Tender For Repair For Boundary Wall And Other Works In Hcm Ripa - 1 Dismantling Old Plaster Or Skirting, Raking Out Joints And Cleaning The Surface For Plaster Including Disposal Of Rubbish To The Dumping Ground Within 50 Meter Lead.(B-14.55) 2 Demoli

Sharing tender

Tender For Repair For Boundary Wall And Other Works In Hcm Ripa - 1 Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead.(B-14.55) 2 Demolishing cement concrete mix 1:3:6 or rich manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge.(B-14.2.1) 3 Demolishing stone rubble masonry inn Cement mortar manually/ by mechanicalmeans including stacking of serviceable material and disposalof unserviceable material within 50 metres lead as perdirection of Engineer-in-charge.(B-14.9.2) 4 Dismantling tile work 10mm to 20mm thick in floors and roofs laid in cement mortarincluding stacking of serviceable material and disposal ofunserviceable material within 50 meter lead.(B-14.23.1). 5 Dismantling precast concrete or stone slabs 40mm to 75mm thick in wall partitions etc. including stacking within 50 meter lead.(B-14.40.2). 6 Dismantling wooden boards 10mm to 25mm thick in lining of walls and partition excluding supporting members but including stacking within 50 meter lead.(B-14.39.2). 7 Mechanised cleaning of storage tanks above 1000 ltr comprises of following 6 stage as mentioned below :(i) Mechanical dewatering(ii) Desalting removal of leftover dirty water and sludge with sludge pump(iii) Cleaning of wall, ceiling and floor by high pressure water jet with help of equipments which creates a pressure of 100-150 bar(iv) Removal of remaing sludge from floor with the help of industrial vacum cleaner.(v) Spraying of non toxic, bio degradable ecofriendly and bacterial agent certified by a govt approved laborary to disinfect the tank from all harmfull pathogens. The dose should be safe as per the UECD guidelines & 23 adopted on 17 th december 2001.(vi) Treatment of inside tank by exposing UV radiation to kill further suspended or floating bacteria if any (B-13.32.3). 8 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) 40mm thick with 20mm thick nominal size aggregate finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete(B-11.3.1) 9 Providing and laying in position cement concrete M10 grade Nominal Mix1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.(B-3.1.5) 10 Supplying and fixing stone liri 6 cm. to 9 Cm thick including finsing face joint with white cement moartar and matching pigment in CM 1:4 work facing with proper projection and chiesel dressing of edges of stone two line dressing of building corners, jambs etc. including uniform joints using aluminium square section of size 12 mm to 15 mm as per requirement of course and width of stone not less than 12 Cm., with requisite number headers (minimum length of stone 0.9 M) 6 cm. to 9 Cm. thick. (B-6.72(i) 11 Labour charges for Animar dressing (old M.G.H. pattern) over Soorsagar or equivalent white Ashlar over already two line dressed surface by using special tools i.e. toothed chisel etc.(B-6.67) 12 Random Rubble stone masonry Cement Mortar 1:6 ( 1-Cement : 6-Sand) with hard stone in superstructure above plinth level and upto five level above 30cm. thick walls in.(B-6.2.6). 13 Plaster on new surface on wall in cement sand mortar 1:4 including racking of joints etc. complete fine finish :20mm thick.(B-12.2.2) 14 Finishing with neat cement (punning).(B-12.7) 15 Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. 16 Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green,light blue and other light shades in floors, steps, pillars etc.laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 17 Providing and fixing 1st quality standard white, grey, ivory,fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in thewhite cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 18 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor. With Chlorpyriphos/Lindane E.C. 20% with 1% concentration(B-1.35.3) 19 Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes atdownward angle of 45 degree at 150mm centre to centre and sealing the same. With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 20 Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/Lindane emulsifiable concentrate of 20% (B-1.34) 21 Providing and fixing wall panelling 12 mm thick one side laminated board Practical board (Phenol bonded) using soft wood frame of size 50x25mm @600 mm c/c in both directions duly treated with anti-termite treatment making grooves painting of grooves specification and drawing using ( B-8.20.4). 22 Structural steel work in single section fixed with or without connecting plate including cutting, hoisting ( height upto 10 m), fixing in position and applying a priming coat of approved steel primer all complete.(B-9.1.1) 23 Providing and fixing M.S. sheet 1mm thicksingle leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint(B-9.17) 24 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge) includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :(B-10.22) 25 Nano technology water proofing, thermal insulation protection coating 9 layer process for increasing life of building and damage control protection for walls.-- before coating scaling,cleaning, and preparing surface for treatment. Opening all joint and cracks and filling them with nano technology crack filling hydrophobic chemical with 2 coats. then after drying doing a PCC coat on cracks. One coat of nano technology hydrophobic/oiliophobic primer. Nano technology water proofing treatment in 2 coats non silicon based thermal insulation coating highly elasticity in nature with 2 coats with 1000 micron thickness 2 top coats of anti slippery, natural transparent high shine chemical for better life of the treatment (B-15.28.2). 26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete(B-12.23) 27 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding:Two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect.(B-12.40.1) 28 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding:One or more coats on old work including prepartion of base with primer, putty, lippy etc complete in all respect.(B-12.40.2) 29 Painting with synthetic enamel paint of approved brand and manufacture togive an even shade : Two or more coats on new work(B-12.46.1) 30 Painting exterior surface ofWallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect including scaffolding and safety provision. Old Work(B-12.43.2) 31 Extra for providing frosted glass panes instead of ordinary float glass panes in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).(8.7 (a)) 32 P & F European type white glazed vitreous china 1st quality Double syphonic W.C (IS :2556 Mark) with P or S trap including cutting and making good the wall and floor (S-1.4) 33 P & F water closet Seat Covers Solid PVC (IS 2548 marked) grade-I Coloured for EWC with brass hinges complete (S-1.7.5). 34 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make110mm dia,(S-3.44.1)