Tender For Addl/Altn To Main Power House Bldg No P-62 At Milit Girinagar, Pune-25; 1 B/R PORTIONComplete removal of entire existing water proofing treatment in any position, any thickness including tarfelt, Plaster, lean concrete, gravels etc. and removing the debries out side MD land complete all as specified and directed. 2 M&L for providing PCC (1:1½:3) type A0 (using 12.5mm graded stone agg) as in padding over roof & chajja (at any respective height of bldg) with using integral water proofing compound as per mfrs instructions complete all as specified and directed. 3 M&L for 10 mm thick rendering in CM 1:4 over concrete surfacesmixed with water proofing compound @ 3% by weight of cement complete all as specified and directed.Note: Water Proofing compound shall be measured and paid for seprately as Supply Only 4 Supply only WPCcomplete all as specified and as directed. 5 M&L Acrylic emulsion polymerof acrylic single component low viscosity polymer for preventing leakages over exisitng/New surface of slab, terrace, exterior, interior wall, Chajjas etc as per following procedure :-(a) Surface & surface preparation : Remove all the loose particles, dirt & dust clean by water, wire brush & mechanical cleaning, grease & oil should be cleaned using solvents,It the surface is previously coated with tar, it should be thoroughtly scraped off.The surface should be dry before application.All the cracks and crevices in the concrete slab to be filledwith polyurethene based sealent with and including application of PU based primer complete all as specified and directed.(b) Finish paint : Apply water based polyurethenene modified dispersion (single component cold applied, non toxic, VOC complaint) in 03 coats icluding 01 coat of primer of same materials after dillution of water at 50 % or specific primer matching same material as per manufacturers complete all as specified and directed. 6 Demolition of reinforced cement concrete, (other than ground floors), shelves, chajjas, slabs and similar work carefully and matching to adjoining disturbed surfaces complete all as specified and directed. 7 Supply and fix in repairs for aluminium powder coatedpartition using ‘Jindal’ aluminium SP/ DP section or equivalent make as specified with 5mm thick tinted/plain glass, PVC rubber beading fixed with glazing clips etc complete all as specified and as directed. Sections : SP (Single partition)- 20033, DP (Double partition)- 20034,Glazing clips-4407complete all as specified and as directed. 8 Taking down chowkats or frames of wooden or steel exc 1.5 sqm & n.exc. 4 Sqm with Shutters (without taking off shutters from the frames) complete all as specified and directed. 9 Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each and removing from site complete all as specified and directed. 10 M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified, supplied and fixed size 105X60mm ccomplete all as specified and directed. 11 M&L for PCC 1:3:6 type C-0 (using 12.5mm graded stone aggregate) as in filling steel frames etc. incl necessary form work complete all as specified and directed. 12 M&L for 35 mm thickFlush shutters with lipping all around of solid core construction with block board core and ply wood face panels commercial type on both side complete all as specified and directed. 13 M&L for preparation of new/oldwooden surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 14 S&F three track sliding window with 4mm thick tinted glass in two shutter and one shutter using stainless steel wire cloth 0.36mm nominal dia & 1.18mm width aperture for mosquito proofing including good quality bearing handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of JINDAL or of equivalent make complete all as specified and directed by Engr-in-Charge and including taking down old steel windows. Series of aluminium section as per Jindal is (a) Bottom frame - 20620 (b) Top frame & vertical - 20621 (c) Handle (side) - 20606 (d) Shutter inter lock - 20724 (e) Shutter top & Bottom - 20844 (f) Glazing clips - 19352 complete all as specified and as directed. 15 Supply and fix for aluminium powder coated louvered ventilator with provision of exhaust fan using ‘Jindal” aluminium section or equivalent make as specified including glass 3mm thick ordinary quality, frosted and stainless steel wire mesh 0.36mm dia wire and 1.40mm aperture etc complete all as specified and directed. 16 S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, all as mentioned in Item No. 8095 of SSR Part-II complete all as specified and directed. 17 S&F factory made solid panel decorative PVC door shutter 30mm thick (stiles) consisting of frame made out of M.S tubes for top & bottom rails; M.S frame shall be covered with heat moulded plain colour PVC ‘C channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification Complete all as specified and as directed. 18 Taking down the complete old collapsible/ rolling shutter including all fittings and area exceeding 9.00 Sqm in each complete all as specified and as directed. 19 S & F collapsible steel gate ,side hung,consisting of channel pickets ,pivoted flat bars,top and bottom runners ,brass locking handles etc,as specified,erected in position and securing runners with holdfast and brackets complete all as specified and as directed. 20 S&F steel rolling shutters gear operated motorised motor with electric connection made of 1.25mm thick lath, without ball bearing, & with bevel gear box and crank handle as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; errected in position as indicated, complete push pull or manual type Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed. 21 Dismantling wrought iron or mild steel work of anydescription not otherwise providedfor complete all as specified and as directed. 22 M&L for non structural steel in framed work such as grills,gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe-290.Gde-E-165 complete all as specified and directed. 23 M&L for structural steel in rolled mild steel roof trusses (framed),trussed,purlin crane,gantries,rails and fastening,and heavyframing (beam,tee,anglechannel or flat sections) including distance pieces, cleats etcFe-290. Gde-E-165 complete all as specified and directed. 24 M&L for structural steel work in tubular/square/rectangular trusses ,cantileve,purlin staging including special shaped washer etc. complete using ERW or induction butt welded tubes confrming to IS 1161-1979 grade St-240 complete all as specified and directed. 25 M&L for two coats of synthetic enamel paint over a coat of red oxide on new/old steel surfaces exc. 10 cm width or girth etc. complete all as specified & directed. 26 S & F 100 mm butt hinges medium weight cold rolled mild steel and fixed completeall as specified and directed 27 S&F aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section etc length of bolt 250 mm complete all as specified and directed. 28 S&F aluminium anodised barrel tower bolts of extruded section 200 mm long. complete all as specified and directed. 29 S&F aluminium handles, anodised, cast type, of size 150 mm complete all as specified and directed. 30 S&F stainless steel chromium plated 6 Pin, 45Cm to 60Cm long hanger fixed to wall with screws complete complete all as specified and as directed. 31 Dismantling plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof covering complete all as specified and directed. 32 S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/clading to wall, fixed with self tapping screws complete all as specified and directed. 33 S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in ridges, roof covering/clading to wall, fixed with self tapping screws complete all as specified and directed. 34 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises complete all as specified and directed. 35 M & L for 25mm thk Cement concrete type B-1 1:2:4 (20mm Graded stone aggregate) as in sub base or levelling course complete all as specified and directed. 36 M&L fornon skid, ceramic tiles 7 to 8mm thick (Square/Rectangular) area of each tile exceeding 0.06sqm but not Exceeding 0.11 Sqmcoloured tiles, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete over and including 15mm thick screed bed in CM 1:6 complete all as specified & directed. 37 S&F, glazed ceramic tiles coloured 450 x 350mmx 7 mm thick in wall/dado etc, set & jointedin neat cement slurry & pointed in white or coloured cement to match renderingover 15 mm thick in CM 1:6 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces complete all as specified and directed. 38 M&LKota stone flooring 20 to 25 mm thick laid, jointed with grey cement slurry and pointed with coloured cement to match the shade of Kota stone as in floor etc including rubbing and polishing laid over and including screed bed 20mm thick in CM 1:6 complete all as specified and directed. 39 M & L for granite 18mm thick black/red colour (of any type) work (table rubbed, and polished) in staircase steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of graniteincl Screed bed or beddinglayer of mortar 20 mmthickin cm (1:6)for laying floor finishes complete all as specified and as directed. 40 Rounding edges of stone one edge, such as in steps, cooking platform, window cill and other similar situation complete all as specified and directed. 41 Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) and removing from site complete all as specified and directed. 42 M&L for 75mm thick PCC 1:3:6 type C2 using 20mm graded stone aggregate as in plinth protection complete all as specified and as directed. 43 M&L for Hardcore of gauge n exc 63mm, deposited, spread and levelled in layers in not exc 15cm thick water and rammed to a true surface complete all as specified and directed. 44 M&L cement concrete type B11:2:4(20mm graded stone aggregate) finishing cement concrete surface even and smooth using extra cement,using dewatering trimix method 150 mm thickcomplete all as specified and directed. 45 Taking down cement plaster, any description on brick, concrete or stonewalls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal ofrubbish off outside MD land complete all as specified and directed. 46 Demolition of Brickwork or stone masonary built in Cement mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed. 47 M&L precast cement concrete block masonry with solid block, type C-1,1:3:6 mix (using 20mm graded aggregate), exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed. 48 Racking out joints/pointing to random rubble or polygonal rubble uncoursed or brought up to courses buit in cement or cement lime mortar complete all as specified and as directed. 49 M&L for keyed pointing to randomor polygonal rubble uncoursed or brought upto courses in cement mortar1:4. complete all as specified and as directed . 50 M & L for Rendering 15 mm thick on stone masonry or concrete workin CM 1;6. finished even and smooth without using extra cement complete all as specified and directed. 51 M & L rendering 15mm thick on stone masonry surface or concrete surface finished even and smooth without using extra cement in cement mortar 1:4 complete all as specified and directed. 52 M&L 5 mm thick rendering inCM 1:3 onconcrete surface of ceiling, finished even and smooth using without extra cement complete all as specified and directed. 53 M&L fortwo coats of oil bound distpemper over a coat of primer on New surfaces of wall ncluding preparation of plastered surface of wall complete all as specified and as directed. 54 M&L fortwo coats of oil bound distpemper over a coat of primer on Old surfaces of wall including preparation of plastered surface of wall complete all as specified and as directed. 55 M&L forapplying two coats of oil bound distpemper over a coat of primeron new surfacesof ceiling complete all as specified and directed. 56 M&L forapplying two coats of oil bound distpemper over a coat of primeron old surfaces on old surfaces of ceiling complete all as specified and directed. 57 M&Lfor applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/Litre and UV resistance as per IS 15489:2004, Alkali & Fungal resistance exterior paint of required shed (Company Depot Tinted) with silicon additives @ 1.43 Litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 Lit/sqm over new/old surfacesincluding complete removal of existing paint by bio wash, necessary scaffolding required for painting work, safety measures etc complete all as specified and directed 58 S&F retro reflective regulatory singn board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro-reflective sheeting as approved by Engineer-in-charge. Letter, symbos, borders etc will be as per IRC-67 with required colour sheme on the boards and with the intensity grade A.The aluminium sheet to be riveted to M S frame of angel iron of size 400x400x4 mm. The board will be fixed to 1 No. 50x50mm squared post mad M S angle 50x50x4 mm, 4 m long weled to the frame with adequate anti-theft arrangement. Sheet work to be painted with two or more coats of synthetic enamel paint over and under coat (primer0 and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete all as specified and directed. 59 S & F 100 mm butt hinges medium weight cold rolled mild steel and fixed complete all as specified and directed. 60 S & F 150 mm long aluminium anodised barrel tower bolt complete all as specified and directed. 61 S & F 150 mm Handles medium weight cold rolled mild steel complete all as specified and directed. 62 S & F 20mm Gun metal globe or gate valve with iron wheel head screwed both ends to iron pipe, fixed complete all as specified and directed. 63 Taking down 15 mm bore steel water tubing and connections complete all as specified and directed. 64 Taking down 20 mm bore steel water tubing and connections complete all as specified and directed. 65 S&F for steel water tubes, 20mm bore medium grade, galvanized with all fittings and fixed complete to walls, ceiling or laid in floor, complete including taking up or down steel tubing and connections or removal to store complete all as specified & directed. 66 All as per herein above but 15mm complete all as specified & directed. 67 M&L for cutting chases, pinning in stone, concrete block walls making good to facings where required and pointing in cement mortar 1:3 to concealed water tubingand making good complete all as specified and directed. 68 S&F in repairs 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball brass valves, high pressure, with polythene float and fly- nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. 69 S & F in repairs PVC connection 45 cm long 15 mm bore with 2 Nos PTMT check nuts complete all as specified and directed. 70 S & F in repairs for vitreous china, squatting pan of Orissa pattern, size 580 mm x 440 mm, white, with P of S Trap, front or back inlet and integral foot rests any pattern, including provision of lime concrete bedding, 10 litres capacity PVC low level flushing cistern, all internal fittings, inlet, outlet pipe connections etc complete all as specified and as directed. 71 S&F in repairs vitreous china wash hand basin pedestal type, white, 550x 400mm flat back including providing CI brackets, PVC waste pipe 32mm dia, CP brass waste coupling 32mm dia etc, 15mm bore CP fancy type pillar tap complete all as specified and directed. 72 S&F in repair Vitreous china Urinal, half stall type, white with 32 mmwaste pipecomplete including providing andfixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass screws, pointing around urinal back in cement;flush pipe, grating and union for discharge pipe including CP Urinal spreader for fixing with 15 mm dia pipe complete all as specified and directed. 73 S & F stainless steel grating doom 125mm dia complete all as specified and directed. 74 S&F in repair 125 mm chromium plated shower roses with shower arm with or without swivel joints, any size including fixing to uPVC/Steel pipe complete complete all as specified and as directed. 75 M&L for 100mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete complete all as specified and as directed. 76 M&L for looking mirror 600 x 450mm beveled edge mirror of selected quality glass mounted on 6mm thick commercial plywood and fixed to wooden plugs with steel screw, complete all as specified and directed. 77 S&F in repairs Bib taps fancy type ( short /long body )chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule all complete as specified and as directed. 78 S&F in repairfancy type, chromium plated angular stop cock fixed with wall flange for 15mm bore of pipe complete all as specified and as directed. 79 S&F in repairs 60 cm long brass CPtubular towel rail 20-mm diaD type complete all as specified and directed. 80 S & Fin repairs soap dish chromium plated of size 100 x 100 mm any type, chromium plated brass screws complete all as specified and directed. 81 S&F factory made 50mm thick 900 x 600mm manhole cover with additional frame for fixing, of precast RCC 1:2:4 type B1 (using 20mm graded stone aggregate) finished the surface even and fair including reinforcement as per manufacturers design and set in CM 1:4 and handles including demolition of old existing RCC cover (Reinforcement required to cut as facilitate to domolition) of any description and in any position complete all as specified and directed. 82 Cutting into existing manholes for connecting new drains internal dia of pipe 200mm making good to pipe & toor finished and reforming benching as required. 3/4 section in cement concrete (1:2:4) type B-1, smoothcutting out existing benching for forming branch channel (1/2) rendering complete all as specified and as directed. 83 M&L for provided reinforced cement concrete pipe 150mm bore class NP-2 with collars laid and jointed with cementcomplete all as specified and directed. 84 M&L for concrete bed to drain pipes including pipes under and haunching againstthe sides of pipes after they are laid and tested in cement concrete 1:4:8 type D-2 for 150mm dia pipe complete all as specified and directed. 85 M&L for cement concrete 1:3:6 type C2(using 40mm Graded stone aggregate) as in surface channels and drains including necessary form work for sauccer drain complete all as specified and directed. 86 Extra for forming fair finished drain or channel 45cm inner girth in cement concrete, using extra cement, incl forms, moulds, mitred /stopped ends etc complete all as specified and directed. 87 S&F in repairsPVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to wall of size 110mm bore complete all as specified and directed. 88 S&F PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or in floor of 75mm bore complete all as specified and directed. 89 S&F in repairs PVC (SWR) pipes, single socketed in any length with rubber ring joints, joints fixed to wall of 75mm bore complete all as specified and directed. 90 S&F PVC (SWR) junction, (Single Tee) equal or unequal 110mm bore complete all as specified and directed. 91 S&F PVC (SWR) junction, (Single Tee) equal or unequal 75mm bore complete all as specified and directed. 92 S&F PVC (SWR) bends any radius 110 mm bore complete all as specified and directed. 93 S&F PVC (SWR) bends any radius 75 mm bore with trap door complete all as specified and directed. 94 S & F PVC (SWR) vent cowl 110mm Bore complete all as specified and directed. 95 S & F PVC (SWR) vent cowl 75mm Bore complete all as specified and directed. 96 S&F PVC (SWR) gully traps 125/100 setting and jointed in cement solvent complete all as specified and directed. 97 E/M PORTIONTaking down carefully aluminum/copper point wiring (light fan, socket or power) complete incl fittings and fixtures such as switches, sockets, light fittings, ceiling rose, pendants, lamp holders, shade conical, regulators and separating serviceable fittings for reuse in the same work and removing unserviceable fittings and fixtures with wiring cable, battons, wooden boards etc from site and making good disturbed surfaces of walls, floors, ceilingetc complete all as specified and directed. 98 Taking down sub main wiring complete including fitting and fixtures, removing materials for taking credit and making good disturbed surfaces of walls, floors, roof etc, complete all as specified and directed. 99 Taking down carefully unserviceable DBs any type/size With MCCBs/MCBs//Isolator etc and disconnecting and making good disturbed surfaces complete all as specified and directed. 100 M&L for point wiring with 1.5 sqmm size (nominal area)FRLSH PVC insulated unsheathed1100 Volts grade cable stranded copper conductor single coreconcealed in wall through PVC Conduit and conduit accessories and partly surface on ceilling, beam and columns and accessories of size 20/25mm complete with modular box and cover plate with frame as per requirement for fitting mounting switch/sockets regulators with 1.5 sqmm PVC insulated copper conductor earth wire and connected to earth wire and connected to earth dolly for light point controlled by one switch complete all as specified and directed. (a) One light point/fanpoint/exhaust fan point controlled by one way switch. 101 (b) One 3 pin switch socket outlet point 5 Amps on independent board. 102 (c) One 3 pin switch socket outlet point 5 Amps on same board with other switch. 103 All as per item No 4 above but for 3 pin socket outlet 15 Amp independent with cable 4 sqmm unsheathed stranded 1100 Volts grade complete with 4 sqmm PVC insulated earth wire and connecting to earth dolly complete all as specified and directed. 104 Supply & fix modular switch 1 way 6A, 1 module complete all as specified and directed. 105 Supply & fix modular switch1 way 16A, 1 module complete all as specified and directed. 106 Supply & fixmodular socketout let 6A 2/3 on combined 2 module complete all as specified and directed. 107 Supply & fix modular socket out let 6A/16A-2/3 pin combined 2 module complete all as specified and directed. 108 Supply & fix Ceiling rose surface backlite 65x50mm 3 terminals complete all as specified and directed. 109 Supply & fix of LED Tube light luminaires, 20-22 watts, lumen output not lessthan 2000 (4 feet), made of anodised extruded aluminium housng, with high transmissivity diffuser, high lumen output, with suitable integrated electronic driver, and operated in single phase, 230 volts, 50HZ, all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable offrom connector and ceiling rose, complete all as specified and directed. 110 Supply and fix LED tube light fittings Al housing mirror type with high output diffuser 2 feet,10 Watt 220V ACincluding connecting up with three core flexible copper conductorcomplete all as specified and directed. 111 Taking down ceiling fan any type/ size from hook and dismantling cable and blades and bring in to contractor store for repair and hanging ceiling fan in position after repair, greasing etc. with existing flexible copper cable, new rewinding of fan, painting and spare parts required are deemed to be included in the quoted rate complete all as specified and directed. 112 Taking down exhaust fan any type/ size from hook and dismantling cable and blades and bring in to contractor store for repair and hanging ceiling fan in position after repair, greasing etc. with existing flexible copper cable, new rewinding of fan, painting and spare parts required are deemed to be included in the quoted rate complete all as specified and directed. 113 M&L for sheet metal enclosure for Ekinox TPN DB-VTPN 4 way 415 V, double door , 250 A copper bus bar, IP 43, including 125 Amp MCCB as incomer as flush mounted complete all as specified and as directed. 114 Supply & fix sheet metal enclosure distribution board SPN, 8 ways 240 volts, with suitable capacityamps rated bus bar, with IP 43 protection and double door, suitable for mounting MCBs complete all as specified and directed. 115 Supply & fix sheet metal enclosure distribution board SPN, 4 ways 240 volts, with suitable capacityamps rated bus bar, with IP 43 protection and double door, suitable for mounting MCBs complete all as specified and directed. 116 Supply & fix of MCB single pole and neutral, 240 volts, 6 to 40 Ampere, rupturing capacity 10 KA, ‘C’ series complete all as specified and directed. 117 Supply & fix of MCB single pole, 240 volts, 6 to 40 Ampere, rupturing capacity 10 KA, ‘C’ series complete all as specified and directed. 118 M & L for submain wiring alongwith earth wire with the following sizes of FRLSHPVC insulatedcopper conductor single core cable, multistranded Cutting chases, pinning in making good to facings Concealedand including suitable size ofConcealed conduit with itsall accessories all as specified and directed by Engr-in -charge for the following: (a) 2x6 sq mm and 1x6 sq mm as earth wire 119 All as per herein above but for 2x2.5 sq mm and 1x2.5 sq mm as earth wire 120 M&L for earthing with galvanized steel earth plate 60cm x 60cmx 6.3mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with the top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanized earth strip size 25 x 4 mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel and earth plate surrounded by packet layers of coal dust and common salt 15 cm thick allaround top and bottom all as shown in electrical plate No 3 connected to earthing test point all as specified or indicated including necessary excavation and earth work PCC (1:3:6) type C1 earth pit, cast iron pit cover, funnel with water pipe 20mm dia medium grade, 1.5mtr long and 20mm bore light grade from earth plate to test point or main switch/DB as protection pipe and testing on completion including excavation earth work and disposal of surplus soils complete all as specified and directed. 121 Supply and fix LED Flood light 70 W IP 66 230VAC outdoor type with thermal management in multiple optics and equipped with IP 66 protection with impact and corrision resistant complete with all necessary fittings like angle, clamp, screw, nuts etc complete all as specified and directed. 122 Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor includingClip, cable rack proper lay over the surface/floor. (a)25 sqmm 4 core . 123 Supply and laying 50mm HDPE DWC pipe complete all as specified and as directed 124 Taking up or down steel tubing & connectionsin trenches, wall / floor including cleaningfor removal to store of size:-25 mm bore pipe 125 All as per herein above but for 20 mm bore pipe 126 All as per herein abovebut for 15 mm bore pipe 127 Supply and laying tubes, Galvanised, medium grade, with all fittings and fixed to walls, ceiling or laying in floors, all as specified for following size:-25 mm bore pipe 128 All as per herein abovebut for 20 mm bore pipe 129 All as per herein above but for 15 mm bore pipe 130 Supply and fixing ofGun metal gate valves with iron wheel head, screwed both ends for iron pipes complete, size of GM gate valve 25mm. 131 All as per here in above but size of GM gate valve 20mm. 132 All as per here in above but size of GM gate valve 15mm. 133 Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth and getting out in soft loose soil complete all as required and directed by Eng-in-charge. 134 Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm complete all as required and directed by Eng-in-charge. 135 Removing excavated material not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as required and directed by Eng-in-charge.
