Tender For Provision Of Pi Mess For Jcos/Or At Ncc Gp Hq Gorakhpur; 1 Lump sum price worked out by the contractor as per showm on drawing for Building Work as listed in Sch ‘A’ PartI. 2 Lump sum price worked out by the contractor for Internal Water Supply as listed in Sch A Part II. 3 Lump sum price worked out by the contractor for Internal Electrification as listed in Sch A Part III. 4 Lump sum price worked out by the contractor for Sewage Disposal as listed in Sch A Part IV. 5 Lump sum price worked out by the contractor for Path as listed in Sch A Part V. 6 Lump sum price worked out by the contractor for Area Drainage as listed in Sch A Part VI. 7 Lump sum price worked out by the contractor for External Electric Supply as listed in Sch A Part VII. 8 Lump sum price worked out by the contractor for External Water Supply as listed in Sch A Part VIII. 9 Lump sum price worked out by the contractor for Site Clearance and Earth Work as listed in Sch A Part IX. 10 Price item wise worked out by the Contractor forSchedule `A Part-X (rate against Srl No. 11.0 to 22.00 shall be quoted by the Contractor) 11 S&F metal flush box 12 module, made of 1.6mm thick sheet, for mounting modular switches and sockets complete all as specified and directed. 12 S&F white modular cover plate with frame 12 module, for modular switches and sockets complete all as specified and directed. 13 S&F metal flush box 8 module, made of 1.6mm thick sheet, for mounting modular switches and sockets complete all as specified and directed. 14 S&F white modular cover plate with frame 8 module, for modular switches and sockets complete all as specified and directed. 15 S&F wall mounted fan voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 300mm complete all as specified and directed. 16 Material and labour Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick directly burried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of earth plate not less than 1.5metre below the ground level connected to GI strip 32x6 mm by means of bolts nuts check nuts and washers of galvanised iron at 2 points & GI pipe 40 mm bore medium grade for protection of earth strip and 20 mmbore medium GI pipe for watering including adequate quantity of charcoal dust and common salt around earth plate,PCC chamber 1:3:6 (type C-1) using 20mm graded stone aggregate, funnel with wire mesh, 50 mm thick cover of RCC 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8 mm MS bars at 150 mm centre to centre both ways, CI frame and charcoal dust and common salt, all as shown in electrical plate No. 3 of MES SSR part-I and making test point as specified including excavation & earth work in any type of soil and connecting the earthing to an earthing point/equipment & testing on completion complete all as specified and directed. 17 Boring of holes under road, pavement, hard standing manually including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure complete all as specified and directed. 18 Supply, install, testing and commissioning of LT Cubicle panel of suitable size, outdoor type(Slopy roof), platform mounted, totally enclosed, dust and vermin proof, openablefrom both front and rear side, double door, outdoor sheet made out 3.15mm and indoor sheet of 2mm thick CRCA sheet complete including inner chambers/partitions to mount the following electrical accessories and built upon 50x50x6mm angle iron frame work, having front and rear hinged doors with 04 Nos hinges on each leaf, lifting lugs (2 Nos), provision for earth strip connection, bottom detachable gland plates, connecting using suitable size of zinc plated and passivated nut, bolts , springs and washers.The cabinet and all members should be chemically treated with anti-corrosive chemicals and apply spray paint with two coats of synethetic enamel paintover a coat of red oxide primer. The panel should be suitable for 415 volts, 50Hz, 3 phase 4 wire system 1100 volts grade, with copper bus bar of 200 Amps capacity rating coloured heat shrinkable sleaving, internal connection should be provided with aluminium strip of suitable size and necessary grouting/ foundation all as required at site and comprising of following :-Incoming(a) MCCB 125Amps, 35 KA, 3 Phase, 4 pole,microprocessor based with overload protection adjustable rating of 30%to 100%in variable time rating short circuit protection adjustable type range 400% to 1000% with variable time setting , ground fault adjustablein range 10% to 40% of variable time setting -01 set 19 (b ) Ammeter96 mm square digital type with selector switch and CTincluding necessary connection of suitable size of copper wire-01 set(c) Voltmeter 0-500V -01 No digital type 96 mm square with selector switch including necessary connection with suitable size ofcopper wire - 01 set(d) LED indicator lamp(R-Y-B)- 01 setOutgoing(a) MCCB100A, 35 KA. 3 Phase, 4 pole,microprocessor based with overload protection adjustable rating of 30%to 100%in variable time rating short circuit protection adjustable type range 400% to 1000% with variable time setting , ground fault adjustablein range 10% to 40% of variable time setting -01 No (b) -do but of MCCB 63 Amps, 35 KA, 3 Phase, 4 pole - 01 No (spare)(c) MCB TPN 32 Amps - 01 No(d) MCB SPN 10 Amps-01 No(e) Astronomical Timer relay alongwith 63 Amps TP Contactor and 40 Amps MCB for each circuit for street light-01 20 S&F Weather Proof thermo plastic (Polysterene) Cable Junction box , having protection class IP-66 and of overall size 210mm x 155mm x 92mm having metric knockouts on the wall, duly fixed with the pole with aluminium strip (25x3mm) clamp, GI bolts, nuts, washers and 2 Nos polymide weather proof cable glandsof cable sealing range 10mm to 17mm (Complete with check nut) and including 1 No 30 Amps with cable connector and 1 No. 6 Amps SP MCB.
