|
| 1 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 2 | M & L for 25 mm thick, plain cement concrete 1:2:4,type B-0 (using 12.5 mm graded stone aggregate)as in sub-base of flooring, etc and finished the surface even and rough complete all as specified and directed. |
| 3 | M&L for Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Rectangular/ Square), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm (1st quality as approved) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. |
| 4 | M&L for Non Skid colouredceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchfixed over and including 15mm thick screed bed in CM 1:6 complete all as specified and as dircted |
| 5 | M&L for Coloured Glazed Ceramic Tiles 300x200x7.0mm thick (1st quality as approved) as in Vertical Surfaces i.e. Dado, Skirting, etc., set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile fixing over and including Screed or Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. |
| 6 | Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 7 | S&F Steel work in (sqare/ Rectangle) tubular trusses, rafter, purlins, post etcincluding special shaped washer etc.complete using ERW or induction butt welded tubes conforming to Fe- 290 (Gde E- 165) complete all as specified and directed. |
| 8 | M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zine chrome primer complete all as specified and directed. |
| 9 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness including nainital or similar pattern roof coverings any thickness complete all as specified and as directed. |
| 10 | S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 11 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/roof covering/cladding to wall, fixed with self tapping screws as specifiedspecified and as directed. |
| 12 | Dismantling of wall and ceiling boards (fibre, pulp, insulation) or insulation boards, bonded wool, blanket slab incl aluminium grid frame work complete all as specified and as directed |
| 13 | S&F Hangers 4mm dia G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long sizeof grid 605 x 605mm complete all as specified and as directed |
| 14 | S&F anodised aluminium snap grid frame work for false ceiling of size of grid 605x605 mm. complete all as specified and as directed. |
| 15 | S&F HSPC Non-Asbestos Fibre Cement Building Boards 4.0mm thick in Ceiling, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to Aluminum Snap Grid Frame Work with Screws, complete all as specified and as directed. |
| 16 | Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 17 | M&L for 75mm thick plain Cement Concrete 1:3:6 (40mm graded stone aggregate) as in Plinth Protection, etc., laid in alternate panels, finished Concrete Surfaces even and Smooth without using extra Cement, complete all as specified and as directed. |
| 18 | Taking down Shutter of any description,exc 1.00 sqm but not exc. 2.00 Sqm Each, complete all as specified and as directed. |
| 19 | S & F Aluminium anodised sections (minimum 50 micron) of approved colour as in door, window, ventilator frames, partitions with one or more rebates and door, windows shutters sliding type shutter including provision of necessary jointing cleats, glazing clips, neoprene rubber packing, powder coated aluminium snap beading, screws inclding provision of suitable size of powder coated aluminium fittings such as locking arangements, handles, stainless steel fiction hinges and tower bolts etc including fixing only glass panels/particle board panels/wire gauge/aluminium grill etc complete all as specified and directed. Note : The size of aluminium sections shall be all as specified in relevant IS Code and MES Schedule Part-I |
| 20 | S & F in repair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 21 | Material & labour for 3 mm thick sheet glass ordinary quality and glazing with oil putty / beads in square, area exc 0.5 Sqm in each pane complete all as specified and directed. |
| 22 | S&F Factory made solid panel PVC Door Shutter 30mm thick (Style) consisting of Frame made out of Mild Steel Tubes for Top & Bottom Rails, Mild SteelFrame shall be covered with Heat Moulded Plain Color PVC ‘C’ Channel having a PVC Strip of 20mm width stuck inside with Solvent Cement for Stiles & Plain color PVC Sheets for Top Rail, Lock Rail & Bottom Rail on Either Side & Gap insert for Top Rail & Bottom Rail, Paneling of Plain Color PVC sheet to be fitted in the Mild Steel Frame, welded/sealed to the Stiles & Rails with suitable PVC Sheet Beading & jointed together with Solvent Cement, complete all as specified and as directed.NOTE : Builders Hardware will be Measured and Paid seperately under appropriate Items. |
| 23 | S&F Aluminium anodised Barrel Tower Bolt, 125mm long (as approved), Extruded Section, complete all as specified and as directed. |
| 24 | S&F Aluminium alloy, anodised, Sliding Door Bolt 250mm long with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed. |
| 25 | S&F Stainless Steel Butt Hinge 75mm in size (as approved), complete all as specified and as directed. |
| 26 | S&F Aluminium Handle 125mm in size (as approved), anodised, Cast type, complete all as specified and as directed. |
| 27 | Taking down ,Chowkhats or frames with shutters (without taking off shutters from the frames) exc of any descriptionexc1.5 sq. m but n exc 4 sq. m Each, complete all as specified and as directed. |
| 28 | S & F for Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 29 | S & F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining leats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified |
| 30 | S&F Aluminium anodised Barrel Tower Bolt, 150mm long (as approved), Extruded Section, complete all as specified and as directed. |
| 31 | S&F Aluminium alloy, anodised, Sliding Door Bolt 300mm long with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed. |
| 32 | S & F Sheet glass 5.5 mm thick, ordinary quality and glazing with oil putty or wooden beadsexceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed. |
| 33 | S & F 4 Lever Mild Steel Mortice lock, vertical type, size 100 mm complete all as specified and directed. |
| 34 | S&F Door Closer Aluminium (Die-cast) Body, Hydraulically Regulated, Designation No. 3, Universal type, suitable for Door Shutters of 851mm to 1000mm in width and of weight between 61.00 KG to 80.00 KG and Fixed-in-repairs, complete all as specified and as directed. |
| 35 | S&F Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with PVC (SWR) ‘P’ or ‘S’ Trap, and Fixing Bolts and Making Good to Floor/ Distrubed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed. |
| 36 | S&F Vitreous China White Wash Hand Basin with pedestal of size 550x400mm, White (Flat Back) including Brass Chromium plated Waste Fitting 32mm bore (dia), PVC Waste Pipe 32mm/40mm and a Pair of Cast Iron Brackets or Erecting Stand duly Painted (but excluding Taps, Chain, Plug & Porcelain Stopper), cutting and pinning in ends, making good disturbed surfaces in cement mortar 1:3, complete all as specified and as directed. |
| 37 | S&F Vitreous china white Urinal,half stall type (excluding Flushing Cistern, Flush Pipe and Waste Pipe) including providing and fixing plugs, bedding urinals against wall in Cement Mortar 1:2, securing Urinal to Plug with and including 60mm long Brass Chromium plated Screws, Pointing around Urinal back in Cement Mortar 1:3, fixing Urinal Spreder of Brass Chromium plated, Flush Pipe, Grating and Union for Discharge Pipe (but Exclusive of fixing Supply Pipe to Flushing Cistern, Trap and Waste Pipe) and Fixed-in-repairs, complete all as specified and as directed. |
| 38 | S & Fin repairs 600mmx450 mm bevellled edgemirrorofselectedqualityglasss, mountedon 6 mm thick commercialplywoodandfixedtowoodenplugswithchormiumplatedbrass screwsandcup washers complete all as specified. |
| 39 | S&F PVC flushing cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type, Dual Flush ISI Marked (IS:7231) with Inlet, Ball Valve, Float and Handle, a Pair of Cast Iron Brackets Erecting Stand duly Painted, including PVC Flush Pipe 32mm dia with PVC Long Bend, Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed. |
| 40 | S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and Fixed-in-repairs, complete all as specified and as directed. |
| 41 | S&F Pillar Tap 15mm bore (dia), Cast Copper alloy with Capstan Heads, Chromium Plated, Fancy type, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed. |
| 42 | Supply and fix in repairs stop / Angle valvescast copper alloy, screwed down high pressure with capastan headscrewed both ends 15 mm bore fancy type chromium plated with long shank and cup suitablecomplete all as specified and as directed. |
| 43 | S &FPVC connection15 mmboreand45 to 60 cmlongall asspecifiedandasdirtected. |
| 44 | Taking down steel tubing 15 mm bore and connections and removal to store or keep separately for reuse complete all as directed. |
| 45 | S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed. |
| 46 | Re-fixing Old Steel Tubing 15mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from Item No. 44 here-in-before) in New or Old Position (Walls, Ceiling, Floors, etc.) including Cleaning both Inner and Outer Surfaces of Pipes by using Wire Brush before fixing/ laying including Provision of New GI Fittings/ Connections (as required ordered at Sites), complete all as specified and as directed. |
| 47 | Taking down steel tubing 20 mm bore and connections and removal to store or keep separately for reuse complete all as directed. |
| 48 | S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed. |
| 49 | Re-fixing old steel tubing 20mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from Item No. 47 here-in-before) in New or Old Position (Walls, Ceiling, Floors, etc.) including Cleaning both Inner and Outer Surfaces of Pipes by using Wire Brush before fixing/ laying including Provision of New GI Fittings/ Connections (as required ordered at Sites), complete all as specified and as directed. |
| 50 | Dismantling existing water storagetanks exc 500 litres but n.exc 1000 litres capacity and removal from site complete all as specified. |
| 51 | 1000 litres capacilty, roational moulded polythylene water storage tank double layered (cylindrical vertical with closed top) hoisted and fixed in position including GI tank nipple & with union (two Nos each) fittings and making necessary connections to make the tank functional complete all as specified and directed. |
| 52 | S&F Gun metal globe or gate valves with iron wheel head, screwed both 20 mm bore in repairs complete all as directed.. |
| 53 | S&F PTMT Ball Valve 20mm bore (dia), having weight not less than 210 Grams, high pressure with Epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed. |
| 54 | S&F Toitet Paper Holder, Vitreous China, Coloured, Box type of approved Size with Brass Chromoum Plated with Rod to hold Paper Roll, fixed to Walls with Brass Chromium plated Screws and Fixed-in-repairs, complete all as specified and as directed |
| 55 | S&F in repair Hand Shower (Health Faucet) mild steel chromium plated suitable for 15mm dia pipe with 1.25 Metre in long flexible tube and ABS wall hook, complete all as specified and as directed. |
| 56 | S&F in repairTubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (One Pair), fixing to Walls with and including Chromium plated Brass Screws and Wooden/ Plastic Cleats, complete all as specified and as directed. |
| 57 | S&F in repairCast Iron Floor Trap, Diameter of Outlet in 100mm, Plain with Gratingincluding Jointing with Waste Pipe, Set in Cement Concrete 1:2:4 (20mm graded Aggregate) , complete all as specified and as directed. |
| 58 | S&F PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC/Rubber Ring Joints, with or without Ears, laid on Floors or fixing to Walls, etc. including Taking down/ out Unserviceable Pipe of any description, complete all as specified and as directed. |
| 59 | S&F PVC (SWR) 110mm bore (dia) Bends (any radius), Diminishing Pieces or Tapers (larger bore measured) Fittings, jointing with Solvent Cement and Fixing-in-repairs, complete all as specified and as directed. |
| 60 | S&F PVC (SWR) 110mm bore (dia) Junction, Single (Single T) Equal or Unequal, etc., jointing with Solvent Cement and Fixing-in-repairs, complete all as specified and as directed. |
| 61 | S&F PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC/Rubber Ring Joints, with or without Ears, laid on Floors or fixing to Walls, etc. including Taking down/ out Unserviceable Pipe of any description, complete all as specified and as directed. |
| 62 | S&F PVC (SWR) 75mm bore (dia) Bends (any radius), Diminishing Pieces or Tapers (larger bore measured) Fittings, jointing with Solvent Cement and Fixing-in-repairs, complete all as specified and as directed. |
| 63 | S&F in repairPVC (SWR) 75mm bore (dia) Junction, Single (Single T) Equal or Unequal, etc., jointing with Solvent Cement, complete all as specified and as directed. |
| 64 | S&F in repairPVC (SWR) Vent Cowl 110mm bore (dia), jointing with Solvent Cement , complete all as specified and as directed. |
| 65 | S&F in repair Stainless Steel wall Hangers fixed in wall with screwed or nails setting , complete all as specified and as directed. |
| 66 | S&F in repairStainless Steel Grating 100mm in dia (as approved) with Waste Hole, setting, complete all as specified and as directed. |
| 67 | Supply & fix 25mm dia MS fancy type vista pattern curtain rod of approved finish of superior quality including fancy type knobs at both ends, bracket for supports & rings etc complete all as specified and directed. |
| 68 | M & L for Mild steelframed work such as Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 69 | Excavating in post holes in soft/loose soil (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, |
| 70 | M&L for PCC 1:3:6 Type C-2 using 40mm graded stone aggregate as in in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars,boundary pillars and posts (including caps and bases) etc complete all as specified and directed. |
| 71 | Demolition of brick work or stone masonry or PCC block manonry built in cement mortar including all quoins, pillars, arches etc. |
| 72 | M&L precast cement concrete block masonry with solid block, type C-1,1:3:6 mix( using 20mm graded aggregate ), exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed. |
| 73 | Taking down cement plaster of any description including racking out joints, hacking for keys , scrubing down with water etc complete all as specified. |
| 74 | M&L Rendering (Internal) 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without Using Extra Cement, complete all as specified and as directed. |
| 75 | M&L rendering 15mm thick on fair faces of brick work or concrete surfaces in cm 1:4 finished even and smooth without using extra cement, complete all as specified & directed |
| 76 | Supply only integral water proofing compound (ISI marked) complete all as specified and directed. |
| 77 | M&L for preparation of new plastered surfaces of walls and applying two coat of cement based paint overa coat of alkal resistant primer complete all as specified & directed |
| 78 | M&L Preparing New Plastered Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion (as approved) over a Coat of Chalk Whitening (Priming Coat), complete all as specified and as directed. |
| 79 | Demolition of reinforced (reinforcement cut as required to facilitate demolition) cement concrete in ground floors and paving not exceeding 15 cm thickness( below or above ground level) all as directed. |
| 80 | M&L for precast cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) setin cement mortar (1:6) work for landings, cover slabs, manholes, chajjas, water troughs, manger shleves and similar articles with plain faces complete all as specified and as directed |
| 81 | M&L mild steel TMT bars 10mm dia and over cut to length bent shape as required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-S complete all as specified and as directed. |
| 82 | M&L for TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking bending hooking ends spirally and binding as in stirrups, spacers and binders etc complete all as specified & directed. |
| 83 | M&L for preparation of old steel surface of any description over 10 cm in width or girth,not otherwise described and applying one coat of synthetic enamel paint all as specified and directed. |
| 84 | M&L for preparation of old painted surface of cement bonded particle, board/asbestos cemet surface of any description over 10 cm girth or width , not otherwise desribed and applying one coat of Synthetic enamel paint on walls and ceiling surface complete all as directed. |
| 85 | Surface dressing not exc 15 cm deep in soft/loose soilcomplete all as specified and as directed. |
| 86 | Excavation in trenches , n exc 1.5 m wide and n exc 1.5 m in depth; for foundation,pipe laying etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and, in soft/loose soil and getting outcomplete all as specified and as directed. |
| 87 | M&L PCC 1:4:8 type D-2 (using 40 mm graded stone agg) as in foundation ,filling mass complete all as specified & directed. |
| 88 | M&L for RCC Nominal mix M-25 using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, bases for columns, etc. basement slabs, under reamed piles and mass concretecomplete all as specified and as directed. |
| 89 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or batter complete all as specified & directed. |
| 90 | M&L for cement concrete 1:2:4 Type B1 (using 20mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed. |
| 91 | Formwork to sides and soffits of floor or roof beams, lintel bands, beam haunchings, girders, lintels, cantilevers etc complete all as specified & directed. |
| 92 | Returning filling in including spreading leveling, watering and well ramming in layers not exc 25 cm in soft/loose soi lcomplete all as specified & directed. |
| 93 | Removing excavated material n exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified & directed. |
| 94 | M&L for sand filling under floors or in foundations, spreading and levelling etc complete all as specified. |
| 95 | M & L hardcore of broken stone boulsers of gauge n.exc.63mm,deposited,spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface complete all as specified & directed. |
| 96 | M & L for 100mm thick PCC 1:4:8 type D-2 as in sub base, Floors, Paving, finished even and fair complete all as specified complete all as specified & directed. |
| 97 | S&F Solid PVC Door Frame of Size 50x47mm made out of 5.0mm thick plain colour PVC Sheet reinforced with Mild Steel Square Tube and fixing in Opening as per Specification and Drawing of MES Schedule, complete all as specified and as directed. |
| 98 | M & L for RCC M -25 ( Using 20mm graded aggregate ) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves |
| 99 | Use & waste Formwork flate rough finished surface of concrete to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick |
| 100 | M & L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete |
| 101 | M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed. |
| 102 | S & F of 12mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces; fixed with screws to timber frame work etc and all as specified and directed |
| 103 | M&Lfor preparation of new painted surfaces of wood or wood based surfaces of any description exc 10 cmwidth or girth and applyingtwo coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 104 | S&F Flush Shutter 30mm thick, Solid Core Construction, with Block Board Core and Plywood Face Panels, Commercial type on Both Sides including Teakwood Lipping 6.0mm thick, fixed with Nails, complete all as specified and as directed. |
| 105 | S&F Stainless Steel Butt Hinge 100mm in Size, complete all as specified and as directed. |
| 106 | S&F Aluminium Handle 150mm, Cast type, anodised, complete all as specified and as directed. |
| 107 | S&F Floor Door Stopper having Overall length of Cover Plate 140mm of Aluminium Alloy Body and Tongue, anodised, with Hard Drawn Steel Spring, fixed in Floor and Fixing-in-repairs, complete all as specified and as directed. |
| 108 | M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 30mm thick, Divided into Squares, with plain, chamfered or rounded, mitred and rebated Sash Bars to receive Gauge/Glass, any numbers, Sizes of Members of Shutter as specified in SSR Part-I, Section 8, Clause 8.24(b) and fitted to Chowkat, complete all as specified and as directed. |
| 109 | S & Fin1200mmx600 mm bevellled edge Looking mirrorofselectedqualityglasss, mountedon 6 mm thick commercialplywoodandfixedtowoodenplugswithchormiumplatedbrass screwsandcup washers complete all as specified. |
| 110 | M & L for Silicon Gel filling to leaked Holes through pressure Gun of Old PGI /CGI or Pre painted Galvalume sheet complete all as specified and directed |
| 111 | Taking down copper/aluminium point wiring (light fan,socket or power) complete, incl fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc all as specified and directed. |
| 112 | M & L for Dismantling house service bracket any type complete all as specified and directed, |
| 113 | M & L for Dismantling MCB DB any type complete all as specified and directed, |
| 114 | M & L for point wiring with 1.5 Sqmm FRLS PVC insulated unsheathed 1100 Volts grade multi stranded copper conductorin PVC casing capping (ISI Marked) (Approx size 20/25/40mm width) along with all fitting/ fixtures as Tee, Bend Elbow socket, Saddles etc. complete with PVC board/ box suitable size / shaped for and accommodating switches sockets, regulatorsin white / ivory/ off white colour and with 1.50 Sqmm FRLS PVC insulated copper conductor strandedas earth wire connecting to earth dolly for one light/ fan/bell point controlled by one way switch 5 Amps complete all as specified and directed, |
| 115 | All as per item No. 114 here-in-before but one 3/5 pin socket 5 Amps on thesame board with other switches with cables 1.5 sqmm size. |
| 116 | All as per item No. 114 here-in-before, but one 3/5 pin socket 5 Amps, independent, with cables 1.5 sqmm size. |
| 117 | All as per item No 114 above but for 3/5 pin socket outlet 5/15 Amps, independent with 2.50 Sqmm single core PVC insulated unsheathed 1100 Volts grade multi stranded copper conductor FRLS complete with 2.50 Sqmm stranded copper conductor PVC insulated unsheathed earth wire and connecting to earth dolly complete all as specified and directed. |
| 118 | S&F Modular switch, one way, 6 A, 1 Module complete all as specified and as directed. |
| 119 | S&F Modular socket outlet, 6 Amps, 2 /3 pin combined, 2 Module complete all as specified and as directed. |
| 120 | S&F Modular switch, one way, 16 A, 1 Module complete all as specified and as directed. |
| 121 | S&F Modular socket outlet multipupose, 16/6 Amps, 3 pin combined, 2 Module complete all as specified and as directed. |
| 122 | S&F Modular fan regulator step type, 120 Watt, 2 Module complete all as specified and directed. |
| 123 | S&F Modular white colour plate with frame 1 module complete all as specified and directed. |
| 124 | S&F Modular white colour plate with frame 2 module complete all as specified and directed. |
| 125 | S&F Modular white colour plate with frame 3 module complete all as specified and directed. |
| 126 | S&F Modular white colour plate with frame 6 module complete all as specified and directed. |
| 127 | S&F Modular white colour plate with frame 8 module complete all as specified and directed. |
| 128 | S&F Modular metal flush box white colour coated 1/2 module complete all as specified and directed. |
| 129 | S&F Modular metal flush box white colour coated 3 module complete all as specified and directed. |
| 130 | S&F Modular metal flush box white colour coated6 module complete all as specified and directed. |
| 131 | S&F Modular metal flush box white colour coated8 module complete all as specified and directed. |
| 132 | S&F Lamp Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed. |
| 133 | S & F Ceiling rose surface type bakelite 65x50 mm two to three terminal suitable for 230 Volts AC 6 Amps, complete all as specified and as directed. |
| 134 | M& L for Wiring for submain wiring alongwith with the 2 X 4 Sqmm + 1 x 4 Sqmm earth wire of FR PVC insulated copper conductor single core cable in PVC casing caping etc. complete all as specified and directed. |
| 135 | M& L for Wiring for submain wiring alongwith with the 2 X 6 Sqmm + 1 x 6 Sqmm earth wire of FR PVC insulated copper conductor single core cable in PVC casing caping etc. complete all as specified and directed. |
| 136 | S & F LED luminaire 600 mm x 600 mm, 35/36 Watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor energy saving recessed LED flat panel 35/36 watt (3000k to6000k) cases of suitable size complete all as specified and directed. |
| 137 | S & FLED tubeTube lights fitting 20 watt, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 138 | Supply and fixing LED light fitting mirror typewith high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cablecomplete all as specified and directed. |
| 139 | S&F LED bulb 9 watts, 230 volt complete all as specified and directed. |
| 140 | S & F LED light fitting 9/ 10 Watt Bulk headluminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 141 | Taking down Wall fan/ceiling fan/Ex fan, ceiling cable end, dismantling and removing fan blades to stores complete all as specified and directed. |
| 142 | S & F BLDC ceiling fan 1200 mm sweep, 230 Volts AC, Min air delivery 210 CFM with service value 6.00 BEE, 5 star rated complete with blades, down rods, electronic regulator stepped type complete all as specified and directed. |
| 143 | S & F Exhaust fan, steel body with louverd, 300 mm sweep , 1200 RPM, AC ,240 volts complete all as specified and directed. |
| 144 | S & F MCB distribution board, SPN 8 way, 240 Volts AC, double door type of sheet steel phosphotised powder painted with 200 Amps,neutral bars, earth bar complete all as specified and directed. |
| 145 | Supply and fix MCB single pole 240 volts, 6 to 32 amps, 50HZ, 10 KA. , ‘C’ series all as specified and directed. |
| 146 | Supply and fixMCB single pole and neutral, 240 volts, 40 to 63 amps breaking capacity 10KA, ‘C’ Series. etc , complete all as specified and directed. |
| 147 | Supply and laying or fixing or passing through pipe, 1100voltsgrade heavy dutycablewith PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tapeandoverall PVC sheathed 10 sq mm nominal cross section 2 core in service connections complete all as specified and directed. |
| 148 | M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to earth lead wire of GI wire 4mm dia by means of nuts/bolts and washers, check nuts of galvanized iron or steel all as specified or indicated including testing on completion complete all as specified and directed. |
| 149 | M & L for Cutting cast iron/ductile iron pipes of 100mm dia in position for insertion of new tees, branches, etc.complete all as specified and directed. |
| 150 | M&L for ductile iron fittings upto 150mm dia i.e. Bend (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.)MJ collar,Tee pieces single branch. \"Y\" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs complete all as specified and directed. |
| 151 | Supplying & laying in trenches 50mm outer dia3- layer PP-R Polypropylene random copolymer) pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings . complete all as specified and directed. |
| 152 | Supplying & laying in trencies 20 mm outer dia3- layer PP-R Polypropylene random copolymer) pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings.complete all as specified and directed. |
| 153 | Supplying & laying in trenches/fixed to walls,ceilings or in floors etc25 mm outer dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain polypropylene random fittings fixed complete all as specified and directed |
| 154 | S&F PP-R Gate valves (brass insert) of size 50mm outer diameter as per requirement of the site complete all as specified and directed |
| 155 | S&F PP-R Ball valves (brass insert) of size 25mm outer diameter as per requirement of the site complete all as specified and directed |
| 156 | S&F Bib taps 20 mm dia, fancy type, cast copper alloy with crutch orbutterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed |
| 157 | M & L for construction of brick masonry valve pit of size 100 cm x 100 cm x 90 cm (internal dimension) one brick thick wall in CM 1:4 on 100mm thick PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in foundation, 15mm thick rendering in cement mortar (1:4) internally, externally up to 15cm below GL, providing valve pit cover made out of 3mm thick MS sheet duly welded with provision of hinges, handle and locking arrangement including 40 x 40 x 5mm angle iron frame fixed on top of valve pit by means of hold fast 150mm long, embedded in PCC block 1:2:4 type B-1 (20mm graded aggregate) of size 230 X 200 X 100mm, applying two coats of anti-corrosive paint over a coat of red oxide, zinc chrome primer after preparation of steel & iron surfaces including necessary excavation &earth work in soft/loose soil and demolition of existing one complete as specified and directed. |
