|
| 1 | Taking down old unsv roof treatment including PCC padding if any, plastering, removing existing bitumen felt treatment including brushing, cleaning top surface of roof slab, brooming etc incl disposing off debris from MoD land complete all as specified and directed. |
| 2 | Rendering 15 mm thick in cement and sand mortar 1:3 on roof surfaces with mixing of water proofing admixture as per manufacturer\"s instruction including finishing the surface even and fair to receive roof treatment,complete all as specified and as directed.Note:- Supply only Water proofing compound shall not be measured & paid seperately. |
| 3 | Roof treatment :- (a) Apply a coat of bituminous primer conforming to IS - 3384 @ 0.40 Kg/Sqm on prepared surfaces.(b) After drying of primer apply a coat of hot blown 85/25 penetration grade blown bitumen conforming to (IS-702 @ 1.20 Kg/Sqm of surfaces.(c) Provide APP modified polymeric five layered membrane with central core of 100 micron high molecular high density film.Minimum weight of APP modified water proofing membrane shall be 3 Kg per Sqm.Product Name Multi plus manufactured by M/S STP texa Ltd Gurgoan/Hyper Plus Standard Manufactured by IWL India ltd Chennai, Bengal Acquaflux manufactured by Bengal bitumenNew Delhi/Superior plus 310 by STP Lfd and any other product as appproved by E-in-C Br will be used.APP membranne will be laid across the slop from lowest line of slopping roof toward ridge with minimumend lap of 150mm and side lap of 75mm bonded with hot blown. |
| 4 | Sunken Floor treatment :- Providing and laying of water proofing treatmentto sunken portion by applying cement slurry mixed with acrylic based polymer modified cementitious composite compound of make as approved including demolition and filling of sunken floor.(a) First layer of slurry of cement @ 0.488 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @0.253 Kg/Sqm. This layer allowed to air cure for 4 Hours.(b) Second layer of slurry of cement @ 0.242 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.125 Kg/ Sqm his layer allowed to air cure for 4 Hours. Note :- (a). Concrete for sunken slabs shall be mixed with WP compounds asper manufacturer instructions before carrying out water proofing treatment the sunken shall be tested with water for 48 hrs for any leakage/dampeness is seen in ceiling below, then treatment is again carried out to RCC slab and it is again tested (Water proofing compound rate shall not be paid separately). (b). 50mm thick PCC at the bottom of slab and slopeshall be 1:20 toward the corner of outer wall and GI pipe of 50mm dia (Med grade) be inserted at corner projecting outside 20 cm . (c).15 mm plaster mixed with WP Compound shall be provided while concrete is green(d).Only floor area shall be measured for payment purpose.(e). Treatement shall only be done from approved manufacturer & name of manufacturer required to be approved from GE before treatement.(f) Joints of trap/WC/soil pipe shall be properly sealed with sealing compound. |
| 5 | Preparation of new or previously untreated surface of concrete, asbestos cement APP membrane or surface of any description and applying two coats of aluminium paint over roof surfaces over 10cm girth or width, not otherwise described, all as specified and directed. |
| 6 | Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) exc 1.50 Sqm and n.exc 4.00 Sqm each complete all as specified and as directed. |
| 7 | Taking down chowkhats or frameswith shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each complete all as specified and as directed. |
| 8 | Taking down shutters of any description exc 1.00 Sqm and not exc 2.00 Sqm each, complete all as specified and directed |
| 9 | 50mm PCC 1:3:6 type C-0 using 12.5mm graded crushed stone aggregate as in filling of pressed steel frame, parapet,coping including necessary formwork, complete all as specified. |
| 10 | Pressed steel frames for doors with one or more rebates of size 125x60mm including necessary fixing lugs, hinges, lock strike plates complete, providing mild steel 6 mm dia thresh hold bar complete all as specified and as directed. |
| 11 | Pressed steel frames for doors with one or more rebates of size 105x60mm including necessary fixing lugs, hinges, lock strike plates complete including providing mild steel 6 mm dia thresh hold bar complete all as specified and as directed. |
| 12 | Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube, supplying and fixing in opening as per specification and drawing, complete all as specified and directed. |
| 13 | 35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated, complete all as specified. |
| 14 | Glazed and skeleton shutters 30 mm thick second class hard wood, opened rebated and prepared to receive wire mesh etc, edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for sucuring witre mesh etc. Size of members of shutters as specified in SSR Part-I, Sec-8, clause 8.24(a). |
| 15 | Pre laminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screw to timber frame in repairs as cupboard shelve and shutter, 19 mm thick in repairs, complete all as specified and directed. |
| 16 | External teak wood lipping, 6mm thick fixed with nails for 18/19mm thick board, complete all as specified and directed. |
| 17 | Factory made solid core PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet, \"C\" channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) and directed. |
| 18 | 300mm Mild steel ordinary rat tail rod pattern springs including roller and roller plate fixed, complete all as specified. |
| 19 | Powder coated anodised aluminum frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified. |
| 20 | Powder coated aluminium Anodised aluminium door shutter with top rail,bottom rail, middle railand style of size 85mmx 44mm x 1.6 mm thick with 200mm size aluminium handle on both side of shutter aliminium tower bolt 150 mm long 2 Nos per leaf including 5.5 mm thick selected quality sheet glass , joining cleats, glazing clips, rubber neoprene packing, aluminium beading and screwed hydraulic door closer for each leaf , mortic lock 4 levers with 2 Nos key , 3Nos butt hinges of stainless steel for each shutter complete all as specified and as directed. |
| 21 | Powder coated anodised aluminium window (including glazed or gauged skeleton shutter ) and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 No.) suitable handle (1 No.) including 5.5 mm thick selected quality sheet glass in glazed shutter orsteel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in gauzed shutter respectively, complete all as specified. |
| 22 | Door closer hydraulically regulated, aluminium extruded section body designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and as directed. |
| 23 | Anodised Aluminium grill (anodised transparent or dyed toi required shade according to ISD: 1868 with minimum anodic of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with CP brass/stainless screws@ 2090 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium strandard section around the opening complete all as specified and directed |
| 24 | 5.5 mm thick tinted sheet glass, selectedquality and glazing with aluminium beads and rubber packing in square not exceeding 0.5 square metre in each pane fixed in repairs, complete all as specified and as directed |
| 25 | 5.5 mm thick tinted sheet glass, selectedquality and glazing with aluminium beads and rubber packing in squareexceeding 0.5 square metre in each pane fixed in repairs, complete all as specified and as directed |
| 26 | Galvanized mild steel wire-cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 27 | Butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified and as directed. |
| 28 | 150 mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and as directed. |
| 29 | 200 mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and as directed. |
| 30 | 300mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified and as directed. |
| 31 | Steel windows/ventilator (Box type) factory made with double shutter with or without devetailed bar ( glass & glazed shutter) of size 79mmx39mm,16 gauge rectangular tubular frame withside hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts in each shutter 100mm long with & including 8mm square bar grills, complete all as specified & as shown on drg No. CEUZ/TD/1269/2008 Sh No 1/1 to 1/3 .Note:-(a) Fixed type glass panes shutter if any provided in above same window shall be measured and paid separately & area of these fixed shutter shall be deducted from total area of box type window for payment purpose. (b) Sheet glass/ wire cloth shall be measured & paid seperately under respective item |
| 32 | Description all as per Item No.31 above, but only fixed glass pane shutter without glazing bars. |
| 33 | Galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed. |
| 34 | Galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples fixed in repairs, complete all as specified and directed. |
| 35 | Hacking out old broken glass (any thickness, size, quality or description) from metal frames/Aluminium framesincluding punching or drilling out old glazing pins/spring clips complete all as specified and as directed. |
| 36 | 3 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and as directed. |
| 37 | Figured glass pin headed type, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified. |
| 38 | Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed at bottom rail of door of overall length of cover plate 150mm , all as specified and directed. |
| 39 | Preparation new steel and iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer, complete all as specified and as directed. |
| 40 | Preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paintof Ist quality over a coat of pink primer, complete, all as specified. |
| 41 | Curtain rail ,20 mm dia Stainless steel ,chromium platedfixed with CP braket, incl taking down of old curtain rods, complete all as specified. |
| 42 | Dismantling offloor hearth or wall tilling incl cement mortar bedding and removing unsv tiles and rubbish off the premises, completeall as specified and directed. |
| 43 | Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level ) complete all as specified and as directed. |
| 44 | 75mm thick PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection laid in bays with mastic filling in joints complete including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified. |
| 45 | Bituminous mastic filling, with 85/25 or 95/10 grade bitumen and coarse sand mixtyure 1:3 by weight (comprising of one part of heated bitumen and 3 parts of sand) 8cmx8cm filling the joints with mastic at the junction of bays of plinth protection to vertical surfaces |
| 46 | 25 mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in sub base floor finishing surface even and fair, complete all as specified. |
| 47 | Non skid coloured ceramic tiles 7 to 8 mm thick(square / rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles over and including 15mm thick screed bed in CM (1:4), complete all as specified and directed. |
| 48 | Description all as per item No-47 above but in vertical surfaces such as in skirting, dado etc.fixed over and including 10mm thick plaster in CM (1:4), complete all as specified and directed. |
| 49 | Vitrified ceramic tiles light shade 10 mm thick (square/rectangular) area of each tile not exceeding 0.36sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:4), complete all as specified and directed. |
| 50 | Description all as per item No-49 above but in vertical surfaces such as in skirting, dado etc.fixed over and including 10mm thick plaster in CM (1:4), complete all as specified and directed. |
| 51 | Glazed ceramic coloured tiles (300 x 250mm/ 450 x 300mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10mm thick back coat layer plaster in cement mortar 1:4, complete all as specified and directed. |
| 52 | 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms, in counter WHB and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite laid over & including 20mm thick screed bed in CM 1:4, complete all as specified |
| 53 | Taking down cement plaster of any description including raking outjoints, hacking for key, scrubbing down with water etcall as specified and as directed. |
| 54 | 15mm thick cement plaster rendering in CM 1:4 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified. |
| 55 | 10mm thick cement plaster rendering in CM 1:6 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified. |
| 56 | Rendering 5 mm thick in cement and sand mortar 1:3 on concrete surfaces of ceiling including finishing the surface even and smooth without using extra cement complete all as specified |
| 57 | Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed. |
| 58 | Brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified. |
| 59 | Description all as per item No 58above but except bricks. |
| 60 | M&L for walling of random rubble uncoursed, well bonded, bedded and solidly hearted built in CM 1:4 complete all as specified and directed. |
| 61 | M&L for walling of random rubble uncoursed, well bonded, bedded and solidly hearted built in CM 1:4 but except stones all as specified and directed. |
| 62 | Raised pointing to random rubble, uncoursed or brought upto course masonry in CM 1:4 complete all as specified. |
| 63 | Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 40mm to face stones (lime and sand stone) and dressing of face beds and joints, complete all as specified. |
| 64 | Preparation of newly plastered and unplastered surfaces of walls andapplying two coats of oil bound distemper over a coat of chalk whitening primer complete all as specified and as directed. |
| 65 | Preparation of newly plastered and unplastered surfaces of walls andapplying two coats of cement based paint over a coat of chalk whitening primer complete all as specified and as directed. |
| 66 | Preparation of newly plastered surfaces of walls andapplying two coats of oil bound distempert over a coat of chalk whitening primer complete all as specified and as directed. |
| 67 | Repair to balcony/Facia/Roof projections and soffit of chajjas etc by taking down old rendering and hacking clearly the edges and corners smooth rounded for new plastered area exceeding 30sqm in width or girth & providing 15 to 20mm thick plastering to match with the existing thickness in CM 1:3andincluding formwork up to height 7 mtr above ground level of bldg including two coat of Apex/cement based paint over one coat of primer complete all as specified. |
| 68 | Rotational moulded polyethylene water storage tanks 1000 Ltrs Capacity, white in colour(cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified and directed. |
| 69 | Rotational moulded polyethylene water storage tanks 500 Ltrs Capacity, white in colour(cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified and directed. |
| 70 | Supply only ball valve high pressure PTMT with epoxy coated aluminium rod& high density plastic ball 20mm dia bore. |
| 71 | 15 mm dia bore gun metal globe or gate valve with iron wheel head screwed both end for iron pipe fixed in repairscomplete all as specified and directed. Maker- Hindware, Parryware, Cera, Prayag, Jaquar |
| 72 | 20 mm dia bore gun metal globe or gate valve with iron wheel head screwed both end for iron pipe fixed in repairscomplete all as specified and directed. Maker- Hindware, Parryware, Cera, Prayag, Jaquar |
| 73 | Taking down eaves gutters and rain water pipe , soil and waste pipe (any size or pattern), includding all fittings, heads , shoes bends , swan-necks etc . complete all as specified. |
| 74 | 110mm bore PVC SWR Type-B pipes(pressure not less than 6 kg /cm2) single socket in any length with rubber joints laid in floors/trenches etc all as specified and directed. |
| 75 | 75mm bore PVC SWR Type-B pipes(pressure not less than 6 kg /cm2) single socket in any length with rubber joints laid in floors/trenches etc all as specified and directed. |
| 76 | PVC SWR bends any radius 110 mm bore with oval access door all as specified and as directed. |
| 77 | PVC SWR bends any radius 75 mm bore with oval access door all as specified and as directed. |
| 78 | PVC SWR 110mm dia Type-B ( pressure not less than 6 kg /cm2) pipes in any length fixed to walls with PVC/MS holder or clamps and conforming to IS-1729 complete all as specified and directed. |
| 79 | PVC SWR 75mm dia Type-B ( pressure not less than 6 kg /cm2) pipes in any length fixed to walls with PVC/MS holder or clamps and conforming to IS-1729 complete all as specified and directed. |
| 80 | PVC (SWR)110 mmjunction single, (Single T) equal or unequal ordinary or inverted with spigot or socket branch with oval access door all as specified and as directed. |
| 81 | PVC (SWR) 75 mmjunction single, (Double Y) equal or unequal ordinary or inverted with spigot or socket branch with oval access door all as specified and as directed. |
| 82 | PVC cowls 110mm fixed in repairs complete all as specified and directed. |
| 83 | PVC cowls 75mm complete all as specified and directed. |
| 84 | PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 85 | Taking up or down 15mm dia steel water tubing and connections all as specified |
| 86 | Taking up or down 20mm dia steel water tubing and connections all as specified |
| 87 | GI water tubes 15mm bore dia medium grade galvanised (ISI Marked) with all fittings and fixed complete to walls and ceiling or laid in floor including taking down old pipe all as specified and directed. |
| 88 | GI water tubes 20mm bore dia medium grade galvanised (ISI Marked) with all fittings and fixed complete to walls and ceiling or laid in floor including taking down old pipe all as specified and directed. |
| 89 | CP angle valve/concealed stop cock of cast copper alloy (ISI Marked) chromium plated fancy type scrwed down high pressure with capstain head screwed both ends for iron pipe 15mm bore incl add if fixed in repairs complete all as specified and directed. |
| 90 | PVC valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete, fixed in repairs complete all as specified and as directed. |
| 91 | Vitreous china squatting pan \"Orissa Pattern\" size 580 x 440 mmin white colour with integral foot rest incl lime mortor, \"S\" trap fixed in repairs complete all as specified and directed.Cat Part No-20042 (ORISSA PAN (ECO)) of Hindware or equivalent cat part of make specified in list make as approved by GE. |
| 92 | Vitreous China floor mounted Single piece wash down water closet pan (pedestal pattern)(size 370mm x 670mm x 720mm) with UF soft close slim seat cover,Hinges, Dual Flush cistern fitting, fixing accessories and set with \"S\" trap size 300mm including connection to drain (or outgoing pipe), antisyphonage pipe, etc.. complete fixed in repairs complete all as specified and directed.Make-Jaquar (Lyric) Cat Part No. LYS-WHT-38851S300UFSMNor its equivalent cat part of make specified in list make, as approved by GE. |
| 93 | Vitreous china wash down water closet pan pedestal pattern size 570mm x 460mm x 380mmin white colour excluding seat cover, flushing cistern and flush pipe fixed in repairs complete all as specified and directed.Cat Part No-20011 of Hindware or its equivalent cat part of make specified in list make, as approved by GE. |
| 94 | Plastic water closet seat cover white closed pattern with flat bottom and cover including chromium plated hinges device fixed in reapir, complete all as specified and as directed. |
| 95 | Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.2 meter long flexible spirochrome flex tube and ABS wall hook including making connections and fixed in repair in position complete in all respect as specified.Make-Jaquar Cat part no. ALD-573 or its equivalent cat part of make specified in list make, as approved by GE. |
| 96 | Toilet paper holder with flap recessed type stainless steel Complete all as specified and directed.Make-Jaquar cat part no. AQN-7753 or its equivalent cat part of make specified in list make, as approved by GE. |
| 97 | Vitreous China urinal with CP spreader Chrome finish hole and fixing accessories Half stall type (back or corner wall type)(size 355mm x 340mm x535mm) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; including PVC Connection,waste pipe and coupling. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) fixed in repairs complete all as specified and as directed by Engineer-in-Charge. Make- Jaquar Cat part no. URS-WHT-13261H or its equivalent cat part of make specified in list make, as approved by GE. |
| 98 | Vitreous china wash basin, white, flat back, size 550x400mm including CP mixer for mixing hot and cold water for pipe of bore 15mm, waste fitting chromium plated brass, chromium plated steel chain and rubber plug, porcelain stopper, a pair of CI brackets and waste pipe etc., fixed in repairs complete all as specified and as directed.Cat Part No. 10036 of Hindware (Model-Windsor) or equivalent cat part of make as specified in the list of makes as approved by GE. |
| 99 | PVC connection 15mm size with PTMT nuts on both ends of length 600mm fixed in repairscomplete all as specified and as directed. |
| 100 | Waste pipe for WHB/Urinal for 32/40mm fixed in repairs, complete all as specified and as directed. |
| 101 | Brass chromium plated shower rose 125mm sizewith or without swivel joints, with arm any size, including fixing to steel pipe or union fixed in repairs complete all as specified and directed |
| 102 | Bib taps 15mm dia, fancy type chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe for brass ferrule, for bore dia of pipe 15mm fixed in repairs, complete all as specified and as directed . |
| 103 | Bib tap (long body)15 mm standard of PTMT any colour high pressure screwed for iron pipe and fixedin repairs complete all as specified. |
| 104 | Chromium plated fancy type quarter turn Pillar cock screwed down high pressure with crutch or butterfly handle screwed both end 15 mm bore dia fixed in repairs all as specified. Make-Jaquar Cat part no. FON-40011 of Jaquar or its equivalent cat part of make specified in list make, as approved by GE. |
| 105 | 15mm bore brass CP wall mixer with provision for overhead shower arrangement with 115mm long bend pipe on upper side for mixing hot and cold water supply screwed down with connecting legs CP extension nipple & wall flange connector for hand shower arrangement with connecting Legs, wall Flanges & wall bracket for hand shower for mixing hot or cold water, screwed for iron pipe and fixed in repairs, complete all as specified and directed.Make-SOL-6273UPR of Jaquar or its equivalent cat part of make specified in list make, as approved by GE. |
| 106 | CP Brass swan neck Pillar cock with left/right hand operating knob with 450mm long braided hose screwed downfor iron pipe 15mm dia bore fancy type fixed in repair complete all as specified and directed. Cat part no. CON-123BKN/127BKN of Jaquar or its equivalent cat part of make specified in list make, as approved by GE. |
| 107 | CP grating with or without hole100 mm dia fixed in repairs all as specified and as directed. |
| 108 | Stainless steel Soap dish, any type, fixed with plugs chromium plated brass screws fixed in repairs complete all as specified and as directed.Cat part No-AQN-7733 of Jaquar or its equivalent cat part of make specified in list make, as approved by GE. |
| 109 | 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick commercial quality ply-wood and fixed to wooden plugs with chromium plated brass screws and cup washers fixed in repairs, completeall as specified and as directed. Make: Saint Gobain, Modiguard, Prayag |
| 110 | Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw for cooler stands and water tank stand including bending and welding angles, as necessary , gusset plates, riveting etc n exc 10 Kg each brackets, conforming to Fe.290. Gde E-165 (Brackets over 10 Kg each to be measured under \"Structural Steel\") Complete all as specified and directed . Note-Quoted rate shall also include cost of fabrication and fixing at site. |
| 111 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering, all as specified. |
| 112 | Dismantling of asbestos, cement (corrugated, semicorrugated, etc.) sheets in roof coverings , complelet all as specified and directed. |
| 113 | Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed. |
| 114 | Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, valley gutter, ridge & similar works fixed with self tapping screws complete all as specified. |
| 115 | Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified and as directed. |
| 116 | Structural steel work as in roof trusses (framed), trussed purlins, crane gantries, rails and fastening and heavy brackets (Beam, tee, angle, channel or hollow steel section) including distance pieces, cleats etc confirming to Fe-290-W (Gde-E-165) quality B complete all as specified. |
| 117 | Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness, including cover fillets, all as specified. |
| 118 | Providing & fixing of 4mm thick designer ceiling board fixed with screw as per manufactures instructions, laid on hot dipped galvanized iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick galvanized steel sheet & of size 24x32x300mm and spaced at 12mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of Gl wire 4mm dia to be fixed by approved rowl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall flush fitting of 1200 long cross tee with (double stitching) to be inter locked between main runners at 600mm centre to from 1200x600mm modules cross tee longer than 600mm modules to be formed by fitting 600mm long cross tee, tee perimeter wall angle shall be of 0.45mm thick galvanized steel of size 19x19mm and 300mm long of white colour all as per instruction complete all as specified & directed. |
| 119 | Restraining,resecuring including making good of loose/disturbed GI snap grid ceiling frame work incl carefully taking down ceiling board and refixing/fixing new onein position if required, complete all as specified and directed.Note:-Supply only ceiling board required for replacement if any shall be measured & paid under relevant item. |
| 120 | Supply only 4mm thick designer ceiling board( excluding framework) all as specified. |
| 121 | S&F in replacement of Kitchen cabinets of PVC Solid board(wooden texture) size 900mmx750mmx600mm, including partitions, shelves and drawers with brass sliding rails,channels,door handles, door catchers, overall cabinet internally and externally madewith both side PVC laminated termite proof board, 18/19 mm thick, ISI marked including PVC kitchen/cup board frame of size 18mmx63mm made out of 18mm thick PVC pre-laminated ply coloured and frame shall be fixed with 50mm long steel screw inside using drilling machine and plastic fasteners, having following specifications: (i)Outer frame made six 50mmx47mm with same board.(ii)Shutters both side PVC laminated termite proof board, 18/19 mm thick having stainless steel soft closing concealed hinges with one No brass handle of 75mm including brass door catcher of not less than 50mm size in each shutter.(iii) Drawers made of both side PVC laminated termite proof board, 18/19 mm thick including brass handles of front and two sliding rails at sides in each drawer.(iv) All cabinets, drawers, frames, partitions and boards shall be fixed at site with brass machine screws and PVC plugs of suitable sizes. Note:(a) Only front face dimensions at site (Length and Height), shall be measured and entered in MB irrespective of Nos of partitions or drawers. Cost of all partitions as required at site shall also be deemed to have included in quoted rates and nothing extra is admissible on this account. (b) Different No of partitions and drawers may be as per site requirement with out any extra cost.(c) All labours and materials cost shall be deemed included in quoted rate. |
| 122 | 5.5 mm thick Frameless wall mounted decorative Looking mirror with bevelled edge made out of premium glass, provide a clear and normal reflection incl installation with full round brass holder and top cap of heavy duty stainless steel with minimum of 4 pieces in one mirror. Pattern and size of Mirror will be decided as per site requirement by AGE,all as specified and as directed. |
| 123 | Dazzle Kitchen Modular BWR Plywood Vanity Washbasin Cabinet (White) size 450mm x 760mm x 830mm, made out of PVC laminated BWR plywood drawers(2 or 3 nos) on right side with one nos handle at front and two nos sliding channel at both end of drawer. A cabinet should be provided on left side having two doors of PVC membraned plywood internally partitioned vertically into two parts and door shutter must be fiitted with auto hinges. Provision of wash out pipe for passage of waste water will be given and connected with existing floor trap/grating and CP Fency type tall basin Mixer of Parryware cat part no. G3946A1 or its equivalent cat part of make specified in list make, as approved by GE. screwed down for 15mm bore iron pipe fixed all as specified and as directed. |
| 124 | Taking down aluminium door shutter of any size/any description and making functional by way of repaier/replacement of floor spring, hinges, mortice lock, rubber packing 5.5. mm thick frosted glass of required size etc as required and refixing in position of same opening (all required iterms will be included in quoted rates) complete all as specified and directed. |
| 125 | Supply only liquid water proofing admixture. |
| 126 | Brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4, complete all as specified. |
| 127 | Rendering 15mm thick cement plaster with cement mortar(1:6) on fair faces of brick work or concrete surfacesand finished even and smooth without using extra cement all as specified and directed. |
| 128 | GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste in repairs in patches n exc 5 sq. m each, including taking down old and jointing new to old as required all as spd and directed. |
| 129 | Applying 3mm thick wall care putty on new plastered surfaces of wall complete all as specified and as directed. |
| 130 | Preparation of New plastered and unplastered surfaces/putty surface of walls and applying two coats of oil bound distemper over priming plastered and other surfaces with alkali resistant priming paint all as specified and as directed. |
| 131 | Erashing, rubbing down and stopping of distempered and painted surfaces of wall and applying 3 mm thick wall care putty complete all as specified and directed. |
| 132 | Preparation of new putty surfaces of walls and applying two coats of oil bound distemper over one coat of primer all as specified and directed. |
| 133 | Preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed. |
| 134 | Applying 2mm thick wall care putty over newly plastered / old plastered surfaces of wall, complete all as specified and as directed. |
| 135 | Preparation of oldplastered and unplastered surfaces of walls and applying one coat of oil bound distemper white/tinted including filling small depressions by putty , washing, rubbing, stopping brooming down with steel wire brushing all as specified and directed. |
| 136 | Preparation of old plastered & unplastered surfaces of walls and applying two coats of oil bound distemper (white/tinted) complete all as specified and as directed. |
| 137 | Preparation of old painted surfaces by washing, rubbing down and stopping of distempered or painted walls and applying one coat of cement base paint white or tined, complete all as specified and as directed. |
| 138 | Preparation of old plastered surfaces of ceiling etc. and applying two coats of white wash, complete all as specified. |
| 139 | Preparation of old decorated surfaces of wall and applying one coat of oil bound distemper on walls all as specified and directed. |
| 140 | M&L for preparation of new plastered & unplastered surfaces of walls by applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces complete all as specified and directed. |
| 141 | Complete removal of existing treatment and preparation of old plastered surfaces of walls & applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on wall surface, complete all as specified and directed.Note:-(i) The work shall be carried out in different shade and the same shall be got approved from Engineer-in-charge/GE/(ii) The work shall be carried out upto 4th storey of bldgs and no extra payment shall be admissible for necessary form work & scaffolding required for the same. |
| 142 | Preparation of Oldplastered and unplastered surfaces of walls,washing, rubbing, stopping,brooming down old distempered/painted surface with steel wire brushesincluding filling small depressions by putty and applying one coat of Interior plasticEmulsion paint 1st quality (White/Tinted) incl priming of surface all as specified and directed. Make: Asian Paint, Nerolac, Berger Paint |
| 143 | Preparation of Oldplastered and unplastered surfaces of walls,washing, rubbing, stopping,brooming down old distempered/painted surface with steel wire brushesincluding filling small depressions by putty and applying two coat of Interior plasticEmulsion paint 1st quality (White/Tinted) incl priming of surface all as specified and directed. Make: Asian Paint, Nerolac, Berger Paint |
| 144 | Preparation on old plastered surfaces of walls and applyingtwo coat of white wash including complete removal of existing treatmentcomplete all as concerned and directed. |
| 145 | Preparation ofold steel surfaces of any descriptionexc 10 cm width or girth, and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 146 | Preparation of old wood or wood basedsurfaces of any description not otherwise described over 10 cm in width or girth, and appying one coat of synthetic enamel paint complete all as specified and as directed. |
