Tender For P/F Overhead Cantilever/Gantry Direction Board In Sector-74,75,76 And 77 X-Ing, Noida. - Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. All kinds of soil. The contractor has to detect different utilities like sewer line water supply line electric cable telephone cable gas pipe line etc. using utility detecting machine before start of excavation and shall start excavation only after getting permission of Engineer-in-charge.All kinds of soil. 2 Filling available excavated earth (excluding rock) in trenches, plinth sides of foundations etc in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 m and lift upto 1.5 m 3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) 4 Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete 5 Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as perdirection of the Engineer - in - charge.(Note :- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/recoverable separately).All works upto plinth level 6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars 7 Steel work welded in built up sections/ framed work, including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 8 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 9 Retro-Reflective sheeting type-XI with 4mm thick ACM single SideProviding & Fixing of reflective signs with a corrosion resistant 4mm thick with 0.4 to 0.5 mm both side aluminium skin aluminium composite panel face to be fully covered with High intensity prismatic sheeting type XI as per IRC-67:2012 retro reflective sheeting with back frame MS angle of 35x35x5mm Legenda, letters, numerals and borders etc should be as per MoRTH specification No-801.3.7. The Sheeting shall have a pressure- Sensitive adhesive of the aggressive lack type requiring no heat. solvent other preparation for adhesion to a smooth clean surface, in a manner recommended by the sheeting manufacture. The ACM (Aluminium Composite Materials) Shall be fixed on the Back frame MS Angle with riveting. Micro Prismatic type IV Retro reflective sheeting confirming to ASTM D4956-09 Shall be pressure fixed. The Retro reflective, daytime colour and luminance, shrinkage, flexiblitily, liner removal, adhesion, impact resistance, specular glass and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obrained from international/Government Laboratory/institute by the manufacture of the sheeting and in case the certificate is obtained from internation condition, it should also be obtrained from indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively a certificate conforming to ASTM Specification (D4956-09) on artifical accelerated weathering requirements from a reputed laboratory in india can be accepted provisionally, in such a situation, the Employer/Client. if so desires, could seek for a performance guarantee, in such a situation, the Employer/Client. if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012 & Proof of the same Report shall be uploaded which quoting tender. The rate shall include all materials, labour, T&P, Transportation, installation and incidentals all complete as per direction of the Engineer-in-chage. 10 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. 11 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 12 Mobile Hydraulic Crane 35 tonne capacity (173HP) 13 Demolishing R.C.C. work manually / by mechanicalmeans including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer-In-Charge 14 Retro-Reflective Signs (stainless steel Frame and Post with one side sings)Supply & Fixing of reflective signs board (single side) of size 1.50 x 1.20m retro reflective sheeting of HIP grade type-IV, the board shall be fixed on 50mm SS 304 grade ofwith a corrosion resistant 4mm thick ACM sheet of standard make as per MORTH specification. The Board shall be fixed using 2 man post 45x45x60 cm cement concrete foundation. The stainless steel joint welding of SS pipe work shall be band and grinder property inclluding bufting so and to give uniform shinging at welded of SS pipe work shall be band and grinder property. The Retro reflective sheeting shall be tested for a certificate of having the sheeting at welded joints. The Retro reflective, daytime colour and luminance, shrinkage, flexiblitily, liner removal, adhesion, impact resistance, specular glass and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obrained from international/Government Laboratory/institute by the manufacture of the sheeting and in case the certificate is obtained from internation condition, it should also be obtrained from indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively a certificate conforming to ASTM Specification (D4956-09) on artifical accelerated weathering requirements from a reputed laboratory in india can be accepted provisionally, in such a situation, the Employer/Client. if so desires, could seek for a performance guarantee, in such a situation, the Employer/Client. if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012 Legends, letters, Numerals and borders etc. should be as per MoRTH spectification No. 801.3.7 Proof of the same in form of goverment report shall be uploaded white quoting tender.
