfuel level indicator transparent PVC pipe of suitable dia for fuel level in tank. |
| 47 | M &L for Removing the fuel injection pump (FIP) from DG set cap 100 to 200 KVA and carry out servicing and calibration from authorised maker\"s work shop including replacement of injectors, nozzles, etc. and refitting the same for smooth and efficient functioning all as directed by Engr-in-Charge. Note :-Repairs will be carried out from authorised workshop of MICO or manufacturer of DG set. |
| 48 | M&L for Repair to Radiator assy by disconnecting the radiator from engine frame and servicing/cleaning with acid and brazing where required to stop leaking tubes/joints etc. cleaning fins and re-fixing the same for DG set 100 KVA to200 KVA all as directed by Engineer-in-Charge. |
| 49 | M&L for Repairs of Turbo charger including replacement of worn out parts such as shaft, seal, bush bearing etc. |
| 50 | Taking down the defective water pump from DG set of any type and capacity and replace with new one for DG set of cap 100 KVA to 200 KVA all as directed by Engr-in-charge. |
| 51 | Material and labour for carry out initial charging with filling Sulphuric acid and distilled water upto level required to Battery 12 Volts, 180 AH of any make incl transportation to work shop and back all as directed by Eng-in-Charge |
| 52 | Taking down the defective flexible coupling at exhaust manifold end fix new flexible coupling stainless steel as per sample. |
| 53 | M&L for replacement of exhaust manifold with gasket, and all other connected parts upto 200 kVA DG set engine all as specified and directed |
| 54 | Supply and fixing in replacement digital ammeter 0 to 300 Amps |
| 55 | Supply and fixing in replacement digital voltmeter0 to 500 amps |
| 56 | S & F in replacement self starter suitable for 200 kVA DG set |
| 57 | S & F in replacement self starter suitable for 125 kVA DG set |
| 58 | Labour only for comprehensive maintenance (consisting of normal repairs)/ preventive maint and attending day to day breakdown of electrically operated travelling (EOT) cranes of following capacity comprising of hoist motor, long travel motor, gear box control panel and connected accessories, including replacement of the unserviceable spare parts with new at site complete all as specified and directed by Engineer-in-charge installed at following locations(a) EOT Crane 03 Ton capacity installed at ETH & ETF Bldg, Make : Cranex Ltd |
| 59 | (b) EOT Crane 5 Ton capacity installed at Machine shop building Make: INDO ENGR, MES No : 616/7013/CN/90 |
| 60 | (c) EOT Crane 08 Ton capacity installed at FPW, Make : Cranex Ltd |
| 61 | (d) EOT Crane 10 Ton capacity installed at storage Sakav Bldg, Make - Toyjm. |
| 62 | (e) EOT Crane 10 Ton capacity installed at PJ - 10 (Saranga) bldg MES No : 616/7015/CN/03 |
| 63 | (f ) EOT Crane 20 Ton capacity installed at Surya bldg Make : M/S RANKMES No : 616/7017/CN/06 |
| 64 | M&L for checking of Load Carrying Capacity and serviceability of each crane and hoistin the presence of Engr-in-charge,and test certificate to be produced in duplicate. The capacities of crane / hoist are as under:-(i) EOTCranes2 to 5 Ton Capacity(a) EOT Crane 5 Ton capacity installed at Machine shop building Make: INDO ENGR, MES No : 616/7013/CN/91 |
| 65 | (ii) EOTCrane 10 Ton Capacity(a) EOT Crane 10 Ton capacity installed at PJ - 10 (Saranga) bldg MES No : 616/7015/CN/03 |
| 66 | (iv) EOT Crane 10 Ton capacity installed at storage Sakav Bldg, Make - Toyjm. |
| 67 | (v) Eot Crane 20 Ton Capacity(a) EOT Crane 20 Ton capacity installed at Surya bldg Make : M/S RANK MES No : 616/7017/CN/06 Note:- for item No. (i) to (v)( i) Load required for testing to be arrange by contractor (ii) Load testing is inclusive of shifting, transporting the load place to place unloading will be arranged by contractor. It also includes required ropes, man power etc. for handling the load. |
| 68 | M & L for repairs to gear box including replacement of worn out driving/ driven gears, bearings, gear keys, gasket oil seals of capacity 2 ton to 5 ton all as specified and directed by engr-in-charge |
| 69 | M & L for repairs to gear box including replacement of worn out driving/ driven gears, bearings, gear keys, gasket oil seals of capacity 10 to 20 ton all as specified and directed by engr-in-charge |
| 70 | SupplyHRC fuse contacts complete with base from 5 to 16 amps capacity incl replacement of old fuses. Make : EE/L&T. |
| 71 | Supply and fix HRC fuse contacts complete with base from 20 A to 40 amps capacity incl replacement of old fuses. Make : EE/L&T. |
| 72 | Supply & fixpendant push button all as specified as directed. |
| 73 | S & F in replacement Current Collector all as specified as directed. |
| 74 | S & F in replacement AC Electromagnetic Brakes all as specified as directed. |
| 75 | S & F in replacement DC Electromagnetic Brakes all as specified as directed. |
| 76 | S & F in replacement Festoon Cable Trolley all as specified as directed. |
| 77 | S & F in replacement Brake Linings all as specified as directed. |
| 78 | S & F in replacement Electro Hydraulic Thrustor Brake all as specified as directed. |
| 79 | S & F in replacement Brake Drum & Coupling all as specified as directed. |
| 80 | S & F in replacement Rectifiers all as specified as directed. |
| 81 | S & F in replacement Electromagnetic Clutches all as specified as directed. |
| 82 | S & F in replacement Couplings all as specified as directed. |
| 83 | S & F in replacement Electromagnetic Brake Coils all as specified as directed. |
| 84 | Supplyfuse contacts complete with base form 70 A to 110 A capacity including of old fuses |
| 85 | Supplybrake shoe assemble complete (Thruster type ) with lining set suitable for main hoist of 5 ton cab for vertical drive. |
| 86 | M & L for replacement / topping up hydraullic / gear DOX EP 230 oil capacity of crane all as specified by Engineer - in - Charge. |
| 87 | Supply & Fix gasket for gear box up to 5 Ton capacity of crane all as specified as directed. |
| 88 | Supply & fix gasket for gear box for 5 to 10 Ton capacity of crane all as specified as directed. |
| 89 | Supply & Fixgasket for gear box of 20 Ton capacity of crane all as specified as directed. |
| 90 | Supply & fix pendant push buttonall as specified as directed. |
| 91 | Supply & Fixporcelain busbar insulator cylindrical type of following length:-(a) 150 mm length |
| 92 | (b) 200 mm length |
| 93 | Supplyphase indication lamp 230 V, 20 watt. |
| 94 | Supplysingle phase preventor 415 V, 3 phase. |
| 95 | Supplytime delay electro pneumatic with 2 No + 2 NC, PN type 220 volts Make. BCH or equivalent. |
| 96 | M & L for rewinding of splingring motor 415 volt, 3 phase with same cage superenamelled copper wire incl taking down & reinstalling of following capacity:-(a) 5 HP |
| 97 | (b) 7.5 HP |
| 98 | (c) 10 HP |
| 99 | Supplylimit switch (Make: SOC /EMM/BCH) of following :-(a) Normal roller lever with 3 sets of contacts type |
| 100 | (b) Puch rod snap action with 3 seats of contract type. |
| 101 | Taking down / dismantling existing perished aluminium strip of size 25 x 3 mm from any height of roof top / on walls of conventional type lightening protection network system complete all as specifiec anddirected. |
| 102 | Re-fixing old serviceable aluminium strip of size 25 x 3 mm obtained from taking down on existing PCC block at any height on roof top, on existing insulators any type on walls including jointing the system of conventional type lightening protection network and making good the disturbed surface of walls / roof top match with existing surface complete all as specified and directed and as directed. |
| 103 | Supply and fix aluminium stripof size 25x3mm fixed on PCC block with epoxy based insulator of 35mm size at distance / interval not more than 1.0 m for down conductor air terminal network including drilling two Nos holes at each joint, one set of lead washers between strips, two sets GI nut andbolt, gutties, screws etc complete all as specified and directed. . |
| 104 | Supply and fix high quality flex board showing installation details and and diagram with wood frame of size 4\"x4\" fixed in wall or outside of installation all as specified and directed |
| 105 | Material and labour (in repair) for earthing with galvanised steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground earth pit not less than 2.25 m deep below ground level with top edge of the plate not less than 1.5 m below normal ground level connected to galvanised strip 25X4 mm by means of nuts, bolts, check nuts, washers of galvanised iron or steel all as shown in electrical plate No. 03 of SSR Part I connected to earthing test point including excavation/ earth work in any type of strata, removal of surplus excavated material, GI pipe for watering and funnel, PCC 1:3:6 type C1 chamber including necessary formwork / mould for fair and even surfaces, precast RCC 1:2:4 type B0 chamber cover slab, GI funnel, with GI watering pipe 20 mm bore light grade, wire mesh, protection pipe 40 mm bore GI pipe light gde for earth lead upto 7.50 m long including testing complete all as specified and directed.Note : Test report shall be prepared and submitted by the contractor in triplicate duly obtaining signatures of MES JE / AGE & PMG / user.Test results are to be written in letters of 20mm height in white colour on black paint back ground. |
| 106 | Material and labour in replacement of GI funnel, wire mesh, earth pit Precast RCC (1:2:4) type B0 cover complete all as specified and directed. |
| 107 | Material and labour (in repair) for GI tubing light grade of size 40 mm bore for connecting to air termination rod / protection to GI strip complete tncluding Brackets for fixing all as directed and specified. |
| 108 | supply & Fixing Battery 180 AH 12V DC replacement of old unserviceable Battery at 100 t0 200 KVA DG set connected all accessories, Battery terminal, battery Led, etc complete all as specified and directed. |
| 109 | M&L for repairing ofpanel of DG set including taking down burnt circuit wiring and replacing with new wiring, changing of power contactor, modification of the panel\"s busbar with suitable rating of bus bar with nuts and bolts, colour coding sleaves for bus bar and all connected accessories all as specified and directed by Engr-in-charge. Note : Power Contactor item will be seperately under relavent item. |
| 110 | Supply and fixing in repair of ATS unit forpanel of any capacityall as specified as directed. |
| 111 | Supply and fixing in repair of 24 V, 30 A Battery charger for charging Lead Acid battery input range 170V to 270 V operating range, naturally cooled, for charging the battery all as specified as directed. |
| 112 | Comprehensive maintenance and repairs to attened break down complaints on call for goods lift one number of capacity ,(1000 Kg),Make – OMEGASl No 801059, installed at MCEA at R&DE (Engrs) Dighi Pune-15, including systematically examine lift periodically including all safety devices, selective / collective control along with control microprosser panel(V3F drive) and automatic rescue device, battery, governor, wire rope, lubricants, all doors, cabin lights intercom system, all as specified and directed all as specified and directed. |
| 113 | Comprehensive maintenance and repairs to attened break down complaints on call for goods lift one number of capacity ,(1000 Kg),Make – Kone installed at Adm building at R&DE (Engrs) Dighi Pune-15, including systematically examine lift periodically including all safety devices, selective / collective control along with control microprosser panel(V3F drive) and automatic rescue device,battery,governor,wire rope,lubricants,all doors,cabin lights,intercom all as specified and directed by Engr in charge. |
| 114 | Comprehensive maintenance and repairs to attened break down complaints on call for goods lift one number of capacity ,(1000 Kg),Make – OTIS installed at Hub building at R&DE (Engrs) Dighi Pune-15, including systematically examine lift periodically including all safety devices, selective / collective control along with control microprosser panel(V3F drive) and automatic rescue device,battery,governor,wire rope,lubricants,all doors,cabin lights,intercom all as specified and directed by Engr in charge.NOTE for Item No. 87 to 89 :-(a)All provision of Bombay lift Act as applicable shall be strictly complied with.(b)Monthly maint / servicing shall be carried out in the presence of Rep of dept. R&D Girinagar or his representative.Necessary service report to be signed by Rep of dept.(c)Any minor spares required for items coveredabove will be supplied and replaced by the firm at No extra cost.(d)Any major spares required to complete the job shall be supplied by the Department.(e)Cost of maintenance is inclusive of testing of lift from \"Lift Inspector\" once in Eleven months and necessary Test Report to be submitted by contractor to the Dept. (f)In case of any break down the firm will be informed telephonically/ telegraphically and the same will be rectified by the firm with in 24 Hrs. (g)In case of any major break down/ failure of safety measures, which can not be rectified within 24 Hrs the firm will inform Dept, Girinagar in writing and will stick stickers on each floorof lift indicating \"LIFT NOT IN SERVICE\".(h)If firm fails to attend defects with in 24 Hrs of complaint recovery of Rs- 1000.00 Per day will be recovered. |
| 115 | Supply & Fix ARD for passenger/goods lift in including removingof old ARD andmakingliftservicable for smooth functioning asdirected by Engr-in-charge. |
| 116 | Supply & Fix Door drive for 8 passenger lift in including removing of old door drive andmakingliftservicable for smooth functioning asdirected by Engr-in-charge. |
| 117 | Supply & Fix door sensor forpassenger liftincluding removing of old door sensor andmakingliftservicable for smooth functioning asdirected by Engr-in-charge. |
| 118 | Supply & Fix Main (OSG) rope 8 mm for lift, including removing of old main rope andmakingliftservicable for smooth functioning asdirected by Engr-in-charge. |
| 119 | Supply and fix in replacement of Door Shoe (Gibs) for passenger/goods lift, including removing of old Door Shoer andmakingliftservicable for smooth functioning asdirected by Engr-in-charge. |
| 120 | Supply and fix in replacement of COP display including removing old copdisplay serviceable forpassenger/goods lift &makingliftservicable for smooth functioning asdirected by Engr-in-charge. |
| 121 | Supply and fix TOUCH LESS landing operating panel complete (LOP) with digital display operate on 24 volt dc with SS plate. Complete all as specified and directed. |
| 122 | Supply and fix in replacement of 12 volt batteries for suitable Ampereandmakingliftservicable for smooth functioning asdirected by Engr-in-charge.. Make:- Exide/SF |
| 123 | Supply and fix in replacement of emergency alarm 12 volt dc complete all as specified and directed. |
| 124 | Supply and fix in replacement of landing operating panel digital display make display serviceable. |
| 125 | Supply and fix in replacement of door roller andmakingliftservicable for smooth functioning asdirected by Engr-in-charge. |
| 126 | Supply and fix in replacement of Door Accentric roller andmakingliftservicable for smooth functioning asdirected by Engr-in-charge. |
| 127 | Supply and fix contactor 110/220/440 Ac/Dc volt complete all as specified andasdirected by Engr-in-charge. Make L&T/TC/SCHNEIDER |
| 128 | Supply and fix in replacement of relay 24 volts dc andmakingliftservicable for smooth functioning asdirected by Engr-in-charge. |
| 129 | Supply and fix in replacement of LED/CFL lights complete all as specified and directed. Make:-havells/bajaj/Philips/surya. |
| 130 | Supply and fix SMPS 5 volt/12 volt/24 volt Dc. Make lift serviceable complete all as specified and directed. |
| 131 | Supply and fix Landing Door Lock for lift and make lift serviceable omplete all as specified and directed. |
| 132 | Supply and fix R CAM set for lift including removing of old R CAM making lift serviceable complete all as specified and directed. |
| 133 | Supply and fix in replacement of COP display including removing old cop display serviceable complete all as specified and directed. Make MAX/elecon |
| 134 | Supply and fix in replacement of Main Controller card (Mother Board) of control panel with all accessories. Set all parameters of card make lift serviceable complete all as specified and directed. Make:- Max/Adco/Elecon. |
| 135 | Supply and fix in replacement of Read Switch 12/24 volt dc complete all as specified and directed. |
| 136 | Supply and fix in replacement of new cabin fan as per existing make and size andmakingliftservicable for smooth functioning asdirected by Engr-in-charge. |
| 137 | Supply and fix in replacement of Relay card for Goods/Passengers Lift including removing old relay card make lift serviceableomplete all as specified and directed. |
| 138 | Rewinding of Break coil of main motor with super enameled copper winding wire of suitable gauges per existing varnishing, insulation, drying and testing complete all as specified and directed. |
| 139 | Supply and fix in replacement of limit switches complete all as specified and directed. Make MAX/TVS |
| 140 | Supply and fix in replacement of car door belt with proper adjustment of belt make lift serviceable with complete all as specified and directed. |
| 141 | Supply and fix in replacement of MCB TP 32 Amps all as specified and directed. Make schnieder/legrand/LT/ |
| 142 | Dismantling/ taking down burnt squirrel Cage Induction Motor of any capacity , 3 Phase, 415V, 1450 RPM of any make from its base and transporting the motor to the Contractor\"s workshop and back, refixing the motor at site after carrying out the following repairs/ renewals complete all as specified.-(i) opening the side covers and removing the rotor and cutting/ removing the burnt coils / winding from stator.(ii) Cleaning the slots carefully(iii) Rewinding the stator using super enamelled copper winding wire with same size, number of coils,number of turms/ coils as per data acquired from the old burnt motor, including varnishing two coats, drying and reassembling the electric motor at site(iv) Testing the coils for there continuity and no current passing through the stator core. |
| 143 | Supply and fix in replacement of Car Cabin and Counterweight Frame Shoe liner with complete all specified and directed. Make:- MAX/ADJUST |
| 144 | Rewinding of Door Motor Dismantling/ taking down burnt squirrel Cage Induction Motor of any capacity, 3 Phase, 220V, of any make from its base omplete all as specified and directed. |
| 145 | Supply and fix Main Pulley/ Deflector Pully removing old pulley make lift serviceable omplete all as specified and directed. |
| 146 | Supply and fix in replacement of TOUCH LESS car operating panel complete(COP) with digital display operate on 24 volt Dc with SS plate. Complete all as specified and directed. |
| 147 | Supply and fix in repair serial card on car top box for smooth functioning of lifts. with all connected accessories of cards and connections. Complete all as specified and directed. |
| 148 | Supply and fix in repair Governor/Governor Pulley of lift including removing oldgovernor/governor pulley make lift serviceable complete all as specified and directed. |
| 149 | Supply and fix in repair COP Switch for passengers/ Goods lift including removing old button make lift serviceable complete all as specified and directed. |
| 150 | Supply and fix in repair LOP Switch for passengers/ Goods lift including removing old button make lift serviceable complete all as specified and directed. |
| 151 | Disconnecting and taking out defective U/S main VVVF drive (any make) from existing control panel and supply and fixing new Main VVVF Drive upto existing KW complete with all electric Connection complete all as specified and directed. |
| 152 | Supply & Fix in repair Phase preventor for passenger/goods lift, including removing of old Phase preventor andmakingliftservicable for smooth functioning asdirected by Engr-in-charge. |
| 153 | Supply & Fix in repair Toe guard for lift, including removing of oldToe guardandmakingliftservicable for smooth functioning asdirected by Engr-in-charge. |
| 154 | Supply & Fix in repair Pit Switch for lift, including removing of old Pit Switch andmakingliftservicable for smooth functioning asdirected by Engr-in-charge. |
| 155 | Supply & Fix in repair Main rope 10mm forlift, including removing of old main rope andmakingliftservicable for smooth functioning asdirected by Engr-in-charge. |
| 156 | S & F in repair MCCB 160 Amps, FP, 415V, 50Hz, 36 KA confirming to IS/IEC 60947-2thermal magnetic adjustable with over load 80-100% & short circuit protection 5-10 Intypeall as directed by Engr-in-charge. |
| 157 | S&F in repair MCCB 63 Amps, FP, 415V, 50Hz, 25 KA confirming to IS/IEC 60947-2thermal magnetic adjustable with over load 80-100% & short circuit protection 5-10 Intype all as directed by Engr-in-charge. |
| 158 | S&F in repair MCB TPN 63 Amp, 16 KA`C\" seriesthermal magnetic adjustable with over load 80-100%all as directed by Engr-in-charge. |
| 159 | Supply, laying, testing and connecting in repairs LT UG cables 1100 Volt gradeXLPE insulatedand PVC sheathed, armoured, with multi stranded aluminium conductor, heavy duty confirming to IS - 1554 part-I, including cable glands, cable lugs in LT panel/ FP Box etc including material and labour for all jointing/connecting material as required, cables laid in trenches/ducts/under plinth floors passing through pipes etc, for following sizes:(a) 35 sqmm 3.5 core |
| 160 | (b) 25 sqmm 4 core |
| 161 | M & L for submain wiring alongwith earth wire in rapairs with the following sizes of FRLSPVC insulatedcopper conductor single core cable , multistranded in PVC casing/caping on the surface through with its accessories all as specified and directed by Engr-in -charge for the following (a) 2X1.5 sq mm and 1x1.5 sq mm as earth wire |
| 162 | (b) 2x2.5 sq mm and 1x2.5 sq mm as earth wire |
| 163 | (c) 2x4.0 sq mm and 1x4 sq mm as earth wire |
| 164 | M&L for lathe/machining/cutting/ surfacing complete all as required at site & dirercted by Engr-in-charge. |
| 165 | M & L for rendering1:4 cement plaster 15 mm thick on fair faces of brick work or concrete surfaces complete all as required and directed by Eng-in-charge. |
| 166 | M & L forwhite wash on new surfaces double coat all as specified and directed by Engineer-in-charge complete all as required and directed by Eng-in-charge. |
| 167 | Supply and fix in repairs outdoor type FRP junction box light weight suitable for pole mounting includin flat iron clamp duly painted with two coats of aluminium paint over a coat of red oxide primer and GI nut, bolts, washers and necessary connector for loop in loop out cable connection and suitable size galnds, of size 250x200x105 mm. |
| 168 | Supply and fix inreplacement of 3 x 1.5 sq mm PVC Circular copper cable for connection of street light fitting, Security light fitting, post top lantern and garden light fitting and including all fixing arrengenment with proper fixing all as directed by Engr in charge. |
| 169 | Dismentling and taking down existingany type ( Street light) fittingfixed on bldgs/poles /wall. |
| 170 | S & Fix LED Street light fitting 90 Watts High performance IP 66 protection and impact resistance of IK07 LED street light luminaires with complete acessories all as specified and directed by Engr In charge . |
| 171 | S & Fix LED Street light fitting60 Watts High performance IP 66 protection and impact resistance of IK07 LED street light luminaires with complete acessories all as specified and directed by Engr In charge. |
| 172 | Supply & fix LED 35W decorative post top lantern for 360 degree indirect light, made in cast aluminium with decorative opal polycarbonate diffuser with IP 65 protection, resistance to impact and corrosion, glare free and better uniformity all asspecified and directed |
| 173 | Supply and fix in repair electronic driver for LED street light fitting as per sample/existing fitting specifications complete with all accessories as suitalable for street light fitting of size 90 Watt. Note- Quoted rate include replacement of driver and testing and making fitting serviceable and upto JE/Engr-in-Charge satisfaction. |
| 174 | Supply and fix in repair electronic driver for LED street light fitting as per sample/existing fitting specifications complete with all accessories as suitalable for street light fitting of size 60 Watt.Note- Quoted rate include replacement of driver and testing and making fitting serviceable and upto JE/Engr-in-Charge satisfaction. |
| 175 | Supply and fix in repair electronic driver for LED street light fitting as per sample/existing fitting specifications complete with all accessories as suitalable for street light fitting of size 30/45 WattNote- Quoted rate include replacement of driver and testing and making fitting serviceable and upto JE/Engr-in-Charge satisfaction. |
| 176 | Supply and fixing in replacement of existing unserviceableHPSV/metal hallied lamp fitting of any wattage on existing pole with LED flood light fitting 300 watts with secondary optics made in pressure dia cast housing with heat sink and aluminium extrusion with IP66 with necessary braket ,clamps duly painted with two coats of aluminium paint over a coat of red oxide primer the quoted rate includes 7.5 mtr 3 core 6 Sqmm PVC copper cable with PVC conduit for connection, incl. bolts, nuts & washers for fixing arrangement etc complete all as specifed and directed by Engineer-in-charge. |
| 177 | Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr depth and getting out in Soft / loose soilincluding forming bottom surface etc. |
| 178 | Returning, fillingin including spreading, levelling ,watering and well ramming in layers not exceeding 25 cm thick complete in soil. |
| 179 | Removing excavated material not exceeding 50 mtr and depositing where directed at a level not exceeding 50 mtr above the starting point. |
| 180 | Material and labour for cutting of bituminous road / floor for laying of pipe / cables 45 CM wide and not exceeding 1.5meterdeep including refilling / with material and, watering well ramming / compacting and making good with PCC 1;2;4, type B-1, 100 mm thick complete all as specified anddirected by Engr-in-Charge. |
| 181 | Supply & Laying 50 mm outside dia double wall corrugated pipe (DWC) of HDPE ISI Mark for enclosing cable below ground / road surface, to a required depth, including suitable size coplers for jointing of pipe all as per site requirement |
| 182 | Boring of road for cable crossing, 60 cm below the road horizontally including all arrangement of T&P and necessary excavation etc all as directed and specified by Engr-in -charge.Note :- GI pipe will be measured and paid separately. |
| 183 | Supplying and fixingGalvanised mild steel pipe /tubing,light grade complete with all fittings of 40 mm bore dia, laid in trenches / under roads, fixed to poles/ walls with Mild steel clamps , bolts , nuts and washers as in cable protection complete all as specified and directed. |
| 184 | Supply, laying ,jointing andtesting in repairs LT underground electric power cable crossed linked XLPE insulated, two or more core galavanised steel strip or wire armoured / PVC insulated armoured cableheavy duty electric cable with aluminium conductor 1100 volts grade, cross-sectional area 16 sqmm 4 core laid in trenches / laid under floor or fixed to walls/on poles / in ducts or passing through pipesetc fixing and connecting accessories such as Aluminium cable lugs, cable glands, nut, bolts, washwers etc complete all as specified |
| 185 | Supply, laying ,jointing andtestingin repairs LT underground electric power cable crossed linked XLPE insulated, two or more core galavanised steel strip or wire armoured / PVC insulated armoured cableheavy duty electric cable with aluminium conductor 1100 volts grade, cross-sectional area 10 sqmm 4 core laid in trenches / laid under floor or fixed to walls/on poles / in ducts or passing through pipesetc fixing and connecting accessories such as Aluminium cable lugs, cable glands , nut , bolts , washwers etccomplete all as specified Note:(Excavation, earth work, sand cushioning, protection brick and pipe shall be measured and paid separately under appropriate items) |
| 186 | Material and labour for dismantling of old steel tubular pole and suppy, errectingin truly vertical position steel tubular swagedpole 9.0 mtr long with cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP 31, including painting with anti corrosive paint internally complete and externally up to planting depth, alternative white & black strips of 30 cm width upto 1.5 mtr above ground level all as required at site. |
| 187 | M&L for PCC 1:4:8 Type D2 using 40 mm graded aggregate in foundation including form work and finishing the exposed surface of concrete even and smooth complete all as specified and directed. |
| 188 | M&L for providing PCC 1:2:4 type B-1 with 20 mm graded aggregate for coping of pole complete all as specified and directed. |
| 189 | S&F in replacement of timer switch 16 Amps, 230 Volts, 24 hrs dial type for operation with by pass operation. |
| 190 | S&F in replacement of triple pole power contactor suitable for 40 Amps, with coil voltage 230 Volts. |
| 191 | M & L Painting ofsteel pole (swan neck type or straight type) up to 12 mtr heightwith cross arms, clamp of any length and shape for LT overhead line/ for street lightwith two coat of aluminium paint after scraching out old paint, cleaning and exiting surface rust free, preparation of the existing surface,including marking pole numbers in a 15 cm dia yellow circle with number writting with blacksyenthic paint/ Stricker, includingpainting strips in alternate from bottom to top with three strips of black syenthaticpaint & two strips of Yellow paint(as per existing pattern through out the circumference of pole, including removing extra wall papdi ,peel off wall papdi by sand paper and makinggood with putty as per existing thickness and applying one coat of white washing on PCC copping of pole and re-numbering of pole with approved size of letter ( Example - P- 001) with synthetic enamel paint of white colour background and black colour lettering complete all as specified and as directed. |
