Tender For Provision Of Training Shed And Sanitary Annex Male And Female At Sa Range At Af Stn Car Nicobar.; 1 Excavation in trenches n.exc 1.5 M wide and n. exc 1.5 M depth and getting out in soft/loose soil getting out complete all as specified and as directed. 2 Material and labour for plain cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation filling and mass concrete including necessary form work complete all as specified and as directed. 3 M&L for Pre-cast cement concrete block masonry withsolid blocks using type C1(1:3:6) (20mm graded aggregate) ,size exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed. 4 Material and labour for reinforced cement concrete 1:2:4, type B1,using 20 mm graded granite stone aggregate in foundaions including rafts, footings, foundaion beams, plinth beams, bases for columns etc, basement slabs, underreamed piles and mass concrete all as specified and as directed. Note : Reinforcement and form workshall be measured and paid separately. 5 Supply and fix rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats conforming to Fe-410W(Gde E-250) quality Acomplete all as specified and as directed. 6 Supply and Fixing Mild steel work such as joist, channel, angle or tee section fixing independentlywithout connecting plates, cut to ordinary length ie, within 20mm of the length indicated conforming to Grade E-250, Fe 410 W quality B all as specified and as directed. 7 Material and labour for providing reinforced cement concrete 1:2:4 type B1 nominal mix using 20mm graded stone aggregate as in hajjas supported on walls, beams and columns using all as specified anddirected. 8 Material and Labourfor TMT bar 10mm dia and over, cut to length, bent to shape required, including cranking,bending spirally for hooping ,for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 9 M&Lmild steel TMT bars 5mm diaandover up to 10mm for stirrups cut to length , bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia bars confirming to Fe-410-S or Fe-410-0complete in all respect as specified and directed. 10 Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings, and similar work, not exceeding 200 mm thick etc, fair finshed surfaces of concrete (Horizontal or sloping) complete all as specified and as directed. 11 Use and waste of form work to edges of concrete flats, threads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exceeding 10 cm but not exceeding20 cm wide for fair finished surfaces. 12 Material and Labour for rendering 5 mm thick in cement mortar 1: 4 on fair faces of concrete surfaces of ceilingfinished even and smooth with out using extra cement, complete all as specified. 13 Material and labour for 15 mm thick renderingon brick/concrete surfaces in two layers in CM 1:4, finished even and smooth without using extra cement complete all as specified and as directed. 14 Material and labour for rendering 15 mm on fair faces of brick or concrete surfaces in CM 1:6, finished even and fair without using extra cement complete all as specified and directed. 15 Material and labour for preparation of of new plastered/concrete surfaces of walls and applying two coats ofacrylic distemperof approved shade/tint over a coat of primer,over 3mm thick wall care putty finish to achieveuniform smooth surface of wallall as specified and as directed. 16 Material and Labour for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and as directed. 17 Material and labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. 18 Supply and fixing 6 mm thick bevelled edge looking mirror of size 600 x 450 mm mounted on 6 mm thick AC Building board or commercial plywood/hard board backing andfixed to wooden plugs with CP Screws and cup washersall as specified and as directed. 19 Supply and fixing in repairs vitreous China wash hand basin, white (flat back or angle back type or counter top) of size 550X400mm including 32mm brass chromium plated waste fitting, a pair of cast iron bracket duly painted including cutting and pinning in ends making good disturbed surfaces in CM 1:3 excluding pillar tap but chain , plug and porcelain stopper, brackets etc all as specified and as directed. 20 Supply and fix stop valves/angle cock, 15mm bore, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. 21 Supply and Fix vitreous china wash down water closet Pedastal patternwhite (excluding flushing cistren ) including trap set, seat cover and fixing of flushing cistern, brackets, flushing pipeetc, etc. withP or S trap, making good the floor to match with existing floor complete all as specified and as directed. 22 Supply and fixingVitreous China full stall urinal bowl type (back or corner wall type), white , of size 580mm x 380mm x 350mm complete with chromium plated waste fittings including providing and fixing plugs,bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing arround urinal back in cement, (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) all as specified and as directed. 23 Supply and fixing galvanised steel water tubing medium grade 15 mm bore including all necessary fittings such as bends, L bows, short piece connections, backnuts, caps plugs, unions couplings, flanges, sockets etc,fixed to wall/floor/ceilingincluding necessary cutting/chauging in walls made of brick/concrete surface complete all as specified and as directed. 24 Supply and fixing galvanised steel water tubing medium grade 20 mm bore including all necessary fittings such as bends, L bows, short piece connections, backnuts, caps plugs, unions couplings, flanges, sockets etc,fixed to wall/floor/ceilingincluding necessary cutting/chauging in walls made of brick/concrete surface complete all as specified and as directed. 25 Supply and fix Bib taps, 15mm bore, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed. 26 Supply and fix aluminium powder coated frame for doors,windows, ventilators with one or more rebates with joint clip and using rubber beading etc complete all as specified and directed.Note:Glass panel/particle board panel filling shall be measured and paid separately. 27 Supply and fix for powder coated,Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.) completeallasspecified. 28 Supply and fix anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern of DG 102 pattern made out of 7.5mm rod,fixed with with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section of size 23.40mm x 15.30mm x 1.40mm thick around the opening, all complete as per requirement, specified and directed. 29 Material and labour forpreparation of newor previously untreated steel surface over 10 cm width or girth and applying two coats of synthentic enamel paint over a coat of red oxide primer complete all as specified and directed. 30 Supply and fix 4.00 mm thick sheet glass, ordinary quality and glazing with oil putty in squaren.exc 0.5 sqm in each pane, complete all as specified and as directed. 31 Material and labour for hard core with broken stone or boulders of gauge not exceeding 63 mm, deposited, spread, and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface all as specified and as directed. 32 Material and Labour for 75mm thick Plain Cement Concrete 1:3:6 type C2 using40 mm graded stoneaggregate as in plinth protection, floors, pavings and hardstanding etc, finished even smooth without using extra cement etc including necessary forwork, complete all as specified and as directed. 33 Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and as directed. 34 Removing excavated material (soil) exc 50 m n.exc 250 m and depositing where as directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed. 35 Supply and fixing Solid PVC Door Frame of size 50 mm x47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. Square tube, supporting& fixing in opening as per specification & drawing complete all as specified and directed. 36 Supply and fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame shall be covered with heat moulded plian colour PVC C channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement supplying and fixing in the frame at site as per specification & drawing of SSR Part II. 37 Supply and fix extruded aluminium alloy handles, fabricated type, anodised 150mm size complete all as specified and as directed 38 Supply and Fix 125mm long aluminium anodised barrel tower boltof extruded section all as specified and as directedby Eng-in-charge. 39 Supply and fixing aluminium alloy,anodised, sliding door boltof length 250mm with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded section or cast-aluminium alloy complete all specified and as directed. 40 Supply and fix 100mm long mild steel cold rolledmedium weightbutt hinges fixed with screws to wooden frames or with welding to steel frames including all accessoriescomplete all as specified and as directed. 41 Supply and fix in repair 10 Ltr capacity PVC valveless, syphonic action type, flushing cistern low level, white, with inlet ball valve, float and handle including brackets, flushing pipe, 450mm long PVC Connection and connection to trap, and to flushing and making good to floor complete all as specified . 42 Supply and fix in repairs PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. 43 Supply and fixCP 15mm, fancy type Health faucet setwith 1 mtr long flexible spring type steel tube & hook including fittingscomplete fixed in repairs all as specified. 44 Supply and fix 15mm dia pillar tap, cast copper alloy, chromium plated, fancy type, with capstan head screwed down high pressure with or without lettered hot or cold with long screw shank and fly nutt screw foriron pipeMake: CERA /Parryware/Hindware 45 Supply and fixing in repairs Towel rails tubular brass chromium plated 20 mm dia D type 60 cm long between flanges complete all as specified and directed. 46 Material and Labour for non-skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile of size 400 x 400 x 7 to 8mm thick in floors etc, set and jointed in cement mortar and pointed in white of coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.NOTE: No extra cost shall be allowed for removing and re-fixing and necessary cutting of door etc if any required during execution of work. 47 Material and Labour for glazed ceramic coloured tiles in vertical surface 450x300x7-8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles over and including 10mm thick backing coat in CM 1:4 cmplete all as specified. 48 Material and labour for 75mm thick plain cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregateas in sub base of floors including necessary form work all as specified and as directed. 49 Materialand Labour for 40mm thick plain cement concrete 1:2:4 type B1 using 20mm graded granite stone aggrgate as floor and other similar type of work, and finishing cement concrete surface even and smooth Without using extra cement, complete all as specified and as directed. 50 Supply and fix anodised aluminium snap grid frame work for false ceiling with 605mm x 605mm size, consisting of main Tee of size 40 x 40 x 2mm, cross Tee of size 40 x 40 x 2mm and wall angle of size 40 x 40 x 2mm of approved make including all necessary cuttings, fixing of aluminium section firmly in position with and including steel hangers 6 mm dia G.I. wire (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60 mm long and expansion hold fasteners 40 mm long in soffit of slab/walls complete all as specifed and as directed including provision of with 6 mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid, fixed in ceiling, flat or sloping, complete all as specified and directed.Note :- Rate quoted above shall be deemed to include for making holes, cutting chassis if any required and making good to existing walls in cement mortar 1: 3 to match with existing surface finish as directed at site. 51 S&F PVC (SWR) 75 mm bore vent cowl complete all as specified and as directed. 52 S&F in repair PVC (SWR) pipes 110 mm dia. single socketed, in any length with rubber ring joints, fixed to wall and roof as in rain water gutters including cutting of PVC pipes in half complete all as specified and as directed. 53 S&F PVC (SWR) pipes 75 mm dia. single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and as directed. 54 S&F PVC (SWR) bend 75 mm dia with access door complete all as specified and as directed. 55 Supply and fix PVC (SWR) floor trap , plain with grating including jointing with solvent cement 75mm bore complete all as specified and as directed. 56 S&F PVC (SWR) junction single 110 mm bore, (single T) equal or unequal with access door complete all as specified and as directed. 57 Surface dressing not exceeding 15 cm deep in soft/loose soilall as specified and as directed. 58 Materialand Labour for 100mm thick plain cement concrete 1:2:4 type B1 using 20mm graded granite stone aggrgate as floor and other similar type of work, and finishing cement concrete surface even and smooth Without using extra cement, complete all as specified and as directed. 59 Material and labour for Forming construction joint 30mm deep x 10mm wide and filled with sealing compound grade A complete all as specified and as directed. 60 Excavation in post holes (or similar holes) each not exceeding0.5 cum and getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n exc 25cm, watering and removing surplus soil to a distance n exc 50m and making good surface in soft/loose soil complete all as specified and directed. 61 Material and Labour for Plain Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate as in sub base/foundations filling and mass concretecomplete all as specified and as directed. 62 Supply and fix structural steel work in tubular trusses including special shaped washer of 6mm thick MS sheeting etc complete using ERW or induction butt welded tubes conforming to IS - 1161-1979 grade St.-240,all as specified and as directed. 63 S&F prepainted galvalume aluminium zinc coating GI based corrugated steelsheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof coveringin roof covering /cladding to wall,fixed withself tapping screws including providing of rubber washer/Bitumen washer with filling of Bitumen between joint of sheet and Self tapping screws complete all as specified. 64 S&F prepainted galvalume aluminium zinc coating GI based plainsteelsheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof coveringin roof covering /cladding to wall,fixed withself tapping screws including providing of rubber washer/Bitumen washer with filling of Bitumen between joint of sheet and Self tapping screws complete all as specified. 65 Supply and fix mild plate(plain or chequerred), channel, square cut or notched(ordinary or counter sunk) forming holes with riveted, bolted or welded attachment to bottom of pipe conforming to Fe 410-W quality A(Gde-E-250) complete all as specified and directed. 66 Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting outin soft/loose soil complete all as specified and as directed. 67 Material and labour formachine pressed precast concrete interlocking paver block, any shape and size of 60mm thickness M-35 grade conforming to IS 15658-2006 with grey cement and pigment laid over and including 50mm thick river sand cushioning, compacted with mechanical surface vibrator and with scratch proof lacquer coating on top surfaces complete all as specified and directed. 68 Material and labour forproviding cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate cast in situ asin kerbs or mud stops, rounded or chamfered on edges, as directed including use of form work as necessary all as specified and as directed. 69 Material and Labour for PCC 1:3:6, type C-2 as in concrete bed to drain pipes including packing under and completely surrounding pipes after they are laid and tested for 150mm diapipe and testedcomplete all as specified and as directed. 70 Supply and laying Reinforced cement concrete hume pipes class NP3, laid and jointed complete with one collar per length of pipe, dia 150 mm complete all as specified and as directed. 71 Materialand Labour forplain cement concrete 1:2:4 type B1 using 20mm graded granite stone aggrgate as in in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed platesand the like including weathering, slightly rounded or chamfered angles and throatingincluding use of necessary form work all as specified and as directed. 72 Material and labour for 15 mm thick renderingon brick/concrete surfaces in two layers in CM 1:4, finishing coat of 5mm thick using water proofing compound @3% by weight of cement, finished even and smooth without using extra cement complete all as specified and as directed.Note: Water proofing compound shall be measured separately. 73 Supply only integral water proofing compound all as specified and as directed. 74 Material and labour for Precast reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregateas in cover slabs of man holes including necessary form work, placed in position, set in CM 1:4 complete all specified and as directed. 75 Construction of LLDPE Septic tanks for 30 users, conventional type, excavation in ordinary soil, PCC 1:4:8 below foundation Vent shaft, connection etc. complete all as specified and directed by Engineer-in-charge.NoteThe rate quoted shall be inclusive ofinlet and outlet pipe. 76 Excavation over areas n. exc 1.5 m deep and getting out in soft/loose soil complete all as specified and as directed. 77 Excavation over areasexc 1.5 m depth and n. exc 3.0 m deep and getting out in soft/loose soil complete all as specified and as directed. 78 Material and labour for Loose filling with broken stone aggregates of gauge 40 to 80 mm in soakage pits, soakage wells, etc complete all as specified and as directed. 79 M & L for point wiring using 1.5 Sqmm lSI marked 1.1 KV grade single core FR LS flexible cable, conforming to IS: 694-1990, having multi-drawn thin strands of electrolytic copper conductors, conforming to IS: 8130-1984 and insulation conforming to IS:5831-1984, for phase, neutral and earth continuity conductor connecting to earth dolly, drawn in and including not less than 20 mm NB PVC medium grade conduits (concealed), conforming to IS: 9537 (Part 3)- 1983, colour coded as specified in IS: 11353-1985, including factory made sunken, galvanized, not less than 1.00 mm thick modular flush sheet metal enclosure having top, bottom, side and back-wall knockout for conduit entry from any direction, conforming to IS: 14772- 2000 and suitable for modular cover-plates complete all as specified in IS: 732-1989 and directedfor the following:-. Note: Circuit wire from DB to switch boards shall be included in the quoted rate. No additional payment will be paid to the contractor for the circuit submain. 80 (a ) onelight point controlled by one switch 5 Amps 81 (b) One 3pin socket outlet 5 Ampsonsame board 82 (c) one 3pin socket outlet 5 Ampspoint controlled by one switch on Independent board. 83 M & L for point wiring using 2.5 Sqmm lSI marked 1.1 KV grade single core FR LS flexible cable, conforming to IS: 694-1990, having multi-drawn thin strands of electrolytic copper conductors, conforming to IS: 8130-1984 and insulation conforming to IS:5831-1984, for phase, neutral and earth continuity conductor connecting to earth dolly, drawn in and including not less than 20 mm NB PVC medium grade conduits (concealed), conforming to IS: 9537 (Part 3)- 1983, colour coded as specified in IS: 11353-1985, including factory made sunken, galvanized, not less than 1.00 mm thick modular flush sheet metal enclosure having top, bottom, side and back-wall knockout for conduit entry from any direction, conforming to IS: 14772- 2000 and suitable for modular cover-plates complete all as specified in IS: 732-1989 and directedfor 6 pin switch socket outlet 15 Amp on independent board complete all as specified and directed by Engineer in charge:-. Note: Circuit wire from DB to switch boards shall be included in the quoted rate. No additional payment will be paid to the contractor for the circuit submain. 84 Supply and fixSwitch piano flush type 5 amps single pole, one way, 240 Volts complete all as specified and as directed. 85 Supply and fix Ceiling rose in poly carbonate 3 plates flush type 6 Amps, 250 volts AC complete all as specified and directed. 86 Supply and Fix socket outlet 5 pin,6 Amps andAC 230 volts flush type complete all as specified and as directed. 87 Supply & fix switch socket combination outlet, 6 pin, 6 Amps, multipurpose, flush, non shutter, non inter locking type, 230 volt flushtype, white/ivory finish with fixing hole complete all as specified and directed by Engineer in charge. 88 Supply & fix switch socket combination, 6 pin, 15/16Amps, multipurpose , flush, shutter type, 230 volt flushtype, white/ivory finish with fixing hole complete all as specified and directed by Engineer in charge. 89 Supply and fixing 20W LED pride plus NXT Batten 6500k,220V, White, Decorative ultra slim round profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. all as specified and as directed. Make-Havells Model No. LHEXAWP7IN1W020 or equivalent in Philips/Bajaj/Crompton. 90 Supply and fixing 10W LED pride plus Neo Batten 6500k, White, small,B22 lights fitting , 220V, Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient,connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make-Havells Model No. LHEXACP7IN1W010 or equivalent in Philips/Bajaj/Crompton. 91 Supply and fixing LED mirror lights with 09 Watts LED including electronic driver complete all as specified and directed. Make- Luker Model No. LM3C9 or equivalent in Philips/Bajaj/Crompton /Havells. 92 Supply and fixing LED light fitting 35 watt street light for building security lights, 230 Volts, outdoor type & Wide temperature operating range: -10 °C to +50 °C, with best in class design & roubst heat sink for better heat dissipation, electronic driver unit with IP 65/66 protection,lamp bracket with impact and corrosion resistant including two coat of silver coloured Mild steel angled pipe of suitable size for fixing of security light, necessary mounting bolts, nuts and washers, fixing on iron angle complete all as specified and directed by Engr-in-charge.Make: Crompton/Philips/Bajaj/Havells. 93 Material and labour for Sub main wiring using two runs of single corePVC insulated cable (FR) 6 sqmm copper conductor multi stranded and one run of 6 sqmm copper conductor insulated cable (FR)using as earth wire drawn through and including suitable size PVC Casing and Caping including taking down old aluminium/CopperSub main wirng complete all as specified and directed. Note-3 run of 6 sqmm PVC copper wire and One run of PVC casing caping shall be measured and paid as oneunit. 94 Supply and fix Distribution board (DB) made out of sheet metal enclosure (CRCA sheet), dust and vermin proof, SPN 4 way with 200 Amps rated copper bus bar double doorprotection, neutral bar,earth bar, single pole and neutral 240 volts, MCBs used as incommer flush to wall complete all as specified and as directed. 95 Supply and fix Distribution board (DB) made out of sheet metal enclosure (CRCA sheet), dust and vermin proof, SPN 8 way with 200 Amps rated copper bus bar double doorprotection, neutral bar,earth bar, single pole and neutral 240 volts, MCBs used as incommer flush to wall complete all as specified and as directed. 96 Supply and fix Distribution board (DB) made out of sheet metal enclosure (CRCA sheet), dust and vermin proof, TPN 8 way with 200 Amps rated copper bus bar double doorprotection, neutral bar,earth bar, triple pole and neutral 415 volts,MCBs used as incommer Double door, flush to wall complete all as specified and as directed. 97 Supply and fix MCB SP 6-32 amp rating 240V, 10KA B curve miniature circuit breaker (MCB) of single pole in the MCB DB,IP 20 transparent lebel holder fully insulated safety shutters suitable for cable up to 35 Sqmm cross sectional area complete including suitable size copper Lugs complete all as specified and directed.Make: Indo Asian/ L&T/Crompton Greaves/Havells 98 Supply and fix MCB SPN 32 amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of single pole in the MCB DB complete with connection testing and commissioning complete all as specified and directed.Make: Indo Asian/ L&T/Crompton Greaves/Havells 99 Supply only MCB TPN 415 Volts, 50Hz, 3 phase of capacity 40 Amps to 100 Amps, C curve 10 KA breaking capacity, IP 20 transparent lebel holder fully insulated safety shutters completeincluding suitable sizecopper lugs complete fixed properly in DB and connecting/testing complete all as specified and as directed.Make: Indo Asian/ L&T/Crompton Greaves/Havells 100 Supply and fix Exhaust Fan of size 300 mm sweep with louvers, with metal body AC 230 V, 50 Hz, 1200 RPMand connecting to ceiling rose terminals with 23/.0076 flexible cable, complete all specified and directed. Make:Havells/ Usha/Crompton Greaves. 101 Supply and fix ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep min air delivery 210 CFM service value 6.00 BEE. Five Star rated with brushless direc current motor (BLDC) complete all as specified and as directed. 102 Supply, laying or passing through pipe XLPE insulated, galvanised steel stripor wire armoured electric power cable (heavy duty) with stranded aluminium conductor 1100 Volts grade of size 4 Sqmm 2 core complete all as specified and directed. 103 Supply, laying or passing through pipe XLPE insulated, galvanised steel stripor wire armoured electric power cable (heavy duty) with stranded aluminium conductor 1100 Volts grade of size 6 Sqmm 2 core complete all as specified and directed. 104 Supply and Fix High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in trenches 40 mm bore with all acessoires for cable protection, complete all as specified and as directed. 105 Supply, fixing, laying & testing galvanised iron water tubing of 25 mm dia, medium grade, ISI marked with and including all GI fittings such asunions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. laid intrenches/floor, complete all as specified and directed 106 Supply, fixing, laying & testing galvanised iron water tubing of 32 mm dia, medium grade, ISI marked with and including all GI fittings such asunions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. laid intrenches/floor, complete all as specified and directed 107 M&L for earthing complete with Galvanised steel earth plate electrode of size 600mmx600mmx6mm, buried directly in ground (earth pit not less than 2.25 Mtr deep below normal ground level) with top edge of earth plate not less than 1.5 Mtrs deep below normal ground level, connected to GI earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI or steel and connected to earthing test point / distribution board/equipments or any other indicated situation all as shown in electrical plate No. 3 of SSR Part I (2009) and testing on completion including necessary excavation and earth work in any type of soil, returning filling, removing of soil. GI medium grade pipe 20mm dia 1.5 mtr long with funnel and wire mesh as watering pipe, and GI medium grade pipe 32mm dia as earth lead protection pipe. Earth pit chamber made of PCC 1:2:4 type B1 using 20mm graded stone aggregate including 100mm thick chamber cover made of 1:2:4 type B1 using 20mm graded stone aggregate and reinforced with 8 mm dia TMT bars at 150mm c/c on both ways precast chamber cover with lifting handle 10mm dia round bars, GI pipe medium grade 20 mm dia for earth strip protection including charcoal and common salt in alternate layer of 15cm thick covering all faces of earth electrode plate, , complete all as specified and directed. 108 Notes for Item No 104:Quoted rates shall be deemed to be included the following (a) Excavation ,RFR earth workin any type of soil. (b) PCC pit in cement concrete 1:2:4 type B-1, pre cast RCC cover40 mm thick in PCC 1:2:4type B-1, with suitable handle reinforced with welded steel wire fabric weighing not less than 1.87 kg/sqm.(c) funnelwith wire mesh , watering pipe of GI 20 mm nominal bore light grade and lugs etc. complete all as specified & directed. (d) 15 mm nominal bore medium grade GI protection pipe 7.5 meter long for protection of earthing lead complete all as specified & directed. (e) Requisite quantity of common salt and charcoal in alternative layers as specified. (f) The rates quoted for the complete earthing shall deemed to include the cost of GI wire 4.00 mm dia and GI medium grade protection pipe upto 7.5 Mtrs.(g) GI earth strip and GI medium grade protection pipe beyond 7.5 Mtrs length shall be measured and paid separately. 109 Supply, fixing, laying & testing galvanised iron water tubing of 40 mm dia, medium grade, ISI marked with and including all GI fittings such asunions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. laid intrenches/floor, complete all as specified and directed 110 M&L for Cutting existing CI/GI/DI water supply line with the help of electric cutting tools or manually, reducing to required length before laying and blockage removal, cleaning of particular joint etc and making good after repairing ofsize upto 100mm including leakage testing all as specified and as directed by Engineer-in-Charge 111 Supply and fix Gun metal, globe or gate valves 25mm, with iron wheel head, screwed both ends for iron pipe and fixedcomplete all as specified and as directed. 112 Supply and fix gunmetal gate or globe valve with iron wheel head screwed both ends for iron pipe 40 mm bore complete all as specified and as directed. 113 Supply and fix Rotational moulded Polyetheylene Water Storage Tank 500 Ltr capacity Triple Layer (Cylinderical verticle with closed top) including 20mm dia GI Medium Grade 450mm long overflow and wash out pipe each with all required fittings, Checknut, Stopper etc complete hoisted and fixed in position, including all incoming and outgoing connection of GI pipe complete and including 25mm PTMT Ball valves high pressure wiith epoxy coated aluminium rodand high density plastic ball screwed for iron pipe complete for 20mm dia pipe fixed on roof top complete all as specified and directed. 114 Supply and fix brass ball valve 25mm dia high pressure with brass rod, screwed with polythene float and fly nut complete screwed for iron pipe and fixed all as specified and as directed.Make: Sathyam/Prayag/zinith 115 Material and Labour for valve chamber of internal size 900mm x900mmx900mm using 23 cm thick brick masnory wall in CM 1:4 including excavation, earth work in any strata & PCC 1:4:8 foundation type D-2, 100 mm thick including 20 mm thick PCC 1:2:4 type B1 coping & plastering the internal surface with 10 mm thick cement mortar 1:4 providing 2mm MS sheet chamber cover with FH embossed with opening arrangementlock system with 50x50x6mm angle iron frame duly painted with two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.
