Spl Repairs To Bldg No P32 Of Med Regt Under Ge N Akhnoor; 1 Taking down old unsv roof treatment including PCC padding if any, plastering, removing existing bitumen felt treatment including brushing, cleaning top surface of roof slab, brooming etc complete all as specified and directed. 2 Rendering 10mm thick cement plaster with cement mortar (1:4) on fair finishes of brick work or concretesurface of roof slab all as specified. 3 Water proofing treatment to RCC roof slab including parapet as under :- (a) Ist Course: Apply a coat of bituminous primer conforming to IS-3384@ 0.40 Kg /Sqm on prepared surface of plaster and after drying of primer, apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm on plastered surfaces. (b) 2nd Course :APP (Atactic Polypropylene) modified polymeric membrane, 5 layered,3 mm thick weight not less than 3.0 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 150 mm end overlap, membrane has to be laid with LPG torch and overlap sealed and finished neat, all joints.(c) 3rd Course : Apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm over membrane and dusted with dry sand @ 0.50 to 1 Kg/sqm. (i) On Non-accesible roof : After providing (a) to (c) provide aluminium paint as per manufacturer instructions.(ii) Coved fillet in PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) of required radius 75mm shall be provided at the junction of roof and vertical surface such as parapet wall/mumty around opening and treatment mentioned above shall be applied followed by a cement plaster 20mm thick in cement mortar(1:6).Note :(i) Roof treatment work shall be carried out through approved manufacturers only or through their authorised personal only. 4 Sunken Floor treatment :-Providing and laying of water proofing treatment to sunken portion including vertical portion by applying cement slurry mixed with acrylic based polymer modified cementitious composite compound of make as specified and approved including demolition and filling of sunken floor with & including PCC 1:5:10 type E-2 (using 40mm brick aggregate).(a) First layer of slurry of cement @0.488 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.253 Kg/Sqm. This layer allowed to air cure for 4 Hours.(b) Second layer of slurry of cement @0.242 kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.125 Kg/Sqm. This layer allowed to air cure for 4 Hours.(c) 15mm thick plaster in CM 1:3 mixed with WP compound to be provided while concrete is still green.(d) Joint of/Trap/WC/Soil pipes shall be properly sealed with sealing compound.Note:(a) Concrete for sunken slabs shall be mixed with WP compounds as per manufacturers instructions. Before carrying out water proofing treatment the sunken slab shall be tested with water for 48 hours for any leakage /dampness is seen in ceiling below, then treatment is again carried out to RCC slab and it is again tested before passing for next stage. (The rate quoted includes water proofing compound as per manufacturers instructions).(b) Please note that only floor area shall be measured for payment purpose. 5 Dismantling of AC/CGI/Galvalume sheets corrugated or semi-corrugated in roof covering including ridges, hips, valleys and flashings etc complete all as specified and as directed. 6 Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed. 7 Structural steel work as in roof trusses (framed), trussed purlins, crane gantries, rails and fastening and heavy brackets (Beam, tee, angle, channel or hollow steel section) including distance pieces, cleats etc confirming to Fe-410-W (Gde-E-250) quality B complete all as specified and directed. 8 Pre-painted galvalume aluminum zinc coating GI based corrugated sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws complete all as specified and directed. 9 -Ditto- all as per item No 8 here-in-before but plain sheets. 10 Dismantling wall and ceiling boards, fibre pulp insulation etc or insulation boards/ slabs / blankets, any thickness, including cover fillets, complete all as specified and directed. 11 4mm thickPre-laminated designer false ceiling board over GI snap grid frame work (Grid size 600x600mm) with powder coated GI angle of size 25x25x3mm, main runner Tof size 25x40x3mm , secondary runner T of size 25x30x3mm suspended with 3mm GI wire @ 1200mm c/ccomplete all as specified and directed. 12 Demolition of brickwork or stone boulder masonarybuilt in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed. 13 Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cementsand mortar 1:6 complete all as specified and as directed. 14 Brick work with sub class B brick straight or curved on plan to any radius in half brick thick built in CM 1:4 complete all as specified and directed. 15 Taking down cement plaster from brick or stone walls incl racking out joints hacking for key, scrubbing down with water etc all as specified and directed. 16 Rendering 15mm thick cement plaster with cement mortar(1:4) on fair faces of brick work or concrete surfacesand finished the surface even and smooth without using extra cement, complete all as specified. 17 Rendering 10 mm thick cement plaster with cement mortar(1:6) on other than fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified 18 Rendering 5mm thick cement plaster with cement mortar(1:3) on concrete surface as in ceiling finished the surface even and smooth without using extra cement, complete all as specified. 19 Supply only integral water proofing admixure 20 Repair to Roof projection/Chajjas/ Facia including taking down old worn out rendering and Rendering 15mm thick on external wall surfaces (ht upto 7.0 m from ground level) in cement mortar 1:4 finished fair and even without using extra cement using GI wire netting 0.90mm dia and 12mm mesh lathing, complete all as specified.Note : (i)Rate quoted are deemed to incl double scaffolding and wire netting reqd in the work. 21 Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over one coat of primer complete all as specified and as directed. 22 Preparation of newly plastered surfaces of walland applying two coats of cement base paint over a coat of alkali resistance primer complete all as specified and directed. 23 Preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified. 24 Removal of old treatment of wall by washing rubbing down and stopping of destempered surfaces complete all as specified and directed. 25 Applying wall care putty of approved make not less than 1-2mm thick on walls as per manufacturar instructions with and including rubbing by means of sand / abrasive paper to have smooth finishing to receive primer / paint, complete all as specified. 26 Preparation of newly plastered surfaces of walls andapplying two coats of oil bound distemper over a coat of chalk whitening primer complete all as specified and as directed. 27 Preparation of old decorated surfaces including brooming down or steel wire brushing, scraping down smoke soot, moulds,moss and efforescent salts and removing oil and greasy spots and applying one coat of cement base paint on walls all as specifiedand directed. 28 Preparation of old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed. 29 S&F in repair 25 mm dia stainless curtain roadcomplete with stainless bracket and side caps fixed in positionby drilling holes in walland fixed the bracket with rawl plug and SS screw all as specified and as directed. 30 Demolition of stone slaband tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc. complete all as specified and directed 31 20-25 mm thick machine cut kota stone slab as in flooring, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over with mirror cut polishing 100mm wide marble patti/border all around and including 15mm thick screed bed in cement and sand mortar 1:4 complete all as specified and as directed.Note:-(Size of Kota Stone slab shall be 52 cm x 52 cm). 32 Description all as per item No 31 above but in skirting/dado incl 10mm thick rendering CM 1:4 complete all as specified and directed. 33 Granite (of any type) work 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and like including pointing in white cement (1:2) using marble dust with admixure of pigment to match with shade of granite including 15mm thick screed of CM 1:4 after applying cement slurry@3 kg/sqm of cement per sqm, complete all as specified.(Note : A hole shall be drilled in the Granite after fixing for gas pipe all as directed). 34 Demolition of cement concrete(unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or aboveground level) complete all as specified and as directed. 35 Demolition of Cement Concrete (reinforced) of any description and in any position not otherwise specifically provided for including removing the rubbish off the premishesall as specified and as directed. 36 Reinforced cement concrete nominal mix Type B-0 1:2:4 (12.5 mm graded crushed stone aggregate) forcooking platform , slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. 37 Mild steel TMT bars 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed. 38 Providing cement concrete type C-2, 1:3:6 ( using 40mm graded stone aggregate),75mm thickas in plinth protection laid in bays not exceeding 2 Sqm each and finishing even and fair ontop without using extra cement with 6mm wide joints throughout the thickness of plinth protection in concrete bays and in between the walling and plinth protection, filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand ( all by weight). 39 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 40 Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floors etc.set and jointed in neat cement slurry and pointed in coloured cement to match including 15 mm thick screed bed in cement and sand mortar 1:6,complete all as specified and directed. 41 Description All as per item No 40 here-in-before, but on dado/skirting etc incl 10mm rendering in CM 1:4 complete all as specified and directed. 42 40mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in sub base/ floor finishing surface even and fair, complete all as specified. 43 Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular), area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, as in floors, set and jointed in neat cement slurry and pointed in colouredcement laid over & including 15mm thickscreed bed or bedding layer in cement mortar 1:6,complete all as specified and directed. 44 Glazed ceramic coloured tiles (350 x 250mm/ 450 x 350mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10mm thick back coat layer plaster in cement mortar 1:4, complete all as specified and directed. 45 Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) exc 1.50 m and n.exc 4.00 Sqm each complete all as specified and as directed. 46 Taking down chowkhats or frameswith shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each complete all as specified and as directed. 47 Taking down shutter of any description area exc 1 sqm but not exc 2.0 sqm each, complete all as specified and directed. 48 Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. 49 Powder coated aluminium anodised door shutters(minimum thickness of powder coating 50 micron), aluminium section weighing 0.55 kg/m includingnecessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed. 50 Powder coated anodised aluminium window / ventilator( glazed / gauged skeleton shutter ), (minimum thickness of powder coating 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m includingnecessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinges type B-21 100mm long (2 No. ) suitable handle (1 No.) complete all as specified and as directed. 51 Aluminium powder coated Anodised aluminium window ( including glazed and skelton shutter ) and ventilator shutters, fixed type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws etc complete all as specified. 52 Anodised Aluminium grill powder coating (anodised transparent or dyiong to required shade according to IS-1868 with minimum anodised coating of grade AC15) of approved design patteern with approved standerd section and fixed to existing window framework CP Brass/stainless steel scrw@200mm c/c incl cutting grill to proper opening size for fixing and operation of handle etc complete all as specified. 53 Mild steel framed workas in door or gate of angle or other section with gusset plate, rail braces complete drilled for fixing of steel sheeting or other covering . door etc to be prepared for hanging of sliding with grills, grating etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, conforming to Fe-410-W(Gde-E-250) quality-B, complete all as specified and directed . 54 Factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC C channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading andjointed together with solvent cement supply & fixing in the frame at site, complete all as specified and as directed. 55 Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube, supplying and fixing in opening as per specification and drawing, complete all as specified and directed. 56 Pressed steel frames of sizes 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia threshold bar and filling hollow of frame,all as specified and directed. 57 Pressed steel frames of sizes 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia threshold bar and filling hollow of frame,all as specified and directed. 58 M&L For PCC 1:2:4 type B-0 (Using 12.5 mm graded crushed stone aggregate) as in filling of pressed steel frame.and including 50 mm parapet coping all as specified and directed. 59 35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated, complete all as specified. 60 35 mm thick, 2nd class Soft wood , glazed & skeleton factory made shutters, open rebated & prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.20(a) complete all as specified. 61 100 mmbutt hinges, medium weight cold rolled mild steel, complete all asspecified. 62 Aluminium handles cast type anodised of size 150mm long ISI marked complete all as specified and as directed. 63 Aluminium anodised barrel tower bolt 200mm extruded section ISI marked complete all as speicified. 64 Mild steel springs for doors, 300 mm, ordinary rat tail rod pattern including roller and roller plate complete all as specified. 65 Aluminiumanodised sliding door bolts with hasp and stapple extruded sectionor cast aluminium alloy with length of bolt as 300 mm including fixing bolts complete all as specified. 66 03mm thick figured (frosted) glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and as directed. 67 3mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane complete all as specified. 68 Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed. 69 Floor door stopper 140mm overall length of cover plate of aluminium alloy body and tongue,anodised,with hard drawn steel spring,fixed in bottom body of door complete all as specified and as directed. 70 Preparation new steel and iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer, complete all as specified and as directed. 71 Preparation of new untreated wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and painting with two coats of synthetic enamel paint over a coat of pink primer all as specified and directed. 72 Preparation of old steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed. 73 Preparation of old wood or wood basedsurfaces of any description not otherwise described over 10 cm in width or girth, and appying one coat of synthetic enamel paint complete all as specified and as directed. 74 Chequered cement concrete tiles 30cmx30cmx25mm thick laid & jointed with grey cement and pointed with cement slurry and pigment to match shed of tiles, laid over and including 15mm thick screed bed in CM 1:6,,complete all as specified and directed. 75 Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundations filling and mass concrete, complete all as specified. 76 Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) 3 layered hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified. 77 Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed. 78 Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed. 79 Mild steel galvanized steel tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete ofbore15 mm all as specified and directed. 80 Mild steel galvanized steel tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete of bore 20 mm all as specified and directed. 81 Refixing old steel tubing and connections of 15mm bore in new or old position (Walls, ceiling, floors etc.) including cleaning for refixing/ taking down, complete all as specified and as directed. 82 Refixing old steel tubing and connections of 20mm bore in new or old position (Walls, ceiling, floors etc.) including cleaning for refixing / taking down, complete all as specified and as directed. 83 Bib taps (Long body) 15 mm, fancy type Chromium platedwith crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs complete all as specified. 84 Stop valves/angle valve, cast copper alloy, chromium plated fancy type screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, for bore dia of pipe 15 mm, supplied and fixed in repairs complete all as specified. 85 Stop valves/(Concealed type), cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, for bore dia of pipe 15 mm, fixed in repairs complete all as specified and directed. 86 Pillar tap of 15mm bore dia fancy type capstan heads, chromium platedscrewed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed in repairs complete all as specified and directed. 87 Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe20 mm dia (minimum weight 210 gms) complete all as specified and directed. 88 20 mm dia bore gun metal globe or gate valve with iron wheel head screwed both end for iron pipe fixed in repairscomplete all as specified and directed. 89 PVC valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete, fixed in repairs complete all as specified and as directed. 90 Vitreous china squatting pan Orissa Pattern size 580 x 440 mmin white colour with integral foot rest incl lime mortor, S trap fixed in repairs complete all as specified and directed.Cat Part No-20042 (ORISSA PAN (ECO)) of Hindware or equivalent cat part of make specified in list make as approved by GE. 91 Vitreous china wash down water closet pan pedestal pattern in white colour excluding seat cover, flushing cistern and flush pipe fixed in repairs complete all as specified and directed.Cat Part No-20011 (SLICK) of Hindware or equivalent cat part of make specified in list make as approved by GE. 92 Brass chromium plated health faucet with one metre long flexible tube and wall hook fixed to iron pipe fixed in repairs completeall as specified anddirected. 93 Plastic water closet seat cover white closed pattern with flat bottom and mild steel chromium plated or aluminium hinging devices fixed in repairs complete all as specified and directed. 94 Vitreous china Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe), with brass grating and union for discharge pipe fixed in repairs, complete all as specified. 95 Repairs table top basin of size 170x835x455mm/ 565x425x140mm of whitecolour complete all as specified and directed. 96 PVC connection 15 mm size, of length 450 mm, with PTMT nuts fixed in repairs, complete all as specified and as directed. 97 Chromium plated brass towel rail 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls and fixed in repairs complete all as specified and as directed. 98 Brass chromium plated shower rose 125mm sizewith or without swivel joints, with arm any size, including fixing to steel pipe or union complete all as specified and directed 99 Repairs 15 mm two in one bib taps with flange, chromium plated, fancy type, cast copper alloy with clutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified Make: Jaquar/Cera/Prayag or equivalent 100 Reapirs 6-7 mm bevelled edge looking mirror of selected quality of size 800mmx600mm with decorative moulding edge mounted on wall with CP Brass screws & cup washers fixed in repairs copmplete all as specified. 101 Taking down eaves gutters and rain water pipe , soil and waste pipe (any size or pattern ), including all fittings, heads , shoes bends , swan-necks etc. complete all as specified and as directed. 102 110mm bore PVC SWR Type-B pipes single socket in any length with rubber joints fixed in floors etc all as specified and directed. 103 PVC SWR 110mm bore Type-B ( pressure not less than 6 kg /cm2) pipes in any length fixed to walls with PVC/MS holder or clamps complete all as specified and directed. 104 75mm bore PVC SWR Type-B pipes single socket in any length with rubber joints fixed in floors etc all as specified and directed. 105 75mm bore PVC SWR Type-B pipes single socket in any length with rubber joint fixed to wall with PVC/MS holderclamp etc complete all as specified and directed. 106 PVC SWR reducer 110mm to 75 mmcomplete all as specified and as directed, 107 PVC SWR vent cowl75 mmcomplete all as specified and as directed. 108 PVC (SWR)bend 110 mm dia any radiusall as specified and directed 109 PVC (SWR) bends any radius 110mm dia with oval access doors complete all as specified and directed. 110 PVC (SWR)junction single (single T) equal or unequal provided with access door 110 mm diaall as specified and directed 111 PVC (SWR)bend 75 mm dia any radiusall as specified and directed 112 75mm PVC (SWR) bends any radius provided withaccess door, complete all as specified and as directed. 113 PVC (SWR)junction single (single T) equal or unequal75 mm diaall as specified and directed 114 PVC (SWR)75 mm dia floor trap plain with grating including jointing with solvent cement fixed in repairs, all as specified and directed 115 PVC (SWR) branch piece, single (single Y) equal or unequal ordinary or inverted of 110 mm bore pipe complete all as specified and directed. 116 PVC (SWR) branch piece, single (single Y) equal or unequal ordinary or inverted of 75 mm bore pipe , complete all as specified and directed. 117 Waste pipe for SINK/WHB/Urinal for 32/40mm dia fixed in repairs all as specified & as directed. 118 PCC 1:2:4 type B-0 (Using 12.5 mm graded crushed stone aggregate) as in filling of pressed steel frame as in 50 mm parapet coping or in lintels upto 1.5m clear span, cills, plinth courses, string courses, coping, kneelers etcall as specified and directed. 119 Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power)complete,including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement at necessary holes for smooth finishing complete all as specified and directed complete all as specified anddirected. 120 Point wiring complete with 1.5 sqmm PVC insulated, FRLStype, ISI marked,conforming to IS-694/1990 unsheathed,multistranded,single core, copperconductor cable 1100 volts grade colour code cablesdrawn through and including PVCConduit 20 mm dia medium grade andincluding cutting, chasing work at any height and all accessories are concealedinwalls / roofs / floors / ceiling etc. metal flush boxwith top,bottom,side/back wall knockout for conduitentry from any direction made out of 1.60mm thick suitable for fixing ofmodular top cover plate as per numbers of switch modules for modular switches,sockets,fan regulators,red colour indicator, blank plates etc as approved coloursandincluding 1.5 Sqmm PVC insulated multistranded FRLStype unsheathed(Green colour),single core cable with copper conductor cable as earth continuity conductor andconnecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat including providingputty and white cementfor smooth finishing of existing surfacecomplete all as specified and directedfor theOne light point/fan /bell pointcontrolled by one switch.(Note:- Allnecessary accessories such asmodular steelbox,top cover plate, blank plate, screws,washers are to be used of same make/brand onlyand shall be deemed in to included in quoted rate only.) 121 One light point controlled by one switch 122 One 3 pin 5 amps socket point controlled by one 5 amps switch on independent board 123 One 3 pin 5 amps socket point controlled by one 5 amps switch on same board 124 All as per item No 2 (b) above but point wiring with 2.5 sqmm and earth conductor of size 2.5 sqmm complete all as specified and directed for the following:- (a) One 6 Pin 16/6 amps socket outletr point controlled by one 16 amps switch on independent board. 125 Modular type switch 10 Amps, single pole,1way,1/2 module,240V, ISI Markedcomplete all as specified and directed. 126 Modular type switch 16 Amps, single pole, 1way,1 module, 240V, ISI Marked Complete all as specified and directed.Make- Crabtree (Havells) or its equivalent in Anchor(Roma), Legrand, Seimens as approved”. 127 Modular type socket shuttered type 6 Amps, 2/3 Pin combined 2 module, 240V, AC ISI Marked Complete all as specified and directed. Make-Crabtree (Havells) or its equivalent in Anchor (Roma), Legrand, Seimens as approved”. 128 Modular type socket 16 Amps, 2/3 Pin combined shuttered socket 2 module with light indication ,240V,AC ISI MarkedComplete all as specified and directed . Make-Crabtree (Havells) or its equivalent in Anchor (Roma), Legrand, Seimens as approved”. 129 Angle lamp holder, insulated body with back plate for LED lamp including removing old unsv itemcomplete all asspecified and directed. 130 Ceiling rose, 3 terminal ,PVC/polycarbonate body ISI marked, complete all as specified and directed 131 LED light fitting 1x20W, 4 feet, 220V, general purpose surface and wall mounted LED batten with aluminium housing integrated electronic driver LED fitting connecting up with three core flexible copper conductor cable of suitable size from ceiling rose as approved by GE fixed in repairs complete all as specified and directed.LUMILINEOBS20WLED840SPCWH of Havells or equivalent cat part of make HPL, BAJAJ, SURYA, BENLO as approved by GE. 132 LED light fitting 1x10W, 2 feet, 220V, general purpose surface and wall mounted LED batten with aluminium housing integrated electronic driver LED fitting connecting up with three core flexible copper conductor cable of suitable size from ceiling rose as approved by GE fixed in repairs complete all as specified and directed.LUMILINEOBS20WLED865SPCWH of Havells or equivalent cat part of make HPL, BAJAJ, SURYA, BENLO as approved by GE. 133 LED INVERTER batten 20 watt 4 feet with square profile and poly carbonate channel lithium ion battery with charging time 8 to 10 hours and backup time upto 4 hoursand connecting up with twin core twisted copper wire from LED fitting to ceiling roseand removing old unserviceable fitting complete all as specified and directed.Make :- Pride plus inverter batten 4 feet, 20W 6500K of Havells or equivalent in Bajaj, Surya, Wipro as approved by GE. 134 LED bulb 12 watts, 240Volts,50Hzpin type andincluding removing old unserviceable itemcomplete all as specified and directed.Cat Part No-LHLDEUEEML8R012 Havells or its equivalent in Bajaj, Surya as approved. 135 LED secruity light fitting of capacity25 Watt LED street light fitting in aluminium PDC housing, toughened glass cover with IP65 protectionwith suitable inbuilt surge protector and cable connection from ceiling rose to light fitting and testing and including removing of old unserviceable item complete all as specified and directed. Make-HavellsCat Part No-ENXTP25L WH PO PC SD of Bajaj or its equivalent in Havells or Wipro as approved by GE. 136 Supply & fixing and in repair sheet metal enclosure acrylic door 240 volts AC,SPNdistribution board 8 way suitable for flush mounting with 100amps copper busbar,neutral bar,earth barand MCB incomer of rating upto 100Amps ,MCB SPN/DP,and MCB SP as outgoing and complete connecting cable linkswith top and bottom removable gland plate with IP 43 DBs protection and including making good the disturbed surfaces to match with existing surface and colour coat all as specified and as directed. Make:- Legrand cat No. 5076 21 8 way / Hager Cat Part No.VYS04G / L&T Cat Part No-DBSPN004GD as approved by GE. 137 MCB SP 6 to 32 Amps 10 KA,C series,AC,240Volts,50Hz , ISI marked fixed in repairs complete all as specified and directed.Make:- Legrand cat No.4085 87 to 4085 95 / Hager Cat Ref No.NCN106N to NCN132N / Havells Cat No.DHMGCSPF006-032as approved 138 MCB single pole & neutral 40 to 63 amps 240 volts 10 KA C series fixed in repair, complete all as specified.Make:-Havells cat part No-DHMGCSPF040or its equivalent cat part of make-Legrand / ABB / L&T as approved by GE 139 Earthing complete with galvanised steel earth plate electrode 600mmX 600mmX 6mm thick buried directly in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres belowground level, connected to and including galvanised iron wire 4 mm dia and light grade protection pipeof 15 mm diafrom earth electrode up to test point or up to 7.5mtr whichever is less by means of GIbolts, nuts, check nuts and washersall as per electrical plate No 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade,GI funnel with wire mesh,including charcoal, salt packed all around the earth electrode plate in layers, PCC earth pit chamber 1:3:6 type C1, of size 45X 45X 45 CM,RCC cover 1:2:4 type B1 of size 45X45X6CM with Reinforcement bars of 8mm dia @120mm c/c excavation/earth work in any strata and returning filling, removal of surplus soil and testing/test point for required valueincluding removing old item completeall as specified and directed. 140 Exhaust fansingle phase metal body, AC 230 Volt, 50 Hz, 900 RPMof size 300mm sweep with louvers shutter complete with all accessories including connecting up from ceiling rose complete all as specified and directed. Make:- Cat part No:- Turbo Force 1P Grey of Havellsor its Equivalent cat part of make-BAJAJ,CROMPTON GREAVES, GEC, KHAITAN,ORIENT as approved by GE 141 Sub main wiring complete with 2 runs of 6 sqmm single core copper conductor (ISI marked)cable1100 volts grade,FRLS type, PVC insulated, unsheathed, flexible, multi strandedcolour coded cables drawn throughrigid PVC conduit of size 25 mm dia medium grade(MMS) with all connected accessories such asBend,Tee,Elbow,Short peices etc concealed in wall/roofs/floorsand including one run of 2.5 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade,FRLStype as earth continuity conductor connected to common earth dollyincluding making good the disturbed surfaces to match with existing surface including taking down of old existing submain cable complete all as specified and directed. Note : - Two run of 6 sqmm single core copper conductor cable and one run of 2.5 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit. 142 Ceiling fans complete with blades. Down rods, electronic regulator and accessories, 230 volt, 1200mm sweep, min air delievery 210 CFM with service value 6 BEE five star rated with brushless direct current motor (BLDC) incl taking down existing and deposit with MES store yard all as specified and directed. “Cat Part No Zinger Make Havellsstandard or its Equivalent in Orient, Usha.” 143 Vertical double door TPNin replacementare fitted with Bus bar neutral link, blanking plates of 4 way(4+12) with suitable for incomming MCCB 4 poleG frame,having isolated neutral bar, mechanical impact strength IK09, door earthing suitable for MCCB upto 125 Amp, complete all as specified.Make:-Havells Cat part No:- DHDLVDRWGOFO04or its Equivalent cat part of make of Legrand / ABB / L&T as approved by GE. 144 MCCB 04 pole 415 volts 16 KA, 63 Amp adjustable thermal & fixed magnetic setting type suitable for TPN vertical loadline DB mentioned at ser No 15 here in before fixed in replacement, complete all asspecified.Make : Havells Cat part No IHDA3BBF0063 or its Equivalent cat part of make of Legrand / ABB / L&T as approved by GE. 145 Supply and fixing in replacementelectric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece incl making holes on walls for proper fixing with nuts and bolts complete making the surface good as per existing all as specified and directed. Make Godrej/Havells(Monza EC),or equivalent as approved.Note:-Old Unserviceable geysers shall be deposited to MES store yard. 146 Supply and laying pipe galvanised Medium Class including fittings 25mm (1.0) dia all as specified and directed. 147 Excavation in trenches not exceeding1.5 m wideand not exceeding 1.5 m deep for foundationof laying cable including gettingout in soft/loosesoil complete all as specified and directed. 148 Returning filling in including spreadingwateringand well ramming in layers not exc25cmcomplete all as specifed . 149 Removing surplus soilto distance not exceeding50 m and depositing where directed at a level notexceeding 1.5 m above the starting pointcomplete all asspecifiedand directed . 150 25 mm bore Gun-metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed high pressure with crutch or butterfly handlefixed in repairs complete all as specified and as directed. 151 Taking down burnt cable and Supply, laying, jointing and testing XLPE cable insulated, armoured, earthed, heavy duty electric cable with aluminium conductor , 1100 Volt grade, cross sectional area 50 sqmm 3.5 core including necessary cable lugs, glands, insulation tape etc complete all as specified and as directed. 152 Double walled corrugated (DWC) HDPE pipe of size 100mm including snap firt coupler conforming to IS16098 (Pt-II), SN4 pressure rating for protection of underground cable complete all as specified and directed.
