Tender For Pay And Use Jsc. Renovation And Up-Gradation Of Existing 16 Seater Jsc (Code No-18Cj1026) At Khilona Wala Bagh Ac-18 Model Town. (Pid No.15665).- 1 Demolishing cement concrete manually/ by mechanical means includingdisposal of material within 50 metre lead as per direction of Engineer- in- charge : Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 2 Demolishing cement concrete manually/ by mechanical means includingdisposal of material within 50 metre lead as per direction of Engineer- in- charge :Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) 3 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer- in- charge. In cement mortar 4 Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in:Channels, angles, tees and flats 5 Dismantling stone slab roofing over wooden karries or R.C.C. battens (dismantling karries and battens to be paid for separately), including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. 6 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below 7 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead 8 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) 9 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V Cement mortar 1:4 (1 cement :4 coarse sand) 10 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 11 Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces 12 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 13 Providing sand stone slab for roofing and laying them in cement mortar 1 : 4 (1 cement : 4 coarse sand) over wooden karries or R.C.C.battens or structural steel sections (Karries or battens or structural steel sections to be paid separately), including pointing the ceiling joints with cement mortar 1:3 (1 cement : 3 fine sand ) complete : Red sand stone slab 40 to 50 mmthick 14 Providing and laying in position ready mixed plain cement concrete, using fly ash and cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge.sand and aggregate derived from natural sources. Note : (1) Excess/less cement used than specified in this item is payable/ recoverable separately. (2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS : 456. Uniform blending with cement is to be ensured in accordance with clauses 5.2 and 5.2.1 of IS: 456 -2000 in the items of BMC and RMC.All works upto plinth level: M-15 grade plain cement concrete (cement content considered @ 240 kg/cum) cum 6066.50 15 Neat cement punning 16 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete 17 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete 18 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cementmortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick 19 6 mm cement plaster of mix :1:3 (1 cement : 3 fine sand) sqm 20 12 mm cement plaster of mix: 1:6 (1 cement : 6 fine sand) 21 15 mm cement plaster on the rough side of single or half brickwall of mix: 1:6 (1 cement : 6 fine sand) 22 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 23 Providing and fixingtrap of self cleansing design with sand cast iron screwed down or hinged gratting with or with out vent arm complete including cost of cutting and making good the wall & floors - 100mm inlet and 100 mm outlet Sand Cast Iron S & S as per IS-1729 24 White washing with lime to give an even shade : New work (three or more coats) 25 Providing and fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with nuts and screws etc. complete : 150 X 10 mm 26 Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed of required colour and shade, with necessary screws bolts, nut and washers etc. complete. 27 Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 100 mm 28 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. 29 Providing and fixing soil, waste and vent pipes 100 mm dia. Sand cast iron S & S pipe as per IS: 1729 30 Providing and filling the joints with spun yarn cement, slurry andcement mortar 1:2 ( 1 cement: 2 fine sand) in S.C.I/C.I pipes 100 mm dia pipe 31 Providing and fixing M.S. holder bat clamps of approved design to sand cast iron / cast iron ( spun ) pipe embedded in and including cement concrete blocks 10 X 10 X 10 cm of 1:2:4 ( 1 Cement : 2 Coarse Sand : 4 graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls for 100 mm dia pipe 32 Providing and fixing plain bend of required degree 100 mm Sand cast iron S&S as per IS-1729 33 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fiitings, including fiximg the pipes with clamps at 1.00m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. Internal work - Exposed on wall15 mm nominal outer dia Pipes 34 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fiitings, including fiximg the pipes with clamps at 1.00m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge.. Internal work - Exposed on wall20 mm nominal outer dia Pipes 35 Providing and fixing PTMT bib cock of approved quality and colour. 15mm nominal bore, 86 mm long, weighing not less than 88 gms 36 Providing and fixing PTMT stop cock of approved quality and colour. 20 ‘mm nominal bore, 89 mm long, weighing not less than88 gms 37 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.Circulsr Tank 38 Dismantling of manhole including R.C.C. top slab, C.I. cover withframe including stacking of useful materials near the site anddisposal of unserviceable materials into municipal dumps within50 m lead: Rectangular manhole 90 x 80 cm and 45 cm deep 39 Dismantling of old S.W. pipes including breaking of joints and bed concrete stacking of useful materials near the site within 50 m lead and disposal of unserviceable materials into municipal dumps : 100 mm diameter 40 Dismantling of old S.W. pipes including breaking of joints and bed concrete stacking of useful materials near the site within 50 m lead and disposal of unserviceable materials into municipal dumps : 300 mm diameter 41 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :100 mm diameter metre 42 Lowering ,laying and jointing of class SNB structure wall ( External Annular corrugated & smooth internal surface ) polyethylene piping & fitting with the help of ( One line / offline) attached with one end of pipes: sliding over the elastomeric sealing rubber ring placed on the specified valley of the corrugation at the spigot end lowering the same into the trench laying on the lower bedding ( Constructed at bottom of trenches) at prescribed gradient , depth & alignment testing the water tightness of the joints , ensuring the continuity tests of specified pipe segments etc complete as per drawing, specifications & detailed engineering, including carriage of pipe & fittings from site stacks to the place of laying etc as per direction of engineer-in -charge 250 mm inner diameter & 295 mm outer diameter 43 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 100 mm diameter S.W. pipe metre 44 Distempering with dry distemper of approved brand and manufacture(two or more coats) of required shade on new work, over and includingwater thinnable priming coat to give an even shade. sqm 71.85 45 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 46 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 47 Constructing brick masonry manhole in cement mortar 1:4( 1 cement : 4 coarse sand ) R.C.C. top slab with 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size ) inside plastering 12 mm thick with cement mortar 1:3( 1 cement : 3 coarse sand ) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard designInside size 90 x 80 cm and 45 cm deep including C.I. cover withframe (light duty) 455 x 610 mm internal diamensions total weightof cover and frame to be not less than 38 kg (weight of cover 23kg and weight of frame 15 kg)- With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 48 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid 49 Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 0.91 m deep with SFRC cover and frame (heavy duty, HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 50 Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 51 Providing and laying in position cement concrete of specified grade excludingthe cost of centering and shuttering - All work up to plinth level :1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stoneaggregate 40 mm nominal size). 52 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 250 to 300 mm diameter 53 Disposal of building rubbish / malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. 54 Extra for every additional lead of 50m or part thereof beyond first 50m upto 9 such additional leads Lime, moorum building rubbish 55 Deduct for not Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixturescomplete.10 litre capacity - White 56 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. sqm 57 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work 58 Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 59 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :In 75x75 mm deep chase 60 24 mm thick washed marble chips plaster on exterior walls of height upto 10 m above ground level in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 kg of cement per sqm, top layer 12 mm thick cement marble chips plaster 4:7 (4 cement :7 marble chips 4 mm size) in panel with grooves alround as per approved pattern including scrubbing andwashing the top layer with brushes and water to expose the marble chips complete as per specifications and directions of Engineer-in-charge (Payment for providing groove shall be paid for separately). 61 Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the Engineer-in-Charge. 62 Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied@ 2.20 kg/10 sqm) 63 Providing and fixing Stainless Steel hanger 150 mm long, 25 mm width of weight not less than 90 grams of approved quality. Fixing to be done by drilling holes with necessary plastic plug and stainless Steel screws 40 mm long on walls or glazed tiles surface complete as per directions of Engineer -in-charge. 64 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 65 Providing and supplying of class SN8 structured wall polyethylene piping system ( Pipe with online/off line ) coupler & elastomeric sealing ring ) with non-smooth External Annualcorrugated and smooth internal surface ( Double Wall ) for non pressure underground sewerage& drainage application as per EN: 13476-3/IS:16098 ( Part-2): 2013 including all local and central taxes, transportation , flight charges action inspection charges loading unloading conveyance to the departmental stores etc complete 250 mm diameter and 295 mm outer diameter 66 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washerscomplete. 67 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position andapplying a priming coat of approved steel primer all complete. 68 Add for cost index @31.27 %as per order by GNCTD except item no.42 & 65. 69 Deduct 9.50% as per GNCTD 70 Less for Salvage Value (Steel)
