Tender For Routine Repair And Maintenance Of Civil Works At Nsc Jayant For Period Of 02 Years -- 1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil. 2 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size). 4 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size). 5 Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but, excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size). 6 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) 7 Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge.With cement mortar 1:4 (1cement: 4 coarse sand) 8 12 mm cement plaster finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand) 9 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick 10 Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 800x800 mm 11 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 12 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar 13 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 14 Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :Of area 3 sq. metres and below 15 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 16 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 17 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Cold twisted bars 18 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 19 Finishing walls with Acrylic Smooth exterior paint of required shade:Old work (One or more coat applied @ 0.90 ltr/10 sqm). 20 Applying priming coat:With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) 21 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 22 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two or more coats on new work 23 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work 24 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work 25 French spirit polishing :One or more coats on old work 26 Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 27 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade One or more coats on old work 28 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing,paneling and dash fasteners to be paid for separately) :For fixed portion,Powder coated aluminium (minimum thickness of powder coating 50 micron) 29 For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately),Powder coated aluminium (minimum thickness of powder coating 50 micron) 30 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) 31 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge.Pre-laminated particle board with decorative lamination on both sides,80 mm thick C.C. paver block of M-30 grade with approved color design andpattern. 32 Welding by gas or electric plant including transportation of plant at site etc. complete. 33 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge,80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. 34 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil 35 Carriage of material by Mechanical Transport including loading, unloading and stackingLime, moorum, building rubbish Lead - 2 Km 36 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 37 Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With stainless steel cover plate minimum 1.25 mm thickness 38 Grading roof for water proofing treatment withCement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 39 35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturers specification and direction of Engineer- in-charge.Non decorative finish (matt finish) 40 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade.Area of slab upto 0.50 sqm 41 Providing and fixing 16 mm M.S. Fan clamps of standard shape and size in existing R.C.C. slab, including cutting chase, anchoring clamp to reinforcement bar, including cleaning, refilling, making good the chase with matching concrete, plastering and painting the exposed portion of the clamps complete. 42 Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Old work (one or more coats) 43 Lettering with black Japan paint of approved brand and manufacture 44 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 45 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :250 mm dia. R.C.C. pipe 46 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :100 mm diameter 47 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :150 mm diameter 48 Providing and fixing soil, waste and vent pipes :100 mm dia,Sand cast iron S&S pipe as per IS: 1729 49 Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :100 mm dia pipe 50 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter 51 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :For 100 mm dia pipe 52 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110 mm 53 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Bend 87.5°,110 mm bend 54 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.110 mm Shoe 55 Providing and fixing 100 mm sand cast Iron grating for gully trap. 56 Providing and fixing PTMT grating of approved quality and colour.Circular type,100 mm nominal dia 57 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :30 mm thick shutters,With ISI marked stainless steel butt hinges of required size,Kiln seasoned and chemically treated hollock wood 58 Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.Kiln seasoned and chemically treated hollock wood,30 mm thick shutters 59 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Kiln seasoned and chemically treated hollock wood 60 Providing and fixing aluminum U beading of required size to Pre-laminated/ flush door shutter, including fixing etc. complete as per direction of Engineer-in-charge. 61 Cutting holes up to 30x30 cm in walls including making good the same:With common burnt clay F.P.S. (non modular) bricks 62 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. 63 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 64 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm 65 Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge. 66 Providing and fixing white vitreous china water closet squatting pan (Indian type) :Orissa pattern W.C. pan of size 580x440 mm 67 Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan. 68 Brick work with FALG bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) 69 Brick work with FALG bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) 70 Half brick masonry with FALG bricks of class designation 7.5 in foundations and plinth in :cement mortar 1:4 (1 cement : 4 coarse sand) 71 Providing following items at the site.Nickel plated M.S. pipe 20 mm dia 72 Providing following items at the site.Nickel plated M.S. pipe 25 mm dia 73 M.S. Nickel plated BracketNickel plated M.S - Brackets for curtain rod 20 mm 74 M.S. Nickel plated Bracket.Nickel plated M.S - Brackets for curtain rod 25 mm 75 Providing/ Supplying of Flush door Shutters.18 mm thickBlock board with commercial Ply 76 Providing/ Supplying of Flush door Shutters.Block board construction flush door with commercial ply on both faces 25 mm thick 77 Providing/ Supplying of Flush door Shutters.Block board construction flush door with commercial ply on both faces 30 mm thick 78 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Hydraulic door closer bottle type M.S. body with necessaryaccessories and screws complete 79 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Galvanised wire mesh of average width of aperture 1.4 mm and nominal dia of wire 0.63 mm 80 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Oxidised mild steel butt hinges 75x47x1.70 mm 81 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Oxidised mild steel handles 125 mm 82 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Oxidised mild steel tower bolt (barrel type) 200x10 mm 83 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Oxidised mild steel tower bolt (barrel type) 150x10 mm 84 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Oxidised mild steel sliding door bolt 300x16 mm 85 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Anodised Aluminium handles 125 mm with plate 175 x 32 mm 86 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Anodised Aluminium tower bolt (barrel type) 200x10 mm 87 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Anodised Aluminium sliding door bolt 300x16 mm 88 Prelaminated particle board with one side decorative and other side balancing lamination, flat pressed 3 layer & graded (medium density)Grade i, Type II conforming to IS : 12823 (exterior grade) 12 mm thick 89 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Calcium silicate tegular edged ceiling tiles 595x595 and 15 mm thick edge 90 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Float glass sheet of nominal thickness 4 mm (weight not less than 10 kg/sqm) 91 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Float glass sheet of nominal thickness 5.5 mm (weight not less than 13.50 kg/sqm) 92 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Anodised Aluminium hanging type door stopper 93 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Mild steel hooks/ Lever for glazed windows 94 Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.25 mm thick with 12.5 mm nominal size stone aggregate sqm. 95 Putty for wood work 96 Hard drawn steel wire fabric 75 x 25 mm mesh of weight not less than 7.75 kg/sqm 97 Misc. Carpentary jobs related day to day inside hospital building and residential quarters including Carpenter with Helper with tools & other materials like nails, screw etc. as per instruction of EIC. 98 Supply of Commercial Ply.Ply wood 5 ply with commercial ply on both faces 6 mm thick 99 Supply of Commercial Ply.12 mm commercial ply 100 Nickel plated bright finished mild steel piano hinges 1 mm thick 25 mm wide 101 Chromium plated Brass Wardrobe Knob 50 mm 102 Aluminium tee channel (heavy duty) with rollers and stop end 103 Oxidised M.S.casement stay (straight peg type) .300 mm not less than 0.33 kg 104 Oxidised M.S.casement stay (straight peg type) .250 mm not less than 0.28 kg 105 Float glass sheet of nominal thickness 8 mm (weight not less than 20.00 kg/sqm) 106 Providing/ Supplyingfollowing items at the site as per requirement, as per instruction of EIC.Oxidised mild steel butt hinges 100x58x1.90 mm 107 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm 108 Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. 109 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard,jointed with neat cement slurry mixed with pigment to match the shade of tiles,including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).Light shade pigment using white cement 110 Surface Preparation: Removing of Existing Old Oily/ Coatings/ Uneven particles from concrete floor by using scarifing machines , sanders , srcubing machines, wire brushes and other machanical tools. Oil contaminated areas/oil soaked areas must be degresed with the helf of specilised burning machine till the floor become bright white. After burning the floor,all the dust/dirt loose particles are to be removed & then it should be washed thoroughly by solvent cleaning/detergent washing acid cleaning finaxy by healthy wash to be given with water. make the entire area dry with the help of high capacity vaccum cleaner and hot air blowers. grinding machine is used to give the surface level.this process must be repeated upto satifaction of site/engineer in charge to ensure permisible limit of moisture and oil content 111 Application of concrete primeris apllied to the surface. The application of primer is done by means of roller/manually for thickness of 200 microns, primer given the good medium of bonding to the substrata. Primer coat is allowed to get tack free before applicationof Heavy duty industrial screed mixing ration of primer is 2.1 112 Application of top coat with self levelling compound. As per the requirment once the floor is ready with screeding & intermediate coat after getting complete cure. Dust dirt has to be removed from the surface. Once it is ensured that the surface is ready to apply the top coatthe materialhas to be mixed in the proper proportion & is to be applied properly . The levelling compound .During application movement should be aplication is over it should be kept .for 24 hrs. for functional cure depents upon the amblient temp. flexural strenght is 27.0 Mpa. This given the monolithic semless floor. It does not allowed the soaking of oli/water mineari any type of liquids fungal or becterial growth self levelling compound can be applied from 1 mm to 1.2 mm thicknes the floor is allowed for 24 hour funvtional cure. 113 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm 114 Trimming of trees and up rooting of unwanted plants and hrubsupto girth 25 cm up to floor V level with all tools and plants required in wall slab, chajja etc. in shape wherever required with safety precautions and making good the same with plaster as per instruction of EIC including disposal of material/tree roots etc. at the required place all complete. 115 Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting ofjoints (Payment for grouting of joints to be made separately).Size of Tile 800x800 mm 116 Total impact of GST for the purpose of CTC
