Tender For annual repair To Rb Type-7, Sector-7 Chandigarh. (New Allotment)-Providing and fixing sunshade including sides consisting made out the frame M.S. Pipe 25 x 25 x 2mm and inner support of flat of size 25 x 6mm and fixing of 1.5mm thick polycarbonate sheet with help of self drilling screws. The rate also includes to chasing the brick work with the help of cutter machine, filling of silicone in chase, including the cost of two coats of paint over one coat of primer complete in all respect to the entire satisfaction of Engineer-in-charge. Providing and fixing 6mm thick polycarbonate multi wall sheet to be fixed on existing M.S. frame with Aluminum rivets complete in all respect to the entire satisfaction of Engineer-in-charge P/F 110mm internal dia PVC pipe as rain water pipe on walls of 6 kg. pressure with Bend, Elbow and Clamps complete in all respect to the entire satisfaction of Engineer -in-Charge 5 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets gates and similar works Providing and fixing 2-0 deep cupboard /cabinet consisting of 19mm thick commercial board and 6mm thick ply on back side, 4mm thick teak ply pasted on the exposed surface and making shelves in cabinet 0.8mm mica inside canbinet. The rate further includes the cost of lipping, piano hinges, cupboard lock, screws, nails, 2 nos fancy s.s handles, 2 nos, magnetic catchers, fevicol and painting two coats over one priming coat and preparation of surface on board and ply surface and spirit polishing on teak ply complete in position as per entire satisfaction of Engineer-in-charge. 1 Providing and laying Vitrified tiles in floor indifferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to 15:15622, of 1 approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry 3.3 kg/sqm including grouting the jointswith white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only Laying of tiles will be done with the notch trowel plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Double charge vitrified tile polished finish of size Size ofTile 600 x 600-mm Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement 3) coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Dismantling of ceramic tiles or vitrified and plaster to making the surface clean for refixing the glazed tiles including removing of malba complete in all respect and to the entire satisfaction of the Engineer in charge. Providing and laying 40mm thick factory made cement concrete rubber moulded interlocking paver block made with ratio 1:1:2 by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 30mm thick compacted bed of course sand, filling the joints with fine sand etc all complete as per direction of Engineer-in-charge. 1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level1:5:10 (1 cement: 5 coarse sand (zone III) derived from natural sources: 10 graded stone aggregate 40 mm nominal size derived from natural sources). Provding and installation of precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by the Engineer in charge) 0.50mm +-5% total coated thickness TCT) thick zinc coating 100gsm as per IS 277 in 240mpa steel grade, 5-4 microns epopxy primer on both sides of the sheet and polyester top coat of 15-18 microns. Sheet should have protective guard film of 25 micron minimum to avoid scratches while transportation and should be supplied in single length upto 12 metres or as desired by the Engineer in charge. The sheet shall be fixed by using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with whitel ead complete upto any pitch in horizontal/vertical or curved surface excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required complete in all repsects and to the entire satisfaction of the Engineer in charge. Providing and fixing of cupboard shutter consisting of 19mm thick commercial board with lipping all around and fixed with chowkhat frame with piano hinges and screws etc. and provide with Alum, handle (with base plate) and magnetic catcher. The board surface is to be painted with two coats of special quality synthetic enamel paint after primer coat and preparation of surface, complete frame is to be fixed with iron nails etc. complete in all respects and to the entire satisfaction ofthe Engineer in charge.Providing and laying water proofing coating using Single component acrylic polymer for cement based waterproof composite coating membrane. having three coats in which first Coat is primer coat containing 1 part waterproof composite coating membrane 2 part cement. Over primer coat the Geotextile fiber mesh of size 800 microns with total thickness of 900 to 1000 microns should be laid then further 2 coats 1 part waterproof composite coating membrane 1 part cement is laid in perpendicular direction to each other the joints/grooves may be filled using cement conrete of ratio 1:1:2 complete in all respect as per direction and to the entire satisfaction of Engineer-in-charge. 13 Wall painting with prernium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound)content less than 50 grams/litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. One coats 29 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: One or more coats on old work 1 Finishing walls with Acrylic Smooth exterior paint of required shade Old work (One or more coat applied @ 0.90 ltr/10 sqm). 91 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. Providing and applying filling with cement based putty (Birta, Jk or equivalent) to the required finish complete in all respect and to the entire satisfaction of Engineer-in-charge. 10 French spirit polishing: One or more coats on old work Providing and fixing heavy duty telescopic channel for drawers 18 to be fixed with necessary screws complete in all respects and to the entire satisfaction of the Engineer in charge. 50 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.