Tender For Repair To Hard standing Drainage, Fencing, Path Etc And Connected Itmes At Kaluchak Mil Station Under Ge Kaluchak; 1 Demolition of brick work or stone / bouldermasonry includingall quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed. 2 M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:4 complete all as specified and directed. 3 M & L for brick work with sub class ‘B’ old size bricks (EXCEPTBRICKS) straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed. NOTE: - OLD BRICKSOBTAINED FROM DEMOLITION SHALL BE USED UNDER THIS ITEM. 4 Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation etc. or for laying of cable/GI pipe/concrete pipe etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed. 5 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed. 6 Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed. 7 Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key,scrubbing down with water etc, completeall as specified and directed. 8 M & L for Rendering 15mm thickfair faces of brick / concrete surfacesin cement mortar1:4finished even and smooth with out usingextra cement completeall as specified and directed. 9 M & L for preparation of newly plastered or un-plastered surfaces of ceiling and applyingtwo coats of cement base paint complete all as specified and directed. 10 M & L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed. 11 S & F of 300 mm bore reinforced concrete pipe class NP-3 laid, jointed with collar in neat cement slurry complete all as specified and directed. 12 M & L for cement concrete 1:4:8, type C-2 (using 40 mm graded stone aggregate) as in bed to drain pipes of 300 mm bore including packing under and haunching against the sides of pipeafter they are laid and tested complete all as specified and directed. 13 Dismantling of fencing wire mesh,any type complete all as specified and directed. 14 Dismantling posts or struts (wood, steel or R.C.C.) anysection, including taking out embedded portion and making good disturbed ground complete all as specified and directed. 15 Excavation in post holes (or similar holes) each not exc. 0.50 Cum, getting out, returning, filling and ramming earth or broken rubble mixed with earth around in layers not exc. 25 cm watering and removing surplus soil to a distance not exc. 50 m and making good surface as in hard / dense soil complete all as specified and directed. 16 S&F angle iron fencing post, struts & flat iron straps to chain link fencing including cutting tops to shape as directed, drilling holes, notching or wire etc, flat iron fillets (for seruring wore mesh etc) including all necessary drilling, bolting or riveting etc and similar work confirming to Fe-410-0 or Fe 310-0 any size all as specified and directed. 17 S & F of mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other or screwed both ends, each screwed ends to be fitted with washer and one hexagonal or square nut,length of bolt exc 10cm and n exc 15cm long and 11 to 15 mm dia of neck complete all as specified and directed. 18 Supply only Chain link MS galvanisd fencing, any size or type weight n. exc 4.00 kg per sqm complete all as specified and directed. 19 Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed. 20 Dismantling of old rusted galvanised barbed wire/concertina coil of any size & type in any position, complete all as specified & directed. 21 S & F of galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, straining bolts at ends, staples or steel pins etc. complete all as specified and directed. 22 M & L for Barbed razor tape concertina coil SG hot galvanised spring tensile wire as approved by GE, dia of coil when stretched 450mm having minimum number of circles 10 Per RM, minimum number of clips 15/RM, complete all as specified & directed. 23 M & L for preparation of steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. 24 M & L for preparation of steel surfaces over n.exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. 25 S & F of rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other covering doors etc. to be prepared for hanging orsteel hanging door fitting and also fastening complete all as specified and directed. 26 S & F of 1.60 mm thick mild steel plain black sheet in wall cladding, steel gate and similar work, cut to size, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted and welded seams as required including bending or turning up, mitred angles etc. as required complete all as specified and directed. 27 M & L for mild steel round bars 10 mm dia and over, confirming to Fe-410-W (Grade E-250) cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia securing with clips complete all as specified and directed. 28 Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed. 29 M & L for providing plain cement concrete, type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed. 30 M & L for providing plain cementconcrete type B-1, 1:2:4, (using 20 mm graded stone aggregate), as incopings, bed plates, kerbs levelling courses etc, complete all as specified & directed.. 31 M & L for Factory made precast chequrered cement desiner paver tiles of different colour and shape of zone (300 x 300 x 20) mmm laid and jointed with grey cement slurry with Pigment to match the colour of tile, compressive strength not less than 250 Kg/Sqm including 15mm thick screed bed in cement mortar 1:4 complete all as specified & directed. 32 M&L for Dura stone external designer floor tiles, any colour, shape and size not less than (300 x 300)mm 9-10mm thick M-25 grade, set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed. 33 M&L precast kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve hall not to more than 5mm), including making drainage opening wherever required completed. 34 Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. 35 M & L for 100mm thick cement concrete 1:4:8 type D-2, using 40 mm graded stone aggregateas laid in laid in floorfinishes without using extra cement complete all as specified and directed. 36 M & L for 75 mm thick PCC 1:3:6, nominal mix, type C2, using 40mm graded crushed stone aggregate as in sub base of floor, hard standing, path, pavings etc, surface finished even and smooth without using extra cement, laid in alternate bays,complete all as specified & directed.. 37 M & L for 40mm thick cement concrete 1:2:4 type B-1, using 20 mm graded stone aggregate as laid in floors,surfacefinished even and smooth using extra cement, laid in alternate bays, complete all as specified and directed.
