Tender For Periodical Services, Kitchen Cabinet And Joinery Repair Works In Map And Billets Areas At Af-I Under Ge (Af) Jamnagar No.2- 1 M & L for complete removal of existing treatment of old decorated surfaces of walls, plastered or unplastered and cornices, by brooming down, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying two coats of white wash on walls complete all as specified and directed. 2 M & L for for complete removal of existing treatment of old decorated surfaces of ceilings, plastered or unplastered and cornices, by brooming down, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying two coats of white wash on ceilings complete all as specified and directed. 3 M&L for preparation of new plastered surfaces on ceilings and applying two coats of white wash complete all as specified and directed. 4 M & L for preparation of old distempered surfaces ofwall, distempered surfaces and applying one coat of oil bound distemperon walls complete all as specified and directed. 5 M & L for preparation of new plastered surfaces of walls and applying two coats of oil bound distempercomplete all as specified and directed. 6 M&L for complete removal of existing treatment on old surfaces including brooming down, scrapping down smoke soot, mould, moss and efforescent salts and trading oil and grease spouts and cleaning with water on wall applying one coat of Acrylic emulsion (Exterior weather coat) paint of any tint as approved complete all as specified and directed. 7 M&L for preparation of old decorated surfaces of walls and providing one Coat of cement base paint complete all as specified and directed. 8 M&L for preparation of old wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 9 M&L for preparation of old painted of steel or iron surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 10 M&L for repairing of chajja / roof projection by taking down old plaster, damaged concrete surface, cutting of exposed reinforcement and making good with CM 1:4 including admixture of SBR (cost of SBR including) as per manufacture, and provide reinforcement cement concrete 1:2:4type B1 as required, necessary scaffolding, formwork etc up to 9 Mtr height andapplying 10 mm thick rendring in cement mortar 1:3, finishing the surface even & smooth without using extra cement complete all as specified and directed.Note: Reinforcement will be meansured paid separately. 11 Dismantling of floor, hearth or wall tiling, incl cement mortar bedding (but not backing) and rubbish off the premises including removal of debris to a distance exc 1.5 but n exc 2.00 km complete all as specified and directed. 12 Demolition of cement concrete(unreinforced) in ground floors and pavings n.exc 15 cm thickness (below or above G.L) complete all as specified and directed. 13 M & L for 25 mm thick cement concrete type B0 1:2:4(using 12.5 mm graded aggregate) as in levelling course in flooring complete all as specified. 14 M&L Non - skid joint free coloured Ceramic tiles (1st quality) not less than 7-8 mm thick of size exc 0.06 sqm but n exc 0.11 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over & including 15mm screed bed or bedding in CM 1:6 complete all as specified and directed. 15 M&L Non - skid joint free coloured Ceramic tiles (1st quality) not less than 7-8 mm thick of size exc 0.11 sqm but n exc 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over & including 15mm screed bed or bedding in CM 1:6 complete all as specified and directed. 16 M&L for light shed vitrified coloured Ceramic tiles (1st quality) not less than 10 mm thick of size 600x600 mm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over & including 15mm screed bed or bedding in CM 1:6 complete all as specified and directed. 17 M&L for joint free (edge cut) coloured glazed ceramic tiles thickness not less than 7-8 mm size of tiles 300mmx450mm as in skirting / dado etc laid jointed in neat cement slurry and pointed with coloured cement to match the tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed. 18 Taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc,including removal of debries to a distance exc 1.5 Km but n. exc 2 Km. complete all as specified and directed. 19 M&L for rendering 10mm thick in CM 1:6 on brick or concrete surface or stone walls to be finished even and smooth (without using extra lime or cement) complete all as specified and directed . 20 M&L for rendering 15mm thick in CM 1:4 on brick or concrete surface or stone walls to be finished even and smooth (without using extra lime or cement) complete all as specified and directed . 21 M & L for cement plaster 5 mm thick in CM 1:3 on concrete surface as on ceilling finished even and smooth with out using extra cement complete all as specified and directed. 22 Taking down shutters of any description n.exc 1 Sqmeach complete all as specified and directed. 23 Taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm each complete all as specified and directed. 24 S&F for 100 mm long mild steel butt hinges, medium weight, cold rolled, mild steel and fixedcomplete all as specified and directed. 25 S&F 150 mm long aluminium anodised barrel tower bolt complete all as specified and directed. 26 S&F 150 mm long aluminium handle cast type anodised complete all as specified and directed. 27 S&F aluminum alloy anodized sliding door bolt with hasp and staple 300mm complete all as specified and directed. 28 S & F in repairs 150mm long aluminium anodised barrel tower bolt complete all as specified and directed. 29 S & F in repairs 100mm long aluminium anodised handle complete all as specified and directed. 30 S & F in repairs 300 mm long mildsteelordinary rat railrod pattern springs including roller and roller plate complete all as specified and directed. 31 S & F in repair 140mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. 32 S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. 33 S&F 35 mm thick factory made second class hardwoodGlazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass / gauge, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkhats complete all as specified and directed. 34 S & F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. 35 S&F 25 mm thick cupboard flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. 36 S & Fin repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed to wooden/metalic door/window shutters with aluminium wire staples or necessary rubber beading and screws complete all as specified and directed. 37 Dismantling of granite tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons cills or plateform etc complete all as specified and directed. 38 M&Lfor Granite work 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in coloured cement (1:2) using marble dust with admixture of pigment to match with granite shade, laid over and including 15 mm thick cement screed bed in CM 1:6 complete all as specified and directed. 39 S & F in repairs25 mm dia Curtain rails, mild steel, chromium plated with fixing brackets/concealed brackets & holders, stops, rollers etc.decorative typecomplete all as specified and directed. 40 Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed. 41 S&F 4 mmthick glass sheetordinary quality and glazing with oil putty/rubber beeding/ M seal etcn.exc 0.50 Sqm in each pane fixed to wooden/metalic frame complete all as specified and directed. 42 Supply fabricate & fix in position aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) three track window ( two shutters glazed & one shutters wiregauge) with frame, glazed with 4 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position, concelled type lock for all three shutter, PVC roller etc all as specified below, including taking down old window complete all as specified and directed. (a) Frame (top & side) section shall be of size 92.00 x 31.75 x 1.50 mm (Section No 20831) (b) Frame (bottom) section shall be of size 92.00 x 31.75 x 1.50 mm (Section No 20832) (c) Top & side Members of shutter Section shall be of size 18.00 x 40.00 x 1.55 mm (Section No 20738) (d) Shutter Interlock Section shall be of size 18.00 x 40.00 x 1.45 mm (Section No 20737) (e) Bottom Members of shutter Section shall be of size 18.00 x 40.00 x 1.55 mm (Section No 20736) Note:- Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx B 43 S&F aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) ventilator, partialy glazed and partialy louvers, outer frame & mullionfabricated with aluminium section of size 82.50 mm x 38.00 mm x 1.70 mm thick (Cat No 20036), half portion glazed with 4 mm thick frosted glass including rubber beading, & glazing clip, half portaion louvers of 80 mm wide & 4 mm thick frostade glass including aluminium louver patti including S.S wire gauge of fixing of 0.36mm dia and 1.40 width of aparture with 25x3mm think aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position including taking down old ventilator complete all as specified and directed.Note:-(i) Section No given above are of make Jinal, Contractor may use similar section of other make mention in Appx B 44 Taking down steel water tubing and connection 15mm dia bore and removal from site complete all as specified and directed. 45 Taking down steel water tubing and connection 20mm dia bore and removal from site complete all as specified and directed. 46 Taking down steel water tubing and connection 25mm dia bore and removal from site complete all as specified and directed. 47 S&F 15mm Tubes, Medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. 48 S&F 20mm Tubes, Medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. 49 Supply and fix 20 mm outer dia CPVCpipes SDR 11 & plain CPVC SER 11 fittings, fixed on wall concelled or exposed /ceiling or laying in floors complete all as specified and directed. Note:- Cutting chease wherever required will be measured & paid separately. 50 Supply and fix 25 mm outer dia CPVCpipes SDR 11 & plain CPVC SER 11 fittings, fixed on wall concelled or exposed /ceiling or laying in floors complete all as specified and directed. Note:- Cutting chease wherever required will be measured & paid separately. 51 M&L for cutting chases, of girth not exceeding 10 cm for concealed water tubing or concealed conduit wiring, etc. in stone / brick masonry wall built in cement mortar and making good, disturbed surface in Cement mortar 1:3 complete all as specified and directed. 52 S&F in repair vitreous china white wash down water closet pan(pedestal pattern) including fixing bolts,plastic seat cover with jet spray and including necessary flexible pipe connection complete all as specified and directed and removing debris out side MD land. 53 S&F in repairPVC valveless, syphonic action type, flushing cistern, low level with inlet, ball valve ,float and handle including brackets.(The colour will also perfectly match with the EWC.) complete all as specified and directed. 54 Supply and fix in repairs white vitreous china squatting pan ‘ORISSA’ pattern of size 580mm x 450 mm white with integral foot rests with cast iron ‘P’ or ‘S’ trap, front or back inlet including all connection and provision of lime concrete base complete all as specified and directed. 55 S&Fin repair white vitreous china wash hand basin of size580 x 440 mm, fixed over & including MS brackets comprising of the following items :-(a) Waste fitting 32 mm dia brass chromium plated with long screwed shanks and fly nut, flange end, bedded in red lead cement and other end fixed complete.(b) PVC waste pipe 32 mm dia 750 mm long complete. 56 S&F in repair 15 mm size bib cockcast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes complete all as specified and directed. 57 S&F in repair 15 mm size stop cock, cast copper alloy, chromium plated, fancy type with capstan head, concealed type, screwed down, screwed both end for iron pipes complete all as specified and directed. 58 S& F in repairs brass chromium plated shower rose 75 mm size with arms 15 mm inlet complete all as specified and directed. 59 S & F in repairs 15 mm size pillar taps, fancy type, cast copper alloy,chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nut, screwed for iron pipe complete all as specified and directed. 60 S & F 5.00 mm thick 600 x450 mm beveled edge mirror of selected quality glass mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 61 S&F in repair stainless steel kitchen plate rack of size 31 x 24 x 10 deep, fabricated with 0.63 mm sheet fixed in position on wall complete all as specified and directed. 62 S&F solid PVC door frame of size 50mmx 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and& sketch shown in section 8 of SSR part I complete all as specified and directed. 63 S&F Factory made solid PVC moulded door shutter 28 to 30mm thick (stiles) with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, suppling & fixing in the frame at site as per specification complete all as specified and directed. 64 S & F in repair brass chromium platedtubular towel rail 20 mm dia D type 60 cm long between flanges complete all as specified and directed. 65 S&F in repair Health Fauset (Hand shower) with 8mm dia 1 metre longeasy flex tube and in chorme finish & wall hookcomplete all as specified and directed. 66 S&F in repairs ballvalves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass ferrule and fixed 25mm dia complete all as specified and directed. 67 S&F in repairs plastic sheet covers for water closet, black, closed pattern with flat bottom with mild steel chromium plated or alluminised hinging device complete all as specified and directed. 68 S&FStainless steel grating with or without hole of size 150 mm complete all as specified and directed. 69 S&F in repair PVC waste pipe of 32mm dia complete all as specified and directed. 70 S&Fin repair SS shop dish of size 100mm complete all as specified and directed. 71 S&F in repair stainless steel sink 1.00mm thick for kitchen or laboratory, with plug, wast pipe, washers, including cantilever cast iron brackets, connecting union etc, overall size 495mmx420mm with bowl size 410mm x 330mm x 160mm including waste coupling, waste pipe complete all as specified and directed. 72 S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and waste coupling; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. 73 Supply and fix in repair 500 litres capacity triple layer (white), rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 25 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed. 74 Supply and fix in repair 1000 litres capacity tripple layer, rotational moulded, polythene water storage tank with cover (Cylindrical vertical with closed top),colour white ,hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 25 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed. 75 S& F in repairs sintex cover for over headtankof any capacity including all fittings complete all as specified and directed. 76 S&F in repair ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass ferrule and fixed 25mm dia complete all as specified and directed. 77 M & L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. 78 S& F in repairs 18/19 mm thick plywood (12 Nos of ply )grade BWR, typeBB fixed width screwsto timber frme work or ply wood for kitchen cupboard, shelves and cupboard as per manufacturer instructions complete all as specified and directed. 79 M & L 0.90mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturers instructions complete all as specified and directed. 80 S&F 75mmsize SS cup board hinges medium weight cold rolled complete all as specified and directed. 81 S&F in repairs Magnatic catcher and connected plate to shutters and frame as per Sample complete all as specified and directed. 82 S & F in repairs drawer handles cast iron or mold steel, projection drop (50mm to 65mm) on screwed plate complete all as specified and directed. 83 S& F in repairs Telescopic Channel of size 450mm (when closed), mild steel chromium plated , roller type, heavy duty etccomplete all as specified and directed. 84 Removing building materials (Cement concrete any description, bricks, stone slab and tiles,bricks dust or mud etc) to any distance beyond MD land the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and directed.Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations. 85 Note : (i)For item to be replaced under repair (day to day complaint) contactors trade man should report to complaint cell daily and take complaint from concren JE and after attending complaint he should give feedback and return the complaint slip to concern JE in the evening at 17.30 Hrs on same day. (ii) B/R complaint to be attend within 24 Hrs from the receiving of complaint, other wise panalty of Rs.500 per complaint per day will be imposed on contractor. In this regard decision of EIC and GE will full, final and binding to contractor. (iii) Being a maintenance contract site will be handover to contractor as per complaint received from user and as per site requirement. (iv) Rates for above shall be inclusive of rates quoted by contractor against BoQ/Sch A. No extra payment in this regards be made to the contractor.