Providing & Fixing Furniture, For Canteen, Conference And Committee Room, Mobile Storage And Civil Works For Karmyogi Bhavan In Sector-10A, At Gandhinagar.-1 Demolition of Brick work and stone masonry including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift.(ii) In Cement Mortar. 2 Providing & Fixing Sandwich type Kitchen Platform of 600 wide using Top 18mm thick granite of approved shade and sample and bottom 25mm thick single side Polished kota stone with 25 mm thick screed of cement mortar 1:3 With granite Facia Patti. and vertical End granite supports. The stone shall be fixed by chassing in to the wall surface and supported vertically with 25mm thick sandwich kota stone support including SS Sink of size 610 x 460 mm waste brass coupling, stainless steel extension nipple, flexible PVC outlay pipe,Hindware Sink cock with Casted Swinging Spout F100034 etc complete as suggested by Engineer -incharge. 3 Providing Carcass below Plateform having depth 550mm X Ht 750mm made from 18mm post laminated Plywood with PUR Glue, Resting on 100mm PVC levelors and 100mm snap fitted PVC skirting with Rubber gasket in bottom as per requirements and dimensions. as suggested by Engineer -in-charge. 4 Providing modular partition full height with whole frame structure of powder coated Aluminium extruded alloy sections with Twin layers of Glass glued with Aluminum glass section by 3M taps.Horizontal venetian blinds with swivelling mechanism are provided between two glasses with out side control as specifed in specification sheet. as suggested by Engineer -in-charge. 5 ccoustic Panelling / Staging with V board with metal framing: The framework shall be prepared from RHS metal section of size 50 mm x 25 mm x 2.0 mm fixed approximately at spacing not more than @ 450 mm c/c both ways. At the joint of cladding material, two back to back metal members of size as specified above shall be provided with rockwool filling inside and shall be supported by filling required size wedges / washers / MS wall connectors or packings of washers to ensure right angles and plumb level. The framing shall be fixed with the walls and/or floors (for floors, the framing shall be fixed to the concrete surface and not flooring mortar) by nylon grip screws of approved make and sample. The frame work shall be measured in sqm of elevation and/or floor area. The face of the panelling shall be finished with 18 mm thick Fiber cement board (V-board). Rates shall be inclusive of cost of making cut outs / openings for electrical fixtures, tube lights etc. & providing additional sections for strengthening the openings / cut-outs, as per drawing or instruction of EIC. Area of cut-outs shall not be deducted and no extra payment shall be considered for additional sections provided. 6 Providing and fixing Passage Door with glass shutters are made from 12 mm thick toughened glass fixed on Floor spring with S.S. Patches satin finished of Ozone or equivivelent brand including satin finished SS handles for glass door with bottom lock including all labour and material and hardware as per detailed drawing and as directed by Engineer Incharge. 7 Providing and applying plastic emultion paint of Asian paint/ICI Dulex /Berger of Royal luxury Emulsion of Asian paints in minimum 2coats including scrapping, opeining of existing cracks, filling up of v cracks with epoxy expandable putty to required depths making good weakplastered unplastered surfaces with cement plaster where everrequired. Item t o include plaster of paris , primer putty & makinggood existing surface to receive new paint including cleaning on completion of painting work etc. complete in all respects. as suggested by Engineer -in-charge. 8 Providing and fixing roller blind made out of decorative fabric made up of 25% 50% polyster, 50% to 75% PVC. It should have specific low emissivity treatment and lead free with Greenguard certification. It should have 3% - 5% openness, including antimicrobial additive preferably Microban. The fabric should be 0.76mm 0.99mm thick, mesh weight should be 16.40 - 16.70 (oz/yd2), frame retardant, Jaquard weave with 10 years of warranty against any distortion in fabric due to any reason. UV blockage should be approx. 95%. Roller Blind tube is made of aluminium with a dia of 38mm anodized, bottom rail is powder coated & mechanism of plastic with chain and metal bracket, sturdy fixing arrangement as per direction Engineer in charge. 9 Providing and fixing wooden Platform for Dias made from 19mm water proofing plywood and batten patti of 25mm X 12.5mm and covered by PVC flooring carpet made by LG company having 1.5mm thickness including citting stitching and jointing with necessary solution and hardware, labour etc complete. as suggested by Engineer -in-charge. 10 Providing and fixing eco-friendly light weight calcium silicate False ceiling tiles having Tegular edge & 15 mm Thick Densified edges on the Tile Periphery for Extra Strength The Light weight calcium silicate ceiling tiles shall have, light reflection 85% non-combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity0.043° w/m KC.for the best thermal Insulation . The Light weight calcium Silicate tile shall be of approved texture Fine fissured/ Spintone/Cosmos having NRC value of 0.5 & Globe having NRC value of 0.75 NRC equivalent of size 595 X 595 mm to be laid on true horizontal level suspended inter locking metal grid of hot dipped galvanized steel sections (galvanizing @120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and size 24X38mm made from 0.30 mm thick (minimum) sheet, 1200mm centre to centre, and cross ‘T’ size 24X28mm made out of 0.33mm (Minimum) sheet spaced 1200mm along spaced between main ‘T’ at 600mm centre to centre to form agrid of 1200X600mm and secondary cross ’T’ length 600mm and size 24x28mm made of 0.30 mm thick (Minimum) sheet to be interlocked middle of the 1200X600mm panel to form grid of size 600X600mm resting on periphery walls/partitions on a perimeter wall angle pre-coated steel of size (24X24X3000mm made 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm centre to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick Densified edges light weight calcium silicate ceiling tiles of approved texture (Fine Fissured/Cosmos/Spintone) in the grid including, cutting /making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required, Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25X35X1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm G.I. adjustable rods with galvanized steel level clips of size 85X30X0.8mm, spaced 1200mm centre to centre long main ‘T’ bottom exposed with 24mm of all T-sections shall be prepainted with polyester baked paint, for all heights, as per specifications, drawings and as directed by engineer-in-charge.Note:- Only calcium silicate false ceiling area will be measured from wall wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm. The calcium silicate ceiling tiles shall have NRC. Value of 0.50 (Minimum) for Fine fissured/Spintone/Cosmos and 0.75 NRC for Globe, light reflection 85% non-combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity. 0.043° w/ KC.for the best thermal Insulation 11 CAFETERIA CHAIR : The Seat and Back should be made up of injection moulded indoor grade PolyPropylene compound SEAT SIZE : 52.5 cm. (W) x 53.2 cm. (D) BACK SIZE 51.6 cm. (W) x 40.5 cm. (H) The powder coated ( DFT 50±10 microns ) welded tubular frame should be made from 0 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm and 3.5 0.03 cm x 1.5 ± 0.03 cm x 0.16 ± 0.0128 cm MSERW tube. The shoes should be made of indoor grade PolyPropylene compound and snap fitted with tubular frame. Overall Dimensions of Chair Seat Height - 45.0 cm. Height - 84.5cm. Width-52.5 cm and Depth-55.8 cm. Approve Make ;Steel Case.Godrej,Kompress.The product should be Green Guard certified from U/L with VOC values. Product specific certificate to be submitted alongwith the tender. Approve Make ;Steel Case.Godrej,Kompress. as suggested by Engineer -in-charge. 12 CAFETRIA TABLE : 1200 x 600 x 750mm Table top should be made of 25min thk. MDF OSR board (Bottom side in white color) as per IS:12406 PU coated on top side. Legs should be made by welding the combination of MS ERW round Tube 063.5 x 2mm THK as per IS: 7138, flanges made CRCA sheet of 1.6mm thk. and 1.2mm thk. as per IS 513 and inside plates made of HR 5mm thk. sheet as per IS:2062. The Assembly will be epoxy polyester powder coated of minimum thickness 45 microns. The Table top will fold upside at offset center pivot provided on support bracket which should be Aluminum alloy (ADC12) pressure die cast part coated with epoxy polyester powder coating of minimum thickness of 45 microns. Table top connected with spring loaded mechanism with pull handle made of MS ERW 016x1 2mm thk with an insert tube of 012.7x1.6mm thk tube as per IS:7138 coated with epoxy polyester powder coated of minimum 45 micron thickness to operate table top. Legs should be provided with casters of 065mm lockable type for ease of movement and can be locked when required at any position.The product should be Green Guard certified from U/L with VOC values. Product specific certificate to be submitted alongwith the tender, Approve Make ;Steel Case.Godrej,Kompress. 13 CAFETRIA TABLE : 1500 x 750 x 750mm Table top should be made of 25min thk. MDF OSR board (Bottom side in white color) as per IS:12406 PU coated on top side. Legs should be made by welding the combination of MS ERW round Tube 063.5 x 2mm THK as per IS: 7138, flanges made CRCA sheet of 1.6mm thk. and 1.2mm thk. as per IS 513 and inside plates made of HR 5mm thk. sheet as per IS:2062. The Assembly will be epoxy polyester powder coated of minimum thickness 45 microns. The Table top will fold upside at offset center pivot provided on support bracket which should be Aluminum alloy (ADC12) pressure die cast part coated with epoxy polyester powder coating of minimum thickness of 45 microns. Table top connected with spring loaded mechanism with pull handle made of MS ERW 016x1 2mm thk with an insert tube of 012.7x1.6mm thk tube as per IS:7138 coated with epoxy polyester powder coated of minimum 45 micron thickness to operate table top. Legs should be provided with casters of 065mm lockable type for ease of movement and can be locked when required at any position.The product should be Green Guard certified from U/L with VOC values. Product specific certificate to be submitted alongwith the tender, Approve Make ;Steel Case.Godrej,Kompress. as suggested by Engineer -in-charge. 14 Committee room table (29 Seater) Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above. Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns. Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted pull out audio,video cables onto worktop and connect devices charger to power socket below worktop.The product should be Green Guard certified from U/L with VOC values. Product specific certificate to be submitted alongwith the tender. Approve Make ;Steel Case.Godrej,Kompress 15 Committee room table (15 Seater) Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above. Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns. Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted pull out audio,video cables onto worktop and connect devices charger to power socket below worktop.The product should be Green Guard certified from U/L with VOC values. Product specific certificate to be submitted alongwith the tender. Approve Make ;Steel Case.Godrej,Kompress 1 2 16 Committee room table (03 Seater) Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above. Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns. Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop.The product should be Green Guard certified from U/L with VOC values. Product specific certificate to be submitted alongwith the tender. Approve Make ;Steel Case.Godrej,Kompress. as suggested by Engineer -in-charge. 17 Committee room table (02 Seater) Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above. Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns. Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop.The product should be Green Guard certified from U/L with VOC values. Product specific certificate to be submitted alongwith the tender. Approve Make ;Steel Case.Godrej,Kompress. as suggested by Engineer -in-charge. 18 committee Chairs 1) SEAT / BACK: The seat sub-assembly is made up of 1.240. 1am thk Plywood measured as per QA method described in OCP-OLTA-P14-18 upholstered with moudded foam and polyester fabric and covered with an infection-moulded polypropylene outer cover. The seat can lip~up when not in use and this feature can be used while stacking the chairs horizontally. The back sut-assembly is made up of Infection-moulded polypropylene inner upholstered with mouided foam and polyester fabric and covered with an infection-moulded polypropylene outer cover. The contoured back with width extension at the botiom area is designed to give comfort to lower back. The back flending features allows the back to tit by 9°12° to ald the user in adopting a comfortable redining posture. Both these sub-assembles are fleed to the tubular structure.*BACK SIZE:/ 45.2cm (W) X 44.6cm (H)*SEAT SIZE: 147.0cm (M) X L2.0cm (D) 2) TUBULAR FRAME STRUCTURE® The pouder-coated 4 log structuro is mado of 22 40 oscm da x 0.25 10.02cm thk M.S. E.R,W. Tube front and rear leg welded along with connecting tube made of 1.9 10.02cm dia x 0.2 0.016cn thk M.S. E.R.W. Tube to form the tubular frame assembly. The legs are provided with injection-moulded adopter bush in black Nylon and brake-loaded castors enabling easy maneuvering while not in use and stable sitting while in use. The chairs can be stacked horizontally when not in use. : 3) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 70 +8 kg/m and Hardness load for Seat 16 1 2 kg and Hardness load for back 12 + 2 4) ARMRESTS (for SCINXD/SCINIX only): The arrest structure is made up of 2 2 40.03cm dia x 0 25 10.02cm thk M.S. E.R.W. Tube welded to the Tubular Frame structure and having a scratchresistant ABS Arm top. 1. FULL DESKLET (for SCINXD only): The Full Desket assembly is Flip-up type and is made up of extension tube of 1.9 10.02cm dia × 0.2 10.016cm thk M.S. E_R.W. Tube and a support tube on L.H. side of 1.6 0.02cm dia x 0.2 10.016cm thk M.S. E. R.W. Tube on which an scratch resistant ABS desklet top is fixed and covered on bottom side with a bottom cover. 2. BRAKE-LOADED CASTORS (for SCINXD): The brake-loaded castors are assembled to the chair legs, to give a free movement for maneuvering the chair when not in use and it will brake the movement when load is applied (while in use) to give a stable feel. The twin wheel castors are injection molded in black Polypropylene. 3. TWIN WHEEL CASTORS (for SCINIX / SCINXOX): The twin wheel castors are injection moulded in 4. Black Nylon +30%GF. The product should be Green Guard certified from U/L with VOC values. Product specific certificate to be submitted alongwith the tender. Approve Make ;Steel Case.Godrej,Kompress. as suggested by Engineer -in-charge. 19 Conference Chair 1. SEAT/BACK ASSEMBLY: The seat is made up of 1.2 ‡ 0. 1cm thk. hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18. The Back is made up of injection moulded glass filled nylon & upholstered using Net fabric with high tenacity yarn. SEAT SIZE(Larger Seat Depth) (PULSAL, PULSTL) : 47.0 cm. (W) × 51.5 cm. (D) SEAT SIZE(Standard Seat Depth PULSAX, PULSTX) : 47.0 cm. (W) × 49.5 cm. (D) BACK SIZE (PULSAX,PULSAL, PULSTX, PULSTL): 45.0 cm. (W) x 65.3 cm. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m° and hardness 16 ‡ 2 kgf as per IS:7888 for 25% compression. ARMRESTS (ADJUSTABLEPULSAX, PULSAL): The armrests have an Up-Down adjustment 8.5 * 0.5cm which is provided in armrest structure. Armrest Top has an integrated layer of Thermoplastic Elastomer (TE). 1. LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 + 0.5 cm in height. 2. NECKREST ( PULSNR ): The Neckrest assembly consist of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. Neckrest is fixed to Back Assembly through Neckrest connector. Neckrest assembly has height adjustment of 4.2 ‡ 0.5 cm and rotation adjustment of overall 76° 2°. The complete neckrest assembly is retro fit to the main chair. 3. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ‡ 0.3 cm. 4. PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 066.1 ‡ 0.5 cm. (76.1 ÷ 1.0 cm. with castors). 5. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Nylon.The product should be Green Guard certified from U/L with VOC values. Product specific certificate be submitted alongwith the tender Approve Make ;Steel Case.Godrej,Kompress. as suggested by Engineer -in-charge. 20 Waiting Room Sofa 3 seater Providing, supplying and installation of three seater sofa. 1)SEAT FOAM : The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. 2)BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. 3)UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. 4)LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width (W): 206.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.he product should be Green Guard certified from U/L with VOC values. Product specific certificate to be submitted alongwith the tender.Approve Make ;Steel Case.Godrej,Kompress. as suggested by Engineer -in-charge. 21 Waiting Room Sofa 2 seater Providing, supplying and installation of two seater sofa. 1)SEAT FOAM : The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. 2)BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. 3)UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. 4)LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width (W): 206.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.he product should be Green Guard certified from U/L with VOC values. Product specific certificate to be submitted alongwith the tender. Approve Make ;Steel Case.Godrej,Kompress. as suggested by Engineer -in-charge. 22 Wating Room Center table Providing, supplying and installation of centre table. 1)PISA SIDE TABLE & CENTER TABLE GLASS: It is 10 ±0.3 mm thick black tinted Toughened glass UV glued with bushes made in SS 202 grade for focing with understructure. 2)PISA SIDE & CENTER TABLE UNDERSTRUCTURE: It is a welded Assembly made in SS202 grade Dia. 12±0.04 as per IS:1762. Width of table= 112.0 cm, Depth=60.0 cm, height=34.9 cm. he product should be Green Guard certified from U/L with VOC values. Product specific certificate to be submitted alongwith the tender. Approve Make ;Steel Case.Godrej,Kompress. as suggested by Engineer -in-charge. 23 Wating room Side Table Providing, supplying and installation of side table. 1) PISA SIDE TABLE & CENTER TABLE GLASS: It is 10 ±0.3 mm thick black tinted Toughened glass UV glued with bushes made in SS 202 grade for focing with understructure. 2)PISA SIDE & CENTER TABLE UNDERSTRUCTURE: It is a welded Assembly made in SS202 grade Dia. 12±0.04 as per IS:1762. Width of table= 60.0 cm, Depth=60.0 cm, height=34.9 cm.he product should be Green Guard certified from U/L with VOC values. Product specific certificate to be submitted alongwith the tender.Approve Make ;Steel Case.Godrej,Kompress. as suggested by Engineer -in-charge. 24 Archieves Storages : Providing Storage unit Single Drive Cover Unit 3 Bay/ 4 bay (U/C + Fittings + Cover) . The Construction shall be rigid knock down made out of 0.8 thick CRCA steel conforming to IS : 513 . Each body shall have a main unit plus add on units (1,2,3) . Finish shall be Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be made from CRCA steel 0.8 mm thick IS :513 .Uniformly distributed load capacity of 100 Kg . Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick conforming to IS : 2062. The Movements shall be Drive Type configuration : In case of D3 & D4 movement of units is achieved mechanically through a PU Drive Wheel and Sprocket -Chain- Tensioner arrangement mounted rigidly onto body size. For D3 each movable undercarriage shall be provided with 3 rollers on the shaft for driving ,3 antifriction ball bearing for rolling.LD understructure has 2 nos. of anti-tilt bearing assembly.The roller assembly comprises of a die-cast step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and is fitted onto the MS shaft using a feather key. The two ball bearings are then fastened on either side of the step wheel using circlips. This entire roller assembly is then snapfitted into a wheel housing. The wheel housing is fixed in the U channel of the understructure using machine screws. This wheel-housing is made of engineering plastic material made by injection-molding process. The entire roller assembly is designed to withstand the maximum loads of the body. Fittings shall be centralized locking arrangement through locking stiffener mounted onto back of single last unit so that it gets locked on channels when all the units are brought together. The Recess handle lock is placed at suitable height .The ‘sprocket-chain’ arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x 398mm x 87mm and is fixed onto the side of the body. The PU handwheel is rigidly fixed at suitable height on side of the body & projects out of cover by another 99.0 mm. Fixed unit (SD) does not have the Drive Unit Cover. When the last unit is twin movable, hinged doors as accessories are provided for the end bodies, so in this case locking stiffener is mounted onto drive unit cover; and with tile fascia option, it will be mounted in the recess of vertical trim. Each Drive Type units shall have Locking Knob near the drive wheel for manual locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. End stoppers shall be provided to prevent derailment.The nuts & bolts are galvanized / blackodized / Zn Plated. Also total no. of loading levels per understructure shall be 15 for SD3 and 20 for SD4. Label holder - It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. The product should be Green Guard certified from U/L with VOC values. Product specific certificate to be submitted alongwith the tender. Approved Make : Steelcase, Godrej, Kompress. as suggested by Engineer -in-charge. 25 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length , in below type of pipe erected with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed. (f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat. III 26 Removing and re erecting light/bell/ fan modular points as per site requirement (i) partial PVC pipe and drops in oval conduit / PVC casing capping erected concealed in wall/ceiling complete Removing charges half of reerecting charges (39+78=117) 27 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected with 6A Modular type switch and hum free EME step type electronic fan regulator mounted and accessories with earth continuity of following type erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed. (f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete 28A Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in below type of pipe erected complete with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories. [I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db board (f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat III [II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db board. 28B (f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete 29 Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate modules erected on / in wall / ceiling with following type accessories Cat. III 30A Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (a) 20 mm 30B (b) 25 mm 31 Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (2) 20mm 32A Replacing old & u/s by Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size (e) in existing pipe (a) 2 wire 1.5 sq. mm 32B (b) 2 wire 2.5 sq. mm 33 Providing & erecting Switch board for Computer or electric apparatus consisting of following modular type accessories mounted with PVC / Metallic concealed/open box with single mounting base frame covered with textured/metallic /white front plate,modules erected with necessary connections as directed 1 no. 6A/16A universal plug-switch combined. 3 nos. 6A Switch 3 nos. 6A 5 pin Plug [B] For Modular Type Accessories Cat. III 34 Supplying & erecting Approved make call bell indicator with buzzing sound and Red light indicating lamp with Red light button to attend the call suitable for 240 v 50 c/s supply to be erected. 35A Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium pressure die cast powder coated and high U.V. & corrosion resistance with diffuser housed in aluminium casted body with company mark/name 160V to 270V,Power Factor more than 0.95, THD < 15 %, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 % ( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.) (A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded mounting clips complete.IP20 (iii) 16-20 watts, Surge-2 KVCat-lll 35B (B) LED Panel Light with provision for Plane front frame with translucent cover fixed to housing complete.IP20 (vi) 36 watts, 24 x 24, Surge- 2KV Cat-lll 36 Providing and erecting Approved make Ceiling fan with double ball bearing ISI mark with condenser A.C. 23OV.50 c/s.1200 mm. sweep complete, canopy erected on existing hook or clamp with earthing. [Make shall be approved by Engineer in charge] 37 Supplying and erecting approved make oscillating type bracket fan A.C. 23OV. 50cy/s 400/450 mm sweep wall mounted with height adjustment and rotary tilting device complete with guard, flexible Core plug top complete erected with lead wires as directed. Cat.II 38 Supplying & erecting approved make LAN cable of following size in existing pipe as per direction [C] CAT - 6 39 SITC of 3LCD Lamp based projector having wxga (1280x800) or better resolution with minimum white brightness of 3800 lumens and color brightness of 3800 lumens. The projector should have minimum 1HDMI,1VGA input. Having contrast ratio of 15000:1 or more. the projector should have auto vertical key stone correction of +/- 30 degree and Manual Horizontal of +/-30 degree. the projector should have optical lens, throw ratio 1.30-1.56:1. Zoom Factor of 1.2. Lens focus Manual having focal length 16.9mm to 20.28mm. projector should have features like AV mute slide, quick corner and split function and should support wireless functionality with inbuilt wifi or wifi dongle. [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 40 SITC of universal Projector mounting kit, with necessary grouting, fasteners etc. with adjustable height and suitable for all types of projectors. [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 41 SITC of 84 inch Self Lock MW (6 x 4) Instalock Slow Retraction Screen, Aspect Ratio-4:3 [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 42 SITC of Participant device long mic, black[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 43 SITC of Chairperson device long mic, black [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 44 Providing and erecting cordless microphone with UHF Diversity handheld wireless microphone/caller wireless complete with receiver and transmitter unit,Cardiod ,polar pattern,dynamic microphone,LCD display for battery and frequency status and information ,32 preset channels,with compatible groups of 8 channels,14 hrs.battery life,frequency response 80Hz to 18KHz.,RF sensitivity <1.0 Uv,image rejection > 55 dB,dynamic range >95 dB and receiver having 32 channels,S/N ratio>100 dBA,Dynamic range>95 dB,distortion<1% [[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 45 Replacing old & u/s by SITC of Control unit [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 46 SITC of EXTENSION CABLE ASSEMBLY - 2MTRS [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 47 SITC of EXTENSION CABLE ASSEMBLY - 5 MTRS [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 48 SITC of EXTENSION CABLE ASSEMBLY - 10 MTRS [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 49 SITC of PLENA 360W ALL-IN-ONE AMPLIFIER [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 50 SITC of Cabinet loudspeaker, 30W, black High-fidelity music and speech reproduction Selectable 8 ohm, 70 V and 100 V inputs Compact yet robust ABS enclosure Supplied with adjustable mounting bracket Complies with international installation and safety regulations [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 51 SITC of CAT6 UTP 23AWG Solid: Per Meter [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 52 SITC of shilded 2 core 20 AWG Audio Cable 53 SITC of shilded 2 core 2.5 sqmm loudspeaker cable 54 Replacing old & u/s by Supply, Installation Testing & Commissioning of 6 ft HDMI Interface Cable should be 6ft male to male High speed category 2 HDMI cable: should be 24K gold -plated 19 pin Type A connector; should have High -Flex CL-3 rated jacket; should support 4K60 4:4:4 video; should support 18Gbps bandwidth: should be RoHS comliant (Aporoved Make: Creston/Extron/Lightware) 55 Replacing old & u/s by Supply, Installation Testing & Commissioning of 20 ft HDMI Interface Cable should be 6ft male to male High speed category 2 HDMI cable: should be 24K gold -plated 19 pin Type A connector; should have High -Flex CL-3 rated jacket; should support 4K60 4:4:4 56 Sitc of Digital signal Processor (DSP) with 12 anaalog inputs and 8 analog outputs, and includes acoustic echo cancellation (AEC) technology on all12 inputs.it also includes up to 8 channels of configurable USB audio, Frequency Response: 20Hz to 20k Hz,+4dBu output: +0.25 dB/-0.5 dB, THD +N (22 Hz to 22kHz): 0dB gain, +4 dBu input;<0.006% 54dBu gain, -50dBu input:< 0.040% Dynamic Range(in presence of Signal) 22Hz to 22kHz, 0dB gain:> 108 dB; Input Impedence(balnced) :8k ; output impedance(balanced):207; Crosstalk, channelto channel, 1kHz: 0dB gain,+4dBu input;< -85dB 54dB gain,-50dbu input :<-75dB; 57 Supply, Installation, Testing and Comissioning of USB PTZ Full HD 1080p@60fps Video Conferencing PTZ Camera, 1/2.8 CMOS 2 MP sensor, 59.5 degree FOV, 20X Optical Zoom & 12 X Digital zoom , PAN with± 170 degree, Tilt(+) 90degree and(-)30degree ,H.264/H.265 Video compression, Auto white balance,Auto focus,Support backlight compensation, Auto gain control,Supports PAN/NTSC signal system ,preset No-256 Multiple picture adjustment,Built in Streaming support & Dual streaming,compatible with ONVF,RTSP,RTMP,HTTP,TCP,UDP rpotocols, Audio compression AAC,RS-232 control interface,Presenter & preset tracking support,USB 2.0,HDMI,SDI,RJ-45,Audio IN interfaces & NDI support,Camera control Management Software,BIS,CE, FCC, RoHS certified. 58A Providing and erecting Inverter based approved make Cassette type split air-conditioning unit consisting of condensing unit with fan motor, hermetically sealed scroll/rotary compressor with accessories etc. duly connected separately erected evaporating unit and blower motor with its accessories by Eco friendly Green gas charging & Internal copper wiring & Remote control ( 3 star and above of current year) with necessary core cutting. (D) for 4 ton capacity- 3Phase 58B (C) for 3 ton capacity- 3Phase 59 Supplying and erecting insulated pair of soft copper tubing open or concealed including power and control cable,necessary PVC drain pipes for Split AC machine up to 4 TR capacity 60 Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation. (E) 19 mm dia. 61 Providng and erecting Approved make energy meter 3 phase 4 wire unbalanced load rating, 10A to 60 Amp. based on ASIC(Application specific Integral Circuits) digital technology with accuracy Class - 1 , temper proof, free from effect of external magnetic field with 3 phase indication, earth & impulse indication, 6 digit electro mechanical impulse counter, suitable work on 120 V to 300V per phase 45-55 HZ, housed in robust enclosure with erection as directed.Cat. III 62 providng and erecting Suitable set of CTS for 100A Energy Meter 63 Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be erected as directed of following size. (A)7 core 1.5 Sq. mm
