Tender For Work Of Fabrication For The Season 2025-26 - Work Of Cutting And Removing The Old Pipe Line From 1/2 To 12 Inches And Installing New Pipe. Work Of Fabricating And Installing New Neck Band, Nipple, Cast T-Rider From 1/2 Inch To 12 Inch. Work , kaimganj-Uttar Pradesh

Tender For Work Of Fabrication for The Season 2025-26 - Work of cutting and removing the old pipe line from 1/2 to 12 inches and installing new pipe.Work of fabricating and installing new neck band, nipple, cast T-rider from 1/2 inch to 12 inch.Work of fabricating and installing new neck coils from 1/2 inch to 12 inch dia.Work of fabricating and installing new flange from 6 to 12 inch dia.Work of cutting and removing the old pipe line from 14 to 40 inches and installing new neck band, nipple, cast T-rider from 14 inch to 40 inch and installing new neck band.Work of making and installing new neck flange from 14 inch to 40 inch dia.Fabricating and installing new round square tank installed in the mill and installing all connections at their respective places.10 to 01 meter dia.Above 01 meter to 03 meters.Strengthening with heavy structure at various places.Strengthening with light structure at various places.Strengthening and repairing of neck platform at various places.Making and installing/replacing manholes at various places.Removing old/neck cone installed at various places and making new one from 8/10 mm plate and installing it. 10 to 01 meter dia.Above 01 meter to 03 meters.Work of fabricating and installing new 6/8 mm plate in the gully casing of fans at various locations.Making and installing catchers installed at various stations. (Including all attachments)Patching of corroded equipment at various stations.Work of replacing corroded trough/side plate of cane carrier/bagasse elevator/RBC.Removing gully side plate at various locations and installing new plate.Removing runner base of cane carrier/bagasse elevator/RBC and installing new runner base.Removing runner of cane carrier/bagasse elevator/RBC and installing new runner.Removing damaged T-iron and angle iron of cane carrier and straightening the crooked part and installing it again.Removing the corroded part of trough at various locations and installing new one.Chevron grooving of new rollers of the mill.Chevron grooving of old rollers of the mill.Removal of the empty partition plate of the juice box above and below the juice heater and make a new one from 10/12 mm plate and install it.Fixing ribs in the partition above and below the juice heater.Repairing the shave-all of the quad. Removing old gutters installed at various places and making new ones.Removing old seal-all installed in pan and quad and making new ones and installing them.Making new ones and installing umbrella installed inside pan and removing old one.Replacing Mascot receiving crystallizer along with ribbon arm.Making separator of A Mascot machine.Removing trough of hopper and making new ones and installing them.Making and installing separators of continuous machines.Removing tubes of Quad juice heater and dynamic juice heater and expanding them by installing new tubes and giving satisfactory trial by hydraulic tax. Size 42 mm.Removing tubes of pan and expanding them by installing new tubes and giving satisfactory trial by hydraulic tax. Size - 96 mm.Removing corroded ducting of both boilers and making ducting from new or old plate and installing it.Boiler No. Removing the street plate in front of 1 and 2 and the roof and installing a new one.Removing the damaged boiler damper and making and installing a new one.Making and installing bagasse suit.Replacing the juice overflow box of the clarifier.Making and installing wedges for motor pumps at various places as per the requirement.Replacing the 6 inch dia cooling pipe of the sulphur furnace. Making and replacing manholes at various places.Making and replacing internal parts of pan catcher.Making and replacing hood of cane cutter.Removing old bottom plate of the lowest compartment of clarifier and installing new plate on it by installing angle mesh as per instructions and giving satisfactory water trial.Making and installing new stirrer of clarifier and giving satisfactory trial.Removing shaft of A pug mill and removing old bushes from both sides and fitting new ones.Removing and repairing and re-fitting shaft of brown sugar magma mixer and fitting new bushes.Making and installing new connecting rod of hopper.Making and installing new catcher strainer.Removing old rail line of unloaders duct and fitting new rail line satisfactorily and water leveling.Fitting old rail line of unloaders bridge by turning it over and checking water level etc. Removal of old/corroded channels from height to 10 inches dia installed at various places and installation of new ones as per requirement.Cutting and straightening of old plates installed at various places as per requirement. Cutting and removing the tuff plate (with support) of the top chamber of the clarifier, melted shell and top cover plate and fitting a new plate and giving water proof trial.Making and installing a new hopper driving end. Aligning and fitting it.Making and installing the top cover of the centrifuge machine.Making and installing the arm in the shaft of the pug mill.Making and installing the jacket of the sulphur furnaces scabber/bottle.Making and installing the DM type sulphur furnace.Cutting and removing the melted save all of the vapour cell and making and installing it with a new plate.Reducing the diameter of the shell of the juice sulphiter and modifying it as per the drawing.Removing the old DSM screen and fitting a new one and fitting it with a new one.Removing the melted mixed juice spreader fitted on the mill and making and installing a new one as per instructions.Cleaning all the tubes of the dajient heater and giving hydraulic testing.Replacing and strengthening the lane plate of the unloader trolley.Cutting out the corroded juice tray of mill no. 3 and installing a new one and giving a satisfactory trial.Fixing guides on both sides of the chain near the gutter in the can carrier

INR 590 /-

Refer document