Tender For Spl Repairs To Bldg No Np-02 At Mes Complex At Naa Under Ge (N) Tezpur.; 1 Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed 2 Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 sqm each complete all as specified and as directed 3 Taking down cement plaster on stone/brick/concrete surfaces including racking out joint, hacking for key, scrubbing down with water etc, complete all as specified and as directed. 4 Material and labour for brick work with sub-class B old size bricks of class designation 75, straight or curved on plan exceeding 6m mean radiusbuilt in cement mortar (1:6) including dismantling of existing brick work built in cement mortar complete in all respect as specified and directed. 5 M&L for half brick work with subclass ‘B’ old size bricks of class designation 75, straight or curved on plan exc. 6m mean radius built in CM (1:4) including dismantalling of brick work built in cement mortar in any position, complete in all respect as specified and directed. 6 S&F in repairs second class hardwood plain,solid ,straight,chowkats and frames,wrought, framed rebated on the solid ,rounded or chamfered,put together with glue pinned at joints, complete in all respect as specified and directed. 7 M&L for cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs, slab staging for water tanks, filling of pressed steel door frame, fixing of hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formworks including dismantling of existing surface complete all as specified and directed. 8 S&F in repairs framed work such as grills, gratings,etc with ends of bars shouldered and /or riveted, or forged into spikes framed guard bars barred iron doors , laddersand similar work conforming to Fe 410-0 or FE310-0 complete all as specified and directed. 9 S&F in repairs mortice lock, vertical type, mild steel, 2 levers, vertical type, 100 mm size including protective coating of painting fixed in position complete all as specified and directed. 10 S&F in repairs Rooftrusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular/hollow section, channel or flat sections) including distance pieces, cleats etc. using Fe-410W (Grade E-250 quality A) including necessary welding complete complete allas specified and directed. 11 M&L for 20-25 mm thick machine cut kota stone slab flooring of size not less than 500 x 500 mm over 15 mm thick cement mortar (CM) 1:6 screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, including dismantling of existing surface complete all as specified and directed. 12 M&L for 20-25 mm thick machine cut kota stone slab of size not less than 500 x 500 mm in riser of steps, skirting, dado and pillar over 15 mm thick rendering in cement mortar (CM) 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, including dismantling of existing surface complete all as specified and directed. 13 S&F coloured 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based trapezoid profile steel sheet having tensile strenght of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws with bitumen washer to truss members of any material, including taking down existing sheet complete all as specified and directed. 14 S&F coloured 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based trapezoid profile steel sheet having tensile strenght of 550 Mpa as in ridge, valley gutter or of similar type, fixed with self tapping screws with bitumen washer to truss members of any material, including taking down existing sheet complete all as specified and directed. (The measurement shall be carried out as in a plain sheet). 15 S&F coloured 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based plain steel sheet having tensile strenght of 550 Mpa as in eves covering or of similar type, fixed with self tapping screws with bitumen washer over mild steel flats, angles etc. and screws for fixing with framed structure including taking down existing sheet complete all as specified and directed. (Note:- MS work shall be measured and paid separately). 16 S&F exposed GI powder coated snap grid frame work for false ceiling in flat or in sloping, of grid size 600 x 600 mm comprising of wall/ cleat angle of size 25x25x0.35 mm and corss tee of size 24x38x0.70 mm with 4 mm dia GI wire as suspender and including 4 mm thick decorative pre-painted non asbestos board (E-Board) in false ceiling including fixing arrangement from steel/ wooden truss of any type including dismantling of existing false ceiling boards, complete in all respect as specified and directed. (Make:- Eternit, Everest or equivalent) 17 Providing and fixing false ceiling at all height including fixing of frame work made of special section power press from m.s Sheets and galvanized with zing coating of 120 gram g.m.s /sqm includind fixing Perimeter channels 0.5 mm thick 27mm height Heading flages of 20 mm and 30mm long, the Perimeter of ceiling fix to wall with the Help of rawl plugs including fixing of 12mm Gypsum board including jointing and Finishing to a flush finish. With putty , Primer and double coat ceiling paint finish including dismantling of existing surface complete all as specified and directed 18 Providing and laying skid/non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floor etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick screed bed in cement mortar (CM) 1:6,including dismantling of existing surface complete all as specified and directed 19 M&L for screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and as directed. 20 Providing and laying coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.08 sqm but not exceeding 0.15 sqm, in skrting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick rendering in cement mortar (CM) 1:4, including dismantling of existing surface complete all as specified and directed 21 M&L for any colour of granite stone without white spots Granite stone slab 17 to 19 mm thick, as in floor, dado, steps, laid over and including screed bed 15 mm thick in cement mortar (CM) 1:6, jointed and pointed with white cement mixed with pigment to match the shade of stone including cuttingl rubbing and polishing surface, including cutting for wash hand basin, sink, gas pipe hole etc., to the entire satisfaction of the Engineer-in-Charge, complete in all respect as specified and directed. 22 M&L for Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, infloors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles including dismantling of existing surface complete all as specified and directed 23 Material and labour for Cleaning and preparation of roof/wall (RCC/BRICK/tiles/Cement cuncrete) surface and made free of dirt, foreign particles, laitance followed by grinding all protrusions to make surface modulated. Thereafter, inspection for cracks on the surface ceused by thermal expansion/ contraction and repairing the cracks on the surface caused by thermal machine, filled with Repair Mortar/General purpose Grout in the proportions as recommended by manufacturer, supplying and applying High performance Hybrid Polyurea waterproofing coating spray/hand applied liquid membrane including taking of existing roof treatment and apply with following specifications: (a) Elongation of range 400% 600% (b) Tensile strength of 8-12 N/mm2. (c) Crack bridging ability of 3.00-4.00mm (d) Hardness (Shore A ASTM D2240) of range 50-70 The application shall include final base preparation, epoxy primer application in rato 1.1 (resin: hardner) with 100% water dilution and application of Hybrid polyurea in two coats in 6 hrs interval to achieve total min thickness 1 to 1.50mm. The application/ treatment shall be carried out by authorized rep of approved specialist firm/manufacturer Make- SIKA/FOSROC/Asian Paints/Berger. Note: The defect liability period of water proofing treatment shall be 10 years and the contractor shall beespor building(s) free From leakage/seepage for a period of completion. The contractor may obtain a similar guarantee by him for the purpose. 10 years after certified date of completion. the contractor may obtain a similar guarantee from the specialist firm engaged by him for purpose. 24 M&L 15 mm thick plastering on brick/ stone/ concrete surfaces of wall in cement mortar (1:4), finished even & smooth without using extra cement, including taking down existing surface complete all as specified and directed. 25 M&L 15 mm thick plastering on brick/ stone/ concrete surfaces of of wall in cement mortar (1:6), finished even and smooth without using extra cement, including taking down existing surface complete all as specified and directed. 26 M&L 10 mm thick plastering on brick/ stone/ concrete surfaces of ceiling in cement mortar (1:3) finished even and smooth without using extra cement, including taking down existing surface complete all as specified and directed. 27 Supply only integral water proofing compound complete all as specified and as directed. 28 Supplying and laying in repairs CPVC pipes for potable hot and cold water distribution, nominal size 16 mm, pressure class 1, SDR 11 including plain CPVC fittings of pressure class 1, SDR 11 in trenches complete all as specified and as directed. 29 Supplying and laying in repairs CPVC pipes for potable hot and cold water distribution, nominal size 20 mm, pressure class 1, SDR 11 including plain CPVC fittings of pressure class 1, SDR 11 in trenches complete all as specified and as directed. 30 S&F in repairs 20 mm gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed to pipe complete all as specified and directed. 31 S&F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. or for window grill of appd size and shapeincluding fixing with aluminium U shape section for fixing etc. complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note:all external members to be joined at 45 degree angle at corner) complete all as specified and directed. 32 S&F powder coated aluminium three tier window frame including necessary joining cleats, of Jindal section No 20832 or equivalent section of appd make of 1.5mm thick complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note:all external members to be joined at 45 degree angle at corner) 33 S&F of powder coated aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in ewach door, hinges, anodised aluminium snap beading screws etc. complete all as specified and directed. 34 S&F in repairs Factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/ Chowkhat of size 65 X 100mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk / wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face)& 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite / borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/ss dash fasteners of required dia and length complete as per direction of enineer-in-Charge (M.S. hold fast/lugs or SS dash fastener shall be paid for seperately)Note: For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 35 S&F in repair Single unit (single piece) wash down water closet panwhite including plastic water closet seat cover white, Single unit with flat bottom, new CI/UPVC P or S type trap and mild steel chromium plated hinging devicecomplete in all respect as specified and directed Make:- Hindware, Jaquar, Marc, Prayag. 36 M&L in repairs for solid PVC wall lining consisting of 5 mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and as directed. 37 S&F powder coated aluminium sliding window with/without sash bars, aluminium sections of thickness 2mmincluding necessary joining cleats, glazing clips, EPDM rubber packing (of 50 No grade), powder coated aluminium snap beading, screws, center grooved stainless steel ball-bearing double roller2 position height adjustment, sound/dust brush, recessed handle with locking arrangement complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note:all external members to be joined at 45 degree angle at corner) complete in all respect as specified and directed. 38 S&F 75 mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and as directed. 39 S&F 100 mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and as directed. 40 Supply and fix solid PVC door frames of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube all as per specification & drawing complete all as specified and directed by Engineer in charge. 41 S&F factory made solid PVC moulded door shutter, 28 to 30 mm thick (stiles) with particle board core, with 2, 4, or 6 raised panel design with 2 mm thick Moulded PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing. 42 S&F 35mm thick second class HW glazed and skeleton shutters, open rebated and prepared to receive glass gauge etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass etc.; sizes of members of shuttrs as specified in SSR Part-I, section 8, clause 8.24 (a), complete in all respect as specified and directed. 43 S&F in repairs 4 mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in square not exceeding 0.5 sqm in each pane complete all as specified and as directed. 44 Supply & fix in repairs sheet glass, ordinary quality, 4 mm thick and glazed with oil putty or fixed with beads in square not exceeding 0.5 Sqm in each pane complete all as specified and directed. 45 S&F in repairs stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed. 46 S&F flush door shutters, 30 mm thick, solid core of block boards construction, MR grade, commercial type with stiles, rails and lipping of timber as given in Group 2A and Group 2B of Annex B of IS 2202 (Part 1): 1999, both sides face panels of plywood as per IS 710: 2010, internally lipped complete all as specified and as directed. 47 S&F in repairs BRASK Brass Tower Bolt Xylo Heavyand rolled or cast bolts 300 mm long, complete in all respect as specified and directed. 48 S&F cast brass handle, cast type, 150 mm size, nickel chromium plated finish as per service grade number 4 of IS 1068: 1993 complete all as specified and as directed. 49 S&F aluminium anodised sliding door bolts with hasp and staple (boilt type) 16 mm dia bolt, 250 mm long, with and including a minium of 6 bolts and nuts four on bolt plate and two on staple plate, complete in all respect as specified and directed 50 S&F brass sliding door bolts with sand-cast brass hasp, staple and fixing bolts or clips and rolled or drawn brass bolts (type-1) or Brass sliding door bits with diecast brass hasp, staple and fixing bolts or clips and rolled or drawn brass bolts (type -2), satin finish or polished, 250 mm long complete all as specified and as directed. 51 S&F mild steel door spring of rat tail type of size 300 mm, bright finish including roller and roller plate complete all as specified and as directed. 52 S&F PVC coloured insulated over MS pipe 20 mm dia curtain rod with fixing bracket, stops, rollers etc. complete all as specified and directed. 53 S&F in repairs 4 mm thick of size 600 mm x 450 mm bevelled edge mirror of selected quality decorative type mounted on 6 mm commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete in all respect as specified and directed. 54 S&F in repairs 5.50 mm thick of 2.0 m x 1.00 m size bevelled edge mirror of selected quality decorative type designer mirror with chromium plated brass screws and cup washerscomplete all as specified and directed. 55 S&F three layered white in colour rotational moulded made out from LLDPE material water storage tanks of capacity 1000 ltr (cylindrical vertical with closed top) including three tank nipples of 20 mm nominal bore dia hoisted and fixed in position including dismantling/ taking down all as specified in SSR part I, complete in all respect as specified and directed. Make:- Sheetal (Virat), Sintex, Oriplast, Supreme 56 S&F in repairs ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of 20 mm size, minimum weight 210 grams complete all as specified and as directed by the Engineer-in-Charge. (MAKE : PRAYAG, Cat No: 152 or equivalent model in JEXON / POLYTUF / SHAKTI) 57 S&F in repairs 15 mm nominal size, nonrising spindle type fancy concealed stop valves as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed 58 M&L for cement concrete M15 (Nominal Mix) using 12.5 mm nominal size graded crushed stone aggregate as in floor 25 mm thick finished even and fair including dismantling of existing surface complete all as specified and directed. 59 S&F in repairs Vitreous China urinals, full stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern complete all as specified and directed. 60 S&F for coloured rubber moulded, glazed pre coated chequered cement concrete tiles of any shape and size 20-25mm thick with grey cement with pigment,; set jointed and pointed in neat cement slurry with pigment in floors including over 15mm thick screed bed in CM 1:4 including dismantling of existing surface complete all as specified and directed. 61 Providing & laying heavy duty non skid coloured digital printed floor tiles of size 300mmX300mm ,8 to 10mm thick set and jointed in neat cement slurry and pointed with white cement with pigment to match the tiles colour over and including 15mm thick screed bedding in cm 1:6 and dismentling of existing tiles/blocks of any discription complete in all respect as specified and directed. make-somany(heavy duty),johnson (Endura), Orient Bell(Pavers) 62 M&L for cement concrete in foundation, filling and mass concrete in M7.5(Nominal Mix) using 40 mm nominal size graded crushed stone aggregate including dismantling of existing surface complete all as specified and directed. 63 M&L for hardcore (broken stone or boulders) of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed. 64 S&F in repair EWC vitrous china colour/white , P or S trap,incliding connection to drain or out going pipe and to flushing pipe with plastic water closetseat white pattern , flat bottom and coverincluding MS CP hinges complete all as specified and directed. 65 S&F in repairs 15mm size PVC connection pipe with PTMT nut of length 450mm complete all as specified and directed. 66 S&F in repair vitreous chinaware sqatting pan of size 580 x 440 mm, ORISSA PATTERN with new PVC P or S trap bedded in cement concrete (excluding flushing cistern and flush pipe) with integral foot rests, complete in all respect as specified and directed. 67 S&F in repairs 15 mm bore fancy type CP finished angle valves, cast copper alloy, screwed down, high pre-ssure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete in all respect as specified and directed. 68 S&F in repairs CP finish cast copper alloy, two way bib cock complete in all respect as specified and directed.. Make:- Make:- Jaquar cat part No ALI-CHR-85041 69 S&F in repairs long body Bib taps of 15 mm bore, fancy type CP finish cast copper alloy with crutch handle, screwed down, screwed for iron pipes, complete in all respect as specified and directed. 70 S&F in repairs short body Bib taps of 15 mm bore, fancy type CP finish cast copper alloy with crutch handle, screwed down, screwed for iron pipes, complete in all respect as specified and directed. 71 S&F in repair Health faucet cast coper alloy CP finish 15 mm dia fancy type with brass plated flexible hose and wall hook, 1.00 mtr complete, in all respect as specified and directed. Make:- Jaquar, Hindware Cat part No F-160002 72 Supply and fixed in repair 15mm bore, cast ABS body, CP finish, shower rose of size 125 mm dia and shower arm of cast copper alloy CP finished, fixed to iron pipe/fiitingscomplete in all respect as specified and directed. 73 S&F towel rack 600mm long of cast copper alloy, chromium plated with end brackets complete in all respect as specified and directed.(cat part no-AHS-CHR-1581H) 74 S&F 15 mm rubber tiles for gym of any colour, complete all as specified and directed. 75 S&F in repairs corner Sheet glass shelf assembly consisting of 5.5mm thick corner sheet glass shelf with chromium plated brass brackets complete all as specified and directed.make-jaquar(cat part no-ACN-CHR-1173) 76 S&F in repair wash hand basins (WHB), vitreous china of size 550x400 mm (flat back or angle back type), including cutting for and pinning in ends of brackets over new angle iron erecting stand embedded in PCC (1:2:4) block including 32 mm dia bore waste fittings cast copper alloy chromium plated with long screwed shanks and flynuts flange and beded in redlead cement, PVC waste pipe including 15 mm bore dia fancy type CP finish Pillar tap, cast copper alloy with capstand heads, screw down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screw for iron pipes complete in all respect as specified and directed. 77 M&L for coloured ceramic tiles 8 to 10 mm thick (square/ rectangular) area of eachtile exceeding 0.18 Sqm but not exceeding 0.72 Sqm, in dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile colour including dismantling of existing surface complete all as specified and directed. 78 Supply and fix in repairs PVC SWR Nahani/ Floor trap plain with grating including jointing with solvent cement, dia of outlet 75 mm, water seal minimum 50 mm, complete all as specified and directed by Engineer in charge. 79 S&F in repairs PVC (SWR), type A as per IS 13592: 2013 single socketed rain water pipes in any length with rubber ring joints, 110 mm dia, fixed to walls complete all as specified and as directed. 80 S&F in repairs towel ring of copper alloy CP finished complete in all respect as specified and directed. 81 S&F in repairs PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 75mm bore including necessary MS pipe clamp, complete in all respect as specified and directed. 82 S&F in repairs PVC (SWR) pipes single sockedted in any length with rubber ring joints laying in trenches 110 mm bore, complete in all respect as specified and directed. 83 S&F in repairs PVC (SWR) pipes single sockedted in any length with rubber ring joints laying in trenches 75 mm bore, complete in all respect as specified and directed. 84 S&F in repairs PVC (SWR) Tee(87.5⁰) single, 110 mm dia with inspection door conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge. 85 S&Fin repairs PVC (SWR) Tee(87.5⁰) single, 75 mm dia with inspection door conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge. 86 S&F3mm thick aluminium composite exterior grade plane panel sheet of approved colour size, shape, description for base of sign board including necessary stainless steel nut bolts fixed on stainless steel section complete all as specified and directed. Make 3M or equivalent. 87 S&F in repairs PVC (SWR) bends without inspection door (any angle), 110 mm dia conforming to IS 14735: 1999 complete all as specified and directed. 88 S&F in repairs PVC (SWR) bends without inspection door (any angle), 75 mm dia conforming to IS 14735: 1999 complete all as specified and directed. 89 S&F in repairs PVC (SWR) vent cowl, 110 mm dia conforming to IS 14735: 1999 complete all as specified and as directed. 90 S&F in repairs PVC (SWR) vent cowl, 75 mm dia conforming to IS 14735: 1999 complete all as specified and directed. 91 S&F in repairs Itched toughened frosted glass 12mm thick for partition and door fixed with stainless steel hinges ,handle and stainless steel fixing cleat complete in all respect as specified and directed. 92 Supply and fixed in repairs unplasticised PVC (SWR) Gully trap125/110 mm, setting and jointing with solvent cement complete in all respect as specified and directed. Make: Supreme, Prince, Oriplast. 93 M&L for precast RCC, type B-1, 1:2:4 (using 20 mm crushed and graded stone aggregate) as in manhole covers/ cover slabs or of similar type slab works, etc. incl necessary formwork and loading/ unloading of the same and fixed in position, including dismantling of existing surface complete all as specified and directed. 94 M&L for RCC M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate as in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses including dismantling of existing surface complete all as specified and directed. 95 S&F in repair Exposed Part Kit of Single Lever Hi Flow In-wall Diverter (Compatible In-wall part ALD-079N is sold separately) complete in all respect as specified and directed. Make:- Jaquar (cat part : (ALI-CHR-85079NK ). 96 S&F in repair Alive Maze Hand Shower 68x100mm Round Edge & Rectangular Head Single Flow(Face Plate Stainless Steel & ABS Body in Chrome finish) with Rubit Cleaning System complete in all respect as specified and directed. Make:- Jaquar (cat part : (HSH-CHR-85537 ). 97 S&F in repair Premium Wall Bracket For Hand Shower, ø35mm & 100mm Long Round Shape complete in all respect as specified and directed. Make:- Jaquar (cat part : SHA-CHR-555 ). 98 M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 10 cm but not exceeding 20 cm wide for rough finished surfaces of concrete complete all as specified and as directed. 99 M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and as directed. 100 S&F in repairs 8 mm thick curved shaped urinal partition with frosted glass size 900 x 450 mm including stainless steel fixing brackets complete in all respect as specified and directed. 101 M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height. Complete all as specified and as directed. 102 M&L 75 mm thick PCC (1:3:6) type C-2 using 40 mm nominal size crushed and graded stone aggregate laid in floor, path etc. or of similar type finished the surface even and fair without using extra cement including dismantling of existing surface complete all as specified and directed. 103 M&L for preparation of old decorated plastered surface of wall after complete removal of existing treatment and applying two coats of weather coat over 2 mm thick wall care putty (in two layers) over a coat of primer including preparation of surface, complete in all respect as specified and directed. 104 M&L for complete removal of existing treatment on wall and applying two coats of oil bound distemper (OBD) and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2 mm thick (in two layers) wall care putty, complete in all respect as specified and directed. 105 M&L for preparation of old decorated plastered surface of ceiling and applying two coats of oil bound distemper including filling of voids with wall care putty on plastered surface including complete removal of existig treatment, complete in all respect as specified and directed. 106 M&L for preparation of newly plastered surface of wall and applying two coats of weather coat over 2 mm thick wall care putty over a coat of primer including necessary preparation of surface, complete in all respect as specified and directed. 107 M&L for preparation of newly undecorated plastered surface of wall and applying two coats of oil bound distemper (OBD) and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2 mm thick (in two layers), wall care putty, complete in all respect as specified and directed. 108 S&F in repair Counter Top Basin, Size: 600x400x185 mm including Waste coupling 32 mm SS and Bottle Trap 32mm Size with 300mm & 190mm Long Wall Connection Pipes & Wall Flange ,complete in all respect as specified and directed. Make:- Jaquar, Cat Part No. SLS-WHT-6601, 109 S&F in Exposed Part Kit of Single Lever Basin Mixer Wall Mounted Consisting of Operating Lever, Cartridge Sleeve, Wall Flange, Nipple & Spout (Compatible with ALD-233N & ALD-235N) complete in all respect as specified and directed. Make:- Jaquar (cat part : (ALI-CHR-85233NK ). 110 S&F in Concealed Body for Single Lever Basin Mixer Wall Mounted, But without Exposed Parts complete in all respect as specified and directed. Make:- Jaquar (cat part : (ALD-CHR-233N ). 111 S&F in repair Bathtub Spout with Button Attachment For Hand Shower With Wall Flange complete in all respect as specified and directed. Make:- Jaquar (cat part : (SPJ-CHR-85463 ). 112 S&F in repair Flexible Tube 8mm dia & 1.5M Long with Nuts complete in all respect as specified and directed. Make:- Jaquar (cat part : (SHA-CHR-549D8 ). 113 S&F powder coated aluminium ventilator with half portion louvered (adjustable)with 4mm thick glass in louver and balanced portion fixed 4mm thick frosted glass glazing including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings complete in all respect as specified and directed. 114 Preparation of newly or previously untreated steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge 115 M&L for preparing of old decorated wooden surface, of any description, not otherwise described, over 10 cm width or girth, and applying two coats of synthetic enamel paint, complete in all respect as specified and directed. 116 M&L for anodised aluminium frame poder coating ( Minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed. 117 M&L in replacement of point wiring with 1.5 sqmmFRLSH, PVC insulated stranded copper conductor single core including non metalic PVC conduit medium grade (MMS ISI) of size not less than 20 mm dia(or as site requirement) concealed in wall/over ceiling,modular metal flush boxes of required size and with modular plates incl of all accessories and all as specified including 1.5 sqmm FRLSH PVC insulated sheathed multistranded copper earth conductor to common earth and connected to earth dollyfor light / fan/ bell point controlled by one switch.Note:- (i) Cost of PVC conduit, modular plates,frames, cover plates etc; are deemed to be included in the quoted rate.(ii) M&L for cutting chases on walls / ceilingand making good disturbed surfaces including finishing with cement mortar (1:3) etc; are deemed to be included in the quoted rate. 118 All as per item 117 above but for 3 pin 5 Amps switch socket on independent board with 1.5 sq mm copper cable complete all as specified and directed. 119 All as per item 117 above but for 3 pin 16 Amps switch socket combination on independent board with 2.5 sq mm copper cable complete all as specified and directed. 120 All as per item 117 above but for 5 Amps socket point on the same board controlled by one switch complete all as specified and directed. 121 S&F in replacement of modular switch10A,1 module single pole, one waycomplete all as specified and directed. 122 S&F in replacement of modular socket outlet 5 pin ,10 Amps,2 module, 240 Volts complete all as specified and directed. 123 S&F in replacement of modular switch16A, 1 module single pole, one waycomplete all as specified and directed. 124 S&F in replacement of modular socket outlet 5 pin ,16 Amps,2 module, 240 Volts complete all as specified and directed. 125 S&F in replacement of modular bell push switch 5 Amps complete all as specified and directed. 126 S&F in repairs call bell, multi music type suitable for single phase, AC, 240 volts complete all as specified and as directed. 127 S&F in replacement ofceiling rose polycarbonate typethree terminals complete all as specified and directed. 128 S&F in replacement of modular step type electronic fan regulator ,two module 120 watt single pole 240 Volts complete all as specified 129 S&F in replacement LED Tube light luminaires, 20-22 watts, lumen output not lessthan 2000 (4 feet), made of anodised extruded aluminium housng, with high transmissivity diffuser, high lumen output, with suitable integrated electronic driver, and operated in single phase, 230 volts, 50HZ, all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable offrom connector and ceiling rose, complete all as specified and directed. Make :- Philips model SmartBright or equivalent in Wipro / Crompton 130 M&L in replacement of for 12W LED mirror light fitting warmfancy type of make Philips model No 31402 Bronze finish or of equivalent make as complete all as specified and directed. 131 M&L in replacement of for LED wall Decorative light fitting of make Philips GraceIp44 Led Wall Light suitable for 20W LED lamp or of equivalent makecomplete in all respect as specified and directed. 132 S&F in replacement of round shape 12/15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete in all respect as specified and directed. 133 Supply and draw in replacement of submain wiring with two single core 6 sq mm FRLSH PVC insulated copper cable 1100 volts grade multi stranded, sheathed conductor in concealed PVC conduitincluding 6 sq mm multi-strand FRLSHPVC insulated copper wire for earth continuity conductor connected to common earth dolly complete and making good disturbed surface complete.Note:- Cost of PVC conduit, cutting chases on walls and making good disturbed wall surfaces including finishing with cement mortar (1:4) matching with the existing shade / tint are deemed to be included in the rates quoted. 134 Supply and draw in replacement of submain wiring with two single core 4 sq mm FRLSH PVC insulated copper cable 1100 volts grade multi stranded, sheathed conductor in PVC casing cappingincluding 4 sq mm multi-strand FRLSHPVC insulated copper wire for earth continuity conductor connected to common earth dolly including necessary fittingS&Fixtures and including PVC terminal box and PVC board making good disturbed surface with CM (1:4) to match with the existing surfacecomplete and making good disturbed surface complete.Note:- Cost of PVC conduit and making good disturbed wall surfaces including finishingwith cement mortar (1:4) matching with the existing shade / tint are deemed to be included in the rates quoted. 135 S&F in replacement new generation energy saving and environmental friendly long life 35/40W LED wall street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having top Opening seperate driver compartment with IP66 protection and impact resistance of IK07including necessary brackets (made out of suitable bore GI pipe light grade appx 0.6 meter long bend to shape) nuts, bolts, etc fixed on walls with MS clamp complete all as specified and directed. Make:- Philips of Model -SmartBright Street or equivalent in Wipro / Crompton. 136 S&F in replacement LED recess mounted (2x2 size flat panel) luminaire which provide soft light and glare free symmertical illumination suitable for armstrong/grid ceiling of 36Watt,(Lumen output not lessthan 3600) complete all as specified and directed.Make Philips Smart Glow(Cat No:- RC383B LED 36S-6500 PSU OD WH PIR). 137 Supply and fixing in replacement of single pole and neutral enclouser with atwo pin and earth plug and socket complete with one pole MCB 20 Amps complete all as spd and directed. 138 M&L in replacement ofsheet metal enclosure for Ekinox TPN DB-VTPN 4 way 415 V, double door , 250 A copper bus bar , IP 43 , including 100 Amp MCCB as incomer as flush mounted complete all as specified and as directed.(Make -Legrand(Series 5077 45 to 48) 139 Supply & Lay in replacement of trenches fixed on wall (or) passing through pipes/in floors connecting up testing and commissioning of XLPE insulated armoured LT UG electric cable with aluminium conductor 1100V grade of size 50sqmm 3.5 core complete all as specified and directed by Engr-in Charge. 140 Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or water supply pipes lines etc or not exceeding 10 sqm on plan and getting out in soft/ loose soil complete all as specified and as directed. 141 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose/ hard/ dense soil complete all as specified and as directed. 142 Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed. 143 Supply & spreading in trenches sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly. 144 M&L laying well burnt old size bricks, sub calss B bricks, straight or curved on plan, laid flat with width equal to length of brick, laid dry over electric cablefor protection all complete all as specified and directed. 145 S&F in replacement of sheet metal enclosure double doorfor MCB DBs SPN 12 way 240 V, complete flush mounted all as specified and as directed. 146 S&Fin replacement of MCB single pole (SP) 5 to 40 Amps,240 volts , C curve , AC , 50 Hz ,10 kA complete all as specified and directed. 147 S&F in replacement of MCB Single pole & neutral (SPN)32 Amps, 240 volts , C Curve, AC , 10 kA complete all as specified and directed. 148 M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Metre below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 15 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as shown on electrical plate No. 3 of SSR part - I , including taking out old U/s complete alll as specified and directed .
