Tender For Development Of Tharangambadi At Mayiladuthurai District As A Tourist Destination.
Tender Value
Ref. Documents
Estimated cost
Bid Submission
07 Aug 2025
0 days left
EMD
2.70 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tharangambadi → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Development Of Tharangambadi At Mayiladuthurai District As A Tourist Destination.
BOQ
| Sl. No. | Item Description |
| 1 | Clearing the Heavy Jungle by using tools, machineries and the same properly stacked away from the work spot.The Rate inclusive of cost of Labour and hand tool,etc,.complete as directed |
| 2 | Earth work NARROW excavation in hard stiff clay, stiff black cotton etc., for foundation including shoring,strutting and baling out water wherver necessary,dewatering etc., complete as direcdted by the departmental officer |
| 3 | Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification. |
| 4 | Refilling with excavated earth other than crushed stone sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officersin layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification |
| 5 | Filling with m-sand to the foundation and basement including watering and consolidating etc. as complete with all respects complying with relevant standard specification as directed by the departmental officers. |
| 6 | Providing and laying spreading and compacting graded stone aggregate to Wet Mix Macadam(WMM) specification including premixing the material with water at OMC in machanical mix plant carriage of mixed material by tipper to site laying in uniform layers 250mm thick with pavers in SubBase/Base course on well prepared surface and compacting with vibratory roller to achieve the desired density including cost of material,labour charges, rentals for machinery, fuel and all other incidental charges etc., complete. |
| 7 | Supply and laying in position of dressed stone slab of 50mm thick Flammed of 300mmx 300mm over a sand bed of 100mm thick and Pointing the joints to full depth with Cement mortar 1:3 as directly byDepartmental officers etc., complete compling with standard specifications. |
| 8 | Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. as complete. with all respects complying with relevant standard specification as directed by the departmental officers. |
| 9 | Cement Concrete 1:2:4 (One Cement, Two sand and Four hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete as directed by the departmental officers. |
| 10 | Providing and fixing Kerb Stone of size 0.45 X0.15 X 0.30 Mtr of RCC precast concrete by a new one of following size in RCC 1:2:4 mix using 20mm gauge hard broken graninte stone jelly and river sand excluding cost of reinforcement but including charges fabrication charges curing neat finishing etc., and labour charges for fixing the jally in position complying with standard specification as directed by the departmental officers etc., complete |
| 11 | Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc. as complete with all respects complying with relevant standard specification as directed by the departmental officers. |
| 12 | Painting new iron works such as MS flats ,ISMB, Sections and other Steel Works etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 13 | Supplying and laying of country wood scantling including as directed by the departmental officers . |
| 14 | Supplying and laying of country wood plank including as directed by the departmental officers . |
| 15 | Supplying of Eucalyptus Poles of 15cm dia including as directed by the departmental officers . |
| 16 | Supplying laying and jointing of 100mm dia MS pipeand80 x 40mm Rectangular MS pipe with all required special including cutting threading and welding etc., as directed by the departmental officers. |
| 17 | Supplying, laying and fixing of roof pre-aluminuam Zinc steel sheet (Galvalume) 550 mpm0.47mm thick with ridge sheets of approved quality including the cost of necessary fixing meterials, drilling, roofing with proper joints and labour charges for bending and ceiling to roof sheets to requiredsizeand shape laying and fixing charges etc., as directed by the departmental officers . |
| 18 | Supplying of Ms Fabricated Portable Toilet Cabin Of Size (16\"x06\"x8.6) With Necessary Electrical and Sanitary Fittings.Attached Western Toilet Cabin Of Size (5\"x6\"x8.6\") With Necessary Electrical and Sanitary Fittings EWC, Wall mixture, Health faucet, Soup holder, Towel holder, Wash basin, Flash tank, Water Tap, Exhaust Fan With Louvers, Water tank, Inside Acp Wall Cladding Anti-Skid Tile Flooring With 4\" Skirting including as directed by the departmental officers. |
| 19 | Supplying of FRP cosmo crete bio septic tank with capacity of 20000 liters of size (18.7\"x7.5\"x7.8\") with thickness of 10mm including as directed by the departmental officers . |
| 20 | Supplying, laying, jointing in position of best quality110 mm dia PVC waste pipe (6kg / cm) of approved make (Finolex) and providing leak proof joints including making connection to all sanitary fittings, dismantling, masonry, RCC works wherever necessary and making good and dismantled portion etc. as complete with all respects complying with relevant standard specification as directed by the departmental officers. |
| 21 | Supplying, laying and jointing the following dia PVC specials suitable for 6kg/cm2 pipe etc. as complete with all respects complying with relevant standard specification as directed by the departmental officers. |
| 22 | 110mm PVC Elbow |
| 23 | 110mm PVC Bend |
| 24 | Supplying, laying and jointing UPVC pipes 32mm dia(having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level etc. as complete with all respects complying with relevant standard specification as directed by the departmental officers.The PVC pipes shall be got approved by Executive Engineer before use on works. |
| 25 | Supplying UPVC Specials of 32mm (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements.Since the labour for cutting, threading / pasting, sundries have already been included under pipe line item of works, no separate provision for fixing UPVC specials needs to be allowed |
| 26 | 32mm UPVC Elbow |
| 27 | 32mm UPVC Tee |
| 28 | 32mm UPVC Coupling |
| 29 | Supplying of PUFF ticket counter - Dimension 9\"x9\"x7\" .The main structural member of MS Square & Rectangular Pipe to form a shell for wall panels shall be made out of 50mm thick Puff Panel Roof.Roofing made of 30mm thick puff sheet. The floor made of MS Structure and 18mm Cement Board, top with vinyl flooring.Door with suitable locking arrangements .Electricals 4FT LED Fitting with Bulk head fitting outside the door with necessary internal wirings. switch and sockets WRTING TABLE 1.5FT Inner side only. 9X2.5FT UPVC Window on two side ncluding as directed by the departmental officers . |
| 30 | Supply, fabrication and installation of 160 Amps ON LOAD Change over panel made out of CRCA sheet steel enclosure welded construction with metering arrangements and bus bar flour mounted with suitable angle MS frame including earthing with following switches. Incoming: 160 Amps 4 Pole SDF ON Load Changeover Switch - 1 NoOutgoing: 32 Amps 4 Pole SDF switch - 10 NosBus Bar: 100 x 100 x 6mm (For R,Y, & B) 75 x 75 x 6mm (For Neutral) |
| 31 | Supply and fixing of ARCHITECTURAL POST TOP POLE 6M height Single Arm Pole Made of steel pipe section of 102mm dia. Top Decorative Castore design bracket made in combination of steel pipe sections 60mm dia.(vertical), 42mm dia.(vertical & gradually bent ) & Gradually Bent 14mm dia. MS rods. Ms rods are bent in such a way that it connects between two edges of 42mm dia. pipe, thus forming a loop. Bracket has decorative middle flower of dia 140mm along with a casted rod- weight-2.65 kgs. Multiple cast iron components such as Large leaf 370 mm long - starting width 100mm and ending width 150mm & weight-3.75kgs.,small leaf 190mm long , starting width 40 mm and ending width 140mm.- weight-1.2kgs. are provided at different places for aesthetics. Entire bracket shall be made to get 770mm horizonal arm length & provide pleasing aesthetics. Decorative Base in Steel - Its design starting with dia 350mm for 228mm height, then tapers to 241mm, followed by a cylindrical section of 219mm dia., 490mm Height. It ends with a Top section consist of a Ring of 276mm dia. and 54mm height followed by a taperinng section with Bottom dia. 235mm, Top dia 144mm and Height of 123mm. Total Height of the Base is 940mm. A Steel base plate of 400mm x 400mm is welded at the bottom of the base. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. Decorative cast iron flower starting with a dia 142 mm increasing gradually to 215mm and then tapering to a dia 133mm. Total height of cast iron flower is 304 mm & weight is 15kgs.. Decorative cast iron pole top starts from bottom with a ring section of dia. 67mm followed by a ring of dia. 75mm, radially incrases to 100mm dia. for a height 15mm,then radially reduces to 46mm for a height 20mm followed by a jack shaped section(45mm(W & 20mm(H), followed by a ring of dia. 60mm which is followedby a Conical section(bottom dia. 40mm & top dia.10mm,140mm(H) with sphere shape(30mm dia.) on top-total height of the pole top is 260mm & weight is 2.5 Kgs. All cast iron parts weight mentioned are with +/- 5% tolerance. Entire pole including the decorative elements shall be made to provide pleasing aesthetics as approved by Architect/ Engineer in-charge. After Fabrication, Entire Pole should be hot dip galvanized(60 microns Minimum ) for the effective corrosion resistance. The pole should be provided with an inbuilt junction box with 1No. 32A Heavy Duty Stud type connector and 1No. 6A SP MCB, at the bottom- the inbuilt box should have a flush door of suitable size. Wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole strength. Pole & Cast iron parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint. Sample should be submitted for approval from Architect/ engineer-in-charge. Approved Makes - NERI/ DW WINDSOR/GHM. |
| 32 | Supply and fixing of LIGHT21, 45W-55W, PowerModule LED, 3000K, IP66,Suspended Upper frame with threaded coupling G3/4\"for suspended mounting at the top,made of die cast aluminum using pressure die- casting process. in single piece.Bottom frame composed by a ring with Company /brand name engraved in the mold,made of die cast aluminum using pressure die-casting process. in single piece. Auxiliary and optical compartment can be accessed by opening the frames. Drop shaped screen in polymethylmethacrylate (PMMA), transparent. Shock resistance IK06 made in single piece by injection moulding process. Pure polyester powder coating in Customized Metallic Grey Colour. Silicone gasket between the upper and lower frames ensures IP Rating - IP 66. Height – 545mm,Diameter- 550mm,Weight - 8Kgs., Area Exposed to Wind(S) - 0.135m2Power LED Module with Company /brand name printed on PCB with the metal core plate. LED chips of CREE/NICHIA/OSRAM/LUMILED make shall be used. Colour Rendering Index: Ra > 70.Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage& Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA/PC . LED Lifetime >1,00,000hours. LM80 report from LED Manufacturer should be submitted.Safety test report as per IEC 60598/IS 10322 from UL/UL Authorised/3rd party NABL should be submitted. LM79 report also should be submitted from UL/UL Authorised/3rd party NABL Laboratory. BIS Certificate with manufacturer name same as brand proposed should be submitted. Sample should be submitted for approval from concerned engineer-in charge.Approved Makes - NERI/ DW WINDSOR/GHM |
| 33 | Supplyand laying of following PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. |
| 34 | 3½x 50 Sqmm |
| 35 | 3½x 25sqmm |
| 36 | Supply and fixing of brass cable gland for the following PVC armoured LTUG cable with earth connection |
| 37 | 3½x 50 Sqmm |
| 38 | 3½x 25sqmm |
| 39 | Supply and providing cable end termination of the followingPVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete |
| 40 | 3½x 50 Sqmm |
| 41 | 3½x 25sqmm |
| 42 | Earthing as per the ISI specification with an earth electrode of 2.10 metre Class \"B\" GI pipe of dia not less than 40mm with copper earth plate of size 125mmx 50mmx 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry. |
| 43 | Supply and Run of1 of No.8 SWG copper wire for earth connection. |
| 44 | Supply and Run of 3 of 4 sq.mm.PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigidpipe on wall and ceiling with continuous earth wire connection of 4 sq.mm copper wirewith painting of suitable colour. |
| 45 | Supply and fixing of 20 Meters Highmast GI polygonal pole suitable for 6 Nos of 300 Watts LED Sports Luminaire IP66, IK08, 5700K with system efficiancy at least 100 Lumens LED luminaires with aviation lamp with motorized lantern carriage with suitable conrete foundation and timer control units including erathing system arrangement etc., complete. |
| 46 | GST at 18% |
AI Tender Summary
Tender Timeline
Jul 24, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedAug 07, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 08, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender