Tender For Conversion Of Lt Acsr Oh Light With Ug Cable And Connected Wk At Fsd Panitola And Provn Of Street Light With Poles For E/M Installation At Outpocket Loc Under Ge Dinjan.; 1 Excavating in trenches not exc 1.5m wide and n.exc 1.5 m in depth, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, cable trench etc and not exceeding 10 square meter on plan for manholes etc and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and directed. 2 Excavating in trenches n exc 1.5m wide and exc 1.5m but n exc 3m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed. 3 Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed. 4 Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level nexc. 1.5 metre above the starting point complete all as specified and directed. 5 M&L for clear sand cushioning with dry clean sand for protection of cable,15cm below the cable and 8cm above the cable, complete all as specified and as directed. Note : Punned thickness shall be measured for payments. 6 Supply and laying unreinforced precast concrete cable cover class LV, type 1, flat size 250 x 150 x 40 mm for cable protection, complete all as specified and as directed. 7 Supply and laying well burnt bricks sub class ‘B’ bricks laid width wise along length of cable in trenches for cable protection laid for UG cable protection all as specified as directed. 8 Boring of holes horizontal for laying not less than 80/50/40/32mm pipe (minimum depth 0.75 mtr from top level) under the road pavement, hard standing using trenchless technology complete all as specified and as directed.Note : cost of accessories required for making hole/bore deemed to be included in the quoted rate. 9 S&F RCC cable route indicator with embrossing mark as LT cable, of size75 cm x 15cm x 7.5cm complete all as specified and directed. 10 Supply, laying, jointing, commissioning and testing cross-linked polyethylene (XLPE) insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volt grade with stranded aluminium conductor of size 150 sq.mm 3.5 Core, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items.(2) Excavation and earth work shall be measured and paid separately.complate all as specified and directed. 11 All as per item No. 10 here in before but of size 120 sq.mm 3.5 Core. 12 All as per item No. 10 here in before but of size 95 sq.mm 3.5 Core. 13 All as per item No. 10 here in before but of size 70 sq.mm 3.5 Core. 14 All as per item No. 10 here in before but of size 50 sq.mm 3.5 Core. 15 All as per item No. 10 here in before but of size 35 sq.mm 3.5 Core. 16 All as per item No. 10 here in before but of size 25 sq.mm 3.5 Core. 17 All as per item No. 10 here in before but of size 16 sq.mm 4 core. 18 All as per item No. 10 here in before but of size 16 sq.mm 2 core. 19 All as per item No. 10 here in before but of size 10 sq.mm 4 core. 20 All as per item No. 10 here in before but of size 10 sq.mm 2 core. 21 M&L for GI pipe light grade with all fittings complete grouted in ground all as specified for 32mm bore of pipe laid in trenches/fixed with poles/laid in road/plinth/floor for protection of cable including taking down old unserviceable complete all as specified and directed. 22 M&L for GI pipe light grade with all fittings complete grouted in ground all as specified for 50 mm bore of pipe laid in trenches/fixed with poles/laid in road/plinth/floor for protection of cable including taking down old unserviceable complete all as specified and directed. 23 M&L for GI pipe light grade with all fittings complete grouted in ground all as specified for 80 mm bore of pipe laid in trenches/fixed with poles/laid in road/plinth/floor for protection of cable including taking down old unserviceable complete all as specified and directed. 24 M&L for GI pipe light grade with all fittings complete grouted in ground all as specified for 40 mm bore of pipe laid in trenches/fixed with poles/laid in road/plinth/floor for protection of cable including taking down old unserviceable complete all as specified and directed. 25 Dismantling/taking down old aluminium steel reinforced (ACSR) conductor of any size any type from LT overhead line including all jumper, cross arms, clamps, bolts, nuts etc and keeping serviceable materials in safe custody for reuse in the work complete all as specified and as directed 26 Dismantling cross-arms of M.S. channel or angle sections etc. complete and stackingaside serviceable materials for re-use with in 50m and removing unserviceable materials from site of workcomplete all as specified and as directed. 27 M&L in repair, dismantling the all cable from panel, poles, MCB Main DBs taking out the cable loop stretching out the cable, carrying out end termination with new lugs, proper thimbling, fixing the joint kits connecting back to the new/existing panel board by means of nuts, bolt & washers of any size any type complete all as specified and as directed.Note : (i) The work includes necessary excavation to take out the loop and laying the cable, putting proper cable protection bricks using the old retrieved bricks and refill the area properly and spreading any surplus soil.(ii) The cost of AI lugs, joint kit shall be measured and paid separately under relevant items of schedule. 28 Supply, jointing and testing XLPE cable straight through joints including jointing materials and accessories complete, hot shrinkable outdoor cable joint kit suitable for XLPE 1100 Volts (Earthed) cable of size 70 Sqmm to 150 Sqmm 3.5/4 Core complete all as specified and as directed.Note : Excavation and earth work shall be measured and paid separately. 29 Supply, jointing and testing XLPE cable straight through joints including jointing materials and accessories complete, heat shrinkable outdoor cable joint kit suitable for XLPE 1100 Volts (Earthed) cable of size 25 Sqmm to 50 Sqmm 2/3.5/4 Core complete all as specified and as directed.Note : Excavation and earth work shall be measured and paid separately. 30 Supply, jointing and testing XLPE cable straight through joints including jointing materials and accessories complete, hot shrinkable outdoor cable joint kit suitable for XLPE 1100 Volts (Earthed) cable of size 6 Sqmm to 16 Sqmm 2/3.5/4 Core complete all as specified and as directed.Note : Excavation and earth work shall be measured and paid separately. 31 S&F new PVC cable Junction Box IP66 halogen free and weather proof for out door installation sizenot less than 200 x 150 x 100 mm suitable for street light incoming and outgoing cables up to 10 to 25 sqmm 4 core (with terminal) & inclusive of MCB SP 10 Amp, 60A 04 strip aluminium Bus Bar, including nuts,bolts,cable glands & MS clamps fixed to pole allas directed. 32 Supply, laying & testing PVC insulated, PVC sheathed cable galvanized steel strip or wire unarmoured, electric control cables (Heavy duty) with stranded Aluminium conductor of size 1.5 sq mm ,2 core, 1100 Volts grade passed throuh PVC conduit medium grade of size Min 20mm complete all as specified and directed. 33 M&L Earthing complete with Galvanised steel earth plate 60cmx60cmx6mm thick electrode, buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 m below ground level , connected to GI earth strip 25 X 4mm up to test point by means of bolts ,nuts , check nuts and washers of GI including excavation and earth work, PCC 1:3:6 type C-1 pit, 20mm dia GI pipe medium grade, watering pipe and 20 mm bore GI pipe, light grade for protection of earth strip, MS angle iron frame 40x40x3mm, 10mm thick RCC 1:2:4 type B-1 cover reinforced with 6mm dia MS bars @ 75mm C/C both ways and with MS handle made out of 12mm dia bars, PGI Funnel, wire mesh etc complete all as shown in electrical Plate No 03 of SSR Part-I and connected to earthing test point all as specified or indicated including testing on completion complete and including taking down old u/s. 34 Supply installation, commissioning and testing including providing all necessary electrical connection, LT feeder panel board of size 1.2x1.2x0.6 m Outdoor type double door, factory made out of 3.15 mm thick MS sheethaving hinge opening arrangement in front and back side and bottom frame made out of angle of size 50 x 50 x 6mm thick and 04 Nos legs 0.6 meter length with cable entry and exist circular hole with cable gland & gasket at bottom complete including painting to all internal and external exposed steel surfaces with power coating paint ( 5 stage process) with duly fixed in ground with necessary PC foundation (1:2:4) type B1, with danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled (white), with letters, figures and conventional skull and bones in signal red colour, fixing lugs/glands for incoming and out going cables , bolts , screws ete complete all as specified and directed by Engr-in-charge and comprising of the following accessories.(Note : All the internal connection connectedthrough suitable size of copper bus bar)..(a) Aluminum bus bar of suitable size for 400 Amp (TPN) including insulator.(b) 250 Amp, 4 Pole MCCB , 50 Hz ,415 V with rupturing capacity 50 KA - 01 No. (In coming).(c) Indicator lamp LED type (set of three Red, Yellow, Blue)----01 Nos.(d)Digital Multifunction meter, Model C, class 1, with relay - 01 No. Make AE/L&T/ABB/HPL.(e)63 Amp, 4 Pole MCCB , 50 Hz ,415 V with rupturing capacity 36 KA - 06 No. 35 Supply, install,testingand commissioning outdoor type LT panel of size 1.2m x 1.2m x 0.6m , factory made totally encloseddust and vermin proof , double steef shutter in front and single leaf shutter in rear side made of 3.15 mm thick CRCA sheet, duly fabricated and having proper locking arrangement in both ront and rear door painted with powder coated paint and Aluminium bus bar 250 amps suitable for 500 volts, 50 Hz , 3 phase 4 wire system and comprising with and including following accesories and mounted on PCC platform all around the panel board complete with the following items:- (Main Panel NO-I) Family QtrsNote : Foundation to be included in the quoted priceIncoming :-(a)MCCB, 4 Pole,160A, 415 V, 25 kA. (I/C). Fixed Thermal Magnetic release(b)3 Phase LED Voltmeter Cl-1 (c) Phase indicator lamps (RYB) -set of 3 (d) Aluminium bus bar 4 strip - 250 amps(e)Internal connection by Aluminium strip from mcb/mccb to busbar and busbar to mccb/mcb etc Outgoing :- (a) MCCB, 4 Pole, 100 A, 415 V 25 kA - 03 nos (c) MCB,TPN, 63A, 240 V, 16 kA- 02 Nos. (For street light and 01 extra) 36 Supply, install,testingand commissioning outdoor type LT panel of size 1.2m x 1.2m x 0.6m ,factory made totally encloseddust and vermin proof , double steef shutter in front and single leaf shutter in rear side made of 3.15 mm thick CRCA sheet, duly fabricated and having proper locking arrangement in both ront and rear door painted with powder coated paint and Aluminium bus bar 400 amps suitable for 500 volts, 50 Hz , 3 phase 4 wire system and comprising with and including following accesories and mounted on PCC platform all around the panel board complete with the following items:- (Main Panel NO-I) unit area.Note : Foundation to be included in the quoted priceIncoming :-(a)MCCB, 4 Pole, 250 Amp,415 V, 50 kA - 01 No (b)3 Phase LED Voltmeter Cl-1(c) Phase indicator lamps (RYB) -set of 3(d) Aluminium bus bar 4 strip - 400 amps(e)Internal connection by Aluminium strip from mcb/mccb to busbar and busbar to mccb/mcb etcOutgoing :- (a) MCCB, 4 Pole,160Amp,415 V, 36 kA - 03 No (b) MCB,TPN, 63A, 240 V, 16 kA- 02 Nos. (For street light and 01 extra) 37 Supply, install,testingand commissioning outdoor type LT panel of size 1m x 1m x 0.5m , factory made totally encloseddust and vermin proof , double steef shutter in front and single leaf shutter in rear side made of 3.15 mm thick CRCA sheet, duly fabricated and having proper locking arrangement in both ront and rear door painted with powder coated paint and Aluminium bus bar 200 amps suitable for 500 volts, 50 Hz , 3 phase 4 wire system and comprising with and including following accesories and mounted on PCC platform all around the panel board complete with the following items:- (FP -1,2,3,5).Note : Foundation to be included in the quoted priceIncoming :-(a) MCCB, 4 Pole, 125A, 415 V, 36 kA. (I/C).(b) Phase indicator lamps (RYB) -set of 3(c) Aluminium bus bar 4 strip -200 amps(d)Internal connection by Aluminium strip from mcb/mccb to busbar and busbar to mccb/mcb etcOutgoing :-(a) MCCB, 4 Pole, 100 Amp,415 V, 36 kA - 01 No (b) MCB, TPN, 63 A, 240 V, 16 kA- 05 No. 38 Supply, install,testingand commissioning outdoor type LT panel of size 1m x 1m x 0.5m, factory made totally encloseddust and vermin proof , double steef shutter in front and single leaf shutter in rear side made of 3.15 mm thick CRCA sheet, duly fabricated and having proper locking arrangement in both ront and rear door painted with powder coated paint and Aluminium bus bar 150 amps suitable for 500 volts, 50 Hz , 3 phase 4 wire system and comprising with and including following accesories and mounted on PCC platform all around the panel board complete with the following items:- (FP -4,7) for unit area (FP-1, FP 2, FP 3 for family qtrs)Note : Foundation to be included in the quoted priceIncoming :-(a) MCCB, 4 Pole, 100A, 415 V, 30 kA.- 01 No.(b) Phase indicator lamps (RYB) -set of 3 (c) Aluminium bus bar 4 strip -150 Amps (d)Internal connection by Aluminium strip from mcb/mccb to busbar and busbar to mccb/mcb etc Outgoing :- (a) MCB, TPN, 63 A, 240 V, 16 kA- 05 No. 39 Supply, install,testingand commissioning outdoor type LT panel of size .6m x 0.6m x 0.5m , factory made totally encloseddust and vermin proof , double steef shutter in front and single leaf shutter in rear side made of 3.15 mm thick CRCA sheet, duly fabricated and having proper locking arrangement in both front and rear door painted with powder coated paint and Aluminium bus bar 200 amps suitable for 500 volts, 50 Hz , 3 phase 4 wire system and comprising with and including following accesories and mounted on PCC platform all around the panel board complete with the following items:- (Bus Bar Panel).(a)Aluminium bus bar 4 strip of 200 Amps having hole drilled on Bus Bar for fixing of cables. Note : Foundation to be included in the quoted price 40 Supply, install, testing and commissioning of dual nature switch smart timer based Each automatic street light control panel, the panel should be suitable for 3 phase 15 kw power Job load. the control panel should be maintenance free in design and setting accessible via mobile app (with Bluetooth connectivity), the mobile app should be allowing users to (customize the ON & OFF timing based on Natural light lux level sensor or local sunset/sunrise (astro) or manual time setting or combination of all options), the mobile app should also have facility to set input voltage range. the control panel have 2 smart timers along with suitable power contactors and incoming -outing MCBs should be enclosed in a pole/ wall mountable rust proof, electric shock proof, termite proof and FR grade SMC enclosure conforming to IP66 and circuit should also have provision for manual operation (i.e. sensor by pass option & controlling current phase selection option at least from 2 phase). Note: the hanging arrangement on pole/wall to be included in the quoted price 41 Materials and labour plain cement concrete Type B1 1:2:4 (using 20mm graded stone aggregates) as copings of pole, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering,slightly rounded or chamfered angles and throating, as directed inclusive of necessary form work complete all as specified and directed. 42 Materials and Labour for plain cement concrete (1:4:8) type D-2,using 40mm graded stone aggregate as in foundations of stay assembly, poles, strut etc complete all as specified and as directed. 43 Dismantling of insulators of any type from LT poles of any size and type and setting aside complete all as specified and as directed. 44 Dismantling of GI earth wire 4.0mm or any size complete all as specified and as directed. 45 S&F steel tubular swaged poles complete with cast iron base plate, final taper plug, botls, nuts and screws as specified type C/10 SP 22 (8.5 meter long). Painted with silver paint and yellow block strip at the bottom complete all as specified and directed. 46 Supply, Installation, testing and commissioning of 60W All-In-One LED Solar Streetlights made up of Aluminium Extrusion housing with minimum 150Wp Monocrystalline Panel fixed on the top side of luminaire housing (Battery, charge controller and LED module should be integrated inside Luminaire). Maintenance free 12.8V/60Ah LiFePo4 battery along with BMS (BIS certification required)with minimum cycle life of 2000 cycles, MPPT Charge controller with Efficiency > 90%. Luminaire should be IP65 & IK08 and have lumen output of greater than 10000 lumens at full power (System Efficacy > 170 Lumens/watt) as LM79. The LED chip used should be of Osram, Lumileds, Cree, nischia only with CRI>70 and CCT – 5700K +/- 500K and should be with lenses for effective light distribution. Solar Panel, MPPT charge controller, and luminaires should of Same make and Light fixture along with MPPT controller should be manufactured in in-house manufacturing facility only. The solar lighting company must have inhouse NABL accredited lab with scopeas per ISO17025:2017 to include for testingSafety and Performance Standards for LED Lamps, LED Modules, LED Drivers, Luminaires and Photometry parameters as per LM79:2019 and IES TM30-18 standards . Luminaire must have Green & Red indicator lights for showing charging of battery and low battery voltage respectively. Light fixture must also have protections like Over-Charge protection, Deep-discharge protection,current protection , Short circuit protection , Over voltage protection. The light fixture should come with a PIR sensor for auto dimming of light fixture based on movement and Complete system should be designed to provide 2 days (24 hours) backup in dimming mode. The light fixture should also come with hybrid controller so that light fixture works on AC power if the battery goes down in case of adverse weather conditions. the solar light suitable for side mounting on pole. The solar lighting companies must have toll free base service network to provide immediate after sales service networks available in different districts of the state. Certificates to be submitted – • LM79• LM80• BIS certificate of Battery • BIS certificate of Solar Panel• IK08 and IP65 certificate Note : Cost of T&P, mounting fixture required to install as per site requirement should be included in quoted rate of this item only. No extra payment will be given for mounting fixture.
