Providing And Fixing Of Various Ancillary Works At Microbiology And Anatomy Department Of H. B. T. Medical College.- 1 Providing & fixing of various ancillary works at Microbiology & Anatomy department of H. B. T. Medical College. 2 INDOOR LED FIXTURES - -LED Square Recessed Downlighter36W (600X600) 3 Exhaust fan of 450mm sweep, 1400RPM, with 3650 CFM free air delivery, AC 415V , 50 Hz, Three phase complete with all necessary accessories for completing installation 4 Wall mounting air circulator of 600mm sweep, 230 Volts,AC 50 Hz, oscillating type complete with all necessary accessories for completing installation. 5 Submains FRLSH Casing N Caping - 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire in 20 x 12 mm (1/2) 6 Light /Fan / Ex. fan Points 7 25 mm X 12 mm - Casing-Capping 8 25 mm.- Only PVC Conduits 9 Supply and fixing 20 mm thick Marine Ply Plank 10 Replacement of door closer 11 Providing and fixing in position Curtain rod of aluminium powder coated circular tubular section including the fixing sockets on both sides 12 Providing and fixing aluminium kickplate of required width to flush and any door shutter using 24 G aluminium sheet with 3 coats of painting etc. complete 13 Providing & fixing of Tower Bolt 14 Providing & fixing of Handle 15 Removing & Regixing of Door along with shutter 16 Providing and fixing mortise lock of approved make manufactured as per IS:2209 and 6607 and as described below for doors with necessary fixtures and materials and labour etc. complete 17 Providing and applying first single coat of approved primer and two coats of synthetic enamel paint/flat oil paint of an approved make and colour as per manufacturers specifications to the metal purlins not more the 150mm in height, at all height and locations as directed including removing the existing paint by burning, cleaning, preparing the surface for painting etc. complete as directed by Engineer-in-charge. 18 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 and above in foundations and plinth in : 19 Providing and applying 12 mm thick internal sand faced plaster in cement mortar 1:3 at all heights and locations in one coat for masonry (except stone masonry) and concrete surfaces including racking out joints, hacking of concrete surface, watering, finishing, curing, scaffolding etc. complete. 20 Removing any type of flooring i.e.mosaic, cement marble, granites non-slippery, tandur, kotah, shahabad stone or Indian Pattern stone, glazed tiles in flooring including bedding brick bat coba , paver blocks of any thickness etc in open passage, footpath, or any flooring laid on ground mechanically or manually and delivering materials in Ward Office and carting away unserviceable materials. 21 Grading roof and toilet for water proofing treatment above slab withCement mortar 1:3 (1 cement : 3 coarse sand) 22 Providing and fixing polished natural stone tiles as specified below of approved quality, pattern and colour for dado including preparing the surface and levelling in the desired line, backing of 20 thk. cement mortar in porportion 1:3, square cut top edge or chamfered top edge in cement mortar 1:3, cement float, machine cutting, leveling, jointing, filling the joints with neat cement or pigment mixed with cement, polishing, finishing, curing etc complete as directed by Engineer In Charge. 23 Providing and fixing all sides polished natural stone as specified below of approved quality, pattern, colour and thickness for door and window frames / architraves including preparing the surface and levelling in the desired line, machine cutting, jointing in approved adhesives, leveling, smooth cement plastering along the sides to match the existing surface in cement mortar, filling the joints with pigment mixed with cement, cleaning, finishing, curing etc complete as directed by Engineer In Charge. 24 Supplying, laying, jointing & testing UPVC Drainage class pipes of FoamcoreAstral(SN 8) or equivalent make in solvent cement joint including leveling with cutting the pipe to required length, roughining of pipe at wall joint including socket as directed: 150 mm pipe 25 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4, U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer in Charge 26 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.15 mm dia nominal bore 27 Providing and fixing stainless steel sink 600 mm x 450 mm and 200mmdeep including 32mm dia. galvanised iron waste pipe, 32mm dia. C.P.brass waste coupling, one C.P. brass screw down tap, caste ironbrackets, rubber plugs with chain etc. complete. 28 Providing & Fixing 100mm diameter Nahani trap Jali in steel finish with necessary fixing required to make the item well functional. 29 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 30 Providing & fixing of SS staining stand19x13x7.6 31 Repairing, fabrication & Greasing of biosafety cabinet Stand
