Tender For Construction Of Riico Shahpura 33/11Kv Gss Along With Associated 33Kv And 11Kv Line Works In Shahpura Sub-Division Of Ajmer Discom - 1 Construction of 33/11KV GSS 2 Levelling of ground 3 Levelling of ground up to 30 cm.depth. with tractor and T&P required as per condition of ground including removal of rubbish plantsfrom ground & marking of boundary with lime powder.(Including alllead & lifting) 4 Levelling of ground above 30 cm.to 90 CM.depth. with tractor and T&P required as per condition of ground including removal of rubbish plantsfrom ground & marking of boundary with lime powder.(Including alllead & lifting) 5 Trimming of tree branches/plants and preparing route approchases for proposed line. 6 Excavation of pit in ordinary rock which does not require blasting to erect various supports and stay sets including stacking of excavated muck from the edge of excavation/pit. 7 9 Mtr/ 1.2mx0.6mx1.50 m deep 8 (C)Stay set/Depth of pit 9 8x 3/4 -0.75x0.5x1.6 m 10 6x 5/8 -0.75x0.5x1.35 m 11 Excavation of pit in Hard rock ( Where blasting is required)to erect various supports and stay sets including stacking of excavated muckfrom the edge of excavation/pit. 12 9 Mtr/ 1.2mx0.6mx1.50 m deep 13 (C)Stay set/Depth of pit 14 8x 3/4 -0.75x0.5x1.6 m 15 6x 5/8 -0.75x0.5x1.35 m 16 Earth workexcavation and foundation of platfrom of transformers and brakers including dressing of sides and ramming of bottoms .Liftup to 1.5 Meter includingtaking out the excavated soil and depositing and refilling of jhiri, watering and ramming and disposal of surplus excavated soil as directed with in a lead of 50 Meter. 17 Hard/dense soil 18 Hard soil mixed with boulders 19 Providing and laying cement concrete including compaction etc, complete using stone aggregate 40 mm nominal size (hand broken) in foundation plinth excluding the cost of shuttering using 1 cement : 5 sand : 10 aggregate mix.Note :1. The rates are all lead of cement, lime, ballast, sand, surkhi and grit etc. at site of work.2. For all concrete work coarse sand shall be used no extrawill be paid .3. Concrete mix prepared by power driven mechanical mixer shall be used .4. Under exceptional coditions, where mechanical mixer and vibrator are not used (with the approval of Engineer Incharge reduced by 3% for mechanical mixer and 2% for Vibrator.5. Thickness of the cement concrete should not exceeed 100 mm. 20 Plaster on new surface on walls in cement, sand mortar 1:6 including racking of joint etc. complete fine finsh 25 mm thick.Note :1. The rates for complete work including racking of joints, curing, grinding, mixing and finishing T&P and scaffolding material and cost of material with all lead and lift.2. The rates cover protection of all place and things, requiring protection and cleaing such places and thing of all droppings and splashes of mortar etc. 21 Cement concrete flooring grade 1:2:4 (1-cement :2- coarse sand :4-graded stone aggregate ) rounding off edges etc.but excluding cost of nosing of steps etc. complete.Note :1. The rates for all items inculde all form of work, laying, curing and finishing etc. The rates are for complete work at site, inclusive of all leads.2. The rates cover the preparation and cleaing of all places 22 25 mm thick with 12.5 mm thick nominal size aggregate. 23 75 mm thick with 20 mm thick nominal size aggregate. 24 Masonryfor foundation and plinth 25 Randon Rubble stone masonry for foundation and plinth in cement sand mortar 1:6(1 Cement : 6 Sand) including labour charges. 26 Brick masonry for foundation and plinth in Cement sand mortar 1:6( 1 Cement : 6 Sand ) including labour charges. 27 Safe carriage of PCC poles including loading / un-loading 28 a)9 Mtr. Long-400 Kg /11 Mtr.PCC pole 29 Within10 Kms. 30 Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof. 31 c) 9 Mtr.long 200 Kg. PCC pole 32 within10 Kms.- 33 Above 10 Km. & upto 30 Km. add foreach Km. or part thereof 34 Safe carriage of steel( fabricated and unfabricated) I.e.M.S. Rails, R.S.Joists, M.S.Channels, M.S.Angles, M.S.Flat, G.I.Stay Sets, G.I. Stay Wire, G.I.Wire Nut & Bolts etc. and ACSR Conductor including loading and unloading and stacking in Nigam store /at work site 35 Within10 Kms. 36 Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof. 37 Above 30 Kms. Add for each Kms. or part thereof. 38 Safe Carriage of insulator, hardware, cable etc.including loading/unloading and stacking in Nigam.stores etc. 39 Within10 Kms. 40 Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof. 41 Above 30 Kms. Add for each Kms. or part thereof. 42 Safe carriage of fabricated lattice towers structures and sub-station structures type AB, AB beams, isolators structures etc. including loading/unloading and stacking in the Nigam. Stores / at work site. 43 Within10 Kms. 44 Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof. 45 Above 30 Kms. Add for each Kms. or part thereof. 46 Safe carriage of 11/.4 KV 3 Phase distribution transformer including loading/unloading.from store to site(b)25 & 40 KVA 47 Within10 Kms. 48 Above 10 Kms. & upto 30 Kms Add for each Km.or part thereof. 49 Above 30 Kms. Add for each Kms. or part thereof. 50 Safe Carriage of 33/11 KV Power Transformer (b) Above 1.6 MVA & Upto 3.15 MVA 51 Within 10 Kms 52 Above 10 Kms & upto 30 Kms .Add for each Km or partthereof 53 Above 30 Kms & upto 50 Kms . Add for each Kmor partthereof 54 Above 50 Kms . Add for each Km or part thereof 55 c) 5.0 MVA 56 Within 10 Kms 57 Above 10 Kms & upto 30 Kms .Add for each Km or partthereof 58 Above 30 Kms & upto 50 Kms . Add for each Kmor partthereof 59 Above 50 Kms . Add for each Km or part thereof 60 Safe carriage of breakers/kiosks etc. including loading/ unloading and stacking in Nigam stores 61 Within 10 KMs. 62 Above 10 Kms. and upto 30 Kms.Add per each km,or part thereof 63 Above 30 Kms. Add for each Kms. or part thereof. 64 Safe Carriage of 33/11 KV Power Transformer 65 8.0 MVA 66 Within 10 Kms 67 Above 10 Kms & upto 30 Kms .Add for each Km or partthereof 68 Above 30 Kms & upto 50 Kms . Add for each Kmor partthereof 69 Above 50 Kms . Add for each Km or part thereof 70 Safe loading of power/ distribution transformer. 71 Above 1.6 MVA & upto 3.15 MVA 72 Above 3.15 MVA & upto 5.0 MVA 73 Above5.0 MVA Amendment reference D.810 dt.10.10.16 74 Safe unloading of power/distribution transformers 75 Above 1.6 MVA & upto 3.15 MVA 76 Above 3.15 MVA 77 Erection of PCC poles in excavated pit with fixing of brackets,cross arms & top hampers as required in alignment after checking the same with plumb line. The support is to be back filled with soil with proper ramming. The nuts & bolts are to be provided by the contractor as per Nigams specification for which the payment will be made at the prevailing Discom store issue rates. 78 (B) IN RURAL AREA 79 PCC Poles 9 Mtr. Long (400 Kg) 80 PCC Poles 9 Mtr. Long(200Kg.) 81 Erection &assembly of 2 Pole structures of steel supports or PCC poles in excavated pit in alignment after checking the same with plumb line.Including fixing of top bracing of M.S.Channels with pilot plates and clamps.The support is to be back filled with soil with proper ramming.The nuts &bolts are to be provided by the contractor as per Nigams specfication for which the payment will be made at the prevailing Discom store issue rates. 82 PCC Poles 9 Mtr. Long(200 Kg.) 83 Erection & fixing of G.I.Stay sets with anchor plates in excavated pit in required position and back filling with soil with proper ramming.The work includes fixing of stay clamps.Stay insulator with stay wire at both ends with proper tension.Size of stay set/stay wire 84 8x3/4 with 7/8 SWG stay wire 85 6x5/8 with 7/10 SWG stay wire 86 Providing and laying of cement concrete in ratio 1:3:6 using 43 grade cement,river sand and 12 mm to 20 mm graded blast crusher broken in pit/foundation according to the size/type of supports/stay set including compaction/curing for 21days in steel plates shuttering /farmer base. 87 Fixing of all type of fabricated material on erected supports with nut & bolts as per approved design & drawing of sub-station. 88 Fixing of 11kv B&S/T&C type disc insulator for 33kv lines (each unit consiting of 3 nos .disc.& 1set of H/W) on terminal point including fixing of hardware and strips. 89 Fixing of 11kv B&S/T&C type disc insulator of 11kv lines(each unit consiting of 1nos.disc.& 1set of H/ W ) on terminal point including fixing of hardware and strips. 90 Fixing of 11kv B&S/T&C type disc insulator of 11kv lines(each unit consiting of 2 nos.disc.& 1set of H/ W ) on terminal point including fixing of hardware and strips. 91 Fixing of 33kv pininsulator with pins. 92 Assembly. Installation & commissioning of gang operated isolating switch on erected structure with setting for accurate operation including fixing of allied accessories completein all respect with post insulator and jumpering on both ends for connection with the system. The nuts and bolts will be supplied by the contractor for which payment will be made as per prevailing Discom store issue rates.(B)G.O. switch . without earthing blade. 93 33kv G.O.switch 94 11kv G.O.switch 95 Assembly and installation of Horn Gap fuse set (set of 3nos)on erected structure as per design, complete in all respectwith post insulator includingjumperingonbothendsforconnection with the system. The nuts & bolts will be supplied by the contractorfor which payment will be made as per prevailing Discom store issue rates. 96 33kv Horn Gap fuse set. 97 11kv Horn Gap fuse set. 98 Installation of lightening arrestors on erected structure /support (set of 3 nos) including connection with earth by wire /strip as required and jumpering etc. The nuts & boltswill be supplied by the contractorfor which payment willbe madeas per prevailing Discom store issue rates,(A)sub-station type 99 33 KV L.A. set ( 1set=3 Nos) 100 11 KV L.A. set ( 1set=3 Nos) 101 Installation testing as per Nigams norm & commissioning of 11/0.4KV distribution transformer on erected supports including fixing of base channels as per requirment jumpering on HV&LV side, crimping of lugs/ clamping earth connections of body and neutral of transformer with wire /strip (as already provided with earthing ) complete in all respect. The PG clamps nuts & bolts will be supplied by the contractorforwhich payment will be made as perprevailing Discom store issue rates, 102 25 and 40 KVA 103 Fixing of danger plates on supports/structure 104 Fixing of PG clamp of Weasel /Rabbit Conductor 105 Fixing of PG clamp of Dog /Racoon Conductor 106 Assembly,installation & commisioning of 11 KV Roaster switchs on erected structures with stting for accurate operation including fixing of allied accessories completed in all respect with post insulators and jumpering on both ends for connection with systm.The nuts & bolts will be supplied by contractor for which payment will be made as per prevailing Dicom store issue rates. 107 Three no. Earthing of 11/0.4 KV distribution transformer /sub-station withM.S.Rod 20mm dia each 3 meter long and driving them into earth by mechanical means at a distance as per approved design & drawing & specification.The work includes flattening of top ends of M.S.rod drilling a hole of 9/16 dia.at flattened top and tightening of M.S.flat 50x6mm/25x3 mm (having 3 hole 2ends and 1mm middle) with nuts and bolts with M.S.rods top end hole.The flat will also be welded with M.S.rod.The end will be connected to equipments as under in sequence. 108 Mesh earthing for 33/11 kv sub-station as per approved map &design usingMS flat 50X6mm/MS road 20mm dia includinglaying of flat/rod at the depth of 0.65 Mtrs.,welding & jointing at joints , structures & equipments etc.asunder: 109 Excavation of trench of 0.65Mtrs.depth and 0.5Mtr.width 110 Hard Soil 111 Ordinary rock ( where blasting is not required.) 112 Laying of MS flat /MS rod in 0.65Mtr.deep excavated trench and welding of MS flat/rod continuosly with 100 mm overlaping for straight joint including coating of MS flat joints with molten bitumen and covering joint with bitumen impregnated tape to protect from rust. 113 Shaping of MS flat for connecting the equipments with earthmesh .The work includes the welding of MS flat with equipments/structure and also with earth mesh.The work also includescoating of MS flat joint with molten bitumen and covering jointwith bitumen impregnated tape to protect from rust. 114 Preparation of spikes made of M.S Rod of 20 mm dia and 3 Mtr.length as per design and requirment to be driven in earth by mechanical means and Providing & .fastening of suitable clampswith the M.S. Rod, connection of earth wire/stay wire/MS flat in clamp depending on type of soil: 115 Where drilling isrequired 116 Filling of trench with available excavated muck in layers of 20cm (Max.)consolidating each deposited layer by ramming & watering with lead up to 50 Mtr, and lift up to 1.5 Mtr. 117 Painting of exposed portion of MS flat/rod with two coats of red-oxide primer and two coats of green enamel paint.including material. 118 Earthing of new 33/11 KV S/S with bentonite compound (including material ) involving following activities. (8.5.1 TO 8.5.6 COVERED) 119 Pipe Earthing for Power Transformer at 33/11KV S/S :-Supply and erection of earthing electrode shall consist of G.I. Pipe 100 mm, of 3 Mtr. Length. The electrode shall be buried as far as practicable 3 Meters below ground level. Wherever possible earth electrodes shall be located as near the water tap, water drain or near down take pipe. Earth electrodes shall not be installed in proximity to a metal fance. It shallbe kept clear of the bulidings foundations and in no case it shall be nearer than 2 Mtr. from the outer face of the wall. The electrode shall be surrounded with layer of charcoal dust and salt mixture through out the length. The 100 mm G.I. pipe shall be provided with holes of 12 mm Dia drilled at 75mm interval upto 2.5 meters length from bottom. The top of the pipe shall be provided with a G.I. threaded cap for watering the earth through a pipe. A clamp with pati of 12 of M.S. Flat of size 50x6 mm shall be fixed (Bolted) on the top age of the pipe which in turn shall be connected Neutral/Body of the Power Transformer through M.S. Flat size 50x6 mm. The G.I. cap over the G.I. Pipe shall be housed in a masonry chamber, approximately 300 mm x 300 mm x 300 mm deep. The masonry chamber shall be provided with a RCC Inspection cover resting over a RCC frame, embedded in masonry. 120 Erection of PCC poles in excavated pit in alignment after checking the same with plumb line as per approved design & drawing of 33/11kv sub-station.The pit should be back filled with the soil with proper ramming below 30cm ground level and then muffed above 15cm average ground level with cement concrete ratio1:3:6.The charges formuffing will bepaid extra as per chapter code no 5.7 The nuts & bolts will be supplied by the contractorfor which payment will be made at the prevailing store issue rates.(B) IN RURAL AREA 121 PCC Poles 9 Mtr. Long 122 Laying / stringing of bus bar with ACSR Dog & jumper connection using tie rod ,33KV /11KV insulator strings,required hardware,P.G.clamps/T clamps etc.as per requirement including Y-connections at bus bar jumpering point as per the direction of engineer in-charge. 123 ACSR Panther 124 ACSR DOG/RABBIT 125 Supply, stacking & spreading of stone boulders 40 mm. Mono size.(Less voids 17%) 126 Erection of OCB/Kiosk/VCB complete with accessories including use of special tools & conducting all pre-commissioning test before energization,filling oil etc. complete in all respect with erection & grouting of structure (excluding civil works). The relays will be tested by Discom. 127 33 KV VCB/SF-6 Breaker 128 11 KV VCB (Outdoor ) 129 Installation of current/potential transformers on supporting structure including checking of wiring & conducting all pre-commissioning tests before energization & satisfactory operation in all respect (The CT/PT set will be tested by Discom). 130 33KV CT(1 set of 3 Nos.) OR PT Set 131 11 KV CT(1 set of 3 Nos.) OR PT Set 132 Laying, testing termination of control cable 1100 volts PVC insulated including supply and installation of ferrules to designate various cores of control cables by terminal Nos. of identification including utilization of cable gland. The control cable should be clearly arranged in trenches avoiding crossings including clamping of control cable at regular interval and providing identify tags. 133 12x2.5 Sq.mm. 134 Installation of metering points on 11 KV Out going feeder at 33/11 KV S/S.(a to g) 135 Painting with priming coats or ready mixed red-oxide paint 2 coats of approved make on steel works after cleaning with wire brush / sand paper.(including cost of red oxide) 136 On new surface 137 Painting with aluminium paint of approved brand and manufacturer to give an even surface.(includingcost aluminium paint) 138 On new works with two coats. 139 Fabrication of steel structures of M.S angle ,M.S.channel & M.S.Flat including cutting ,drillingas per design and drawing. 140 Other steel items 141 Drilling of holes in MS Channel / Angle /Flat 142 15/16 dia holes(23.81 mm dia.) 143 Transportation of CT/PT set (all size) including loading and unloading from Nigam store to site 144 (a) Within 10 Kms. 145 (b) Above 10 Km upto 30 Km. Add for each Km. or part there off 146 Supply of MS nuts & bolts 147 Supply of PG Calmps 148 33 KV Line work Annexure -B 149 Conducting route survey as per approved route map and pegging of route with tee off point section point & double pole locations. 150 Trimming of tree branches/plants and preparing route approchases for proposed line. 151 Excavation of pit in soil (ordinary) to erect various supports and stay sets including stacking of excavated soil from the edgeof excavation. 152 (A) Height of poles/R.S.Joist/M.S. Rail Size of pit 153 9 Mtr/ 1.2mx0.6mx1.50 m deep 154 (B) Lattice Tower /Size of pit 155 11.4/10.8 Mtr/ 1.5mx1.5m x1.80 m deep 156 12.8/12.6 Mtr/ 1.5mx1.5m x2.10 m deep 157 (C)Stay set/Depth of pit 158 8x 3/4 -0.75x0.5x1.6 m 159 Excavation of pit in Hard soil 160 (A) Height of poles/R.S.Joist/M.S. Rail Size of pit 161 9 Mtr/ 1.2mx0.6mx1.50 m deep 162 (B) Lattice Tower /Size of pit 163 11.4/10.8 Mtr/ 1.5mx1.5m x1.80 m deep 164 12.8/12.6 Mtr/ 1.5mx1.5m x2.10 m deep 165 (C)Stay set/Depth of pit 166 8x 3/4 -0.75x0.5x1.6 m 167 Excavation of pit in ordinary rock which does not require blasting to erect various supports and stay sets including stacking of excavated muck from the edge of excavation/pit. 168 (A) Height of poles/R.S.Joist/M.S. Rail /Size of pit 169 9 Mtr/ 1.2mx0.6mx1.50 m deep 170 (B) Lattice Tower /Size of pit 171 11.4/10.8 Mtr/ 1.5mx1.5m x1.80 m deep 172 12.8/12.6 Mtr/ 1.5mx1.5m x2.10 m deep 173 (C)Stay set/Depth of pit 174 8x 3/4 -0.75x0.5x1.6 m 175 Excavation of pit in Hard rock ( Where blasting is required)to erect various supports and stay sets including stacking of excavated muckfrom the edge of excavation/pit. 176 (A) Height of poles/R.S.Joist/M.S. Rail /Size of pit 177 9 Mtr/ 1.2mx0.6mx1.50 m deep 178 (B) Lattice Tower /Size of pit 179 11.4/10.8 Mtr/ 1.5mx1.5m x1.80 m deep 180 12.8/12.6 Mtr/ 1.5mx1.5m x2.10 m deep 181 (C)Stay set/Depth of pit 182 8x 3/4 -0.75x0.5x1.6 m 183 Safe carriage of PCC poles including loading / un-loading 184 a)9 Mtr. Long-400 Kg /11 Mtr.PCC pole 185 Within10 Kms. 186 Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof. 187 Safe carriage of steel( fabricated and unfabricated) I.e.M.S. Rails, R.S.Joists, M.S.Channels, M.S.Angles, M.S.Flat, G.I.Stay Sets, G.I. Stay Wire, G.I.Wire Nut & Bolts etc. and ACSR Conductor including loading and unloading and stacking in Nigam store /at work site 188 Within10 Kms. 189 Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof. 190 Above 30 Kms. Add for each Kms. or part thereof. 191 Safe Carriage of insulator, hardware, cable etc.including loading/unloading and stacking in Nigam.stores etc. 192 Within10 Kms. 193 Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof. 194 Above 30 Kms. Add for each Kms. or part thereof. 195 Safe carriage of fabricated lattice towers structures and sub-station structures type AB, AB beams, isolators structures etc. including loading/unloading and stacking in the Nigam. Stores / at work site. 196 Within10 Kms. 197 Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof. 198 Above 30 Kms. Add for each Kms. or part thereof. 199 Erection of all type of steel supports in the excavated pit in alignment after checking the same with plumb line including fixing of cross arms and top hamper before erecting the supports. The support should be grouted and muffed in cement concrete of ratio 1:3:6 as per item No. 5.7 the remaining portion of the pit will be back filled with soil. The nuts & bolts will be provided by the contractor as per Nigams specification for which payment will be made at the prevailing store issue rates. The cost muffing and grouting will be paid extra. 200 Lattice Structure 201 Providing and laying of cement concrete in ratio 1:3:6 using 43 grade cement,river sand and 12 mm to 20 mm graded blast crusher broken in pit/foundation according to the size/type of supports/stay set including compaction/curing for 21days in steel plates shuttering /farmer base. 202 Erection of PCC poles in excavated pit with fixing of brackets,cross arms & top hampers as required in alignment after checking the same with plumb line. The support is to be back filled with soil with proper ramming. The nuts & bolts are to be provided by the contractor as per Nigams specification for which the payment will be made at the prevailing Discom store issue rates. 203 PCC Poles 9 Mtr. Long (400 Kg) 204 Erection &assembly of 2 Pole structures of steel supports or PCC poles in excavated pit in alignment after checking the same with plumb line.Including fixing of top bracing of M.S.Channels with pilot plates and clamps.The support is to be back filled with soil with proper ramming.The nuts &bolts are to be provided by the contractor as per Nigams specfication for which the payment will be made at the prevailing Discom store issue rates. 205 PCC Poles 9 Mtr. Long(400 Kg.) 206 Erection & fixing of G.I.Stay sets with anchor plates in excavated pit in required position and back filling with soil with proper ramming.The work includes fixing of stay clamps.Stay insulator with stay wire at both ends with proper tension.Size of stay set/stay wire 207 8x3/4 with 7/8 SWG stay wire 208 Assembly. Installation & commissioning of gang operated isolating switch on erected structure with setting for accurate operation including fixing of allied accessories completein all respect with post insulator and jumpering on both ends for connection with the system. The nuts and bolts will be supplied by the contractor for which payment will be made as per prevailing Discom store issue rates.(B)G.O. switch . without earthing blade. 209 33kv G.O.switch 210 Laying ,jointing , stringing, tensioning and clamping of conductor with proper sag as directed , using bolted type hardware including binding on pin insulators,jumpering on section points with binding wire / P.G.clamps.Aluminium jointing sleeves will be used for jointing the conductor.The line must stand at proper voltage on charging.The contractor will be provide P.G.clamps for which payment will be made as per prevailing Discom issue rate. 211 (B) IN RURAL AREA 212 ACSR DOG 213 Fixing of 33kv pininsulator with pins. 214 Fixing and assembly of disc.point channel pair with pilot plates&clamps on erected double pole structure as per design. The nuts &bolts are to be provided by the contractor as per Nigams specification for which payment will be made as perprevailing Discom store issue rates. 215 33 KV line 216 Laying , jointing,stringing,tensioning and clamping of G.I.Earthwire continuosly on single/double pole by using earth clamps /nuts & bolts with washers and earth reel etc.including proper binding at each end.The nuts and bolts will be supplied by thecontractor for which payment will be made as per prevailing Discom store issue rates. 217 (A).In Urban Area 218 G.I.Earth wire 6 SWG 219 G.I.Earth wire 8 SWG 220 (A).In Rural Area 221 G.I.Earth wire 6 SWG 222 G.I.Earth wire 8 SWG 223 Earthing of line for all type of supports as per REC construction standards using Stay wire/GI wire with onepcs.of M.S.rod20mm dia each 3 meter long and driving into earth by mechanical means as per approved design.Drawing &specification.All material except MS rod,MS flat & stay wirewill be supplied by the contractor.If material is supplied by the contractor ,the payment will be made as per prevailing Discomstore issue rates.(In case of PCC poles earthing must be connected with earthwire already available on PCC pole at bottom) 224 Fixing of 11kv B&S/T&C type disc insulator for 33kv lines (each unit consiting of 3 nos .disc.& 1set of H/W) on terminal point including fixing of hardware and strips. 225 Supply of MS nuts & bolts 226 Supply of PG Calmps 227 Fixing of PG clamp of Dog /Racoon Conductor 228 Fabrication of steel structures of M.S angle ,M.S.channel & M.S.Flat including cutting ,drillingas per design and drawing. 229 Other steel items 230 Drilling of holes in MS Channel / Angle /Flat 231 15/16 dia holes(23.81 mm dia.) 232 Laying of 33 KV XLPE Cable ( Aluminium Conductor ) underground as per relevant ISS / AVVNL standard including excavation of 30 cm width x120 cm deep trench in Kaccha land 25 cm thick under layer of sand.A class bricks or concrete block covering refilling soil in the remaining portion and providing/fixing cable route indicators at every 30Mtr.of cable and at every turn. 233 B) 3x240 Sq mm to 3x400 Sq mm 234 Note:- Per mtr. Rate shall be paid extra for excavation of puccka road 235 Laying of two (D/C) 33KV, XLPE (Aluminium conductor) undrground cables w/o overlapping as per relevant IS/ AVVNL standard including excavation of 50 cm width x 120 cm deep trench in Kaccha land.25 cm thick under layer of sand.A class bricks or concrete block covering refilling soil in the remaining portion and providing/fixing cable route indicators at every 30Mtr.of cable and at every turn. 236 A) 3x50 Sq mm to 3x185 Sq mm 237 B) 3x 240 Sq mm to 3x400 Sq mm 238 Note:- per meter shall be paid extra for excavation in Pakka Road. 239 Laying of 33 KV & 11KV XLPE cable without Road cutting i.e. through burrowing machine VERMIER.(120 cm deep).Use of this technology must be restricted to the situation like:- 240 (iii)When cable laid in a HDPE pipe 241 33/ 11 KV 3C x 300 Sq.mm cable 242 Add Cost of 200 HDPE pipe 243 (b)HDPE DWC pipe(IS-14930) 244 Intallation of 33 KV Cable (XLPE) termination / straight through joints ( Heat shrinkable type) as per manufacturers kit guidance and direction including preparation of cable and testing refilling etc as required.(Including crimping of lugs) 245 A) (ii) 3x240 Sqmm to 3x400 Sq mm 246 C) (ii) Straight through joint3x240 Sq mm to 3x400 Sq mm 247 Providing and fixing of G.I. Pipe of 150 mm diameter. B-Class (IS:1239 mark),at the starting and finishing point of 33 KV under ground cables and to lay & clamp vertically with the existing support including labour charges. 248 11 KV Line work Annexure -C 249 Conducting route survey as per approved route map and pegging of route with tee off point section point & double pole locations. 250 Trimming of tree branches/plants and preparing route approchases for proposed line. 251 Excavation of pit in soil (ordinary) to erect various supports and stay sets including stacking of excavated soil from the edgeof excavation. 252 (A) Height of poles/R.S.Joist/M.S. Rail Size of pit 253 9 Mtr/ 1.2mx0.6mx1.50 m deep 254 (B) Lattice Tower /Size of pit 255 11.4/10.8 Mtr/ 1.5mx1.5m x1.80 m deep 256 12.8/12.6 Mtr/ 1.5mx1.5m x2.10 m deep 257 (C)Stay set/Depth of pit 258 6x 5/8 -0.75x0.5x1.35 m 259 Excavation of pit in Hard soil 260 (A) Height of poles/R.S.Joist/M.S. Rail Size of pit 261 9 Mtr/ 1.2mx0.6mx1.50 m deep 262 (B) Lattice Tower /Size of pit 263 11.4/10.8 Mtr/ 1.5mx1.5m x1.80 m deep 264 12.8/12.6 Mtr/ 1.5mx1.5m x2.10 m deep 265 (C)Stay set/Depth of pit 266 6x 5/8 -0.75x0.5x1.35 m 267 Excavation of pit in ordinary rock which does not require blasting to erect various supports and stay sets including stacking of excavated muck from the edge of excavation/pit. 268 (A) Height of poles/R.S.Joist/M.S. Rail /Size of pit 269 9 Mtr/ 1.2mx0.6mx1.50 m deep 270 (B) Lattice Tower /Size of pit 271 11.4/10.8 Mtr/ 1.5mx1.5m x1.80 m deep 272 12.8/12.6 Mtr/ 1.5mx1.5m x2.10 m deep 273 (C)Stay set/Depth of pit 274 6x 5/8 -0.75x0.5x1.35 m 275 Excavation of pit in Hard rock ( Where blasting is required)to erect various supports and stay sets including stacking of excavated muckfrom the edge of excavation/pit. 276 (A) Height of poles/R.S.Joist/M.S. Rail /Size of pit 277 9 Mtr/ 1.2mx0.6mx1.50 m deep 278 (B) Lattice Tower /Size of pit 279 11.4/10.8 Mtr/ 1.5mx1.5m x1.80 m deep 280 12.8/12.6 Mtr/ 1.5mx1.5m x2.10 m deep 281 (C)Stay set/Depth of pit 282 6x 5/8 -0.75x0.5x1.35 m 283 Safe carriage of PCC poles including loading / un-loading 284 c) 9 Mtr.long 200 Kg. PCC pole 285 within10 Kms.- 286 Above 10 Km. & upto 30 Km. add foreach Km. or part thereof 287 Safe carriage of steel( fabricated and unfabricated) I.e.M.S. Rails, R.S.Joists, M.S.Channels, M.S.Angles, M.S.Flat, G.I.Stay Sets, G.I. Stay Wire, G.I.Wire Nut & Bolts etc. and ACSR Conductor including loading and unloading and stacking in Nigam store /at work site 288 Within10 Kms. 289 Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof. 290 Above 30 Kms. Add for each Kms. or part thereof. 291 Safe Carriage of insulator, hardware, cable etc.including loading/unloading and stacking in Nigam.stores etc. 292 Within10 Kms. 293 Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof. 294 Above 30 Kms. Add for each Kms. or part thereof. 295 Safe carriage of fabricated lattice towers structures and sub-station structures type AB, AB beams, isolators structures etc. including loading/unloading and stacking in the Nigam. Stores / at work site. 296 Within10 Kms. 297 Above 10 Kms. & upto 30 Kms. Add for each Km.or part thereof. 298 Above 30 Kms. Add for each Kms. or part thereof. 299 Fixing of 11 KV pininsulator with pins. 300 Fixing of 11kv B&S /T&C type disc insulator of 11kv lines(each unit consiting of 1nos.disc.& 1set of H/W ) on terminal point including fixing of hardware and strips. 301 Fixing of PG clamp of Weasel /Rabbit Conductor 302 Earthing of line for all type of supports as per REC construction standards using Stay wire/GI wire with onepcs.of M.S.rod20mm dia each 3 meter long and driving into earth by mechanical means as per approved design.Drawing &specification.All material except MS rod,MS flat & stay wirewill be supplied by the contractor.If material is supplied by the contractor ,the payment will be made as per prevailing Discomstore issue rates.(In case of PCC poles earthing must be connected with earthwire already available on PCC pole at bottom) 303 Fabrication of steel structures of M.S angle ,M.S.channel & M.S.Flat including cutting ,drilling and continunous welding joint as per design and drawing. 304 Other steel items 305 Drilling of holes in MS Channel / Angle /Flat 306 15/16 dia holes(23.81 mm dia.) 307 Supply of MS nuts & bolts 308 Erection of all type of steel supports in the excavated pit in alignment after checking the same with plumb line including fixing of cross arms and top hamper before erecting the supports. The support should be grouted and muffed in cement concrete of ratio 1:3:6 as per item No. 5.7 the remaining portion of the pit will be back filled with soil. The nuts & bolts will be provided by the contractor as per Nigams specification for which payment will be made at the prevailing store issue rates. The cost muffing and grouting will be paid extra. 309 Lattice Structure 310 Providing and laying of cement concrete in ratio 1:3:6 using 43 grade cement,river sand and 12 mm to 20 mm graded blast crusher broken in pit/foundation according to the size/type of supports/stay set including compaction/curing for 21days in steel plates shuttering /farmer base. 311 Erection of PCC poles in excavated pit with fixing of brackets,cross arms & top hampers as required in alignment after checking the same with plumb line. The support is to be back filled with soil with proper ramming. The nuts & bolts are to be provided by the contractor as per Nigams specification for which the payment will be made at the prevailing Discom store issue rates. 312 (B) IN RURAL AREA 313 PCC Poles 9 Mtr. Long(200Kg.) 314 Erection &assembly of 2 Pole structures of steel supports or PCC poles in excavated pit in alignment after checking the same with plumb line.Including fixing of top bracing of M.S.Channels with pilot plates and clamps.The support is to be back filled with soil with proper ramming.The nuts &bolts are to be provided by the contractor as per Nigams specfication for which the payment will be made at the prevailing Discom store issue rates. 315 PCC Poles 9 Mtr. Long(200 Kg.) 316 Erection & fixing of G.I.Stay sets with anchor plates in excavated pit in required position and back filling with soil with proper ramming.The work includes fixing of stay clamps.Stay insulator with stay wire at both ends with proper tension.Size of stay set/stay wire 317 6x5/8 with 7/10 SWG stay wire 318 Fixing and assembly of disc.point channel pair with pilot plates top hampers & clamps on erected single polestructure as per design. The nuts &bolts are to be provided by the contractor as per Nigams specification for whichpayment will be made as per prevailing Discom store issue rates, 319 11 KV line 320 Laying ,jointing , stringing, tensioning and clamping of conductor with proper sag as directed , using bolted type hardware including binding on pin insulators,jumpering on section points with binding wire / P.G.clamps.Aluminium jointing sleeves will be used for jointing the conductor.The line must stand at proper voltage on charging.The contractor will be provide P.G.clamps for which payment will be made as per prevailing Discom issue rate. 321 (B) IN RURAL AREA 322 ACSR DOG 323 ACSR RABBIT 324 ACSR WEASEL 325 INSULATED RABBIT HT/LT 326 Supply of PG Clamps 327 Laying of 11 KV, XLPE, Cable (Aluminium conductor) underground as per relevant IS/AVVNL standards including excavation of 30 cm x 120 cm deep trench in Kaccha land 25 cm thick under layer of sand. A class beicks covering refilling soil in the remaining(Including fixing of G.I.Pipe of required size at both end with 3 Mtr projected above the ground surface & 0.3 Mtr. below ground level) 328 A) 3x50 Sq mm to 3x185 Sq mm cable 329 Note:- Per mtr. Rate shall be paid extra for excavation of puccka road 330 Laying of two (D/C) 11 KV, XLPE, Cable (Al. conductor) underground cable w/o overlapping as per relevant IS/AVVNL standards including excavation of 50 cm width x120 cm deep trench in Kaccha land, 25 cm thick under layer of sand. A class bricks or concrete block covering refilling soil in the remaining portion and providing/fixing cable route indicators at every 30Mtr.of cable and at every turn. 331 A) 3x50 Sq mm to 3x185 Sq mm cable 332 Note:- per meter shall be paid extra for excavation in Pakka Road. 333 Laying of 33 KV & 11KV XLPE cable without Road cutting i.e. through burrowing machine VERMIER.(120 cm deep).Use of this technology must be restricted to the situation like:- 334 (iii)When cable laid in a HDPE pipe 335 B)33/ 11 KV below 3C x 300 Sq.mm cable 336 Add Cost of 200 HDPE pipe 337 (a) HDPE DWC pipe(IS-14930) 338 Installation of cable termination / straight through joints on 11KV Aluminium conductor XLPE /PILCA Cable with outdoor/ indoor termination end and /or straight through joint including required excavation / remoral/ fixing / refixing/ testing etc. as required 339 A) (I) Outdoor end terminal3x35 Sq mm to 3x185 Sq mm 340 C) (I) Straight through joint 3x35 to 3x185 Sq mm 341 Providing and fixing of G.I. Pipe of 125 mm diameter. B-Class (IS:1239 mark),at the starting and finishing point of 11 KV under ground cables and to lay & clamp vertically with the existing support including labour charges.
