Construction Of Three (3) Nos. Of Hutments For Providing Bachelor Type Accommodation (13 Nos.) In Connection With Day To Day Operation And Upkeep Of Palla Inspection Bunglow Belonging To Gov Wb, Iwd In Vill-Palla, Block- Memari-I, & P.S- Memari. Dist.- Pu
Tender Value
19.03 Lakhs
Estimated cost
Bid Submission
06 Aug 2025
0 days left
EMD
38068
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
memari → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction of three (3) Nos. of hutments for providing bachelor type accommodation (13 nos.) in connection with Day to Day operation and upkeep of Palla Inspection Bunglow belonging to Gov WB, IWD in Vill-Palla, Block- Memari-I, & P.S- Memari. Dist.- Purba Bardhaman
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation of foundation trenches ordrains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading ortacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out waters required complete. (a) Depth of excavation not exceeding 1,500 mm. |
| 2 | B) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating thesame by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)(B) Do - by fine sand |
| 3 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 4 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in gound floor as per relevant IS codes.a) Pakur Variety |
| 5 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. |
| 6 | 25 mm to 30 mm shuttering without staging in foundation |
| 7 | Ordinary Cement concrete (mix 1:1.5:3)with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.Pakur varity. |
| 8 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.For works in foundation and upto roof of ground floor/upto 4 m Tor steel/Mild SteelSAIL/ TATA/RINL |
| 9 | Brick work with 1st class bricks in cement mortar (1:4)In superstructure, ground floor |
| 10 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. |
| 11 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface]With 1:4 cement15 mm thick plaster |
| 12 | Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer\"s specification.In Ground floor:One coat on new surface. |
| 13 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals).(f) Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak. |
| 14 | (a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.(i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr. |
| 15 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work)(a) With earth obtained from excavation of foundation. |
| 16 | M.S. structural works in roof trusses with tubular sections conforming to IS: 806-1968 & IS: 1161- 1998 cnnected to one another with bracket, gusset cleats as per design, direction of Engineer-in-charge complete including cutting to requisite size, fabrication with necessary metal arc welding conforming to IS: 816- 1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete.The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour reqired for the work including all incidental chages such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural tubular memebrs as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with weight of finished structural members. The rates are considered for a height of erection 8 m. / 2nd floor level from the ground. Add 1.5 % extra over the rate for each additional floor or 4m. beyond the initial 8 m. or part thereof.i) For trusses spanning up to 12.00 m |
| 17 | Supplying, fitting & fixing Industrial Troughed Aluminium sheet (excluding the supporting frame work) of approved make & brand in alloy 3105 conforming to IS: 1254-1991 fitted and fixed with 75 mm & 25 mm Self tapping screw, EPDM Washer 16 mm dia & 3 mm th washer etc complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work) (Aluminiumsheet to be supplied by contractor).(i) In Roof:-b) With 0.71 mm thick sheet |
| 18 | Galvanised iron sheet ridging fitted with necessary bolts,screws, washers etc complete.(225mm end lapping)(A) 300 mm lapping each way(a) With 0.60 mm sheet. |
| 19 | Galvanised iron sheet eaves gutter fitted and fixed with necessary 50 mm X 6 mm M.S flat bar clamps bent to design, bolts, nuts, washers etc. complete. Eaves gutter made of 0.63 mm. sheets.(300mm End lapping) (b) 300 mm. wide gutter. |
| 20 | (a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 21 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(b) On steel or other metal surface :With super gloss (hi-gloss) -iv) Two coats (with any shade except white) |
| 22 | Panel shutters of door and window, as per design (each panel consisting of singleplank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings.In ground floor.(In case of non-supply of single plank, penal rate of reduction of 20% will be made)(ii) 40mm thick shutters with 19mm thick panel of size 30 to 45 cmb) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. |
| 23 | (b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 24 | A) Painting with best quality synthetic enamel paint of approved makeand brand including smoothening surface by sand papering etc. includingusing of approved putty etc. on the surface, if necessary :(a) On timber or plastered surface :With super gloss (hi-gloss) -(iv) Two coats (with any shade except white) |
| 25 | Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor.iii) 35 mm thick. |
| 26 | Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. |
| 27 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.a) Area of each tile upto 0.09 Sq.m(i) Coloured decorative |
| 28 | (B) WallWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. b) Area of each tile above 0.09 Sq.mi) Coloured decorative |
| 29 | Supplying,fitting & fixing in position suspended false ceiling with frame work of aluminium hollow section of size 50mm X 25mm (2.0mm thickness) combined with aluminium corners of size 38mm X 25mm, suspended by aluminium hollow tube section of size 38mm X 25mm having size of 600mm X 600mm ceiling with aluminium composit panels (ACP) - Interior grade of thickness 3.0mm comprising of proctective film, polyester coating, primer, aluminium coil, adhesive film,polyethylene core again with one layer adhesive film, aluminium bottom coating and finally service coating as per manufacturer\"s specification finished with aluminium screw and silicon sealent complete in all respect including all incidental charges etc. as per direction of Engineer-in-charge. |
| 30 | Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of 59 mm x30 mm section with 2.0 mm (+/-0.2 mm) wall thickness.Horizontal & vertical section shall be fixed to each other by self tapping screws and 1 solid polymeric or M.S. galvanised tubular \"L\" shaped bracket 100mm x 200mm in each corner of the shutter frame for placing hinges. Polymer based multicavity hollow section of 120 mm x30mm with 2.0 mm (+/- 0.2 mm) wall thickness will be fitted in the middle, reinforced by solid polymer bar of 200 mm long at both ends and screws from both sides as lock rail. The section frame will then be fitted in by PVC panels of size 100 mmx25 mm with wall thickness of 1.2 mm (+/- 0.2 mm) and 2 nos. of 6 mm dia bright rod will be inserted horizontally with both side check and nut system and stretches where fixing ofhinges / hasp bolt / tower bolt / door ring are required to be strong enough to with stand wear and tear. The rate is inclusive of cost of all materials, labour, and hire of tools and plants and appliancesi/c carriage of all materials taxes and all other incidental charges complete. |
| 31 | Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to bem reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm long M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer’s specification and direction of Engineer-in-Charge. |
| 32 | Iron hasp bolt of approved quality fitted and fixed complete(oxidised) with 16mm dia rod with centre bolt and round (c) 300mm long. |
| 33 | Iron socket bolt of approved quality fitted and fixed complete. (d) 225mm long x 10mm dia bolt. |
| 34 | (a) 75 mm long x 10 mm dia bolt |
| 35 | Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple,longscrew, reducing socket, reducing tee, short piece etc. fitted withholder bats clamps, including cutting pipes, making threads, fitting, fixingetc. complete in all respect including cost of all necessary fittings asrequired,jointing materials and two coats of painting with approved paintin any position above ground. (Payment will be made on the centre linemeasurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting willbe made seperately)(B) For Concealed Work(a) 15 mm dia. medium quality |
| 36 | (c) 25 mm dia. medium quality |
| 37 | Supplying, fitting and fixing shower of approved brand and make.(b) Chromium plated Rose shower with revolving joint and 150 mm long shower arm (Equivalent to Code No. 5489 & Model - Florentine of Jaquar or similar brand). |
| 38 | (d) Chromium plated Hand shower with Flexible Tube & fittings(Equivalent to Code No. Hsh-1937 & (Equivalent to Code No. 5037 & Model - Florentine of Jaquar or similar). |
| 39 | Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only).(vi) 32 mm dia |
| 40 | Supplying, fitting and fixing bib cock or stop cock.(g) Supplying, fitting and fixing alloy iron with brass spindle bib cock/ stop cock of approved brand and make, spray painted and tested to 21 kg per sq. cm(ii) 20 mm |
| 41 | Supplying, fitting and fixing White Vitreous China best quality approved make wash basin with C.I. bracket on 75 mm. x 75 mm. wooden blocks, CP waste fittings of 32 mm dia, one approved quality brass CP pillar cock of 15 mm. dia, CP chain with rubber plug of 30 mm dia, approved quality PVC waste pipe with CP nut 32 mm dia 900 mm long approved quality PVC connection pipe with heavy brass CP nut including bending good all damages and painting the brackets with two coats of approved paint.(ii)550mmx400 mm Size |
| 42 | Supplying, fitting and fixing pedestal of approved make for wash basin.(white) |
| 43 | Supplying, fitting and fixing pillar cock of approved make.CP Pillar Cock - 15 mm. (Code No. 5011 & Model - FL ORENTINE of JAQUAR or equivalent. |
| 44 | Supplying, fitting & fixing Cast iron soil pipe only conforming to I.S. 3989 / 1970 and I.S. 1729/1964 with bobbins, nails etc. including making holes in the wall, floor etc. and cutting trenches etc. in any floor through masonry concrete, if necessary, and mending good damages with necessary jointing materials and painting two coats to the exposed surface with approved paint complete. (Measurement will be made along the center line of the total pipe line in fitted condition including specials,payment for specials & Painting will however be paid seperately).(a) With valamoid joints including sealing with sand cement morter (4:1) upto quarter depth.100 mm dia. (internal). |
| 45 | Supplying fitting & fixing Anglo Indian W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc.b) with S trap (with vent). |
| 46 | Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete.(i) 635 mm X 395 mm X 420 mm. |
| 47 | Supplying, fitting and fixing 10 litre porcelain low-down cistern of approved make with either side or bottom inlet, side overflow, brackets complete with all internnal PVC fittings.White |
| 48 | Supplying, fitting and fixing soap holder.(a) PTMT (Prayag or equivalent). |
| 49 | Supplying fitting & fixing tooth brush and Tumbler holder of approved make of size 140mm x 65mm (porclain) |
| 50 | Supplying fitting & fixing towel rail withtwo brackets.a) C.P. over crossii) 25 mm dia and 600 mm long. |
| 51 | Supplying, fitting and fixing bathroom shelf of approved make of size 580 mm X 150 mm (porcelain). |
| 52 | Removing sludge from septic tank, soak well etc by mathor labour including disposal of the same outside the compound as directed.(a) upto 20 users(ii) Beyond a lead of 150 meter and out side the municipal limit |
| 53 | Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia (ii) 450 mm long |
| 54 | Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps (ii) 750 mm long |
| 55 | Supplying, fitting and fixing urinal flush pipe fittings of approved brand(a) C.P. urinal flush pipe fittings range of one |
| 56 | Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L.and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size)including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C.manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections,excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials.With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia.(SAIL/TATA/RINL). |
| 57 | Clearing compound premises of shurbs, plants, jungles etc. by cutting and removing as directed (Specific permission of Engineer-in-Charge prior to execution will be necessary).(Payment to be made on area cleared). |
| 58 | (C) Supplying Heavy Duty Aluminium Handle (EBCO Type) (Natural White) |
| 59 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately)(b) 40mm X 6mm, 200mm Length |
| 60 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete.(a) With continious plate base (Hexagonal / Round Rod)(ii) 100 mm grip x 10 mm dia rod. |
| 61 | Post construction measures:- (c) Anti-termite treatment to the soil under floor with chemical emulsion by admixing chloropyrofos emulsifiable concentrate (1% concentration) with water by weight including drilling vertically 12mm. dia holes at the junction of floor and wall at 300mm. interval to reach the soil below using hand operated pressure pump to squirt chemical emulsion into the pump to squirt chemical emulsion into the holes at the rate of one litre per hole. The holes shall be sealed after operation to match with the existing floor. The entire work is to be carried out as per specification laid down in para 4.3.1.4 of code I.S.-6313 (Part-III)- 1981. |
| 62 | Supplying P.V.C. water storage tank of approved quality with closed topwith lid (Black) - Multilayer(b) 1000 litre capacity |
| 63 | Labour for punching hole in plastic water storage tank upto 50 mm dia. |
| 64 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992(A) (i) Single Socketed 3 Meter Length (b) 110 mm metre |
| 65 | B)iii) door Tee(b) 110 mm |
| 66 | x) Bend 87.5º (b) 110 mm |
| 67 | xv) Vent Cowl (b) 110 mm |
| 68 | xvi) Pipe Clip (b) 110 mm |
| 69 | xx) 125/110 P Trap with W.C. Ring 75 mm |
| 70 | xxi) 110 X 110 P Trap 75 mm |
| 71 | Supplying, fitting and fixing boiling water proof ply conforming to IS: 710-1977 bonded with phenol formaldehyde synthetic resin conforming to IS: 848-1974 of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in- charge. [excluding the cost of supporting frame work and teak wood batten/Lipping]In Ground Floor(vi) 19mm |
| 72 | (A) Wood work in posts, post plates, rafters, battens, truss members, purlins etc. fitted and fixed complete (excluding the cost of bolts, paints, but including the cost of nails, screws etc.)(The quantum should be corrected upto three decimals)(ii) Sal : Local. |
| 73 | (a) Supplying \"Godrej\" mortice lock chromium plated with latch and keys 4 levers, including fitting and fixing complete.For Door |
AI Tender Summary
Tender Timeline
Jul 22, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedAug 06, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 08, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender