GENERAL-MGK 2025-26 COMPLETION OF FHC HALL P.NO.111/26-.-General Civil Work-- 1 Appendix A 2 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete 3 OD110483/2025-2026:Providing and fixing precoated galvanise iron profile sheets(size,shape and pitch of corrugations as approved by Engineer -in -charge) 0.35mm (+0.05%) ,total coated thickness with zinc coating, 120grams per sqm as per 1S:277 ,in 240 mpa steel grade,5-7 microns epoxy primer on both side of the sheet polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in length up to 12m or as desired by Engineer-in-charge.The sheet shall be fixed using self drilling/self tapping screws of size(5.5x55mm)with EPDM seal complete up to any pitch in horizontal/vertical or curved surfaces ,excluding the cost of purlins,rafters and trusses and including cutting to size and shape whereever required. 4 21.1.1.1:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionAnodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15) 5 OD110567/2025-2026:providing and fixing hylum board 2mm thick in panelling fixed in aluminium door window partition fram with cp brass /stainesssteel screw etc completed as per architectural drawindirection of engineer incharge 6 21.5:Providing and fixing powder coated aluminium work ( minimum thickness of powder coating 50 micron) consisting of tee /angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-Charge ( level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately ). 7 50.12.4.2:Providing and fixing false ceiling with 7.5 mm thick PVC wooden grains panel board ceiling of approved quality in aluminium frame work with necessary screws etc complete ( aluminium frame work shall be paid separately) 8 OD96368/2025-2026:Providing and laying Ceramic Antiskid floor tiles of size 300x300mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. 9 50.13.1:9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete 10 OD110603/2025-2026:Engaging Coolie for Miscellaneous Works 11 OD110685/2025-2026:Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.(MODIFIED 14.43 OLD) Details of cost for 10 sqm 12 13.46.1:Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 13 2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil 14 51.2.3:Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade 15 OD110895/2025-2026:Supplying and laying interlocking cement concrete paver block tiles 80mm or nearest size ,thickness,minimum strengh M40(conforming to IS 15658:2006),for Medium Traffic Low volume roads) including providing a layer of 6 mm aggregare for 5 cm thickness,then laying interlock CC paver block tiles in lines and levels as per the directions of the the departmental officers at site,inclusive of all cost &amp:conveyance charges...et.Complete [MoRTH 55.23]
