|
| 1 | Labour charges for replacement of spares for Pressure Booster pump GT-H-24V of Make Grundfos after disconnecting the inlet and outlet CPVC/GI pipes and reconnecting the same after completion of repairs, setting the required pressure, including replacement of U/s bushes, washers, nuts, bolts, riviting if necessary, any other minor accessories etc and testingcomplete all as specified and directed.Note: All major spare parts required are measured and paid under relevent item of this BOQ. |
| 2 | KP 35 Pressure Switches |
| 3 | Seal Kit for CM1/35 Module. |
| 4 | Pressure Release 24 Ltr Tank GT-H-24 PN10 |
| 5 | High Speed Motor Re-winding replacement |
| 6 | Disconnecting electric/water connections and removing Electric motor / pumpset from base plate and transporting to workshop and back after repair, servicing etc and refixing in it\"s original position, including replacement of U/s bushes, washers, nuts, bolts, riviting if necessary, any other minor accessories etc testing and commissioning complete all as specified and as directed for the following capacity :-Note: all major spares required are measured and paid under relevent item of this BOQ |
| 7 | 20 HP 3 phase |
| 8 | 10 to 12.5 HP 3 phase |
| 9 | 5 to 7.5 HP 3 phase |
| 10 | 3 to 0.5 HP 1 phase |
| 11 | M & L for rewinding of induction motor by means of cutting and removing existing burnt out winding completely, cleaning and repair of slots and rewinding with new copper wire of existing gauge and size/turns, varnishing with class B insulation, assembling the motor complete, testing at workshop complete all as specified and directed for the following capacity :- |
| 12 | 20 HP 3 phase |
| 13 | 10 to 12.5 HP 3 phase |
| 14 | 5 to 7.5 HP 3 phase |
| 15 | 3 HP 1 phase |
| 16 | 2 HP 1 phase |
| 17 | 1 HP 1 phase |
| 18 | 0.5 HP 1 phase |
| 19 | S & F in repairs all ball/roller bearings in centrifugal/ monoblock motor and pump of following capacity after taking out broken/wear & tear unserviceable bearing complete all as specified and directed for the following :- |
| 20 | 20 HP 3 phase |
| 21 | 10 to 12.5 HP 3 phase |
| 22 | 5 to 7.5 HP 3 phase |
| 23 | 2 to 3 HP 1 phase |
| 24 | 0.5 to 1 HP 1 phase |
| 25 | S & F in repairs stainless steel shaft for centrifugal pump of following capacity including rotar assembly after taking out broken/wear & tear/ unserviceable shaft as per the sample & existing type & size complete all as specified and directed for the following :- |
| 26 | 20 HP 3 phase |
| 27 | 10 to 12.5 HP 3 phase |
| 28 | 5 to 7.5 HP 3 phase |
| 29 | S & F in repairs impeller in centrifugal pump of following capacity after taking out broken/wear & tear/ unserviceable impeller as per the sample & existing size complete all as specified and directed for the following :- |
| 30 | 20 HP 3 phase |
| 31 | 10 to 12.5 HP 3 phase |
| 32 | 5 to 7.5 HP 3 phase |
| 33 | 2 HP to 3 HP 1 phase |
| 34 | 0.5 to 1 HP 1 phase |
| 35 | M & L for preparation of old painted surfaces of centrifugal pump set of following capacity and applying two coats of synthetic enamel paint over a coat of red oxide primer by using spray gun complete and writing of MES/SM No complete all as specified and as directed for the following capacity :- |
| 36 | 20 to 10 HP 3 phase |
| 37 | 5 to 7.5 HP phase |
| 38 | 2 to 3 HP 1 phase |
| 39 | 0.5 to 1 HP 1 phase |
| 40 | M & L for preparation of old painted surfaces of Motor starter panels and applying two coats of synthetic enamel paint of existing color over a coat of red oxide primer by using spray gun complete all as specified and as directed. |
| 41 | S & F in repair 100mm Bronze floot valve with Neoeren seal \"O\" ring screwed ends, after taking out old unserviceable foot valve from open well/UG sump conforming to relevant IS-4038 PN 0.2 for the following sizes complete all as specified and as directed :- |
| 42 | PVC Foot Valve of Size 40mm |
| 43 | S & F in replacement of CI sluice valve, PN 1.6, ISI marked, flanged ends and suitable holes drilled with brass spindle and check nut including rubber gasket 3mm thick nuts, bolts & washers and other necessary machine works as required at site including taking down/removing the unserviceable sluice valve complete all as specified and directed for the following sizes :- |
| 44 | CI 150mm dia |
| 45 | CI 100mm dia |
| 46 | M & L for repairs to 80/100/150mm CI sluice valves refacing, regrinding, repacking stuffing box of sluice valve spindle after cleaning and including re-assembling with 3mm thick gaskets, nuts, bolts, washers and other necessary machine works as required at site complete all as specified and as directed. |
| 47 | S & F in replacement of Fuel pipe of length not exceeding 1 feet alongwith brass end terminals suitable for 12 HP diesel engine complete all as specified and as directed. |
| 48 | M&L for shifting/transporting of motor and pump from one location to another location after taking out all water/electric connections, transporting the existing motor/pump to store, including bushes, flanges, nuts, bolts, washers etc complete all as speified and directed. |
| 49 | S&F in replacement of Gunmetal garden hydrant (pop-up sprinkler) fixed onirrigation pipe line complete, for 25mm dia including suitable size socket, cutting the old pipe and making threadding for existing GI Pipe complete all as specified and as directed. |
| 50 | M&L for repairing the existing bore upto depth of 7 mtr and clear the excess mud form the bore by earth auger method for the dia of bore 40 to 50 mm, including supply and replacing the slotted 40mm GI medium grade pipe, Strainer \"Y\" type, check valve of size 25x25mm all as directed. |
| 51 | S&F in replacement of SP 6-32 A rating 240V, 10KA \"C\" curveMCB complete with connection testing and commissioning. |
| 52 | Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 2 core, 6 sq. mm nominal cross section, stranded conductor in service connections complete all as specified and directed. |
| 53 | S&F in replacement of3 pole power contactor, AC3 rating of 32A, 415V, 50HZ, Conforms to IS/IEC 60947-4-1 & IEC 60947-4, robust and suitable for hostile applications complete all as specified and as directed. |
| 54 | S&F in replacement ofstar delta combination coil with timer suitable for20H.P motor starter with 3 pole power contactor, AC3 rating of 32A, 415V, 50HZ, complete all as specified and as directed. |
