|
| 1 | Sub Head - I (EI Works) |
| 2 | S/I/T/C of Magnetic track linear spotlight for Rue Slim with LED (Light Emitting Diode) system power: 12W, luminous flux of luminaire 960lm, colour temperature of 4000K, Neutral white, CRI>80,24V DC,direct light emission, beam angle of 36deg aluminium housing polyester Black powder coat applied over a 5- stage pretreatment, Dali Control Gear Protection class II, IP20 L = 327 mm, B= 22 mm, H = 44 mm. etc. complete as reqd. |
| 3 | S/I/T/C of Non LED Rescessed Rue - Track (With Trim) Without Luminary Element Aluminium Optics: Without Diffuser Finish: Black Control Gear: Electronic Control Protection Class: II IP 20 L:1000mm, B:26.2 mm, H: 52 mm etc. complete as reqd. |
| 4 | S/I/T/C ofCOB based recessed downlight luminaire Amber, System power:12W, Luminous flux of luminaire 1200lm, Colour temperature of 4000K, Neutral white, CRI>80, 230 V constant current driver, 70% of luminous flux after 50,000 operating hours; Energy-efficient COB, Direct light emission, Luminaire housing in aluminium, Polyester powder Black coloured coat applied over a 5-stage pre-treatment ceiling trim, Lens with anti glare reflector UGR <16 and a beam angle of 38°, ZHLS (ZERO HALOGEN LOW SMOKE) wiring, Electronic control gear Protection class II, IP 20 Ø = 85 mm, H =100 mm etc. complete as reqd.\" |
| 5 | S/I/T/C of Surface mounted LED strip (flexible) , 2835 SMD package with a thermal tape with high thermal conductivity, system power: 15 W/metre, luminous flux 1200lm, colour temperature of 4000K, CRI>80, Anodized aluminium extrusion, Opal diffuser, 12V DC, constant voltage driving circuit,electronic control gear. IP20 L-1000m etc. complete as reqd. |
| 6 | S/I/T/C of Recessed wall washer Link W with LED(Light Emitting Diode) system power: 20W, luminous flux of luminaire 1300 lm, colour temperature of 4000K, neutral white, CRI>80, 230V constant current driver, 70% of luminous flux after 50,000 operating hours, energy efficient LEDs, direct light emission, support profile in aluminium powder coated white, reflector for asymmetric light throw with linear prismatic diffuser, electronic control gear, Protection class II, IP20, L=280mm, B = 45mm,H = 50mm, cutout = 275 mm x 40 mmetc. complete as reqd. |
| 7 | Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required. |
| 8 | Group C |
| 9 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 10 | Group C |
| 11 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. |
| 12 | 3 x 1.5 sq. mm |
| 13 | 3 x 4 sq. mm |
| 14 | 3 x 6 sq. mm |
| 15 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 16 | 5/6 amps switch |
| 17 | 15/16 A switch |
| 18 | 3 pin 5/6 A socket outlet |
| 19 | 6 pin 15/16 A socket outlet |
| 20 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 21 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 22 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 23 | 3 Module (100 mmX75 mm) |
| 24 | 6 Module (200 mmX75 mm) |
| 25 | 8 Module (125 mmX125 mm) |
| 26 | 12 Module (200 mmX150 mm) |
| 27 | Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. |
| 28 | 20 mm |
| 29 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 30 | 20 mm |
| 31 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) |
| 32 | 4 way (4 + 12), Double door |
| 33 | 8 way (4 + 24), Double door |
| 34 | 12 way (4 + 36), Double door |
| 35 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator). i) 2 + 4 way/ 6 way, Double door |
| 36 | Supplying and fixing Cable End Box (Loose wire box)(IP 43) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with testing and commissioning etc. as required. |
| 37 | For 8 way, Double door SPN MCBDB |
| 38 | Supplying and fixing 5 amps to 32 amps rating 240 volts \"C\" curve miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections , testing and commissioning etc. as required. |
| 39 | Single pole |
| 40 | Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps \"C\" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 41 | Supply, Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R- 407 Green Refrigerant, wireless Remote control, suitable for working between 180-260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 Degree Celsius. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electro technical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient temperature). Inverter Type - Cooling only |
| 42 | 1.5 TR with 5 Star BEE Rating |
| 43 | 2.0 TR with 5 Star BEE Rating |
| 44 | Supplying, installation, Testing & Commissioning of LED Recessed / surface Down lighter (Round / square/ Rectangular) COB Type of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140- 270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), life time of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. \"complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast /Extruded aluminium Body including trim with Aluminium Reflector. |
| 45 | 12 -15 watt |
| 46 | Supplying, installation, Testing & Commissioning of LED Recessed / surface Down lighter (Round /square/Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS: 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltag AC 140-270 Volt, freq 50/60 hz, Operating temp range - 15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), life time of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K / 6000°K /6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast / Extruded aluminum Body including trim. |
| 47 | 12 -15 watt |
| 48 | Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., offollowing body material and construction as per IS : 10322 with driver as perthe requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuitprotection, THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified GlareRating) < 19, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K/6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation ColorMatching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade markcertificate (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumenefficacy >135 lm/Watt output . LM79 & LM80 Test report from NABL labfor all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast / Extruded aluminium Body (Thickness ≥ 1.20 mm) |
| 49 | 36 watt |
| 50 | SH:- II (Water level Controller System) |
| 51 | Supply, installation, testing, and commissioning of a microcontroller based wireless controller system designed for managing water levels and pressure across multiple remotely situated tanks. The wireless controller communicates on 865~868Mhz band for long range communication. This control system integrates microcontroller technology with wireless data reception capabilities to receive various sensor data wirelessly to indicate & control water automation system. It will indicate water level in Percentage with One percent resolution alongwith tank ID through 4-digit LED/LCD display (minimum 56mm height) for real-time visualization of water levels and sensor data, alongside four potential-free relays that enable the system to operate single or dual motors (three-phase) based on specific conditions. The controller starts the motors when water levels in any linked tank drop below predetermined thresholds and stopping them when all tanks reach capacity. It also responds to data from pressure transmitters, ensuring motors operate within defined pressure ranges in pipeline. It must have a built-in RTC with timer functions, enabling automated motor control based on configurable schedules, while providing comprehensive runtime statistics for monitoring purposes. There should be an audio & visual alarm, if water level in any tank cross threshold limit for overflow level. It should also give visual indication for various fault conditions. Operating voltage single phase 180~260Vac. It can also indicate status of motorized valve and minimum number of opened valves can be set beyond which it will stop the motor to avoid excessive pressure in pipeline. It will also indicate rising/ falling trend of water level in overhead/ underground tank. |
| 52 | It should have RS 485/Modbus output to interface with Variable Frequency Drives (VFDs), Building Management Systems (BMS), and Remote Terminal Units (RTUs) to ensure seamless integration within larger infrastructure frameworks and facilitates data exchange on water levels, motor statuses, sensor configurations, and operational commands. It should be capable to change internal setting through modbus from RTU/ BMS system. The controller\"s enclosure should be made from minimum 0.80mm thick MS sheet with a powder-coated finish and a 3mm thick polycarbonate sheet protecting the display area. It must confirming to standards for fire hazard (IEC 60695- 2-10:2021) and ingress protection (IP65 per IS/IEC 60529:2001), ensuring reliability in various environmental conditions. It should have suitable fixing/ mounting arrangement. |
| 53 | Supply, Installation, Testing & Commissioning of Battery operated (to power minimum 8Year) RF based ultra low powered wireless water level data sump transmitter (minimum 15dBm power) operating in frequency band 865~868mHZ, confirming to EN 300 220 and ingress protection IP68, with scale and corrossion free capcitance based level sensor to measure water level percentage from 0% to 100% (± 5% with 1% resolution for tanks upto 10mtr depth with auto calibration sensor. It should also calculate trend & rate of rise/ fall of water level and transmit the data alongwith water level data. It will have input for detection of conductivity based flow in pipeline and on/off status of motorized valve and send the data wirelessly. It should have a technique to avoid collision of RF signal and minimise corruption of data. It should have CRC check in transmitted data to detect error in block of data. |
| 54 | Supply, Installation, Testing & Commissioning of Battery operated (to power minimum 8Year) RF based ultra low powered wireless water level data top transmitter (minimum 15dBm power) operating in frequency band 865~868mHZ, confirming to EN 300 220 and ingress protection IP68, with scale and corrossion free capcitance based level sensor to measure water level percentage from 0% to 100% (± 5% with 1% resolution for tanks upto 10mtr depth with auto calibration sensor. It should also calculate trend & rate of rise/ fall of water level and transmit the data alongwith water level data. It will have input for detection of conductivity based flow in pipeline and on/off status of motorized valve and send the data wirelessly. It should have a technique to avoid collision of RF signal and minimise corruption of data. It should have CRC check in transmitted data to detect error in block of data. |
| 55 | Supply, Installation, Testing & Commissioning of 230Vac/ 5V DC operated RF signal booster operating in Frequency band 865~868mHZ confirming to EN.300.220 to relay/ transmit the RF signal received from multiple transmitters to further distance with LED based instant indicator. It should have a technique to avoid collision of RF signal and minimise corruption of data. A mechanism should be there to avoid circular transmission of data between repeaters. LED based visual indication should be there to indicate signal strength of received wireless data. It should have RF receiving sensitivity of minimum -125dBm and transmission power of minimum 15dBm. It should be configurable to filter out RF signal of particular transmitters to reduce the transmission signals in Air. It should have shock proof ABS body with IP65 rating and must have suitable mounting arrangements on wall or stand. |
| 56 | Supply, Installation, Testing & Commissioning of 12V DC operated wireless RTU to receive data wirelessly from remote sensor data tansmitters/ RF boosters and push the data to BMS/ controller unit through UART and to the server through 4G/ 5G GSM network. This device will be equipped IOT sim of cellular network service providers. It should have LCD/ OLED screen to display various parameters and status of network/ connectivity. The enclosure should be IP65 rating with suitable mounting arrangements. Various settings should be configurable through common web browser using wifi feature. |
| 57 | Supply, Installation, Testing & Commissioning of Web based remote monitoring/ control system: Providing web based remote Water level monitoring/ control system by providing access to controller/ information panel at Central server of minimum Tire-III level data centre in India. It will indicate various data/ parameters in user friendly manners. It will also show data in graphical/ CSV format which can be downloaded. Various parameters full, low and overflow limits of individual tanks can be configured through this web interface. Other parameters related to operation of motor can also be configured remotely. It can be access through any web browser with multi-level user authentication. It will trigger SMS alerts for various events on crossing limits, to multiple mobile numbers. The cost include only for access to server/ application and it does not include the cost of required hardware. The cost of hardware will be charged separately but the cost of running the services is included. For access to Motor controller/ Valve Controller - For 12 months |
| 58 | Supply, Installation, Testing & Commissioning of Float Valve/ Ball Cock: Providing fixing and installation of PTMT Float Valve with powder coated aluminium rod & L.P./ H.P.H.D. plastic ball in Existing Water tanks including cutting/ threading existing water supply line and providing and fixing of required GI/CPVC/UPVC fittings (Elbow, Socket, Bush, reducer) complete. - 25mm dia NB |
| 59 | Supply, Installation, Testing & Commissioning of Aquabrim\"s Water Level Controller Unit including Fixing of Controller, Transmitter and other Accessories within the premises. |
