Tender For Renovation Of Comman Washroom ( Male And Female ) Near Dining Hall At Vh-1 - EARTH WORK 2 Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: 3 All kinds of soil 4 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 5 Surface dressing of the ground including removing vegetation and in- equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. 6 All kinds of soil 7 CEMENT CONCRETE (CAST IN SITU) 8 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness)includingattachedpilasters,columns,piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 9 1:2:4 (1Cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 10 Makingplinthprotection 50mmthickofcementconcrete 1:3:6 (1cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 11 REINFORCED CEMENT CONCRETE 12 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 13 Centering and shuttering including strutting, propping etc. and removal of form for 14 Shelves (Cast in situ) 15 Lintels,beams,plinthbeams,girders,bressumersand cantilevers 16 Steelreinforcement forR.C.C.workincludingstraightening,cutting, bending, placing in position and binding all complete above plinth level. 17 Thermo-Mechanically Treatedbars of gradeFe-500D or more. 18 MASONRY WORK 19 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 20 Cement mortar 1:6(1 cement : 6 coarse sand) 21 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 22 Cement mortar 1:4(1 cement :4 coarse sand) 23 Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). 24 CLADDING WORK 25 Providingandfixing 18mmthickgangsawcut,mirrorpolished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters,window sills,facias andsimilar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. 26 Granite stone slab of all colour and texture except black, Cherry/Ruby red 27 Area of slab over 0.50 sqm 28 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 29 Granite work 30 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 31 WOOD AND P. V. C. WORK 32 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 33 Second class teak wood 34 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. 35 Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4 mm wide aperture with matching wood beading 36 Extra for providing frosted glass panes 4 mm thick (weight not less than 10 kg per sqm) instead of ordinary float glass panes 4 mm thick (weight not less than 10 kg per sqm) in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). 37 Providing and fixing ISI marked flush door shutters conforming to IS : 2202(PartI)non-decorative type,core of blockboardconstruction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 38 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 39 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 40 Providing and fixing bright finished brass butt hinges with necessary screws etc. complete: 41 100x70x4 mm (ordinary type) 42 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 43 250x10 mm 44 200x10 mm 45 Providingand fixingbright finishedbrass door latch withnecessary screws etc. complete : 46 300x16x5 mm 47 Providingandfixingbright finishedbrasshandleswithscrewsetc. complete: 48 125 mm 49 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. 50 Providingand fixingaluminiumdie cast body tubular typeuniversal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 51 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 52 300x10 mm 53 250x10 mm 54 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 55 125 mm 56 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 57 1.0 mm thick 58 Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge. 59 200 mm 60 FLOORING 61 Providing and laying Vitrified tiles in floor in diferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 62 Double charge vitrified tile polished finish of size 63 Size of Tile 600 x 600 mm 64 Size of Tile 600 x 1200 mm 65 ProvidingandlayingVitrified tilesindiferent sizes (thickness tobe specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). 66 Size of Tile 600x600 mm 67 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. 68 Size of Tile 600x600 mm 69 Size of Tile 1000x1000 mm 70 FINISHING 71 12 mm cement plaster of mix: 72 1:6 (1 cement: 6 coarse sand) 73 15 mm cement plaster on rough side of single or half brick wall of mix: 74 1:6(1 cement: 6 coarse sand) 75 6 mm cement plaster of mix: 76 1:3(1 cement :3 fine sand) 77 French spirit polishing : 78 Two or more coats on new works including a coat of wood filler 79 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 80 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approvedbrandandmanufacture,includingapplyingadditionalcoats wherever required to achieve even shade and colour. 81 Two coats 82 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 83 Painting with aluminium paint of approved brand and manufacture to give an even shade: 84 One or more coats on old work 85 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade 86 Old work (Two or more coats applied @ 1.43 V/ 10 sqm) over existing cement paint surface 87 REPAIRS TO BUILDING 88 Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in- charge. 89 Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge. (a) Internal Work- Exposed on wall 90 Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. 91 Dismantling and Demolishing 92 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 93 Nominal concrete 1:3:6 or richer mix (including equivalent design mix) 94 Nominal concrete 1:4:8 or leaner mix (including equivalent design mix) 95 Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. 96 Demolishingbrickworkmanually/bymechanicalmeansincluding stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 97 In cement mortar 98 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 99 Of area 3 sq. metres and below 100 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 101 For thickness of tiles 10 mm to 25 mm 102 Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. 103 Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead : 104 100 mm dia pipe 105 Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge : 106 15 mm to 40 mm nominal bore 107 Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. 108 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 109 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. 110 SANITARY INSTALLATIONS 111 Providing and fixing soil, waste and vent pipes : 112 100 mm dia 113 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 114 75 mm diameter : 115 Centrifugally cast (spun) iron socketed pipe as per IS: 3989 116 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 117 100 mm dia 118 Sand cast iron S&S as per IS - 3989 119 Providing and fixing plain bend of required degree. 120 100 mm dia 121 Sand cast iron S&S as per IS : 3989 122 Providing and fixing collar : 123 100 mm 124 Sand cast iron S&S as per IS - 3989 125 75 mm 126 Sand cast iron S&S as per IS - 3989 127 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 128 100 mm 129 75 mm 130 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 131 100 mm inlet and 100 mm outlet 132 Sand cast iron S&S as per IS: 3989 133 100 mm inlet and 75 mm outlet 134 Sand cast iron S&S as per IS - 3989 135 Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litre with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. 136 WATER SUPPLY 137 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.Internal work - Exposed on wall 138 15 mm dia nominal bore 139 20 mm dia nominal bore 140 25 mm dia nominal bore 141 32 mm dia nominal bore 142 Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, including making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 143 15 mm dia nominal bore 144 20 mm dia nominal bore 145 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.External work 146 25 mm dia nominal bore 147 32 mm dia nominal bore 148 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 149 25 to 40 mm nominal bore 150 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 151 25 mm nominal bore 152 20 mm nominal bore 153 32 mm nominal bore. 154 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 155 25 mm nominal bore 156 Providing and fixing uplasticised PVC connection pipe with brass unions : 157 45 cm length 158 15 mm nominal bore 159 Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in reinforced cement concrete slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : 160 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 161 Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): 162 15 mm nominal bore 163 20 mm nominal bore 164 25 mm nominal bore 165 32 mm nominal bore 166 Providing and fixing C.P. Brass extension nipple (size 15 mm x 50 mm) of approved make and quality as per direction of Engineer-in-charge. 167 Cutting holes up to 30x30 cm in walls including making good the same: 168 With common burnt clay F.P.S. (non modular) bricks 169 Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc. 170 DRAINAGE 171 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 172 150 mm diameter 173 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 174 150 mm diameter S.W. pipe 175 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 176 150 x 100 mm size P type 177 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 178 Dismantling of old S.W. pipes including breaking of joints and bed concrete stacking of useful materials near the site within 50 m lead and disposal of unserviceable materials into municipal dumps : 179 100 mm diameter 180 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 181 For pipes 100 to 250 mm diameter 182 Sub-Total 183 ALUMINIUM WORK 184 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) : 185 For fixed portion 186 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) 187 Forshuttersofdoors,windows&ventilatorsincluding providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 188 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) 189 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 190 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) 191 Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. 192 Upto 5 mm depth and 5 mm width 193 Extra for applying additional anodic coating AC 25 instead of AC 15 to aluminium extruded sections. 194 For fixed portion 195 For shutters of doors, windows & ventilators 196 MINOR CIVIL MAINTENANCE ITEM 197 Providing and laying cementconcrete of specified grade i/c the cost of centring and shuttering, All work upto plinth level. (1 cement :5 coarse sand : 10 graded brick aggregate 40 mm nominal size). 198 Providing and fixing aluminium door sea 3 feet long with screws etc. 199 Providing and fixing white vitreous china flat back or half stal urinal of 580 x 380 x 350 with standard size C.P brass flush pipe,spreader with union and clamps and c.p brass push cock 15 mmi/c cutting and making good the walls. (a)Range of single half stal urinal. 200 Providing and fixing white vitreous china oval type wash basin of size 550 x 480 Cera make Cat no 2030125. 201 Providing and fixing C.P coat pin hanger of approved make with necessary srews gully etc. cera make cat no 5015108 202 Providing and fixing c.p. brass Urinal flush valve Auto closing System with Built-in Control cock & wall flange of (Jaguar make) code no PRS-077 15 mm nominal bor. 203 Providing and fixing looking mirror of 5.5 mm thick superior glass of approved quality complete with 12 mm thick of water type ply wood sheet ground 40 mm widex 12 mm thick 1st class teak wood beading frame of half round fixed to wooden cleats with C.P brass scerw and washer complete. teak wood beading finished with sprits polishing copmplete. 204 P/F C.P Brass flange for angle valve, bib cock etc. ( Heavy type ) 205 Providing and fixing c.p. hand spray ( health faucet )with push button control and fleexible hose connection with c.p. hook complete in all respects. ( Cera make ) Cat No 8030105 AB. 206 Providing and fixinganti cocroach grating 125 mm dia approved equivalent make. 207 Providing and fixing c.p. brass angle valve of (Jaguar make) code no 053 KN 15 mm nominal bor. 208 Providing and fixing c.p. brass Towel Ring with round flange of (Jaguar make) code no. CAN-1121BN 209 Providing and fixing C.P.waste 32 mm dia for wash basin/Sink. 210 Providing and fixing C.P.. brass central hole basin mixer without popup waste system with 450 mm long copper pipes & nuts etc. of (Jaguar make) code no. 167 KNB 211 Providing and fixing c.p. brass soap dish of ( Jaguar make ) code no 1531. 212 Extra for vitrified tiles 600*600 mm work for wall lining on Full height wallsfrom Floor level level to ceiling height. 213 Dismentling broken wash basin /kitchen sink with old worn out bracket and cleaning of waste water pipe up to trap. 214 Dismantling of C.I pipe with fittings and clamps i/c disposal of unserviceable material up to 50 mtr. lead and upto 150 mm dia. pipe. 215 Providing and fixing Stainless SteelGrab Bar 450mm longof (Jaguar make) code no AHS- 1501. 216 Providing and fixing c.p. brassShort body bib Cock with wall flange of (Jaguar make) code no CON- 037 KN 15 mm nominal bor 217 Providing and fixing c.p. brass bottle trap with internal partition 32 mm Size with 300mm &190 mmlong wall connection pipes of (Jaguar make) code no769B . 218 Providing and fixing c.p. brass Toilet roll holder with flap of (Jaguar make) code no. CAN- 1153 N. 219 Providing and fixing c.p. brass single Towel Rail 600 mm longof (Jaguar make) code no CAN- 1111NM
