Tender For Special repair To Rb Judge Under Mtc Booth Sector 16, Chandigarh.-- 1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 2 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of sizeSize of Tile 600 x 600 mm 3 Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 4 1:5:10 (1 cement : 5 coarse sand (zone-Ill) derived fromnatural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 5 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4(1 cement : 4 coarse sand) : 25 mm thick 6 Providing and fixing 2nd class teak wood(kiln seasoned) chowkhat 4 1/2 x 2 1/4including cost of corner straps, iron hold fasts, hinges, screws,nails, fevicol etc. and spirit polish of chowkhats. Rate includes the cost of dismantling of all damaged chowkhats and making good the damage to walls plaster and floors as required including, disposal of rubbish to the dumping ground the rate further includes the cost of two coats Spirit polish complete in all respect and to the entire satisfaction of Engineer-in-Charge 7 Providing and fixing 4mm thick plain glass panes with beading when required over exixting chowkhat or fixed shutter or fixed portion or glazed shutter including the cost of nails, putty etc.complete in all respect to the entire satisfaction of Engineer-in-charge. 8 Providing and fixing wooden cabinet of 13½” deep and 2’-0 height with openable shutter at wall above 4’-9 height consisting of 18mm thick pre-laminated (one side decorative and other side balancing lamination), flat pressed 3 layer or graded particle board (medium density),Grade I, Type II, IS: 12823 marked (exterior grade) lipped with hard wood lipping of size 18mm x 6mm on exposed edges include cost of piano hinges and handles, magnetic catchers, nails, screws, synthetic adhesive etc. and fixed in position with help of fastners at wall complete in all respect to the entire satisfaction of Engineer-in-charge 9 Providing and fixing of kitchen cabinet below working shelves made out with 19mm thick commercial ISI marked plyboard and front portion of the cabinet furnished with 1mm thick superior quality sun mica of outer side and 0.8mm thick sun mica inner side of the cabinet for fixing the kitchen accessories and jack at bottom synthetic enamel paint over remaining portion. It is also include the cost of sprit polishing on the edge of the lipping cost of stainless steel handle, adhesive, nail, screws etc. complete fixed in position to the entire satisfaction of Engineer-in-Charge. 10 Providing and fixing 15- 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 11 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 12 Providing and fixing S.S. 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. 13 Providing and fixing heavy duty telescopic channel for drawers 18 to be fixed with necessary screws complete in all respects and to the entire satisfaction of the Engineer in charge.
