|
| 1 | Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following depths, below natural ground / Road top level In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc.Depth upto 1.5 m |
| 2 | Random rubble dry stone Kharanja (soling) under floor. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : 1:3:6 (1 Cement : 3 fine/ coarse sand : 6 graded stone aggregate 40 mm nominal size). |
| 4 | 1:1½:3 (1 Cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size). |
| 5 | Brick work with FPS bricks of class designation 75 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 6 | Construction of embankment with approved material obtained from borrow pit with all lifts and leads, transporting to site, spreading, grading to required slope and compacting by vibratory roller 8-10 tonne to meet requirement of table 300-2 including cost of compensation for earth taken from private land complete as per MoRT&H specification clause 305. (Lead taken upto 5 km) |
| 7 | Cement plastering including T&P, scaffolding, material and complete labour, including cost of water, curing, racking of joints etc. with 20 mm cement plaster of mix : including Providing /mixing of synthetic fibers compulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar 1:3 (1 cement : 3 fine/ coarse sand) |
| 8 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.Jhunjhunu / Jalore (Red / Chocolate Colour) |
| 9 | Finishing wall with water proofing cement paint of approved brand and manufacture and or required shade to give an even shade including all scaffolding: New work (Two or more coats applied @ 3.84 kg/10 sqm). |
| 10 | Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 11 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture |
| 12 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 13 | SITC of Single Stage, water cooled, High Speed (2880 RPM), Horizontal, Centrifugal, Openwell Submersible pumps set pre filled with coolent water and fitted with mechanical seal - T/C Vs T/C, Thrust bearing shall be of carbon + S.S.The stator body of single phase pump shall be of SS and rest of all shall be of cast iron. All casting parts should be cathod electro deposition (CED) coated and other construction material should be confirming to IS : 14220: 2018 . The overall performance of pump shall confirm to BEE energy efficiency level of 3 star. Valid BEE certificate from OEM must be submitted for the same. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011, including making connection etc as required complete in all respect. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .3.0 HP, 3-Ø, (17 -27) Mtr, (680 - 300) LPM |
| 14 | SITC of Contactor OEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Cordinatiom Chart and made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFF push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR .3.0 HP to 5.0 HP ( Star / Delta starter ) |
| 15 | P & F of IP 68 protected LED underwater light system with Die cast housing, toughened glass diffuser, 9 X 1W, 12V DC LED lamps with dynamic color changing capability available in quick connecting cable coupled with various mounting accessories. Ability to create 16.7 million uniform, smooth and brilliant colors without revealing any lamp image. Available in 5 colors – amber, green, blue, red and white. |
| 16 | Supply and laying PVC Insulated and PVC Round Sheathed Multi Core copper conductor (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing pipe / open trench / Cable tray / on surface including making connection etc. as required. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSR 2.5 sq.mm x 4 core |
| 17 | P/Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, existing pipe / open trench / Cable tray / on surface including making connection etc. as required. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSR 4.0 Sq.mm 3 core flat / Round |
| 18 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it\"s own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure \"A\" attached with this BSR 50.0 Sq. mm 3.5 core |
| 19 | Supply and fixing of Dr Bheem Rav Ambedker statue on RCC/Stone Masonry structure platform at Masooda of Rajasthan. Supplying and fixing atSite of Bronze Metal Alloy (88% Copper, 8% Tin and 4% Zinc) sculpture Including Planning, developing, casting, all loading-unloading,Transportation, scaffolding, hoisting, installation with all required T&P, fixing over base/surface as per shape-size & placement as per approved Drawing, finishing, surface treatment etc. covering properly till the date of Opening /inauguration of site etc. Modeling, 3D scanning of model Robotic Machining (enlargement of model to desired height), assembling and final detailing, Piece molding, Wax casting (Lost wax process), Wax chasing, sprung Investing, metal casting, Divesting, metal chasing. Brazing/Welding Finishing and Painting/Color etc. Complete job in all respect as per Approved design & drawing under approval of project consultant, appointed for the project & as per directions of Engineer-In Charge. (Theme, concept plan, schematic arrangement, other relevant details and drawings of element/statue/sculpture are enclosed. The height of sculpture is 6 feet and Weight approximate 600-650 kg. The final drawing shall be provided after award of the work.) Note: Payment shall be made per kg of the finished Sculpture (final payment shall be paid after test result of composition-If variation in composition of alloy metal observed the rate shall be paid accordingly). Other masonry. concreting, steel reinforcement plastering etc. required shall be paid extra but additional support if required for bronzemetal alloy sculpture, shall be of Stainless steel/zinc coated iron steel etc.for which nothing shall be paid extra |
| 20 | Supply and fixing Glass Mosaic tiles of 20 X 20 X 4 mm size of approved shade and design with required adhesive over bed of 15 mm thick cement, sand mortar 1:3 including nicely finished joints. Thickness of joints shall not be more than 1.5mm using water proof joints filler (as recommended by manufacture)& finished with flush pointing in white cement mixed with pigment to match the shade of tiles. Complete work as required in all respect. |
| 21 | Designing, supply, erection, commissioning and testing ofBubbler Jet/ Vertical Aerating Jet Fountains. The Bubbler Jet nozzles made of brass with nickel plating with excellent finish complete in all respect make Famous fountains |
| 22 | SITC of Swing Joints made of Brass nickel plating with excellent finish complerte in all respect make Famous Fountains |
| 23 | Supply, Installation, testing and Commissiongof 15ft Dia Ring Made of 2-1/2\" GI B class pipe with welding of Flanges, scokets, nut bolts including complete powder coating on surface. |
| 24 | Providing and fixing of DMX Based 7-station Microcontroller basedLed Light controller suitable for led lighting system with 12 V DC/50A Output. |
| 25 | Designing, supply, erection, commissioning and testing ofPlumbing In 2\" GI B class/UPvc Pipes Make-TT Swastik/JIndalas per site, Diffuser Nozzles for Water Fall Effects,Welding of Riser Sockets, Flanges welding, Inlet Sockets, Unions, Sockets etc. Complete pipe and fitting are powder coated with required Header for Pump Connection |
| 26 | Providing & Fixing of 4\" S.S. 304 grade wire mesh Mesh Filter forPump filtration of water at inlet of mono submersible pump. Filter made out of M.S.Sheet & Flats with inlet threaded nipple as per pump inlet. The S.S.mesh fitted on filter body with Screws. |
