Development of Sea Port Terminal at Swaraj Dweep(Havelock) in A&N Islands, (Non- schedule items, furniture & utility items.).; 1 Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinccoatingnotlessthan120gm/sqm)dulyfilledwith vermuculitebasedconcretemix,suitableformounting60 minutesfirerateddoorshutters.Theframeisfittedwith intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately). 2 Providingandfixing50mmthickglazedfireresistantdoor shutters of 60 minutes fire rating conforming to IS:3614 (Part- II), tested and certified as per laboratory approved by Engineer-in-charge,withsuitablemountingondoorframe, consistingofverticalstyles,lockrail,toprail100mmwide, bottomrail200mmwide,madeoutof16SWGG.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulationmaterialandfixingwithnecessarystainlesssteel ballbearinghingesofapprovedmake,includingapplyinga coat of approved fire resistant primer etc. all complete as per directionofEngineer-in-charge(pannelingtobepaidfor separately). 3 Providingandfixingglazinginfireresistantdoorshutters, fixed panels, ventilators and partitions etc., with G.I. beading ofappropriatesize,madeoutof20SWGG.I.sheet(zinc coating not less than 120 gm/m2), fire resistant sealant (low VOC<100g/l),includingapplyingacoatofapprovedfire resistantprimer(lowVOC<150g/l)onG.I.beadingetc., complete all as per direction of Engineer-in-charge. 4 With clear fire resistant glass panes 6mm thick of approved brand, having minimum 60 minutes fire resistance 5 Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete. 6 Providing and fixing stainless steel ( Grade 304) railing made ofHollowtubes,channels,platesetc.,includingwelding, grinding,buffing,polishingandmakingcurvature(wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side ofwaistslabwithsuitablearrangementasperapprovalof Engineer-in-charge,(forpaymentpurposeonlyweightof stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc). 7 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement:2coarsesand:4stoneaggregate10mmand downgauge),includingfinishingwithcementmortar1:3(1 cement : 3 fine sand) as per standard design : 8 In 75x75 mm deep chase 9 Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection>0.70andinitialemittance>0.75onwaterproof andslopedsurfaceofterrace,laidon20mmthickcement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto3cutscomplete,includingProvidingskirtingupto150 mm height along the parapet walls in the same manner 10 Alltheaccessorieslikegutter/flashing/cappingshallbe made from 0.50 mm TCT COLORBOND material. 11 Girth 0-305mm 12 Girth 306-610mm 13 ProvidingandfixingDORMAleveractionflushboltwith 19mmprojectingboltL=172mmforwooddoorinsatin chrome 14 DORMA 1 point panic device in Contur design, push bar for single door for fire and smoke check doors, with steel latch, securityanti thrust latch for door widths upto 1300mm, consistingof2102F,2105insilverfinish.AsperEN1125, CE marked 15 Providing & fixing of DORMA pull Handle TGDI-D300 back to back with adjustable fixing for glass, wood and metal doors in satin stainless steel. The pull handles should have supporting washer with raised bevelling on the outer surface. Length =300mm, 22mm dia, -SS304 16 Providing&fixingofDORMA4012wallmounteddoorstop dome with 60mm length with fixing accessories 17 SINGLE GLAZED TOUGHENED GLASS PARTITIONS - WITH ALEXA SYSTEM-100 FRAME PROFILES SingleGlazedGlasspartitionof10mmToughenedGlass usingDORMAAlexaSystem-100Framestoaheightof maximum 4m or as per drawing. with DORMA Alexa BP100 Profiles & Alexa SP100 .The profile size to be 100x25MM to be fixed on to the floor/wall/ ceiling.DORMA Alexa H Junction profile,90DegLJunctionProfilesandTJunctionprofiles. TheAlexaprofilesshallbesuitableforGlassthicknessof 10/12/13.52mm.The Profile shall be matt natural anodized.All Profilestobewith2mmGaugethicknessExcluding20 Micron of Anodizing. Note:For overall panel Alexa OHP100 Overpanel Profile to be used.andforOpenglassedgesEP100EndProfiletobe used. 18 Handicap kit (Australian Version) 19 Disablesignplate3040-DforWCapplicationwithfixing screws size 125 x 125mm, rounded corners in SS 304 satin stainless steel finish. Marking in black 20 ProvidingandPlacinginpositionsuitablePVCwaterstops conformingtoIS:12200forconstruction/expansionjoints betweentwoRCCmembersandfixedtothereinforcement with binding wire before pouring concrete etc. complete : 21 Serrated with central bulb (225 mm wide, 8-11 mm thick) 22 Providingandlayingwaterproofingtreatmentonroofsof slabs by applying cement slurry mixed with water proofing 23 (a) after surface preparation, first layer of slurry of cement @ 0.488kg/sqmmixedwithwaterproofingcementcompound @ 0.253 kg/sqm. 24 (b)layingsecondlayerofFibreglassclothwhenthefirst layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. 25 (c)thirdlayerof1.5mmthicknessconsistingofslurryof cement@1.289kg/sqmmixedwithwaterproofingcement compound @ 0.670 kg/sqm and coarse sand @1.289 kg/sqm. This will be allowed to air cure for 4 hours followed bywatercuringfor48hours.Theentiretreatmentwillbe taken upto 30 cm on parapet wall and tucked into groove in parapet all around. 26 (d) fourth and final layer of terrazzo tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured. 27 Providing and applying two component ACRYLIC POLYMER MODIFIEDCEMENTITIOUSflexiblewaterproofing,Dr.Fixit Fastflex. The systemincludesbase preparationof cleaning, brushing and removal of flacky materials, grouting the porous areawithcementitiousgrout,propercovingbetweenslab and wall junctions and applying Dr.Fixit Fastflex in two coats @0.75kg/Sqm/Coat.Coatingshallbedoneontheentire horizontalsurface,verticalsurfacecompleteasper manufacturers methodology and specification.or equivalent approved makes . pidlite mykschomburg / fosroc 28 Providingandapplyingpolymericwaterproofplasteringwith CM1:4ofthickness20mmforwallsadmixedwithDrFixit Pidiproof LW+ @ 0.2litre/bag of cement as per manufacturersspecifications including curing etc. complete orequivalent approvedmakes .pidlite mykschomburg/fosroc 29 Supplying and applying of two coats of epoxy resin Dr. Fixit Dampguard@500gm/Sqm.(intwocoats@250 gm/Sqm/Coat). or equivalent approved makes . pidlite mykschomburg / fosroc 30 Providing and fixingin position pre-cast RCC. Manhole cover and frame of required shape and approved Quality. 31 Rectangular shape 600x450 mm internal dimensions. 32 Providingorangecoloursafetyfootrestofminimum6mm thickplasticencapsulated asperIS : 10910, on 12 mm dia steelbarconformingtoIS:1786,havingminimumcross sectionas23mmx25mmandoverallminimumlength263 mmandwidthas165mmwithminimum112mmspace betweenprotrudedlegshaving2mmtread ontopsurface byribbingorchequeringbesidesnecessaryand adequate anchoringprojections ontaillengthon138mm asper standard drawing and suitable to with stand the bend test and chemicalresistancetestasperspecificationsandhaving manufacturespermanentidentificationmarktobevisible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20 mm nominal size) complete as per design. 33 Providing and fixing Floor clean out plugs with two nos of SS screwsofapproveddesignincludingsettinginfloorwith cementmortortomatchwithfloorfinsishasperarchitect requirement 34 ProvidingandfixingNahaniFloortrapwithSSgratingof approved make with water seal, including jointing, cutting and making good the walls, floors, etc all complete as per specifications 35 Designing and constructing concrete solid blockchamber of thefollowing sizes in cc masonry workin cement mortar 1:5 R.C.C. top slab, both inside and outside of plastering 12 mm thickwith cement motor with a floating coat of neat cement oninsideface,properwaterproofingtoensurenoground water seepage in the manhole, including necessary centering and shuttering, reinforcement, excavation, inall kindof soil, dewatering,refilling, watering,rammingandremovingthe surplus excavated earth, making good the same complete as required. Cost shall be inclusive of 600 x 600 mm DI Manhole cover with frame, Medium Duty (B-125), Wt 62 kg 36 900 x 800 x 900 mm size 37 “Supply and installation of colour coated trapezoidal TRIMDEKe 1015 profile sheet of 1015 mm at work site at Swaraj Dweep, the effective cover width and nominal 28 mm deep ribs with subtle square fluting in the five pan at nominal 200 mm centre-to-centre. The end rib shall be designed for anti-capillary action, to avoid any seepage of water through the lateral overlap. The feed material is manufactured out of nominal 0.15 mm Base Metal Thickness (BMT) & 0.53mm (TPT), Hi-Tensile steel with min. 550 MPa yield strength, metallic hot dip coated with Zinc-Aluminium alloy (i.e. 55% AI, 43.4% Zinc, 1.6% Si - Zincalume), AZ150 (min 150 gm/m2 total on both side), pre-painted with Super Durable Polyester Colorbond XRW quality paint includes inorganic infrared reflective pigment (High SRI-”Thermatech technology”)of 20pm exterior coat on top surface and Sqm reverse coat on back surface over Sqm primer coat on both surfaces of approvecl color shade fry concern authority. The sheet conforms to general requirement of AS/NZS 2728 type 4 / IS 15965 class 3 durability andglossvalueof 25%-400/oof TataBlueScopeSteelmake.The steel manufacturers test certificate for the chemical and mechanical properties of steel must be submitted for approval by the concerned authority prior to installation. The steel sheet shall be fixed to purlin bymeans of fasteners with nominal 40kmzinccoated or nominal 25 pm zinc-tin alloy coated, Hex head, self-drilling screw (AS3566-2002- class 4)as perfasteners of approved make (Buildex,Roofexor equivalent) with EPDM washer and screw caps as per the requirement considering the profile shape and design load. The fastener size shall be calculated asperthe design ormanufacturers recommendations. The profile sheet, fastener size etc. shall be approved by the concern authority. The measurement shall be based on finished/covered surface area. The rates shall be including Crimping the sheets to the required profile,EPDM washer, AS3566-2002- class 4 fasteners, transportationcharges ofall materials to site, installation at site, GST, Labour Cess, all labour charges, minor tools and plants etc. complete.” 38 SPIDER GLAZING( Truss fitting with 13.52mm Reflective Laminated T.G) Design supply andinstallation of Dormakaba Rodan Series Truss fitting Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III) and Seismic load Calculation. The System held with Rodan Series Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having13.52mm Reflective Laminated toughened glass(6mm Clear toughened glass + 1.52mm pvb + 6mm reflective toughened glass) held together with Diamater of 141mm and 5.5mm thick SS- 316 Grade Stainless steel Pipe, articulated Spider and bolt assembly with SS Support. All complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion and seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter andU channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof and dust proof. The rate shall include all design, Engineering and shop drawing, labour, including wastage, enabling temporary services all fitting fixers nut bolts, washer, fastener, anchors. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured. 39 Providing and fixing Jaquar make chromium plated brass pillar tap, model OPP-CHR-15001PM or equivalent as approved by Engineer in charge, suitable for wash basins, with single lever operation, foam flow aerator, conforming to IS standards and manufacturer’s specifications. The rate includes cost of all materials, labour, tools and plants, including cutting and threading of supply pipe, making water-tight connection with basin inlet, testing for leakage, and cleaning after installation, complete as per direction of Engineer-in-Charge. 40 Providing and fixing isolated wall-mounted mirror of size as specified (typically 1000x600 mm or larger), 5 mm thick float glass mirror with beveled/polished edges, mounted on the wall using stainless steel dome-head bolts with rubber buffers at rear for spacing, of approved design and make such as Saint-Gobain, Modiguard, or equivalent. The mirror shall be fixed without frame, giving a floating appearance, with minimum 4 nos. SS screws/bolts (grade 304), anchored through pre-drilled mirror holes using chrome-plated caps and nylon sleeves, including neoprene washers for shock absorption. The rear gap shall allow ventilation to prevent moisture buildup and deformation. The work includes: – Drilling wall surface with proper marking and leveling – Fixing the mirror using rust-proof SS fasteners with protective washers – Ensuring plumb installation with edge protection and soft backing as required – Cleaning the mirror and surrounding surfaces after installation – Handing over in scratch-free, spotless condition, complete as per direction of Engineer-in-Charge. 41 Providing and fixing wall-hung European water closet (EWC) of Jaquar make or equivalent, Model: CNS-WHT-961UF or equivalent (wall-hung WC with UF seat cover), including fixing with suitable stainless steel brackets, bolts, and accessories, connected to concealed cistern and control plate assembly. The flushing system shall include Jaquar or equivalent single piece slim concealed cistern body Model: JCS-WHT-2400S and Control Plate Model: JCP-CHR-2415, or equivalent, suitable for dual flush operation (3/6 litres). EWC approx. size: 550 mm (L) × 360 mm (W), made of vitreous china, white colour, conforming to IS:2556 with P-trap/ S-trap connection as per site requirement. The concealed cistern body shall be factory-tested, slim profile for in-wall mounting with powder-coated steel frame, adjustable flushing volume, integrated stop valve, and inlet connection. The control plate shall be made of chrome-plated brass/ABS material with soft-touch dual push buttons. The work includes secure fixing of WC pan, installation of cistern and control plate, connection with inlet water pipeline (20 mm dia CPVC/GI) and outlet waste pipe (110 mm dia), complete with cutting, chasing, grouting, alignment, leak testing, and making good the walls/floors. All hardware shall be concealed and stainless steel (SS-304 grade), and installation shall be in accordance with manufacturer’s specifications and approved shop drawings. The rate includes supply, installation, testing, flushing operation, alignment, and final cleaning, complete in all respects as per direction of Engineer-in-Charge. 42 Supplying Fixing, testing commissioning ofstoragetype water heater of 15 lts approved shade with copper container, glasswoolinsulation,stoveenamelledM.Sjacket, thermostatically controlled inner heater with pilot neon lamps, angle valve on inlet connection, 15mm dia C.P flexible connection pipe in inlet & outlet suitable for working pressure of 5 kg/sqcm complete as required. Make : Jaguar or equivalant. 43 Providing, fixing, jointing and testing in position the following UPVCpipes Agri pipesconfirmingtoIS:4985of6Kg/ Sq.cm for drainage system cut to required length.Pipe to be laidbelowgroundlevelintrenchesuptorequireddepth including excavation in all kind of soil 44 200mm dia 45 250mm dia 46 Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. 47 Providing and installing aluminium baffle ceiling system, consisting of aluminium baffles of size 100mm × 25mm × 1.5mm (or as specified), with a powder-coated/anodized finish in approved color, suspended from the structural ceiling using a GI/MS framework with adjustable suspension rods, including all necessary hardware, alignment, leveling, cutting, and finishing, complete as per the direction of the Engineer-in-Charge. 48 Providing & Fixing of Armstrong or Equivalent Mineral Fibre Acoustical Suspended Ceiling System with Classic Lite (Tegular) Edge Tiles With Armstrong 24mm Exposed GRID.The tiles should have Humidity Resistance (RH) of 99%, NRC 0.5, Light Reflectance ≥87%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Colour White, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 &7) in module size of 600 x 600 x 16mm , suitable for Green Building application, with Recycled content of 30%. The tile shall be laid on Armstrong Prelude32 with 24 mm wide T - section flanges colour white having 1tary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm cross Tees with a web height of 32mm and a load carrying capacity of 7.05Kgs/M2 & pull out strength of 100kgs.. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with suspension sydtem of Armstrong make. orequivalent. The Tile & Grid system used together should carry a 30 year warranty. INSTALLATION: To comprise main runner spaced at 1200mm centres securely fixed to the structural soffit using Armstrong suspension system (specifications below) at 1200mm maximum centre.The First/Last Armstrong suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall.Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module.Cut cross tees longer than 600mm require independent support.600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. PeriMetre trim to be Armstrong wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centres. Armstrong SUSPENSION SYSTEM accessories manufactured and supplied by Armstrong World Industries orequivalent consisting of M6 Anchor Fasteners with Vertical Hangers made of Galvanised steel of size 26 x 26 x 25 x 1.2mm with a Galvanised Thickness of 80gsm, A pre Straightened Hanger wire of dia – 2.5 mm of 1.8 m length., thickness of 80gsm and a tensile strength of 344-413 MPa, along with Adjustable hook clips of 0.8mm thick, galvanised spring steel for 2.68 mm with a minimum pull strength of 110 kg. The adjustable clip also consists of a 3.5 mm aquiline wire to be used with the main runner. 49 ARMSTRONG OR EQUIVALENT MINERAL FIBRE ACOUSTICAL SUSPENDED CEILING SYSTEM (600X1200) 50 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 TypeA, including jointing with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion,(I)single socketed pipes 51 160mm dia Metre 52 Providing and fixing on wall face unplasticised Rigid PVC moulded fittings /accessories for un plasticised Rigid PVC rain water pipes conforming to IS:13592 TypeA, including jointing with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion. 53 160mm bend 54 160mm coupler 55 Design, supply, and installation of handrail system using Dormakaba bottom rail of section size 125 mm × 60 mm, fixed on floor with necessary anchor bolts, including top rail made of 50 mm diameter stainless steel slotted pipe inserted into the top edge of glass. Both top and bottom rails shall be in Cool Champagne anodized finish, or powder-coated finish as approved by Engineer-in-Charge. Glass infill shall be 13.52 mm thick clear laminated toughened glass (comprising 6 mm thick clear toughened glass + 1.52 mm PVB interlayer + 6 mm thick clear toughened glass), fixed firmly within the bottom rail using approved gaskets and seals. All fixing accessories such as anchor bolts, nuts, bolts, fasteners, washers, buffer plates, rubber gaskets, spacers, and necessary hardware shall be included in the rate. All stainless steel components shall be of SS-304 grade. The system shall be installed with proper alignment and level, and the gap between glass-to-glass and glass-to-wall shall be minimum 20 mm, sealed with non-staining structural silicone sealant to ensure weather resistance and flexibility. All materials, accessories, labour, tools & plants, scaffolding, transportation, etc., required for the complete execution of work shall be included in the rate. Note: The quoted rate shall be inclusive of all operations, fittings, installation, surface cleaning, and handing over of the work in neat and finished condition. 56 Providing, fabricating, supplying, and installing frameless overhead glass canopy using laminated toughened safety glass of 6mm + 6mm thickness with 1.52mm PVB interlayer (total thickness 13.52mm), supported by a system of stainless steel (SS 304/316) point-fixed spider fittings, tension rods, brackets, and wall-mounted anchors, complete with necessary structural supports, sealants, gaskets, and waterproofing treatments. The work includes all associated components like stainless steel hardware, drilling, embedding, grouting of anchors, proper slope for rainwater runoff, cleaning, polishing, scaffolding, structural design verification, and restoration of disturbed surfaces. Installation shall be done as per architectural drawings, structural engineers guidance, manufacturer’s specification, relevant IS codes, and to the complete satisfaction of the Engineer-in-Charge. 57 Providing, fabricating, transporting, and installing fully frameless swing-type glass door system using 12mm thick toughened float glass panels, with all edges machine-polished and beveled, including supply and installation of heavy-duty double-action floor spring mechanism, stainless steel patch fittings (top, bottom, and corner), top pivot, door stopper, door handles, patch lock (if required), alignment brackets, cover plates, and all other necessary accessories and fixtures. The work shall also include cutting, leveling, drilling in floors and walls for anchoring, embedding fittings, applying silicone sealants where required, and making good the disturbed surfaces to original condition. The installation shall be done with proper vertical and horizontal alignment, ensuring smooth, noise-free opening and closing, complete as per approved shop drawings, manufacturer’s recommendations, and as directed by the Engineer-in-Charge. 58 Providing, fabricating, transporting and fixing in position stainless steel guard rail near glass areas, exposed columns, balconies, corridors, or similar locations, comprising vertical posts of stainless steel grade 304, hollow sections (minimum size 40mm dia,2.0 mm thick),SS flatheight - 150 mm withand anchor bolts or as per approved drawing), spaced at standard intervals not exceeding 1000 mm center to center, and a single continuous horizontal rail of 50mm diameter stainless steel pipe, including base plates, cover flanges, expansion bolts or chemical anchors for secure fixing, necessary welding, grinding, buffing, and polishing to satin (No. 4) finish, all complete as per architectural drawings and instructions of Engineer-in-Charge. The rate shall include: Cost of all labour and materials, Fabrication in workshop or at site, Transportation to site, Loading and unloading, Erection and installation at designated locations (including on RCC, tile, or granite floors), Drilling, grouting, fixing with stainless steel fasteners or chemical anchoring as required, Finishing and making good surrounding surfaces after installation, Polishing to uniform satin finish, All fittings, consumables, tools, scaffolding, safety equipment, etc.,Applicable Goods and Services Tax (GST), Labour Welfare Cess (LWC) at applicable rate, All duties, taxes, freight, toll, royalties, and incidental charges. 59 Providing and fixing chromium-plated brass waste coupling of 32 mm or 40 mm nominal bore (as specified), heavy-duty, full threaded type, with inner and outer brass washer rings, rubber gasket, and chrome-plated dome/flat cover, of approved make such as Jaquar (Cat. No. ALD-705 or ALD-705L), Kohler, ESS ESS, or equivalent, conforming to IS specifications. Waste coupling shall be fixed with white cement or thread seal tape to ensure leak-proof joint between sanitary ware and the outlet pipe. The item includes removal of burrs, tightening, cleaning after installation, leak testing and final handing over in working condition, complete in all respects as per the direction of Engineer-in-Charge. 60 Providing and fixing heavy-duty chromium plated brass bottle trap of 32 mm or 40 mm nominal bore (as specified), of approved make such as Jaquar (Cat. No. ALD-769 or PRS-CHR-769L), ESS ESS, Kohler, or equivalent, including all accessories like wall flange, extension tube, slip joints, rubber washers, and chrome nut, suitable for installation with wash basin or counter basin outlet. The bottle trap shall be fixed to the waste coupling and connected to the outlet pipe using appropriate seals to ensure leak-proof and odor-proof performance. The trap shall have a minimum bottle depth of 75 mm, removable base cap for easy cleaning, and anti-corrosive, tarnish-resistant surface finish. The work includes proper alignment, leak testing, and final cleaning, all complete as per manufacturer’s specifications and direction of Engineer-in-Charge. 61 Providing and fixing wall-mounted soap dispenser with frosted/clear glass bottle and chromium-plated brass holder and pump mechanism, of approved make and design such as Jaquar Cat. No. AKP-35731P, Kohler, Grohe, or equivalent, including all necessary mounting hardware, stainless steel screws, wall plugs, and chrome-plated cover plate for concealed fixing. The dispenser bottle shall have a minimum capacity of 200–250 ml, easily refillable from the top, and corrosion-resistant pump head. The item includes drilling holes in the wall, fixing the bracket in plumb, testing the pump action, cleaning after installation, and handing over the unit in complete working condition as per manufacturer’s instructions and direction of Engineer-in-Charge. 62 Providing and fixing wall-mounted, automatic electric hand dryer of approved make such as Dyson, Euronics, Dolphy, or equivalent, made of high-impact ABS plastic or stainless steel body, suitable for 230V, 50Hz single-phase AC supply, with automatic infrared sensor-based operation. The hand dryer shall have minimum power consumption of 1000–1800 W, air speed not less than 80–90 m/s, and drying time of 10–15 seconds. Unit shall include thermal cut-off, auto shut-off mechanism, and safety protections as per CE/IS standards. The work includes: – Mounting the unit with appropriate brackets and fasteners – Electrical connections using 3-core flexible cable up to nearest switch/socket point (within 1.5 m) – Testing for safe operation, alignment, and wall finish repair if required – Cleaning and handing over the unit in working condition, complete as per manufacturer’s specifications and direction of Engineer-in-Charge. 63 Providing and fixing wall-mounted paper towel dispenser made of high-quality ABS plastic / stainless steel (Grade SS-304), suitable for single sheet interfold / multi-fold paper towels. Unit shall have a lockable front cover with transparent or indicator window for level monitoring, and an easy-access refill mechanism. Dispenser to be suitable for commercial washroom use, capable of holding approximately 200–400 paper towel sheets, with controlled dispensing to reduce wastage. Dispenser body shall be scratch-resistant, moisture-resistant, corrosion-free, and designed for hygienic, touch-free dispensing. Overall approximate dimensions: – Height: 250–300 mm – Width: 250–300 mm – Depth: 100–130 mm Unit shall be mounted on the wall using stainless steel screws and nylon plugs, at a comfortable reach height above washbasin or near handwashing area. Of approved make such as Kimberly-Clark, Dolphin, Cera, Jaquar, Toshi, Euronics, or equivalent as approved by Engineer-in-Charge 64 Providing and fixing factory-made modular toilet cubicle partition system made of 12 mm thick compact high-pressure laminate (HPL) boards / solid phenolic core panels, anti-bacterial, fire-retardant, water-resistant, termite-proof and graffiti-resistant, in approved colour, finish and pattern. Each cubicle shall include side panels, doors, pilasters, and intermediate partitions (where required), all machine-cut with chamfered and polished edges. The panels shall be fixed using heavy-duty stainless steel (SS 304 or SS 316 grade) hardware including top rail (aluminium or SS), U-channels, wall and floor brackets, hinges (gravity-based or spring-loaded), door knobs/locks (indicator type), coat hook, door stoppers, adjustable foot supports, and necessary joinery fixtures. Doors shall have minimum 150 mm floor clearance and soft-close hinges. All components to be rustproof and designed for high-traffic public use. Panels and doors shall be installed true to line, level, and plumb, with proper alignment and adequate support. All fixtures shall be securely anchored with nylon plugs/SS screws and fasteners. The work includes preparation of surface, layout, delivery, installation, site cleaning, and handover, all complete as per approved architectural drawings and direction of Engineer-in-Charge. 65 Providing and fixing urinal modesty partition panel made of 12 mm thick compact high-pressure laminate (HPL) board / solid phenolic resin-based board, water-resistant, termite-proof, and anti-bacterial, in approved colour, shade and finish (matte or textured), cut to required size (typically 450 mm x 900 mm or as approved), fixed with heavy-duty stainless steel (SS 304/316 grade) brackets, U-channels, and fasteners. All exposed edges to be chamfered and machine-polished. Panels shall be fixed to wall using SS wall brackets and supported with SS floor-mounted leg brackets (if height exceeds 900 mm) ensuring rigidity and smooth finish. All accessories including SS screws, washers, brackets, nylon wall plugs, and corner profiles shall be included. The installation shall be done in line and level, plumb and true to layout, as per manufacturer’s specifications and approved architectural drawings. Measurement shall be on the basis of number of panels fixed. Rate shall include all labour, materials, brackets, edge finishing, fixtures, fasteners, scaffolding, and cleaning, complete in all respects to the satisfaction of Engineer-in-Charge. 66 Supplying,installing,fixing,jointing,testingand commissioning of approved make Chlorinated Polyvinyl Chloride pipes (CPVC) up to 50 mm dia SDR.11, ASTM CTS, andabove50mmdiaCPVCschedule40/80ASTMIPS. Fittingsupto50mmdiaSDR11.The fittingsand specials suchastees,elbows,couplers,bends,enlargersetc.,with CPVC brass threaded combination / transition specials such asmaleadaptersbrassthreadedfemaleadapters,brass FPT Tee, Brass FPT elbow etc., where connection with metal istobemadeincludingnecessarydrillingholes,chasing wallsandmakingthesamegoodingerumixedcement mortar1:1restorethesameoriginalconditionneatlyas directedbytheEngineerin-charge.Jointstobemadewith CPVC solvent cement up to 50 mm dia as per ASTM D-2846 and above 50 mm dia primer P-70, and solvent confirming to ASTMF-4931 / 724. 67 80 mm dia 68 100 mm dia 69 Supply,fixing,testingandcommissioningofNonreturn valve of ball typeworkingpressure not less than PN10 with threaded / flangedjointscompletewith nuts,bolts, gaskets, washers etc. 70 100MM 71 Designing and constructing concrete solid blockchamber of thefollowing sizes in cc masonry workin cement mortar 1:5 R.C.C. top slab, both inside and outside of plastering 12 mm thickwith cement motor with a floating coat of neat cement oninsideface,properwaterproofingtoensurenoground water seepage in the manhole, including necessary centering and shuttering, reinforcement, excavation, inall kindof soil, dewatering,refilling, watering,rammingandremovingthe surplus excavated earth, making good the same complete as required. Cost shall be inclusive of 600 x 600 mm DI Manhole cover with frame, Medium Duty (B-125), Wt 62 kg 72 900mm dia 73 Constructingconcret solid block masonry road gully chamber 50x45x60 cm withsolid blocks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design .Both inside and outside of plastering 12 mm thickwith cement motor with a floating coat of neat cement oninsideface,properwaterproofingtoensurenoground water seepage in the manhole, including necessary centering and shuttering, reinforcement, excavation, inall kindof soil, dewatering,refilling, watering,rammingandremovingthe surplus excavated earth, making good the same complete as required. 74 Providing fixing testing and commissioning of Silencio pipes inthekitchendrainageofthefollowingsizesincludingall necessary specials, like P trap, elbows tees, solvents, gaskets etc completetothesatisfactionofengineer -in-charge. 75 75mm 76 110mm 77 Providing and fixing stainless steel cladding over exposed RCC/steel columns using high-quality stainless steel sheets of gradeSS 316 for coastal/humid environments), minimum 2.0 mm thick, with satin/mirror/brushed finish (as approved), bent and fabricated in curved or segmented profile to suit the column shape. Cladding shall be pre-formed and modular, installed using concealed stainless steel framing system, cleats, anchor fasteners, and adjustable brackets, ensuring rigid fixing and alignment. The cladding system shall include: (a) Base and top trims/caps, (b) Horizontal and vertical edge profiles, (c) Thermal insulation (if specified), and (d) Neoprene or rubber gaskets for expansion/movement control (as required). All joints shall be butt-jointed or overlapped with minimum visible gaps, properly sealed to prevent ingress of moisture/dust. Stainless steel surface shall be protected with factory-applied PVC film, which shall be removed only after completion of installation. All panels shall be free from dents, scratches, waviness, or sharp edges. The work includes preparation of surface, provision of framing/back support (MS/Aluminium as per design), drilling, anchoring, leveling, cleaning, protection of adjacent finishes, and handing over the work complete in all respects as per drawings, specifications, and direction of the Engineer-in-Charge. 78 Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. 79 Design, supply, installation, testing and commissioning of Reverse Osmosis (RO) Plant of capacity 250 litres per hour (LPH) complete with pretreatment unit, high-pressure pump, micron filtration unit, RO membrane, flow meters, pressure gauges, electrical control panel, fully automatic flushing mechanism. The system shall be skid-mounted, suitable for indoor installation, and capable of operating at ambient temperatures and varying TDS levels. It shall include all accessories such as PVC/SS piping, valves, dosing pumps, pressure relief valve, raw water feed pump, concentrate reject line, product water outlet, and other necessary fittings. The entire system shall be designed to deliver potable quality water conforming to BIS 10500 standards. The plant shall be complete in all respects including: Electrical wiring from control panel to motors and sensors Structural support frame in SS or powder-coated MS Commissioning with trial run . Operation and maintenance manual and warranty certificate All works shall be carried out as per manufacturer’s specifications and approved design/drawings to the satisfaction of Engineer-in-Charge. Make/Model: Kent / Zero B / Ion Exchange / Thermax / Blue Star or equivalent approved make. 80 Supplying, installing, testing and commissioning of floor-mounted electric water cooler of capacity 80 litres storage tank and cooling capacity 80 to 120 litres per hour, with SS-304 grade stainless steel inner tank, PUF insulation, powder-coated outer body, push-type SS taps (minimum 2 Nos.), drain outlet, copper cooling coil with epoxy coating, service panel, adjustable legs, and all internal electrical fittings conforming to IS standards. Water cooler should be suitable for connection to central RO line or treated water supply. Complete including all materials, labour, tools & tackles, transportation, installation, connection to power and water source, testing, commissioning and handing over as per manufacturer’s specifications and direction of Engineer-in-Charge. Make: Voltas Model FSS 80/80 PSS / Blue Star SDLx480 / or equivalent. 81 Supply, fixing, testing and commissioning ofuPVC pipes for waste pipes as per IS 4985: 2000of 6 kg/cm2 and moulded/fabricatedfittings withsolventcementjoint. Includes fittings (plain or door) tees, bends, collars, crosses, reducers etc.and making good the walls etc. for concealed pipe and testing of pipelines, etc all complete as per specifications. Location:Outlet from WB,Sink 82 a) 40 mm dia. 83 b) 50 mm dia. 84 Supplying,fixingandtestingandcommissioningofUPVC soil,wasteandventpipes(SWR)confirmingtoIS13592 :1990, type B with solvent cement inclusive of all necessary specials like bends, tees, offsets, doorbends, junctions, cowls,etc.,laidunderfloor/fixed onwalls,andinpipe shafts etc., complete. Location:Inside Toilet 85 a) 75mm dia 86 b) 110mm dia 87 Supplying,fixingandtestingandcommissioningofUPVC soil,wasteandventpipes(SWR)confirmingtoIS13592 :1990, type B with rubber ring joint inclusive of all necessary specialslikebends,tees,offsets,doorbends,junctions, cowls,etc.,laidunderfloor/fixed onwalls,andinpipe shafts etc., complete. Location:Shaft and above ceiling 88 a) 75mm dia 89 b) 110mm dia 90 Providing and fixing chromium plated brass/metal square towel ring of approved design, shape and make such as Jaquar (Cat. No. ACN-1121N or similar), Kohler, ESS ESS, or equivalent, including concealed fixing arrangement with brass screws and wall plugs, stainless steel mounting plate, and chrome-plated cover plate to hide the fixtures. The item includes marking on the wall, drilling holes, fixing the ring firmly in true level and alignment, cleaning the surface after installation, and handing over in neat condition, all complete as per manufacturer’s instructions and direction of Engineer-in-Charge. 91 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 92 100mm dia nominal bore 93 Supplying installation and commissioning of terminal chair without charging point with the following specifications Generic and Dimensional Requirements The chair unit will feature three individual seats with integrated armrests and backrests, ensuring a combined seating and back support configuration. It will not include a table. In terms of dimensions, the overall length, including armrests, must be atleast 1655 mm. The overall height, measured from the floor to the top of the backrest, needs to be a minimum of 850 mm. The floor to seat height, taken from the ground to the front of the seat, should be no less than 425 mm. Each seat will have a minimum depth of 450 mm and a minimum width of 485 mm. Main Frame Specifications The mainframe of the chair will be constructed from extruded aluminum, with a material thickness ranging from 4.0 mm to 4.5 mm. The supports for the mainframe, acting as the base or legs, will be made from aluminum die-cast. These supports will have a powder-coated finish of 50 microns, with a silver color family. Additionally, a soft-grip feature will be present at the bottom of the mainframe supports to enhance stability and protect flooring. Chair Seat and Backrest Details Each chair seat will be crafted from PU foam without any inserts, and it will be integrated directly into the frame. The material thickness for the seat will be between 1.0 mm and 1.5 mm. There will be no separate cushions or foam on the seat; the integrated PU foam will have a density between 350 and 400. The chair seat frame will be in the black color family. Similarly, the chair backrest will also be made of PU foam without inserts, integrated into the frame, with a thickness ranging from 22 mm to 25 mm. It will feature a full-back configuration, and like the seat, it will not have separate cushions or foam. The integrated PU foam in the backrest will also have a density between 350 and 400. The chair backrest frame will also be in the black color family. Armrest Specifications The chair unit will include armrests at both extreme ends and a common armrest between each seat. These armrests will be constructed from aluminum die-cast, with a material thickness between 3.5 mm and 4.0 mm. There will be no padding on the armrests, and their color family will be silver. Warranty - 12 months. Make- Godrej Luft or equivalent as approved by EIC. 94 Supply, fitting and fixing of Bed with Side Tables- Queen Size bed with external dimension bed 2.05 m x 1.57 m with upholstered headboard and no storageand total 400 mm box height made of 19mmcommercial board with teak ply finishing. Head board with 100mm or moreteak wood boarder & centre fixed with upholstered cushion (approvedshade fabric/ leatherite) complete finished with melamine polishing. Make Godrej or equivalant. 95 Supply, fitting and fixing of Wardrobe - Modular wooden wardrobe of sizeof size 2400x1800 mm made of 18mm thick HDHMR board (action Tessa/ Green/ Century) with inner side 1mmthick laminate. The edges of the box is to be fixed with PVC edge bend of 0.8mm thick with adhesive (hot melt). The complete box shall be assembled with mini-fix. It further includes the cost of 4 Nos legs 4 high. It also includes skirting in front of cabinet bottom. Outer finishedwith 6mm thick teak ply. Inside to be provided with one hanger rode, one drawer with lock and required shelves. Shutters complete with 10 SS finish handles and auto hinges. Finished in melamine polish. List of Approved Makes: Godrej, HermanMiller, Steelcase, Dellform, Vitra” . Product should be Greenguard-UL certified. 96 Supply and fixing of Mattress -Dark Fabric Preferred Supply, of Mattress 78 X 60 X 6 inches of Godrej consisting of mattress for a sound sleep. It boasts of a combination of Bonnell spring for a great support and PU foam quilting for better cushioning,supple feel and comfort. Foamedges used on the side walls provide support on the edges to avoid bending and damage & thus increases durability. Manufactured with Premium Quality materials as per direction and satisfaction of Engg.-in-charge. Make Godrej or equivalant. 97 Supply, fitting and fixing of 3- Seater Sofa: (S3-CMR)SEAT FOAM :The seat is made of PUfoam with Density28 ±2kg / cu . mtr having anadditional top layer of super softPU foam inDensity32 ±2kg / cu . upholstered with fabricor leatherette .2BACKFOAM :The back ismade of PU foam withDensity28±2kg / cu . mtr with two additionaltop layer of supersoft foam of density32 ± 2kg / cu .mtr ,upholstered with fabric or leatherette .UNDERSTRUCTRE: Understructure is madeup of1 . 2 ± 0 . 1cm .thickhot pressed plywood( moisture resistance & termite proof as per IS: 303) & pinewood of cross section devoid of major knots & surface defects 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose 6 nos. per seat &3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. LEGASSEMBLY :It isa welded assemblymade in Stainless steel( grade SS202 )tube&platewith plastic endcap. (W)206.0* (D) 90.5(H) 85.5 cmseat (H) 45.0 cm.Make Godrej or equivalant. 98 Supply, fitting and fixing of 2- Seater Sofa :(S2-L1) SEAT FOAM :The seat is made of PUfoam with Density28 ±2kg / cu . mtr having anadditional top layer of super softPU foam inDensity32 ±2kg / cu . upholstered with fabricor leatherette .2BACKFOAM :The back ismade of PU foam withDensity28±2kg / cu . mtr with two additionaltop layer of supersoft foam of density32 ± 2kg / cu .mtr ,upholstered with fabric or leatherette .UNDERSTRUCTRE: Understructure is madeup of1 . 2 ± 0 . 1cm .thickhot pressed plywood( moisture resistance & termite proof as per IS: 303) & pinewood of cross section devoid of major knots & surface defects 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose 6 nos. per seat &3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. LEGASSEMBLY :It isa welded assemblymade in Stainless steel( grade SS202 )tube&platewith plastic endcap. (W)1460* (D) 90.5(H) 85.5 cmseat (H) 45.0 cm. Make Godrej or equivalant. 99 Supply, fitting and fixing of 1- Seater Sofa : (S1-L3)-SEAT FOAM :The seat is made of PUfoam with Density28 ±2kg / cu . mtr having anadditional top layer of super softPU foam inDensity32 ±2kg / cu . upholstered with fabricor leatherette .2BACKFOAM :The back ismade of PU foam withDensity28±2kg / cu . mtr with two additionaltop layer of supersoft foam of density32 ± 2kg / cu .mtr ,upholstered with fabric or leatherette .UNDERSTRUCTRE:Understructure is madeup of1 . 2 ± 0 . 1cm .thickhot pressed plywood( moisture resistance & termite proof as per IS: 303) & pinewood of cross section devoid of major knots & surface defects 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose 6 nos. per seat &3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. LEG ASSEMBLY :It isa welded assemblymade in Stainless steel( grade SS202 )tube&platewith plastic endcap. (W)86.0* (D) 90.5(H) 85.5 cm seat (H) 45.0 cm.Make Godrej or equivalant. 100 Supply, fitting and fixingSide Table for Sofa: (ST1-L1) Dimension -(W)60*(D)60*(H)45 Rubber wood under frame. High density plywood top 24 mm thickness. Curved legs with ethnic design Load bearing capacity : 30 Kg“The company should be Greenguard-UL-UL, BIFMA, AIOTA, ISO 9001, ISO 14001, ISO 18001 Certified. List of Approved Makes: Godrej, HermanMiller, Steelcase, Dellform, Vitra” 101 Supply, fitting and fixing of centre table, Dimension -(W)120*(D)60*(H)37.8 Table meterials & size : top: solid veneer mdf table top with 18 mm. Legs: solid rubber wood. Legs:color : cappucino. Company should be Greenguard-UL-UL- UL, BIFMA and GRIHA certified. “The company should be Greenguard-UL-UL, BIFMA, AIOTA, ISO9001, ISO 14001, ISO 18001 Certified. List of Approved Makes: Godrej, HermanMiller, Steelcase, Dellform, Vitra” 102 Providing and placing in position modularCafé Table 4 Seater Size -1500x900mm suitable for cafeteria,public use, comprising fixedtabletop of size 1.50 m X 0.90 m, made of 25–36 mm thick - primary wood . Table shall be mounted on MS or aluminium pedestal base with powder-coated finish and anti-skid base. Table shall be durable, rust-resistant, and suitable for heavy usage in public food courts, airport terminals, lounges, etc. Work includes supply, positioning, installation, cleaning and handing over complete in all respects as per approved layout and direction of Engineer-in-Charge. Approved makes: Godrej Interio, Featherlite, BP Ergo, or equivalent. 103 Supply of Cafeteria chair - (CH1-PTL) The seat and back are made uo injection moulded high impact strenght polypropylene polymer compound with indoor graade UV Resistance. The Powder coated (DFT50+ microns) weled tubular frame is made from 2.22 + 0.03 cm x 0.16+/- 0.0128cm and 3.5+/- 0.03 cmx1.5+/-0.03 cm x 0.16 +/- 0.0128 cm M.S.E.R.W tubThe Shoes are made of high impact strenght polypropylene polymer compond with indoor grad UV Resistance and pressed fitted with tubularfram. SIZE : (W)52.5cm*(D)55.8cm*(H)84.5cm*(seat H) 45.0 cmSeat Size 52.5cm(W)*53.2 cm(D)Back Size 51.6 cm(W)*40.5 cm (H)Company should be Greenguard-UL-UL- UL, BIFMA and GRIHA certified. “The company should be Greenguard-UL-UL, BIFMA, AIOTA, ISO 9001, ISO 14001, ISO 18001 Certified. List of Approved Makes: Godrej, HermanMiller, Steelcase, Dellform, Vitra” The product should have independent Greenguard-UL Gold, SCS- Indoor Air Quality and Greenpro Certificate. The product should be listed in Griha Product Catalogue under the category GRIHA V.3 criteria: 34; GRIHA V.2015 criteria: 31&SVAGRIHA criteria: 14. 104 Supply, fitting and fixing of Visitors chair: (VC4-L14) (Without Revolving) SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressedplywood , upholstered with fabric upholstery covers and moulded Polyurethane foam.SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D)BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns)tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn.BACK SIZE : 46.5 cm. (W) x 60.5cm. (H)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression.ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. .TUBULAR FRAME: The powder coated (DFT 40-60.microns) tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm thick M.S.E.R.W. Tube. Overall Dimensions of ChairSeat Height - 46.5cm.Height - 93.5cm.Width & Depth of Chair as measured from pedestal - Width-61.0 cm and Depth-64.5 cm. “The company should be Greenguard-UL-UL, BIFMA, AIOTA, ISO 9001, ISO 14001, ISO 18001 Certified. List of Approved Makes: Godrej, HermanMiller, Steelcase, Dellform, Vitra” The product should have independent Greenguard-UL , SCS- Indoor Air Quality Certificate. The product should be listed in Griha Product Catalogue under the category GRIHA V.3 criteria: 34; GRIHA V.2015 criteria: 31&SVAGRIHA criteria: 14 105 Supply, fitting and fixing of Visitors chair: (VC3-L10) The seat is made up of 1.4 ± 0.1 cm thick hot - pressed plywood upholstered with fabric and moulded polyurethane foam. SEAT SIZE: 48.0cm (W)x 51.0cm(D).The Back is injection moulded in Glass filled Polypropylene which is upholstered with Mesh fabric.The back consist of fixed lumbar support made of injection moulded Polypropylene having a nominal thickness of 0.4 ±0.02 cm.BACK SIZE: 44.0 cm(W) x 51.5 cm(H).The polyurethane foam for seat is of density = 30 ± 3 kg/m3.The Fixed armrest is made of injection moulded Polypropylene which is connecting seat and backThe mechanism is designed with the following features:• 360° revolving type.• Centre - Tilt.• Tilt with upright lock.The pneumatic height adjustment has a stroke of 9.5 ± 0.5cm.The pedestal is injection moulded Polyamide and fitted with 5 nos.twin wheel castors. The pedestal is 60.0 ±0.5 cm P.C.D.The twin wheel castors are injection moulded in black Polyamide having 5.0± 0.1cm wheel Diameter“The company should be Greenguard-UL-UL, BIFMA, AIOTA, ISO 9001, ISO 14001, ISO 18001 Certified. List of Approved Makes: Godrej, HermanMiller, Steelcase, Dellform, Vitra” 106 Supply, fitting and fixing ofHead Chair: (HC2-L3) The Cushioned seat is made of Injection molded Plastic outer & inner. Plastic Inner is upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression.*Seat SIZE: 47.0 cm. (W) x 48.0 cm. (D) BACK ASSEMBLY: The Cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette. *MID BACK SIZE: 47.7 cm. (W) x 61,1 cm The armrest top is moulded from polyurethane (PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated finish. The armrest height adjustable up to 6.5±0.5cm in 5 steps. The adjustable tilting mechanism is designed with the following features: 360’ revolving type. Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. Tilt tension adjustment can be operated in seating position.5-position Tilt limiter giving option of variable tilt angle to the chair. Seat/back tilting ratio of 1: 2The mechanism housing is made up of HPDC Aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5 cm. Back Frame is connected to the Up/down mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. Pitch-center dia. (75.0 ± 1.0cm. With castors.) The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter.“The company should be Greenguard-UL-UL, BIFMA, AIOTA, ISO 9001, ISO 14001, ISO 18001 Certified. List of Approved Makes: Godrej, HermanMiller, Steelcase, Dellform, Vitra” The product should have independent Greenguard-UL Gold, BIFMA level 2 , SCS- Indoor Air Quality and Greenpro Certificate. The product should be listed in Griha Product Catalogue under the category GRIHA V.3 criteria: 34; GRIHA V.2015 criteria: 31&SVAGRIHA criteria: 14. 107 Supply, Fitting & Fixing of Table, model -Fusion Executive Table Set With Storage SKU: KWT078-M42/M51, Make- Damro or equivalent with the following specifications -Dimensions: W 180 cm x D 80 cm x H 75 cm,Primary Material: Engineered wood,Finish : Melamine,Style :Modern,Warranty : 36 Months Product Feature : Executive writing table design with storage, Made of engineered wood Modern style with attractive modesty panel 50mm thick tabletop with protective PVC edges,Two drawers and two shutters for storage on left and right side,A4 size file storage,Two-tone design,Melamine finish,Knockdown construction,Decorative metal handles.Weight: 106.00 KG 108 Supply, Fitting & Fixing of Table, model name - Haiko Office Table, Make- Nilkamal or equivalent Comprises a engineered wood tabletop, 3 drawers and a shutter compartment, Pre-laminated particle board construction for durability,Lockable shutter compartment and top drawer, Leveler included for adjustment in case of uneven floor surfaces, Melamine finish adds a layer of resistance against wear and tear , Brown shade Dimensions -Width (cm) 150,Depth (cm) 75 Height (cm) 75 109 Supply , Fitting & Fixing of Table, model - Brilliant Linear Work Station, Make Nilkamal or equivalent Made of 15 mm thick pre laminated particle board with melamine finish.It has 3 Drawers (lock and key facility on top drawer) Dual tone colour combination Dimensions-Width (cm) 120,Depth (cm) 60,Height (cm) 75 & Weight (Kg) 42 110 Supply , fitting & fixingof Mobile Pedestal having 3 Drawers Unit having flat metal front and top with Central locking. The Drawer Unit consists of 2Box and 1File Drawers. The Overall size of the Drawer Units is 450mm(W) X 435mm(D) X 646mm(H). Construction & Material of Drawer Unit : Welded Assembled of 0.8 thick CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener & Bottom, 1.2mm thick CRCA Top Stiffener & Bottom stiffener. Drawer Fronts & Metal Front Straight Edge. All Drawers with Double extension precision ball slide shall be provided. For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Locking:10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism. Top Panel : 0.8mm thick Metal Straight Edge Top. Castors : Swiveling non-lockable 4Nos Castors mounted below the body shell. The Total drawer unit is finished with Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10). The product should be complete and as per approved sample and as per the direction of Engineer-In-charge. 111 Providing and placing queue manager post made of high-grade stainless steel (SS-304) with a heavy base and integrated retractable belt barrier system. The post shall be of polished/mirror finish stainless steel tube of minimum 63 mm diameter and 1.2 mm thickness, standing on a round base plate of minimum 320 mm diameter with rubberized anti-slip bottom padding for floor protection and stability. Retractable belt shall be of high-tensile polyester fabric, minimum 2 meters in length and 48–50 mm in width, available in standard colors (blue/red/black) with locking ends and belt clip, suitable for interlocking with adjoining queue posts. Each post shall be self-standing, modular in design, easy to move and interlink, with concealed belt retraction mechanism. Posts to be resistant to corrosion, suitable for high footfall public areas. Of approved make such as Dolphin, Toshi, Euronics, Czar, or equivalent, conforming to IS or relevant international standards. The work includes: – Supplying and positioning queue managers at the specified locations – Alignment in straight/curved layout as per site requirement – Final cleaning and handing over, all complete as per direction of Engineer-in-Charge. 112 Providing and placing stainless steel triple-compartment dustbin with separate internal containers for biodegradable, non-biodegradable, and domestic hazardous/recyclable waste, each of minimum 12-litre capacity (total 36 litres or more), fabricated from high-grade SS 304 stainless steel, with a minimum thickness of 0.8 mm, and constructed with a seamless rectangular or cylindrical body, an integral base, and a partitioned inner structure. The dustbin shall have a satin/matte brushed finish (No. 4) and shall be clearly labelled with laser-etched or high-quality stickered colour-coded markings, in accordance with the Solid Waste Management Rules: Green for biodegradable waste Blue for non-biodegradable/recyclable waste Red for domestic hazardous waste (or as per site-specific classification) Each compartment shall have individual top openings with push-flap lids, hole-cut covers, or hinged lids, and shall be fitted with internal liner-holding rings or removable bins to facilitate easy waste segregation and disposal. The unit shall feature an anti-skid rubber base for enhanced stability and be designed to be corrosion-resistant, durable, and easy to clean, with all edges rounded and burr-free to ensure user safety. The dustbin shall be free-standing or optionally wall-mounted (as specified), and shall be placed in approved locations with proper orientation. The scope of work includes: Supply, delivery, handling Installation (if required) Surface cleaning Handing over in fully usable condition All works shall be carried out as per manufacturer’s specifications and the directions of the Engineer-in-Charge, complete in all respects. 113 Providing and placing stainless steel dustbin of 12-litre capacity, suitable for washroom use, fabricated from high-grade stainless steel SS 304, minimum 0.8 mm thickness, with seamless cylindrical body and integral base, having a brushed satin finish (No. 4). The dustbin shall be free-standing type, with a flat or dome-shaped hinged/lift-off lid and opening slot or push-flap for hygienic hands-free use. Dustbin shall be provided with an internal ring or frame to support disposable garbage liners, and a non-slip rubber base to prevent movement and protect floor surfaces. All corners and edges shall be rounded and polished for safety and ease of cleaning. Work includes supply, placing in approved locations, and handing over in clean, usable condition, complete as per manufacturer’s specifications and as directed by the Engineer-in-Charge. 114 Supply, providing, fitting and fixing the industrial warehouse rack -(M.S heavy dury rack with05 layer and approximate load per layer - 600 kgs- Dimension 1.50 m Length X 0.90 m width & height 3.00 m) in position as per the direction of E-I-C including its transportation to Swaraj Dweep Site and installation at site including cost of labour, minor T&P, transportation charges, GST etc complete
