Tender For Addn/Altn To Existing Infrastructure In Lgs Section And Provn Of Covered Shed Near Bldg No P-517 Of 5 Brd
Tender Value
Ref. Documents
Estimated cost
Bid Submission
31 Jul 2025
0 days left
EMD
96600
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
sulur → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Addn/Altn To Existing Infrastructure In Lgs Section And Provn Of Covered Shed Near Bldg No P-517 Of 5 Brd Addn/Altn To Existing Infrastructure In Lgs Section And Provn Of Covered Shed Near Bldg No P-517 Of 5 Brd At Afs Sulur
BOQ
| Sl. No. | Item Description |
| 1 | SCHEDULE A BOQ |
| 2 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc., including removing debris material to out side MD land complete all as specified and directed. |
| 3 | M&L Brickwork with fly ash bricks using old size bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and as directed |
| 4 | M&L rendering 10mm th plaster in CM 1:6 on fair faces of brick or concrete surfaces finished fair and even without using extra cement complete all as specified and as directed. |
| 5 | M&L for rendering 15mm thick in CM 1:4 on brick or concrete surface,finishing even and smooth without using extra cement but using waqter proofing compound complete all as specified and directed. |
| 6 | M&L for rendering 5mm thick in CM 1:3 onconcrete surfaceof ceiling finishing even and smooth without using extra cement complete all as specified and directed. |
| 7 | M&L three coats of white wash on new plastered ceiling surface including preparation of surfaces complete all as specified and directed. |
| 8 | M&L preparing surface plastered or unplastered on wall with two coats of Cement base paint over a coat of alkali resistant primer paint with complete all as specified and directed. |
| 9 | M&L for three coat of white washing in internal wallincluding preparation of new surfaces complete all specified and as directed. |
| 10 | M&L rendering 10 mm thick in CM 1:3 , mixed with water proofing compound, on concrete surfaces of roof , surface finished even and smooth. (supply only of water proofing compound shall be measured and paid seperately) |
| 11 | M&L for cleaning the top surface of concrete and providing water proofing treatment with polymeric water proofing memberane not less than 3.0 Kg/Sqm such as M/S Tikki tar /STP/ SUPER HYDRA-310 /Equivalentof approved make test to be carried out from national test hous/Govt lab ,for all makes, including priming the surface by applying bituminous primer @ 0.3 Kg/sqm andapplying the surface by blown grade bitumen 85/25 @ 1.20 Kg/Sqm &applyingwater proofing memberane( with 10 cm. overlaps )andapplying the surface by blown grade bitumen 85/25 @ 1.20 Kg/Sqm and painting bituminuos aluminium paint @ 100gm/sqm all as specified & directed. |
| 12 | Supply only water proofing compound complete all as specified and directed. |
| 13 | M L forMoorum / Red bajri filling in floors or pavings, laid in layers n.exc15 cm thick spread levelled and rammed incl watering etcall as specified & directed. |
| 14 | M&L Hard core of gauge n.exc 63 mm, deposited, spread, levelled in layers not exc 15 cm thick, watered and well rammed to a true surface complete all as specified and directed. |
| 15 | M & L cement concrete in foundation / filling /mass concrete type D2 1:4:8 using(40 mm graded aggregate) as in sub baseetc complete all as specified and directed. |
| 16 | M&L 100mm thick with cement concrete 1:2:4 type B1 (20mm graded aggregate),in floor finished even &smoothwithout using extra cement all as specified and directed |
| 17 | M&L for cement concrete 1:3:6 type C2,75mm thick with using extra cemnet as in plinth protection complete all as specified and directed. |
| 18 | M & L Machine cut Kota stone slab flooring 20-25 mm thick laid overcement screed bedof 20 mm thick of cement mortar 1:4 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & as directed. |
| 19 | Taking down cement or cement limeplaster on brick walls etc including raking out joints, hacking for key scrubing down with water etc all as specified and directed . |
| 20 | M&L for RCC M-25 (Design mix) (using 20mm graded stone aggregate) as in Columns, pillars, piers, posts and struts, etc and mass concrete all as specified. |
| 21 | Formwork to Square,rectangular or polygonal rough surface of concreteof sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed. |
| 22 | M&L for RCC M-25 (Design mix) (using 20mm graded stone aggregate) as in beams, cantilevers, bressumers, lintels over 1.5m span etc complete all as specified and directed. |
| 23 | Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed. |
| 24 | M&L for RCC M-25 (Design mix) (using 20mm graded stone aggregate) as in Chajja complete all as specified and directed. |
| 25 | Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed |
| 26 | S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 27 | Ditto, but 5mmdia and over upto and including 10mm dia in stirrups,spacer and binders complete all as specified and directed. |
| 28 | M & Lfor Forming 12 mm thick and 150 mm deepexpansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘B’ ® complete all as specified and directed. |
| 29 | M & L for Forming Contraction (Dummy)joints 65mm deep x 10mm wide,filled with sealing compound, Grade \"B;complete all as specified and directed. |
| 30 | Excavating over areas, n exc 1.5m deep and gettingoutany type ofsoil complete all as specified and as directed. |
| 31 | Removing excavated materials n materials n. exc 50 m and deposited where directed at a level n exc 1.5 m above the starting points in soil complete all as specified and directed. |
| 32 | S& F for Steel rolling shutters Thickness of laths in 1.25 mm, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer;erected in position as indicated,complete but gear operated type with bevel gear box and crank handle complete all as specified and directed. |
| 33 | Supply & fixing \"E\" board605 x 605 x 4 mm thick white prelaminated set & embosed, reinforced, designer ceiling board tiles of approved texture fixed at all height laid on hot dipped galvanised iron imposed grid with 24 mm wide T-section exposed flanges which shall be powder coated, white,.the frame work shall comprises of main runner made from 0.33 mm thick galvanised steel sheet and of size 24 x 32 x 300 mm and spaced at 1200 mm center to center fixed to be structural soffits by approved hangers at 1200 mm rawl center, hangers of GI wire 4 mm dia to be fixed by approved rawl plug, level and fasteners and screws etc., the last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall, flush fitting of 120 mm long cross tee (with double stiching) to be interlocked between main runners at 600 mm center to center, size 1200 x 600 mm modules, cross tee longer than 600 mm to be supported independently on 600 x 600 mm moduler to be formed by fitting 600 mm long cross tee centrally between the 1200 mm cross tee. Tee, perimeter wall angle shall be of 0.45 mm thick GS sheet of size 19 x 19 mm and 300 mm long of white colour all as per manufacturer\"s instructions complete all as directed.Ramco/Charminar/Armstrong) |
| 34 | S&F of pre painted corugated Galvalume roof sheet 0.50mm thick sheeting of colour approved by GE having tensile strength of 550Mpa as in roof covering, wall cladding, doors and similar surfaces fixed withgalvanised 8mm dia \"J\" hook/self tapping screws, all as specified and directed. |
| 35 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding/ vailey gutter towall, fixed with self tapping screws as specified and as directed by Engineer-in-Charge |
| 36 | Dismantling wrought iron or mild steel work of any description not other wise provided complete all as specified and as directed. |
| 37 | S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed. |
| 38 | S&F for wind ties for roof including securingbolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 39 | M&L of two coat of synthetic enamel paint over one coat of red oxideon new steel surfaces of any description over 10cm in width or girthincl preparation of surfaces complete all as specified and directed. |
| 40 | Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed. |
| 41 | Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed. |
| 42 | Excavating in post holes (or similar holes) in hard/dense soil each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed |
| 43 | M & L cement concrete (1:3:6) type C1 (40mm graded stone Agg.) as in embedding of angle iron post all as per specified and directed. |
| 44 | Demolition of Cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for all as specified and directed. |
| 45 | M&L for 150mm bore, PVC (SWR) pipes single socketed in any length with rubber ring joints fixed rain water harvesting of roof covering including PVC clampscomplete all as specified & directed. |
| 46 | S&F galvanised steel wirecloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mmin repairs complete all as directed at site. |
| 47 | S& F for sheet glass 4mm thick, ordinary quality and glazing fixed with aluminium section in squares not exceeding 0.5Sqm in each pane complete all as specified and directed. |
| 48 | M&L for non skid coloured ceramic cut tiles 7-8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but n.exceeding 0.18sqm as in floors set & jointed in neat cement slurry & pointed in white or coloured cement to match the tilesoverincluding screed bed15mm thickin cement mortar (1:4) for laying floor finished completeall as spd and directed. |
| 49 | Taking down chowkats or frames notexceeding 1.5 Sqm(Without taking off shutters from the frame) & removing from site complete all as specified and directed. |
| 50 | Providing and fixing factory made uPVC white colour casement/sliding window/door, made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc.. making arrangement for fixing of hardware, EPDM gasket, 1.2+0.2.mm thick galvanized steel profile to be inserted in required profile, frame will be fixed to the wall with 8mm x100mm long fasteners, all complete and as directed, (Glazing, hardware hinges and fitting, EPDM rubber gasketetc. to be paid separately) Note:-Each member of window to bemeasured separately wrth clear length.Sliding window (two track, 2/4 shutters)C(1) Two track sliding frame (60mm x 62mm) C(2) Sliding window Sash (42 mmx67mm) C(3) Sliding interlock for window (one vertical length in each shutter)(45.5 mmx28mm) C(4) Sliding glazing bead (24.5mmx16mm) C(5) Reinforcement frame (30 mmx 21.5mm) x 2 nos C(6) Reinforcement sash (30 mmx18mm) |
| 51 | Providing and fixing factory made uPVC white color Sliding window Two track made of extruded profiles with wall thickness of 2.3mm (+- 0.2mm). Window profile with hollow section with multi chamber, Frame (60mm x 62mm). sash (42mm x 67mm). Sliding Interlock (One vertical length in each shutters) (45.5mm x 28mm). Glazing bead (24.5mmx 16mm) will he mitered cut and fusion welded at all corners,including drilling of holes for fixing hardware and drainage of water etc.. making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel frame (30mm x 21.5mm), Sash (30mm x 18mm), profile to be inserted in required profile,frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : [Touch Lock of zinc alloyed (white powder coated), steel roller system including 5mm thick glazing with selected quality glass,aluminum track on bottom rail for two track sliding frame, wool pine for Sliding sash and interlock.](Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose)(A) Area not exceeding 2.00 sqm each |
| 52 | Demolition of cement concrete reinforced of any description and in any position not otherwise specifically provided for including cutting of reinforecement to facilitate the demolition and remving the rubbisg off the premises complete all as specified and as directed. |
| 53 | Excavation in trenches not exceeding 1.5m wide and not exceedinf 1.5m in depth; for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth andgetting out in hard/dense complete all as specified and directed. |
| 54 | Returning, filling in of soft/loose soil including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed. |
| 55 | M&L for RCCM-25 (Design mix)(using 20mm graded stone aggregate) as in Walls, retaining walls, basement walls, ballastwalls and the like; any thickness; above top of footings; including attached pilasters and buttressesetc complete all as specified and directed. |
| 56 | Formwork to Formwork to faces of walls,retaining walls, abutments,parapets and staircase railings and similar work including attached pillasters, buttresses,etc.; vertical or to batter complete all as specified and directed. |
| 57 | M&L one coat of synthetic enamel paint on old steel surfaces of any description not otherwise described over 10cm width or girth including preparation of old surfaces complete and all as specified and directed |
| 58 | M&L for preparation of old decorated plastered or unplastered surfaces of walls and applying one coat of cement based paint all complete as specified and as directed. |
| 59 | M&L for preparation of old decorated plastered surfaces of walls and applying one coat of white washing complete all as specified and directed by Engineer-in-Charge. |
| 60 | M&L for preparation of old decorated plastered surfaces of ceilling and applying one coat of white washing on ceilling complete all as specified and directed by Engineer-in-Charge. |
| 61 | M&L for 25 mm thick Plain cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as infloorscement concrete surface rough to receive tiles or other top layerscomplete all as spciified and directed. |
| 62 | M&L for two coat of oil bound distemper white/coloured or tinted on newsurfaces of walls including complete r all as specified and directed by Engineer-in-Charge. |
| 63 | Chipping/removing loose concrete up to reinforcement bars, without damaging the reinforcement, removing all the loose material and to make all the exposedsurface free from dust and all impurities etc. complete allspecified and directed.Note : The work up to three storey building. |
| 64 | Removing corrosion of steel reinforcement by mechanical means like wire brushing, chipping to remove loose rust and then applying rust removal solution by using brush application, leaving the surface for at least 15 to 30 minutes, then removing loose materials by scrubbing or with brush and applying polymer bond to the old concrete surface before applying polymer mortar complete all as specified and directed.Note : The work up to three storey building Make : - SIKA-SIKA Rust off 100 or SIKA S.B.R or latex power.FOSROC - Reebaklens RR or Nitobond AR. |
| 65 | Application of Corrosion Inhibitor Providing & applying One coat of Concrete Penetrating Corrosion Inhibitor (Surface applied) which work on Bipolar Inhibition Mechanism on entire concrete surface to be repaired by using brush or spray at 250 ml per Sq.Mt/Coat or as per manufacture\"s specification and prior to application of frist coat of anti corrosive coating to reinforcement complete all as specified and directed.Note : The work up to three storey building . Make :- SIKA-Feroguard 903FOSROC - Auramix BCI |
| 66 | Providing and applying priming cum bonding coat of polymer of approved make and quality as approved by Engr-in-charge and cement slurry in 1:1 proportionate by weight to concrete area by brush or any other established method etc. complete all as specified and directed. Note : The work up to three storey buildingcomplete. Make:- SIKA- SIKA Latex or SRB FOSROCK - Nitobond EP |
| 67 | Providing Micro Concrete jacketing to walls/columns or beams of thickness upto 50mm using polymer modified cement premixed quartz sand aggregate packed in bags of standard manufacture , for high early strength of 40 N/mm/ sq cm of approved brand.The dry product is to mixed with 12.50% water by weight, along with washed and poured into rigid form work moulds & tamped properly, & cured for 3 days (Payment is to be made by weight premixed of micro concrete product consumed as per site register records. No extra payment shall be made for shuttering or any other material, like scaffoling etc. complete all as specified and directed.Note : The work up to three storey building. Make :- SIKA-SIKA Rep microconcrete-4FOSROC: Rendero CRG |
| 68 | Providing and applyingpolymer modified cement mortor of average thickness 15-20mm using Polymer in one or more layers in proportion 1:5:15 of Polymer Cement Quartz Sand as manufacture\"s specification in speific layers, curing after 72 hours of application with wet gunny bags etc and by finishing the surface with 12 mm thick (1:3) Cement sand plaster complete all as specified and directed. Note : The work up to three storey building.Make:- SIKA- Sika 122 WLFOSROC- Renderoc -S2 |
| 69 | Providing and applying one coat of structural grade epoxy bond coat by brush conforming to ASTM-C-882-87 to the prepared concrete surface to be repaired/strengthened.This is applied prior to the application of polymer repair mortar/epoxy mortar/Microconcrete to have monolithic action between old concretesurface and new concrete surface.Note : The work up to three storey building . Make:- FOSROC- Renderoc -S2 |
| 70 | M&L for glazed ceramic coloured tiles 350x250x7mm/ 450x350x7mm thickon verticalsurfaces such as skirting dados set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including10mm thick rendering in CM (1:4).Complete all as specified & directed. |
| 71 | Providing and applyingpolymer modified cement mortor of average thickness 30-40mm using Polymer intwo layers in proportion 1:5:15 of Polymer Cement Quartz Sand as manufacture\"s specification in speific layers, curing after 72 hours of application with wet gunny bags etc and by finishing the surface with 12 mm thick (1:3) Cement sand plaster. Note : The work up to three storey building . Make:- SIKA- Sika 162 HS FOSROCK- Renderoc HS xtra |
| 72 | M & L for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out inn hard/dense soil complete all as specified and as directed. |
| 73 | M&L Hardcoreofgauge exceeding 63mmofbroken stonesorboulders,deposited,spreadandlevelledin layersnotexceeding 15cmthick,wateredand rammed to a true surface including removal of existing completeall as specified and directed. |
| 74 | M&L 100 mm thick Plain cement concrete1:4:8type D-2(using 40 mm gradedstone aggregate ) as in sub base , fillng and mass concrete or as in receiving tiles/ surface channels and drains etc including demolition complete all as specified and directed. |
| 75 | M&L Chequered cement concrete tiles 20cmx20cmx25mm thick machine pressed set jointed and pointed in neat cement slurry as in floors and cut and polished using grey cement andpigments over screed bed or bedding layer of mortar 15mm thick for laying floor finishes and side opening to be covered in cement mortar (1:4) complete all as specified anddirectedNote : The manufacturer\"s test certificate andindividual test certificate for tilesmust be submitted for approval by the concerned authority prior to installation/fixing. |
| 76 | M & L for pre-cast cement concrete block masonry with solid blocks of cement concrete exc. 10 cm width and setting in cement mortar 1:6 type C-1, 1:3:6 (using 20 mm graded stone aggregate) complete all as specified and directed. |
| 77 | M&L Plain Cement concrete 1:2:4,type B-2, (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete etc complete all as specified and as directed. |
| 78 | S&F Mild Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 gradeSt.-240) complete all as specified and as directed. |
| 79 | S&F Mild Steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted ,bolted or welded attachment.(Fe 410 -W (Gde- E-250) quality -A complete all as specified and as directed. |
| 80 | M&L Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other to be fitted with washers and one hexagonal or square nuts, n exc 5cm long diameter of neck 5 to 10mm complete all as specified and as directed. |
| 81 | M&L for Granite work(of any type) 18 to 20mm thick(table rubbed and polished including round edge) in steps, jambs, pillars, window cills, cooking platforms, wash basin platformand like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 82 | M&L Preparation of newly plastered or un plastered old surfaces of walls, Chajja, balcony, facia etc. by brooming down or steel wire brushing scrapping down, smoke shoots moulds, mass efforescent salt, treating oil and greasy spots etc and applying two coat of cement based paint complete all as specified and directed. |
| 83 | M&L Glazed ceramic coloured tiles 450 x 350 mm x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surface such as dadoincluding 10mm thick 1:3 backingcoat complete all as specified and as directed. |
| 84 | S&F 25mm outer dia of pipes3-layer PP-R (P o l y p r o p y l e n e random copolymer) concealed pipe SDR 7.4 (PN16) UV stabilized andantimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain &brass threaded p o l y p r o p y l e n e random fittingsfixed complete to walls, ceilings or infloors etc. complete all as specified and directed. |
| 85 | S & F in repairs 15mm dia pillar taps fancy type, chromium plated cast copper alloy, with capstain heads screwed down, high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed sanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed. |
| 86 | S&F sinks with drainage board made of stainless steel lmm thick kitchen orlaboratory with plugs, washers and wastes; including bedding in cementmortar to dwarf wall or including fixing cantilever brackets and connectingunion to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 87 | S&F 40mm Waste coupling of PTMT (half or full threaded) of 40mm bore dia of discharge pipe . (Minimum weight 32mm- 45gms/40mm-60 gms) complete all as specified and directed. |
| 88 | M&L 40 mm low density polyethylene (LDPE) pipes of pressure rating 6kgf/sqcm for WHB Including taken down existing one complete all as specified and as directed by Engineer-in-Charge |
| 89 | M&L 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ringjoints laid in trenches or in floors complete all as specified and as directed. |
| 90 | M&L PVC bends 110mm boreincluding taking down existing one complete all as specified and as directed. |
| 91 | M&L PVC (SWR) 110mm junction (single T) equal or unequal provided with access door including taking down existing one complete all as specified and as directed. |
| 92 | M&L RCC 1:2:4, Type B–1 using 20mm graded stone aggregate as in landings, Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like set in cement mortar 1:4 complete all as specified and as directed. |
| 93 | M & Lfor Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed. |
| 94 | M&L 100 mm thick Sand filling under floors or in foundations including watering and consolidationcompleteall as specified and directed. |
| 95 | M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment completeall as specified and directed. |
| 96 | Removal of excavated material to a distance exceeding 1.50 Km andnot exceeding 5.00 Km and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed. |
| 97 | Taking down carefully copper/Alu point wiring (light, fan. socket or power) complete including fixtures and fitings such as switches, ceiling roses, pendents, regulators, sockets , light fitting etc and removing materialsto store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separetely) and making good distrubed surfaces of walls, floors etc. complete all as specified and directed. |
| 98 | M&L for Wiring complete with 1.5 sqmm single core PVC insulated, unsheathed FRLS 1100 volts grade,FRLS cable and incl Stove enemelled steel conduitwith accessories in wall/roof/ceiling/hangar steel frames etc incl Modular terminal boxes fabricated with 1.6mm MS sheet concealed/fixed surface to wallscovered with plastic laminated top cover 2.8mm fixed with cadmium plated iron screws etc and 1.5 sqmm PVC insulated, unsheathed copper conductor multistrandedcable 1100V grade as earth continuity conductor & connecting to common earth dolly all as specified for |
| 99 | One light point/fan/bell point controlled by one switch complete all as specified and directed. |
| 100 | All as per Sl No 98 above but Wiring with 2.5 Sqmm copper multistranded unsheathed cable and 2.5 Sqmm copper cable for earth continuity conductor controlled by one 15A switch socket independently complete all as specified and directed. |
| 101 | S&F Flame proof Weather proof IP 65 rotary switch (Isolator) rating 16 Amps SP with seperate terminal chamber made in die cast alluminiumalloyLM6suitable for Zone 1 & 2, group IIA & IIB ingress protection with all stainless steel hardware and painted with epoxy base powder coated structured paint having temp class T6 certified by CIMFR complete all as specified and directed. |
| 102 | Supply and fix Flame proof - WP switch socket and Plug with rated 16 Amps,Single phase with three pin plug top with seperate terminal chamber made in die cast iron Aluminium alloy LM6 suiteble for Zone 1 & 2, group IIA & IIB ingress protection with all stainless steel hardware and painted with epoxy base powder coated structured paint having temp class T6 certified by CIMFR complete all as specified and directed. |
| 103 | S&F Supply and fixing LED light fitting 2x16 Watt flame proof x 4-feet, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 ingress protection with all stainless steel hardware and painted with epoxy based powder coated structured paint shade 631 of IS:5 having temp class T6 certified by CIMFR + PESO with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed. |
| 104 | S&F Flame proof class 1 zone 1 weather proof wall mounting Exhaust fan 15\" (380mm) sweep 1440 RPM single phase suitable rated 240 volts 50 cycle with CMR/CPRI hazardous area gas group IIA/Iib with fabricated construction casing suitable propeller wheel with dynamically balanced blades to avoid frictional spark hazardous front and rear wire guards 01 No, M-20 cable entry etc suitable for wall/bracket mounting arrangement etc duly dark grey epoxy powder coated as per shade 632 of IS-5 complete in all respect including wiring MES No 2 CM height with synthetic enamelled black paint all as directed.Note:- Civil work is included in quoted rate. |
| 105 | S&F Flame Proof class 1 Zone 1 Weather proof wall mountingFan 18\" (457 mm) sweep, 1440 RPM single phase, suitable rated 240 Volts, 50 Cycles with CMR / CPRI hazardous area gas groups IIA/IIB with fabricated construction casing suitable propeller wheel with dynamically balanced blades to avoid frictional spark hazardous front and rear wire guards - 01No, M-20 cable entry etc suitable for wall / bracket mounting arrangement etc, including writing MES NO. 2 CM height with synthetic enamelled black paintcomplete all as directed. |
| 106 | S&F ceiling rose, surface type Bakelite 65x55mm3 terminal complete all as specified and directed. |
| 107 | Supply and fixing replacementfactory madepowder coated distribution board TPN 4 way, double doorincludingbus bar, Neutral bar, standard DIN rail, earth bar acomplete all as specified and directed. |
| 108 | S&F Triple pole Nuetral MCB 63 Amp , 415 v, 50 Hz ACsuitable for ‘C’ curve, 10 KA breaking capacitycomplete conforming to IS 8828 of 1996 all as specified. |
| 109 | Supply and fixing singlepole MCB 6 to 32 Amps, 240 v, 50 Hz ACsuitable for ‘C’ curve, 10 KA breaking capacity conforming to IS 8828 of 1996all as specified. |
| 110 | M&L earthing complete with GI earth plate electrode 600mmx600mmx6mm thick buried in ground vertically to a depth not less than 2.25 mtrs below ground level with top edge of earth plate not less than 1.5 mtrs below ground level connected with GI wire 4mm dia and GIbolts, nuts, etc and protected by GI pipe light grade 40mm bore and 20 mm dia GI tubing light grade with funnelfor watering, connecting to test point, all as shown in electrical plate No.3 of SSR Part I incl necessary earth work and excavation in any type of soil, PCC earth chamber withRCC cover slab, salt, charcoal and MS hook, ane provn of test point complete all as specified and directed.NOTE : GI wire upto 7.5 Mtrs shall be included in quoted rates and beyond 7.5 mtrs shall be measured and paid separately. |
AI Tender Summary
Tender Timeline
Jul 12, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedJul 31, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 02, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender