Tender For Day To Day Complaints Comprehensive Maintenance And Periodical Services And Repair Maintenance Of Internal Wiring Ceiling Fan Ac Etc And Day To Day Complaints Of Internal Electrification At 213 Transit Camp Under Ge Nagrota- 1 S & F in repairs, Fancy Type CP long body bib tap cast copper alloy with crutch or butterfly handle 15mm bore screwed down screwed for iron pipe (ISI marked) or equivalent as approved complete all as specified and directed. 2 S & F in repairs,Fancy type Bib tap, cast copper alloy with crutch or butterfly handle 15mm bore screwed down, screwed for iron pipe or for brass ferrule (ISI marked) or equivalent as approved complete all as specified and directed. 3 S & F in repairs,Bib tap15 mm standard of PTMT any colour screwed for iron pipe (Minimum weight 15mm-90 gms)complete all as specified and directed. 4 S&F in repairs, CP brass wall/WHB mixer for cold and hot water screwed down 15mm bore complete all as specified and directed. 5 S/F in repairs15 mm dia wall Bend mixer brass chromium plated fixed to existing pipe/connections cluding telephonic hand shower and all necessary fittings complete all as specified and directed. 6 Supply and fixing in repairs CP brass jet spray with flexible pipe not less than 90 cm long fixed to EWC suitable for 15mm bore complete all as specified and directed at site 7 S & F in repairs,15 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimumweight15mm-142gms complete all as specified and directed. 8 S & F in repairs,20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 2 0 m m - 2 1 0 g m s. complete all as specified and directed. 9 S & F Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats.(Minimum weight 190gms)complete all as specified and directed. 10 Material and labour for replacement of syphonic aseembly of PVC low level cisterncomplete all as specified and directed. 11 S & F in Rotational moulded polyethylene (three layer) water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position of capacity 500 litres all as specified in SSR Part-I. complete all as specified and directed. 12 All as per item No -11 here in before but 1000 litres complete all as specified and directed.. 13 S/F in repairs of glass shelf assembly corner/Straight consisting of 5.5 mm thick sheets glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. 14 S/F in repairs of Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms)complete all as specified and directed. 15 S & F in repairs,15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed. 16 S & F in repairs,15mm bore CP brass angle stop valve/cock cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. 17 S & F in repairs,15mm bore CP brass stop cock fancy type, chromium plated with iron long shank and cup Concealed type complete all as specified and as directed. 18 S & F in repairs, Waste coupling PTMT chromium plated(Half or full tread) for wash hand basin with long screwed shanks and fly nuts fixed in repair 40mm-60gms complete all as specified and as directed. 19 S & F in repairs,32 mm bore PVC waste pipe flexible including PVC waste coupling with minimum length 800mm, complete all as specified and directed. 20 S & F in repairs, PVC valve less symphonic action type, flushing cistern, low level, white of capacity 10 ltrs with inlet , ball valve, float and and fixing arrangement ccomplete all as specified and as directed. 21 S & F in repairs,Wash basins, vitreous china white (flat back type) of size 550x400 mm , excluding taps, waste chain and plug and porcelain stopper but including brackets and 32mm dia waste fittings brass chromium plated with long screwed shanks and fly nuts, 32mm x 600mm long PVC waste pipe complete flange end bedded in red lead cement and other end fixed as in repair complete all as specified and directed. 22 S & F in repairs,Wash basins, vitreous china white (Angle back type) of size 400x400 mm , excluding taps, waste chain and plug and porcelain stopper but including brackets and 32mm dia waste fittings brass chromium plated with long screwed shanks and fly nuts, 32mm x 600mm long PVC waste pipe complete flange end bedded in red lead cement and other end fixed as in repair complete all as specified and directed. 23 S & F in repairs,Wash basins, vitreous china white of oval shape counter top, excluding taps, waste chain and plug and porcelain stopper but including brackets and 32mm dia waste fittings brass chromium plated with long screwed shanks and fly nuts, 32mm x 600mm long PVC waste pipe complete flange end bedded in red lead cement and other end fixed as in repair complete all as specified and directed. 24 S & F in Vitreous china squatting pan “Orrisa” pattern of size 580mm “White” with P or S Trapfront or back inlet and foot rests, any pattern (excluding flushing cistern and flush pipe), connection to trap andto flushing pipe anti- syphonage pipe etc complete making good complete all as specified and directed. 25 S & F Vitreous china wash down closet pan (Pedestal pattern) white with ‘S’&Ptrap plastic seat cover white including connection to out going pipe & to flushing pipe, anti syphonage pipeetc complete all as specified and directed by Engineer-in-charge (including making good to floor and fixing in repairs) 26 S & F Stainless steel sink with drainage board made out of 1mm thick sheet for kitchen or laboratory with plug, washer, waste pipe etc including cast iron brackets, connecting union over all size 915mm X 460mm with bowl size 410mm X 330mm X 160mm complete all as specified and directed. 27 S & F 600mm x 450mm size beveled edge mirror of 6mm thick selected quality mounted on 6mm thick plywood with chromium plated screws with washer complete all as specified and directed. 28 S & F in repairs,Plastic water closet seat cover, white closed pattern with flat bottom and cover and Brass chromium plated hinging device complete all as specified and directed. 29 S & F in repairs,125 mm dia Fancy type shower rose with arm swivel type fixed to 15mm dia pipe all as spd. 30 Taking down steel tubing and connections includingremoving from siteof 15mm borepipe complete all as specified and directed. 31 All as above item No 30but 20mm bore complete all as specified and directed. 32 S&F 15mm bore steel water tubing medium grade , galvanized ISI marked with all fittings fixed to wall & ceiling or laid in floors complete all as specified and directed by Engineer-in-charge. 33 All as per item No 32 bove but 20mm bore complete all as specified and directed. 34 S & F Flush pipe (Long/Short Bend) of polyethylene of low or high density of PVC, 32mm dia for low level cistern fixed in repair complete all as specified and directed. 35 M & L 5.5mm thick selected quality tinted sheet glass and glazing in square fixed with PVC /Neoprene gasket in aluminium frame work complete all as specified and directed. 36 M & L for 12 mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice laminations fixed in wooden/aluminium frame work complete all as specified and directed. 37 S & F in repairs,125mm long safety type aluminium anodized hasp and staples complete all as specified and directed. 38 S & F in repairs,Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminum alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed. 39 S & F Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutter of 851 to 1000mm in width & of weight between 61 to 81 kg aluminium extruded section body complete all as specified and directed. 40 M & L for 12mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both facescomplete all as specified and directed. 41 M & L for 19/20mm thick block board Grade I quality exterior grade, decorative type with decorative face veneers on one face for cupboard etc complete all as specified and directed. 42 M & L for 9mm thick plywood grade BWR type BB No of ply 5 complete all as specified and directed. 43 M & L for Second class hard wood plainfillets, square, rectangular or triangular in section, and secured with nails or screws, clean sawn and sectional area exc 13 Sq cm and not exc 25 Sq cm complete all as specified and directed. 44 Material and labour for4 mm thick sheet glass ordinary quality and glazing with oil putty in squares n.exc. 0.50 sqm in each pane complete all as specified and directed. 45 M & L for 4mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane including hacking out old glass panes complete all as specified and directed. 46 M & L for 4mm thick figured glass, pin head type and glazing with oil putty in square n.exc 0.5 Sqm each pane 47 S & F in repairs, 75 mm long Butt hinges, (ISI marked) medium weight cold rolled mild steel fixed with screws or welding fixed in repair including taking down shutter and refixing in same position 48 S & F in repairs, All as per item No 47 here in before but 100 mm long complete all as specified and directed. 49 S & F in repairs, Mild steel Helical door springs including roller plate complete of 150mm long complete all as specified and directed. 50 S & F in repairs, Floor door stopper 150MM of aluminium alloy body and tongue anodized with double rubber fixed in repair complete all as specified and directed. 51 M & L for, Galvanised mild steel wire cloth 0.457mm nominal dia of wire and average width of aperture 1.18mm and fixed with wooden/MS beadscomplete all as specified and directed. 52 Demolition of Concrete (Unreinforced) of any description and in anypositionnot otherwise specifically provided for complete all as specified and directed. 53 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as spd and directed 54 M & L for25 mm thick PCC 1:2:4 type B-0 (12.5 mm graded crushed stone aggregate) as a sub base toreceive topping layer finished even and roughcomplete all as specified and directed. 55 Demolition of stone slabs of any description or thickness inkitchen platform, floors,aprons laid, bedded,pointing in any mortar etc complete all as specified and directed. 56 M&L of Machine cut kota stone flooring 18-20 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing ( mirror finish) (Each stone not less than 55 cms x 55 cms) over 15mm thick screed bed in CM ( 1:4) as in floor finished roughincluding roughening of existing surfaces by pick axicess and applying a coat of cement slurry @ 03 Kg/Sqm of surface. complete all as specified and directed. 57 M & L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over 15mm thick screed bed in CM ( 1:4) complete all as spd and directed 58 S&FNon-skid ceramic colouredtiles 7 to 8mm thick area of each tile exceeding 0.11sqm but n exc 0.18 Sqmin floors etc set and jointed inneat cement slurry and pointed in white or coloured cement to match over 15 mm thickscreed bed or beddding layer of CM 1:4 including complete all as spd and directed. 59 M & L Glazed ceramic tiles coloured (Premier quality)in vertical surface of size 300mm x450 mm x 7mm thick jointing in neat cement slurry and pointing in colour cement to match includingincl 10mm thick screed bed/bedding layers in cm 1:4complete all as specified and directed. 60 M & L for Virified Ceramic tiles 10 mmthick (square/ rectangular) light shade polished, area of each tiles not exceeding 0.36 sqm,as in patches in floors, set and jointed with cement slurry and pointed with white or coloured cement to match withtiles over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed. 61 M & L for 25 mm diaaluminium anodiseddreproy rod with hanging and side brackets powder coated textured finishand wall thickness 1mmcomplete designed and patterned as approved complete all as specified and directed. 62 M & L for 20 mm diaHarrison rails, mild steel, chromium plated with fixing bracketsstops, rollers etc.steeldreproy rod with hanging and side bracketswall thickness 1mmcomplete all as specified and directed. 63 Supply and fixing 125mm dia steel grating fixed in position complete all as specified and directed. 64 S & F in repairs, PVC cover/lid for PVC over head water tank suitable for capacity of above 500 ltrs and upto1000 ltrs capacitycomplete all as specified and directed. 65 Supply and fix for PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified and as directed. 66 Supply and fix for factory made PVC door shutter 30mm thick (style) consisting of frame made out MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheets of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and as directed. 67 M & L for Attending complaint for repair to easing of any type of Doors/window/cup board shutters incl Alu doors by tightening of hinges/handles/aldrop bolt/tower bolt/knobs, hasp and staple etc of any size/ any number of panels for easy closing/opening or changing the position of hinges, adjustments of tower bolts, sliding bolts, replacement of looking mirror, curtain rod etc complete including replacement of minimum defective item if required, complete all as specified and directed. 68 M & L for Petty repair to existing steel window/rolling shutters, pressed steel frame rat tails spring, steel almirah, mortise lock fitted in steel almirah and fixing wire mesh on steel windows by welding in situation and in any floor and including hinges 100mm medium weight to chowkhats after taking down door/window shutter and refixing in position and making functional (welding rod welding machine, small fittings such as windows handle, hinges etc will be provided by the contractor removing the steel window shutters from the frame and re-fixing after making serviceable complete all as specified and directed. 69 M & L for Attending complaints related to plumber/ water supply and obtaining completion from user, this includes minor repair of taps by replacement of washer/jumpers, tightening of taps, tightening of check nuts of PVC connection and making water supply functional in case of blockage, redressing of GI pipe joints if any leakage is found, repair of unfunctional PVC flushing cistern, repair/ replacement of face mohra etc including materials like GI fittings of reqd size M.Seal, safeda, sootar and washers etc, (Replacement of taps, PVC connections/ face mohras of any description & any other material shall be paid separately as supply only.) 70 Demolition of brick work or stone masonry, built in CM including all quoins, arches, pillars etc. but excluding ashlar facing, dressed stone work and precast concrete articles.complete all as specified and as directed. 71 M & L for Brick work with sub class B (old size) brick straight or curved on plan exc 6 mmean radius in CM 1:4 complete all as specified and as directed. 72 S & F in repairs Aluminium anodised handle extruded section and fixed of size 150mm complete all as specified and as directed. 73 S & F Aluminium anodised barrel tower bolts extruded section and fixed in repairs of size 150 mmcomplete all as specified and as directed. 74 S & F in repair Floor door stopper of aluminium alloy body and tongue anodized with double rubber. complete all as specified and as directed. 75 M & L for Preparing of Old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. 76 M & L for Preparing of New or previously painted wooden surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of primer complete all as specified and as directed. 77 Supply and fixing PVC bath room mirror cabinet fixed to wall with screw and rawl plugs, fixed as in repair complete all as specified and directed . 78 Supply and fixing 600mm x 750mm x 250mm plate rack stainless steel with steel shelves, made out of 1mm thick sheet and hanging arrangement, complete all as specified and directed. 79 Supply and fixing soap dish of cast copper alloy, chromium plated (CP), fixed as in repair complete all as specified and directed. 80 Supply and fixing Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed. 81 M & L for Repairing of old chromium plated bib taps, pillar taps, wash hand basin mixture, stop cock, angle valve, concealed stop cock and similar items by changing its brass phases and making it functional to the entire satisfaction of user and Engineer-in-Charge complete all as specified and as directed. 82 Material and labour for repairing of existing floor trap by cleaning and refixing the same in cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate of size 100mm dia complete all as specified and as directed. 83 M & L for Cleaning of blocked WC/ bath rooms/ kitchen gully traps including and upto first manhole by removing all choked waste in the pipe complete all as specified and as directed. 84 M & L for Opening of air block/blockage of Gi pipe from outlet of water tank to all internal fitting to enable to smooth flow of water from bib tap/shower/WHB piller taps/stop cock complete by air pressure/water gravity pressure etc complete all as directed and specified. 85 Taking down existing old tarfelt, bituminous compoundincluding cleaning & removing debris to a distance exc 100 m n.exc.250m. complete all as specified and as directed. 86 M&L for 10 mm rendering in CM 1:4 including water proofing compound @2% of cement over roof surfaces finished even and smooth without using extra cement complete all as specified and as directed.Note:- WPC Mesured and Paid Separately. 87 Supply only for Integral water proofing compound complete all as specified and as directed.. 88 M&L for Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces complete all as specified and as directed. 89 M&L forApplying evenly a tack coat of induatrial bitumen 85/25 grade @ 1.2 Kg/Sqm.complete all as specified and as directed. 90 M&L forOne layer of APP based polymeric membrane of approved manufacturer, 3mm thick, weight not less than 3.50 Kgs per Sqm , reinforced with non woven polyester fabric or weight not less than 150 gms per Sqm . Polymeric membrane shall be taken to a height 60 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing(Note (i) Laying of APP based polymeric membrane shall be done by torch on method or as per manufacturers instructions(ii) A Minimum overlap of 100 mmand 75 mm shouldbe made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as manufacturers instructions(iii) The make of polymeric membrane shall be IWL India Ltd chennai. Ltd or MOPLY FP of Texsa India Ltd). NOTE : S&F of APP based polimeric membrane of approved manufacturer will belaid/fixedby authorised person of the same manufacturers units asper relevent IS. 91 M & L for Applying one coat of aluminium paint on top of APP membrane. complete all as specified and as directed. 92 Dismantling cast-iron/PVC pipes including fittings taking out of trenches or walls as required dia of pipe upto 100mm. complete all as specified and as directed. 93 S&F 110mm dia PVC pipe single socketed in any length with rubber ring joints, fixed to walll and in trenches or in floors, fixed in repairs. complete all as specified and as directed. 94 S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls for 75mm bore complete all as specified and as directed.. 95 S&F PVC (SWR) Bendsany radius for 110mm bore complete all as specified and as directed.. 96 S&F PVC (SWR) Bendsany radius for 75mm bore with oval access door complete all as specified and as directed.. 97 S&F in repairs Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof for 100 mm bore complete all as specified and as directed. 98 M & L for Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, et Exc 250 and n exc 500 ltr. complete all as specified and as directed. 99 M & L for Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, et Exc 500and n exc 1000 ltr. complete all as specified and as directed. 100 M & L PCC 1:2:4 type B-0 (12.50mm graded aggregate) as in padding finished even and smooth without using extra cement complete all as specified and as directed. 101 Taking down chowkats or framesexceeding n.exc. 1.5 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed. 102 Taking downshutters of any description exc 1.00 Sqm and not exc 2.00 Sqm each complete all as specified and as directed. 103 Taking down chowkats or framesexceeding 1.5 Sqm and n.exc 4.00 sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed. 104 S & F 35mm thickplain framed panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12mm veneered board with commercial veneering on both faces.The size of rail and stile as per IS -1003 (Part-I) klin seasoned and chemically pressure treated complete all as spd and directed (2nd class hard wood rail and stile) all as spd & directed. 105 S & F 35mm thickglazed & skeleton shutters of 2nd class hard wood, open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as spd in SSR Part-I section 8 clause 8.2 (A) complete all as specified and as directed. 106 M & L Pressed steel frames factory made for doors out of 1.25mm thick PBI sheet with one of more rebates including necessary flat iron lugs, hinges, lock strike plate, hinges etc complete, size of frame 125x60mm complete all as specified and directed 107 M & L Pressed steel frames factory made for doors out of 1.25mm thick PBI sheet with one of more rebates including necessary flat iron lugs, hinges, lock strike plate, hinges etc complete, size of frame 105x60mm complete all as specified and directed 108 S & F Aluminum anodized barrel tower bolt extruded section 150mm longcomplete all as specified and as directed. 109 S & F 300 mm long aluminum alloy, anodized, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded section & fixing blots & sliding bolts of extruded section or cast aluminum alloy & fixed complete all as specified and as directed. 110 S & F in Aluminum anodized handles fabricated type of 150mm long complete all as specified and as directed. 111 M & L Box type Steel window side hung double shutters with provision for desert cooler/AC(inside for wire mesh & out side for glass), including guard bar,hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded and fixed, steel window shall be conforming torelevant IS complete all as shown on drawing No CEUZ/TD/1302/09, Sh 1/3 to 3/3 and directed. Note:- Wire mesh and sheet glass shall be measured and paid separately 112 M & L Box type Steel ventilators top hung double shutters (inside for wire mesh & out side for glass), including hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing.Steel window shall be conforming torelevant IS all as specified.Note:- Wire mesh and sheet glass shall be measured and paid separately 113 M & L for, Preparing of new untreated steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide primercomplete all as specified and as directed. 114 M & L for 18/19 mm thick solid PVC board, as in cupboard shutters, partition walls and shelves fixed with frame complete all as specified and directed. 115 M & L Anodised aluminium window frame powder coated double rebated(16 gauge aluminium sectionISImarked, weighing not less than 0.55 Kg/RM ,size of frame 100mm )incl side hung /sliding glazedshutter and wire gauged window shutter, 5 mm thick tinted sheet glass selected quality of any colour, wire gauge ,hinges, necessary jointing cleat, glazing clips, rubber packing, aluminium handle etc, . and includingopening of AC complete,including taking down old window of any type(Design/pattern of the frame as approved by Engineer in Charge all as specified and directed.) 116 M & Lfabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly panelled with 9 mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200 mm size etc including taking down or and making good of disturbed surface all as specified below complete all as specified and directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4 mm ( Section No 14021) (b) Vertical Members of shutter Section shall be be of size 85.00 x 44.45 x 2.00 mm (Section No 19560) (c) Top Members of shutter Section shall be be of size 83.50 x 44.45 x 2.00 mm (Section No 19581) (d) Lock rail (Middle member) of shutter Section shall be be of size 150.00 x 44.45 x 3.00 mm (Section No 19596)(e) Bottom Members of shutter Section shall be be of size 150.00 x 44.45 x 3.10 mm(Section No 19584)(f) Glazing clip for securing glass of shutters shall be be of 0.80 mm thick (Section No 19370).Make- Jinal Section, 117 M/L 75 mm thick Cement concrete type B2, 1:2:4 (using 40 mm graded granite stone aggregate) in base of flooring/ hard standing finished evern & smooth w/o using extra cement.. complete all as specified and as directed. 118 M & L for 20mm thick screed screed bedding in cement mortar 1:6 as in sub base. complete all as specified and as directed. 119 M & L Chequered cementconcrete tiles of size 30cm x 30cm x 20 to 22 mm thickglossy finish colouredand pattern in patches in floor with set & jointed in neat cement slurry and pointed in coloured cement to match the tiles laid over with grey cement and no pigment complete all as specified and directed. 120 M & L for Preparation of surfaces incl brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts over all decorated plastered or un plastered surfaces of wall incl cornices etc and applying one coat of white wash upto four storie build complete all as specified and as directed. 121 All as per item No 120 here in before but applying two coats of white washingcomplete all as specified and as directed. 122 All as per item No 120 here in before but applying one coats of white washing on ceiling complete all as specified and as directed.. 123 All as per srl item No 120 here in before but applying one coat of cement base paint on walls complete all as specified and as directed.. 124 All as per srl item No 120 here in before but applying two coat of cement base paint on walls complete all as specified and as directed.. 125 All as per srl item No 120 here in before but applying one coat of oil bound distemper on wall complete all as specified and as directed. 126 All as per srl item No 120 here in before but applying two coat of oil bound distemper on wall complete all as specified and as directed.. 127 M & L preparing new plastered surfaces of wallsand applying Finishing of wall with acrylic smooth exterior paint of required paint of required shade new work (two or more coat applied @ 1.67ltr/10Sqm and including priming coat of exterior primer applied @ 2.2 Kg/10 Sqm).complete all as specified and as directed. 128 M & L for complete removal of existing trreatment preparing old plastered surfaces of wallsand applying Finishing of wall with acrylic smooth exterior paint of required paint of required shade new work (two or more coat applied @ 1.67ltr/10Sqm and including priming coat of exterior primer applied @ 2.2 Kg/10 Sqm).complete all as specified and as directed. 129 M & L for Preparation of newly plastered surfces of walls and applying Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification. Two or more coats on new workover a coat of wall care putty 3mm thick complete all as specified and as directed. 130 M & L for Preparation of Complete removal of existing trreatment preparing old plastered surfaces of walls and applying Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification. Two or more coats on new workover a coat of wall care putty 3mm thick complete all as specified and as directed. 131 M & L for Preparation of newly plastered surfces of Ceiling and applying two coats of oil bounddistemper over a coat of wall care putty 3mm thick complete all as specified and as directed. 132 M & L for Preparation of Complete removal of existing trreatment preparing old plastered surfaces of Ceiling and applying two coats of oil bounddistemper over a coat of wall care putty 3mm thick complete all as specified and as directed. 133 Taking down cement plaster on brick or stone surfaces etc. including raking out joints, hacking for key, scrubbing down with water etc.,complete all as specified and as directed. 134 M & L 15mm thick plastering in CM 1:4 on stone surfaces (EXTERNAL), surface finished even and smooth without using extra cement, complete all as specified and as directed. 135 M& L 15mm thick plastering in CM 1:6 on stone surfaces (INTERNAL), surface finished even and smooth without using extra cement. complete all as specified and as directed. 136 M&L rendering 5mm thick in cm (1:3)as in ceiling , soffit of chajja etc.complete all as specified. 137 M & L for Preparing of previously painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. 138 Note:(i) Cost of labour for providing new items including replacement /Demolition/ dismantling/ taking out/down of old unserviceable item shall be deemed under respective item. (ii) Cost of material shall be measured and paid separately under relevant items 1 to 137 as given below.(iii) Supervisor will collect the complaints from the complaint cell and complete the same and give feedbackto the concerned JE on same day 139 SCHEDULE-A PART-II (E/M WORKS)Identifying and rectifyingthe defects pertaining to internal electrification of any type and nature such as taking down defective switch/socket/ceiling rose/holders/fittings / fixtures any type, rectification of faulty electric circuits,tightening of loose connections, replacment of old u/s wiring/conduits/casing caping & connections etc.complete all as specified and as directed. 140 Identifying and rectifyingthe defects pertaining to internal electrification of any type and nature such as taking down defective MCBs / MCB DBs/TPN/ TPN DBs any type, rectification of faulty electric circuits,tightening of loose connections, replacment of old u/s wiring/conduits/casing caping & connections etc.complete all as specified and as directed.NOTE FOR ITEM NO 138 & 139 :- (a)All T & P/Stationeries and labour team required comprising of Nos of trained electricians & helpers will be provided by the contractor daily, as directed.(b) Repof the contractor will present in complaint cell & responsible for receiving & attending the complaints from 08.30 Hrs to 04.30 Hrsthe time of lodging the complaint. In absence of rep of Contractor penal recovery as decided by GE shall be imposed & on contractor.(c) Cost of minor stores such as screws,clamps,insulation tapes,nuts/bolts, nail of required size etc shall be deemed included in the above quoted item. However, major items such as switches, sockets, bell push, fan regulator etc shall be measured and paid separately under appropriate items of Schedule A. (d) Complaints where complete replacement of circuit/point wiring required shall be measured under relevent item. (e) If contractor fails to rectify the complaint with in 24 hours after reciving, Rs 1000/- per complaint will be penalised. 141 Supply and fixin replacement ofswitch piano flush type 5 Amps single pole one waycomplete all as specified and as directed. 142 Supply and fixin replacement ofsocket out let multipurpose suitable for 2/3 pin 5 amp flush typecomplete all as specified and as directed. 143 Supply and fixin replacement of switch socket combination 2 in 1, 3 pin, 5 Amp flush typecomplete all as specified and as directed. 144 Supply and fixin replacement of switch socket combination 2 in 1 5 pin 5 /15 Amps flush type complete all as specified and as directed. 145 Supply and fixin replacement of, ceiling rose surface type 65mm x 50mm 2 to 3 terminalcomplete all as specified and as directed. 146 Supply and fixin replacement of, Step type fan regulator 300 watt, 230 volts, 50 HZ, AC.complete all as specified and as directed.. 147 Supply and fixin replacement of, Batten/angle type holder insulated body with back platecomplete all as specified and as directed. 148 Supply and fixin replacement of, bell pushpiano type 5 Ampscomplete all as specified and as directed. 149 Supply and fixin replacement of, electric bell ding dong230 volt ACcomplete all as specified and as directed. 150 Supply and fixin replacement of, Integrel sleek extrudedbatten aluminium /CRCAchannel fitting with LED20 watt complete with all accessories 230V 50 Hz complete all as specified and as directed. 151 Supply and fixin replacement of baton integrated LED channel of 10W, 230V frequency 50/60 Hzintegral sleek extruded polycarbonate LED channel with white acrylic cover, Power Factor not less then 0.9complete all as specified and as directed. 152 Supply and fixin replacement of, white powder coated (warm / white / cool white) CRCA housing with LEDs 36W, 230 V, 50 Hzrecess mounting LED 2 feet x 2 feet luminaries, Swamless front frame with flat white hight transmission acrylic cover complete with all accessories including connecting up with twin core twisted flexible copper conductor cable with suitable size.complete all as specified and as directed. 153 M&L LED light fitting 1x9W bulk head luminaries IP 65 complete with all accessories includingLED lamp 9 watt , connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V 50 Hz .complete all as specified and as directed. 154 Supply and fixing of LED Inverter Batten 9 Watt 230V frequency 50/60 Hz back up to 4 to 6 Houses including connecting up with twin core twisted flexible copper conductor cable with suitable sizecomplete all as specified and as directed. 155 Supply and fix in in replacementof LED bulb white / warm / cool white 9 wattcomplete all as specified and directed. 156 Supply and fix inin replacement, modular switch piano flush type, 6 amps, 230V AC,single pole, one way,complete all as specified and as directed. 157 Supply and fixin replacement, modular switch piano flush type, 16 amps, 230V AC,single pole, one way,complete all as specified and as directed. 158 Supply and fix in in replacementof modular socket out let with shutter multipurpose suitable for 2 pin and 3 pin 6 amp flush type,complete all as specified and as directed. 159 Supply and fix in in replacementof modular socket out let with shutter multipurpose suitable for 6 pin 16 amp, flush typecomplete all as specified and as directed. 160 Supply and fix in in replacementofmodular bell swith,6Amp, 220 V, single pole complete all as specified and directed. 161 Supply and fix in in replacementof Electronic modularfan regulator ,Two module, electronic,step type and connectioncomplete all as specified and as directed. 162 Supply and fix in in replacementof MCBDP 32/40 Amps 10 KA 230 volts C seriescomplete all as specified and as directed. 163 Supply and fix in in replacementof MCB single pole 6 to 32 Amps 10 KA 230 volts C seriescomplete all as specified and as directed. 164 Supply and fix in in replacementof MCB single pole 40/63 Amps 10 KA 230 volts C series complete all as specified and as directed. 165 Supply and fix in in replacementofMCB TP/TPN 10 to 63 Amps 10 KA 230 volts C series complete all as specified and as directed. 166 Taking down carefully unserviceable aluminium point wiring (light, fan, socket bell or power) complete, (fittings such as switches, ceiling rose lamp holder, regulators, sockets, pendants) stackingat site and keeping in safe custody for taking credit, complete all as specified and as directed. 167 Taking down unserviceable MCB DB SPN with MCBs of any make/capacity,complete all as specified and as directed. 168 Taking down unserviceable TPN DBwith MCBs of any make/capacity,complete all as specified and as directed. 169 Taking down unserviceable sub main wiring including wooden batten/PVC conduit of any size,complete all as specified and as directed. 170 M&L for point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including PVC casing capingISI markednot less than 20mm wide on wall /ceiling with allfittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2 mm thick covered with3 mm thick bakelite laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5 sqmm FRLS multi stranded copper conductordrawing as continuous earth wire connected to main earth and earth dollyfor One light point / fan point/ bell point controlled by one switch 5 Amp complete all as specified and directed. 171 All As per Srl item N0 169 above for one socket out let 5 Amp controlled by one switch on independent board with other switch . 172 All as per item No 169 here in before but point wiring for one 3 pin 15 Amp socket outlet point controlled by one switch using 2.5 sqmm copper conductor cable with continuous earth wire of 2.5 sqmm copper conductor on independent boardcomplete all as specified and as directed. 173 S&F sheet metal enclosuredistribution board SPN 12 way230 V, 50 Hz double doorwith neutral, Earthing bar and din railcomplete all as specified and as directed. 174 S&F sheet metal enclosure (VTPN) double door for distribution board factory made for MCB DB load link VTPN 4 way including MCCB 125 Amp, 4 pole as incomer. (when MCBs are to be used) with suitable size of busbar complete,fixed flush in wall including chases wall for fixing DB and making goodthe distributed wall surfaces to match with existing specification including taking downcomplete all as specified and as directed. 175 M&L for sub main wiring with two single core FRLSPVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 4 Sq mm drawing through and includingconcealed rigid non metallic PVC conduit medium grade ISI marked 20 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 4 sq mmas earth continuity conductorconnected to commen earth and earth dollycomplete all as specified and as directed. 176 Disconnecting & Taking down unserviceable ceiling fan 1400/1200 mm sweep 230 v, AC supply, single phase from positionfor windingand refixing for the same after winding,necessary connection comple all as specified and directed . Note winding and including repairs measured separately. 177 All as per item No 175here-in-before but exhaust fan of size 450/380/300 /255mm sweepcomplete all as specified and as directed. 178 All as per item No 175here-in-before but wall mounted fan size 450/400 mm sweepcomplete all as specified and as directed. 179 M&L for collecting unserviceable ceiling fans 1200mm sweep 230 v, AC supply, single phase from E/M store yard of GE Nagrota , Dismantling the ceiling fan and taking out complete burnt windingfrom fan motor and rewinding the same with super enameled copper winding wire of existing gauge & size including thoroughly cleaning all the components of fan, oiling , greesing & painting with one coat of syntetic enemel paint after scrbbing and perparing the old painted surface of the fan with and including replacement of rusted /unserviceable nuts, bolts split pin rubber reel , machine screws, shaftetc including replacement of defective / unserviceable parts / spares as required reassembling the fan and testing complete deposinging the complete repaired fan to E/M store yard of GE Nagrota including transportation complete all as specified and derected. 180 All as per item No 178 here-in-before but ceiling fan of size 1400 mm sweepcomplete all as specified and as directed. 181 M&L for collecting unserviceable exhaust fan 450mmsweep 230 V, AC supply, single phase from E/M store yard of GE Nagrota , Dismantling the exhaustfan and taking out complete burnt windingfrom exhaust fan motor and rewinding the same with super enameled copper winding wire of existing gauge & size including thoroughly cleaning all the components of fan, oiling & greesing painting with one coat of syntetic enemel paint after scrbbing and perparing the old painted surface replacement of rubber pads and depositing the exhaust fan to E/M store yard GE Nagrota including transportation and testing etc complete all as specified and derected. 182 All as per item No 180here-in-before but exhaust fan of size380 mm sweepcomplete all as specified and as directed. 183 All as per item No 180 here-in-before but exhaust fan of size 300 mm sweepcomplete all as specified and as directed. 184 M&L for collecting unserviceable PVC exhaust fan 250/300 mmsweep 230 V, AC supply, single phase from E/M store yard of GE Nagrota , Dismantling the exhaustfan and taking out complete burnt windingfrom PVC exhaust fan motor and rewinding the same with super enameled copper winding wire of existing gauge & size including thoroughly cleaning all the components of fan, oiling & greesingand depositing the exhaust fan to E/M store yard GE Nagrota including transportation and testing etc complete all as specified and derected. 185 M&L for collecting unserviceable wall mounted fan 450/400mm, sweep 230 V, AC supply, single phase from E/M store yard of GE Nagrota , Dismantling the wall mounted fan and taking out complete burnt windingfrom wall mounted fan motor and rewinding the same with super enameled copper winding wire of existing gauge & size including thoroughly cleaning all the components of fan, oiling & greesing painting with one coat of syntetic enemel paint after scrbbing and perparing the old painted surface replacement of rubber pads and depositing the wall mounted fan to E/M store yard GE Nagrota including transportation and testing etc complete all as specified and derected. 186 Taking down carefully from position , ceiling fan 230 volts single phase50 Hz1400 mm sweep from the position & removing/ cleaningof dust properly, oiling and greasing of bearing including necessary repairs andrefixing and connectingup with all requisite accessories complete all as specified and directed. Note ;necessary accessaries paid seperatelyhere in after. 187 All as per item No 185 here-in-before but ceiling fan of size 1200 mm sweepcomplete all as specified and as directed. 188 Taking down carefully exhaust fan 230 volts single phase50 Hz450 mm sweep from the position & removing/ cleaningof dust properly, oiling and greasing of bearing including necessary repairs andrefixing and connectingup with all requisite accessories complete all as specified and directed. Note ;necessary accessaries paid seperatelyhere in after 189 All as per item No 187here-in-before but exhaust fan of size 300/380mm sweepcomplete all as specified and as directed. 190 Taking down carefully wall mountedfan 230 volts single phase50 Hz450 mm sweep from the position & removing/ cleaningof dust properly, oiling and greasing of bearing including necessary repairs andrefixing and connectingup with all requisite accessories complete all as specified and directed. Note ;necessary accessaries paid seperatelyhere in after. 191 Supply and fixin replacement of gun metal bush of required size suitable for ceiling fans and exhaut fans complete all as specified and directed 192 Supply and fixin replacement of hanger for ceiling fan 1200mm/ 1400 mm sweep with nuts, bolts, washers complete all as specified and directed. 193 Supply and fixin replacement ofaluminium blades for ceiling fan 1200 mm sweepcomplete all as specified and directed 194 Supply and fixin replacement of aluminium blades for ceiling fan 1400 mm sweepcomplete all as specified and directed 195 Supply and fixin replacement of bearing suitable for ceiling fan of any size complete all as specified and directed 196 Supply and fixin replacement of bearing suitable for Exhaust fan/Air circulator/wall mounted fan of any size complete all as specified and directed 197 M&L scrbbing and preparing the old painted surfaces of ceiling fan of size 1200/1400mm sweep (Make :- Kessels /Usha / Orient / Crompton / Cool home / Bajaj/ Polar ) Completeincluding blade painting the same with white duco paint and writing the MES Nos of the fans, 25mm with black synthetic enamel paint and including oiling greasing ofany make complete all as specefied and directed. 198 M&L scrubbing and preparing the old painted surfaces of exhaust fan of size 300/450mm sweepcompleteincluding blade painting the same with white duco paint and writing the MES Nos of the fans, 25mm with black synthetic enamel paint and including oiling greasing ofany make complete all as specefied and directed. 199 Supply & Fix canopy top and bottom for ceiling fans complete all a spcified and directed. 200 S & F in repairs flexible twin core 23/0.0076 with copper conductor including connecting fan of any make complete all as specified and directed. 201 S&F 250/300 mm long fan down rod with clamp heavy duty as required in replacement complete all as specified and directed. 202 S&F exhaust fan frame made out of MS sheet of any make and size of exhaust fan with suitable size of nut bolt and washerscomplete all as specified and directed 203 Material and labour for replacement of Unserviceable Louvers with new louvers of exhaust fan 450mm sweep complete all as specified and directed. 204 Material and labour for replacement of Unserviceable Louvers with new louvers of exhaust fan /250300/380 mm sweep complete all as specified and directed. 205 S&F in repairs oil filled condenser of 2.5 MFD capacity after removing existing unserviceable condenser from any situation complete all as specified and directed, 206 All as per item No 204 here-in-before but condenser 4 MFD capacity 207 Supply & fix blade suitable for wall mounted fan 400/450 mm sweep fan complete all as specified and directed 208 Supply & fix in replacement for shackle assembly for cieling.fan complete all as specified and directed 209 Taking down the water heater storage type of any make of any capacity. dismantling the water heater carefully from its position fixed on walls, reassembling the water heater after replacement of defective parts and reinstalling the water heaters to their original locations or as directed, commissioning and testing the water heater complete, all as directed by the Engr-in-charge.Note: Any material/part found unserviceable during servicing shall be replaced by the contractor and measured and paid separately under respective items. 210 S&F in place of unsv PVC connectionof any make with (ISI Mark) having10mm dia, 45 cm long with steel reinforcementsuitable for hot water geyser outlet supply with 02 Nos of Unions/ cup shapedcover withwashers complete all as specified and directed 211 S&F in place of un PVC connectionof any make with (ISI Mark) having 10mm dia, 45 cm long suitable for cold water geyser inlet with 02 Nos of Unions/ cup shaped PVC cover withwashers complete all as specified and directed 212 S&F in place of unserviceable inner tank of 25 litres capacity water heater storage type, tank made out of copper sheet of size 22SWG, MS collar with six/seven/eight/ nine holes for fitting the flange assembly with vent pipe of brass, 3 “ long, 15 mm dia, threaded, including MS sheet ring complete all as specified and directed 213 All as per srl item 211 above but of 35/ 50 litres capacity. complete all as specified and directed 214 S&F in replacementof unserviceable inlet /outlet assembly of any make of geyser havingsix/seven/eight /nine hole suitable for Bathwell/ Bajaj / pearl water heater of capacity 25/50litre complete all as specified and directed 215 S&F in replacementof unsv rubber gasket suitable for six/seven/eight/ nine hole assembly of suitable size of water heater of capacity 50/35/25 ltr. 216 S&F in replacement of unsv4 long and 1/2 dia Chrome plated bolt with suitable washers complete all as specified and directed 217 S&F in replacement of unsv split bottom cover (two pieces) suitable for water heater of any capacity duly painted, complete all as specified and directed 218 S&F in replacementof unsv neon indicating lamp, rectangular /round as required at site, complete all as specified and directed 219 S&F in replacement of unsvheating element 1.5 KW, single phase, 230 volt with triangular base suitable for 25/50 Ltr water heater. complete all as specified and directed 220 S&F in replacement of unsvheating element 2.0 KW, single phase, 230 volt with triangular base suitable for 25/50 Ltr water heater.complete all as specified and directed 221 S&F in replacement of unsvheating element 1.5 KW, single phase, 230 volt with round base suitable for 25/50 Ltr water heater complete all as specified and directed 222 S&F in replacement of thermostat switchrange upto 80”C suitable for 25/50 ltrs cap water heater. complete all as specified and directed 223 S&F in replacement of unserviceableplug top 3 pin 15 Amps. complete all as specified and directed 224 S&F in replacement of unserviceable safety nut for geyser of capacity 25/50 ltrs. complete all as specified and directed 225 M & L for Painting to outer body ofgeyser of capacity 25/35/50 ltr with white synthetic enamel paint of approved make after preparation of surface including filling cavities with filler of complete all as specified and directed 226 Supply and fixin replacement of electric water heater,storage type steel body with copperinner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed 227 M&L in replacement of sub main wiring with two single core FRLSPVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6 Sq mm drawing through and includingconcealed rigid non metallic PVC conduit medium grade ISI marked minimum 20 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6 sq mmas earth continuity conductorconnected to commen earth and earth dolly complete including taking down existing UNSV. complete all as specified and directed 228 Supply and fix in replacement ofexhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed 229 Supply and fix in replacement of exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m incl cutting of hole of suitable size and making good after installation of exhaust fan at site complete all as specified and directed 230 Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed 231 M & L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not lessthan 1.5 metres below normalground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicatedincluding testing on completion complete all as specified and directed 232 M & L for Dismantling the solar panel (made of flat collector plates) of any description, material and labour forcleaning the glass by washing with using soft detergent, cleaning & de-scalingthe inside surface of copper fins / tubeswith suitable size of drill rod, wire brush &with circulating concentrated de-scaling solution(ORISCALE BLASTER) mixed with water in suitable proportion circulating through pump till the complete deposits/scale is removed and approved by the Engineer-in-Charge, brazing the leaking copper tubes, fixing the copper tube & fins properly in their respective positions, reassembling the solar system after servicing / maintenanceincluding replacement of flanges made out of gun metal,nuts, bolts & washers, gaskets etc., fixing & installation of the solar flat collector plate in position and its testing to the entire satisfaction of Engineer-in-Charge. 233 M & L for Opening of existing aluminium cladding from tank ,cleaning and stacking the same for reuse ,taking out glass wool and repairing the stainless steel tank and repairing the leakage by means of TIG welding as approved ,refilling of glass wool ,aluminium cladding by using old aluminium sheet complete all as directed by Engr- in -charge. Note:- Existing glass wool and aluminium sheet shall be reused, new glass wool and aluminium sheet if required shall be not measured and paid for separately complete all as specified and directed by Engineer-in-Charge. 234 Disconnecting and taking out old existing unserviceable water heating element of any description and in any position and supply, fixing new water heating elementhexagonal/ Rectangular/circle type of capacity 5 KW with suitable thermostat as per existing site including all necessary fittings complete all as specified and directed. 235 Disconnecting and taking out old existing unserviceable water heating element of any description and in any position and supply, fixing new water heating elementhexagonal/ Rectangular/circle type of capacity 3 KW with suitable thermostat as per existing site including all necessary fittings complete all as specified and directed. 236 M & L for refixing of Solar plate at the site complete all as specified and directed by Engr-In-Charge. 237 Material andLabour for servicing of following appliances comprising of through cleaning, lubricating of all moving parts, replacement of wornout screws, bolts etc to make the unit for smooth operation for the following capacity of water cooler / refrigerator & Deep Freezers :- complete all as specified and directed. 238 Water coolers 40 to 150 ltrs cooling capacity. 239 Refrigerator of 165 to 310 ltrs capacity. 240 Deep Freezers any capacity 241 Supply and replacement ofcompressor sealed unit of the following appliances of any make complete including replacement of copper tubing/capillary strainer etc, testing and commissioning all as specified and as directed by Engr-in-Charge. 242 Water coolers of capacity up to 150liters. 243 Refrigerators of capacity 210 to 320 ltrs. 244 Deep freezers 100 to 400 ltrs capacity. 245 Supply and fix inreplacement ofstarting relay suitable for :- Make : as per exiting makecomplete all as specified and directed 246 Water coolers 40 to 150 ltrs cooling capacity 247 Refrigerator of 165 to 320 liters capacity. 248 Deep freezers of 100 to 400 ltrs capacity. 249 Supply andfix in replacement ofthermostats of :-Make : as per exiting makecomplete all as specified and directed 250 Water coolers 40 to 150 ltrs cooling capacity. 251 Refrigerator of 165 to 320 ltrs capacity. 252 Deep freezers of 100 to 400 ltrs capacity. 253 Supply andcharging refrigerant gas R-22/R-134 (A)up to required level incl connected works like pressure testing with nitrogen before filling refrigerant gas including leakage testing if any complete all as specified and directed by Engr-in-Charge 254 Water cooler 40/80 ltr cooling cap. 255 Water cooler 60/120 ltr cooling cap. 256 Water cooler 150/150 ltrs cooling cap 257 Deep freezers ofany capacity. 258 Refrigerators of any capacity. 259 Supply and fix inreplacement ofcondenser coil unit of the following appliances including making of all connections as specified and directed by Engr-in-Charge. Make : as per exiting make 260 Water coolers 40 to150 ltrs capacity. 261 Refrigerator of 165 to 320 ltrs capacity. 262 Deep freezers of 200 to 400 ltrs capacity. 263 Supply & Fix Timer delay Relay assembly in replacement of unserviceable Relay assemblyof any cap complete all as specified and directed by Engr-in ChargeMake : as per exiting make 264 Water coolers 40 to150 ltrs capacity. 265 Refrigerator of 165 to 320 ltrs capacity. 266 Deep freezers of 200 to 400 ltrs capacity. 267 Supply andfix inreplacement oftop cover gasket of water cooler 40 to 150 ltrs capacity.complete all as specified and directed 268 Supply and replacement ofoverload protector of :-Make : as per exiting makecomplete all as specified and directed 269 Water coolersupto 150 ltrs cooling capacity. 270 Refrigarator upto 320 ltrs cooling capacity. 271 Deep freezers of upto 400 ltrs capacity. 272 Supply and replacement ofblower/condenser fan motor complete with necessary mounting bracket to and base frames for :-Make : as per exiting makecomplete all as specified and directed 273 Water coolers of any make and cap 40 to 150 ltrs capacity. 274 Deep freezers of any make & cap 100 to 400 ltrs capacity. 275 Supply and replacement ofcapacitors of the following capacities for Acscomplete all as specified and directed 276 3.15 ,4 & 6 Mfd 277 10 Mfd 278 40/60 Mfd 279 50+6 Mfd Seven Pin 280 Taking down existing unserviceable fan motor assembly complete with blades mounting frame leg with rubber bush from desert coolers and S&F Fan motor assembly complete with blades, mounting frames legs with rubber bush for desert cooler of capacity 4000/5000/6000 cum/hrs and testing complete all as specified and as directed. 281 Supply & Fix Replacement of water circulation submersible pump of desert coolersuitable for operation on AC supply single phase230/250 volts 50 Hz. complete all as specified and directed. 282 Taking out existing old wood wool pads from desert coolers and S&Fwood wool padswith nylon threads suitable for any make of desert cooler having minimum/maximum capacity 3000 cum/hr and 5000 cum hrs including S&F PVC insulated protective guards for holding the wood pads complete all as specified and as directed. 283 Supply & Fix outer body of desert cooler 4000/5000/6000 cum/hrs capacity made out of galvanized iron sheets with bottom tank of 22 gauge, top cover of 24 gauge and side panels of 22 gauge GI sheet duly fitted with 2” thick wood wool pads including on heavy duty 22 guage frontgrill fitted with one piano type 5 Amps switch three speed selector switch of approved make with arrangement of changing the direction of air flowin replacement of unserviceable body complete all as directed. 284 M & Lfor Replacement of PVC water distribution system 4 way suitable for 3000/4000/5000/6000 Cum/Hrs of desert coolers complete with PVC Elbow, PVC Pipe (distribution system to side panel with elbow at end )heavy duty 15mm dia complete all as specified and directed. 285 Supply & Fix three speed selector switch complete with knob of approved make for desert cooler in replacement of unserviceable three speed selector switch complete all as specified and directed. 286 M & L for Replacement of unserviceable side panels with wood wool 2 thick for desert cooler made out of 22 gauge plane GI sheet of existing size of desert cooler complete. (EachSet Of Three Panels) complete all as specified and directed. 287 M & L for Replacement of damaged/rusted front grill made out GI sheet of 20 gauge heavy duty complete with knob to separate the shutter and S&F one piano type switch 6 Ampand one three speed selector switch complete all as specified and directed. 288 M & L for Painting of desert coolers in side out side at site of work with two coats of synthetic enamel paint grey or any other shade (as approved) from out side complete including shutters top, bottom with spray painting machine and in side with black anti – corrosive paint (two coats) complete all as specified and directed. 289 Supply & FixPush cockof brass outer thread type15mm chromium plated in replacement of unserviceable Push cock complete all as specified and directed. 290 Supply & FixPush cockof brass inner thread type15mm chromium plated in replacement of unserviceable Push cock complete all as specified and directed. 291 M & L for Rewinding of voltage stabilizer single phase AC 230 volts 50 C/S with super enameled copper wire of suitable gauge to match with the existing one including all related work and testing complete of size capacity 2/3 KVA complete all as specified and directed. 292 M & L for Rewinding of voltage stabilizer single phase AC 230 volts 50 C/S with super enemalled copper wire of suitable guage to match with the existing one including all related work and testing complete of size capacity 4 KVA complete all as specified and directed. 293 M & L for Rewinding of voltage stabilizer single phase AC 230 volts 50 C/S with super enemalled copper wire of suitable guage to match with the existing one including all related work and testing complete of size capacity 5 KVA complete all as specified and directed. 294 M & L for Rewinding of voltage stabilizer single phase AC 230 volts 50 C/S with super enemalled copper wire of suitable guage to match with the existing one including all related work and testing complete of size capacity 6 KVA complete all as specified and directed. 295 M & L for Replacement limit switch suitable for SP voltage stabilizer capacity 1/3/5 KVA complete all as specified and directed. 296 Supply & Fix PVC float valve assembly in replacement of unserviceable PVC float valve assembly for water coolers of any capacity complete all as specified and directed. 297 Supply & Fixfreezer cabinet suitable for cap upto 280 liters cap refrigerator in replacement of unserviceable freezer cabinet complete all as specified and directed. 298 Supply & Fixfreezer cabinet suitable for 300/ 320 liters cap refrigerator in replacement of unserviceable freezer cabinet complete all as specified and directed. 299 S & F in Single pole and neutral enclosure with a two pin and earth plug and socket20 A ,240 V complete with one single pole MCB complete all as specified and directed. 300 Supply and fix 16 A 3 Pin plug top 240 V complete all as specified and directed 301 Supply and fix 6 A 3 Pin plug top 240 V complete all as specified and directed 302 Supply & Fix Bulb in replacement of unserviceable Bulb suitablefor refrigerator of any size complete all as specified and directed 303 Supply & Fix Waste water tray in replacement of unserviceable Waste water tray suitable for refrigerator of any size complete all as specified and directed 304 Supply and fix PVC insulated Multicore standard Copper Cable 1.5 sqmm , 3 Core complete all as specified and directed. 305 Supply and fix PVC insulated Multicore standard Copper Cable 2.5 sqmm , 3 Core complete all as specified and directed. 306 Supply and fixingGI tubings medium grade 15 mm bore dia ISI Mark with all fittings such as elbow, bends, sockets, nipples and union etc and fixed complete laid in trench/wall/floorfor the following sizes including taking down of existing old GI pipes complete all as specified and directed. 307 All item same as Ser item no 273but20 mm bore dia complete all as specified and directed. 308 Supply and Fixing 15 mm Gun metal Globe or gate valve with iron wheel head screwed both ends for iron pipe of the following bore sizes complete complete all as specified and directed. 309 All item same as Ser item no 275but20mm bore dia complete all as specified and directed.