Tender For Special Repair Of P 29 Otm Accommodation (Lrw) At Nagtalao Under Ge Banar; 1 Demolition of Cement concrete in ground floors and pavings n.exc 15 cm thickness below or above ground level) and removing debris out of MOD land complete all as specified. 2 Demolition of Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work.if cement concrete is reinforcement cut as required to facilate demolition complete all as specified. 3 M&L for 50 mm thick cement concrete type B-1 1:2:4 (using 20mm graded crushed stone aggregate) to receive floor finishes etc complete all as specified. 4 M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified. 5 M&L of 20-25mm thick machine cut KOTA stone slab as in shelves (Single piece) fixed in walls machine cut, laid over cementand jointed with grey cement slurry with pigment to match the shade of the slab, incl rubbing and Mirrorpolishing complete all as specified. 6 Dismantling floor, hearth or wall tiling including cement mortar bedding, removing off the premises complete all as specified. 7 M&L for coloured glazed ceramic tiles 300mmx450mmx6mmthick as per IS 13712 Grade II(a) over and including 15mm thick rendering in CM (1:6) set and jointed in neat cement slurry and pointed with colour cement to match on vertical surfaces as in dado (colour and pattern as approved by GE) complete all as specified. 8 M&L forCeramic tiles 7 to 8 mm thick (white), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchand including 15mm thick screed bed in CM (1:6) complete all as specified. 9 Taking down cement plaster on stone masonry RCC surfaces, dado surfaces etc completeincl racking out joints, hacking for key scrubbing down with water complete all as specified. 10 M&L for 15mm thick rendering in CM 1:6 on stone masonry finished even and smooth without using extra cement complete all as specified. 11 M&L Rendering 10 mm thick in CM (1:4) on concrete surfaces on ceiling / facia /RCC Chhaja etc all as directed & finished even & smooth complete all as specified. 12 M&L for 15mm thick rendering in CM 1:4 on stone masonry finished even and smooth without using extra cement complete all as specified. 13 M/L for preparation of newly plastered/ unplastered surfaces of walls and applying two coats of oil bound distemper complete all as specified. 14 M&L for three coats of white wash including preparation of new surfaces on walls complete all as specified. 15 M&L for three coats of white wash including preparation of new surfaces as on ceilings complete all as specified. 16 Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified. 17 Taking down chowkat with shutters (without taking off shutter from frame) size area exc 1.5sqm but n.exc 4.0 sqm each complete all as specified. 18 S&F PVC door frame wooden finish of size 50mmx 47mm made out of 5mm plain color PVC sheet reinforced with MS square tube complete all as specified. 19 Taking down of window and ventilators complete all as specified. 20 S&F Anodised aluminium frame powder coated for doors, windows ventilators with one or more rebates including joining cleat for fixing etc complete all as specified. 21 M & L for 35mm thick flush shutters, solid core construction with block board core and veener face fixed on both side of door, coloured as approved by GE, including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified. 22 S & F 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified. 23 S&F power coated Anodised aluminium window and ventilator shutters(Thickness of powder coating not less than 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified. 24 S&F 5.5mm thick Sheet glass ordinary quality with solar control film of 25 micronreflective type sticked with glass as per manufacturer instuction and glazing with oil putty in square in exc 0.5sq.m in each pane complete all as specified. 25 S&F Anodised aluminium powder coated decogrill for doors, windows ventilators with one or more rebates including joining cleat for fixing etc complete all as specified. 26 S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified. 27 S&F galvanised mild steel wire cloth 0.56mmnominal dia of wire and average width ofaperature 1.18 mm complete all as specified. 28 M/L for two coat of synthetic enamel paint over a coat of pink primer on new wooden surface including preparation of surface, over 10Cm width or girth complete all as specified. 29 S&F factory made wooden finish PVC shutter 30 mm thick (style)consisting of frame made out of MS tube for top and bottom rails. MS frmae shall be covered with heat moulded plain color PVC channel having a PVC sheet for top rail of 20mm width width stuck in side with solvent cement for stiles and plain color PVC sheet for top rail lock rail on other side and as gap insert for top rail and bottom rail. Paneling of plain color PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and jointed together with slovent cement complete all as specified. 30 S &F of Stainless steel butt hinges medium weight, cold rolled of size 100 mm size complete all as specified. 31 S&F 150 mm long aluminium anodised tower bolt complete all as specified. 32 S&F 150mm long aluminium anodised handle extruded section complete all as specified. 33 S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified. 34 M/L for one coat of synthetic enamel painton old steel surface including preparation of surface, over 10Cm width or girth complete all as specified. 35 Taking up or down GI steelwater tubing 15 mm bore and connection complete all as specified. 36 Taking up or down GI tubing 20 mm bore and connection complete all as specified. 37 Supply & Fixing15mm bore GI Tubes, medium grade galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified. 38 Supply & Fixing20mm bore GI Tubes, medium grade galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified. 39 Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth complete all as specified. 40 S/F in repair of bib cock 15mm dia, cast copper alloy fancy type, screwed for iron pipe or for brass ferrule complete all as specified. 41 S&F in repairs angular stop valves cast copper alloy chromium plated(ISI marked) screwed down high pressure fancy type screwed both ends for 15mm bore of iron pipe or union complete all as specified. 42 S&F in repair25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixedin repair complete all as directed. 43 S&F 600mmx450mm bevelled edge mirror of selected quality glass 5.5 mm thick, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified. 44 M&L for 75mm outlet diameter UPVC nahani trap, with CP Mild steel grating (with or without hole) including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) using 20mm graded stone aggregate complete all as specified. 45 S&F tubular towel rail 20mm dia brass chromium plated `D type 60cm long with bracket and fixed complete all as specified. 46 M&L for 7.5cms thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:3 or cement mortar 1:4 complete all as specified. 47 S&F in repair of Vitreous China wash basin size 450 x 300mm with padestal, white, flat back, including 32 mm CP waste coupling, waste pipe, PVC Connection 300 mm long, brackets complete all as specified. 48 S&Fin repair vitreous china squatting Pan, Orissa Pattern of size 580X440mm white with integral foot rests and cast iron `P or `S trap front or back fixed in repairs Including connection to trap etc and provision of cement concrete bedding and making good to floor completely complete all as specified. 49 S&Fin repairVitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)and cast iron `P or `S trap front or back fixed in repairs Including connection to trap etc and provision of cement concrete bedding and making good to floor complete all as specified. 50 Dismentling of cast iron/pvc soil waste & vent pipes 100/110 mm dia incl all fittings etc complete all as specified. 51 Dismentling of cast iron/pvc soil waste & vent pipes 75 mm dia incl all fittings etc complete all as specified. 52 Supplying and laying of 75 mm dia UPVC pipes SWR& Plain UPVC SDR 11 fittings in trenches complete all as specified.(with all fitting) 53 Supplying and laying of 110 mm dia UPVC pipes SWR& Plain UPVC SDR 11 fittings in trenches complete all as specified. (with all fitting) 54 Supplying and laying of 75 mm dia UPVC pipes SWR fittings on walls / ceiling or laying in floors complete all as specified. (with all fitting) 55 Supplying and laying of 110 mm dia CPVC pipes SWR fittings on walls / ceiling or laying in floors complete all as specified. (with all fitting) 56 S&F 75 mm bore UPVC bends any radius with oval acess door complete all as specified. 57 S&F 110 mm bore UPVCbends any radius with oval acess doorcomplete all as specified. 58 Supply and fixing in repair PVC valve less symphonic action type flushing cistern 10 ltrs capacity low level with inlet, ball valve, float and handle Including bracket fixed complete all as specified. 59 S&F 32mm bore low or high density polyethylene waste pipes (LDPE) of pressure rating 6Kg/Sqm fixed complete to walls, ceiling or floors etc complete all as specified. 60 S&F in repair 15mm bore PVC connection (for Flushing cistern) 600mm long best qualitywith PTMT nuts complete all as specified. 61 M&L 40 mm thickPCC (1:2:4) type B1 using 20mm graded stone aggregate as in floor , hard standing flooring finished even and smooth without using extra cement complete all as specified. 62 M&L 50 mm thickPCC (1:3:6) type C1 using 20mm graded stone aggregate as in plinth protection finished complete including forming joints in 2 mtr interval and filled with bitumen mastic all as specified. 63 Taking down existing roof treatment in any postion and any thickness on RCC roof slab and debries to be disposed out of MOD land complete all as specified. 64 M&L for roof treatement in the following stages :-(a)Applying evenly a coat of bituminous primer conforming to IS-3384 @ 0.40 ltr per sqm over and including 10 mm thick cement mortoar (1:4) and surfaces finished even and smooth without using extra cement all as specified . (b)Second coat of blown type bitumen confirming to IS 702-1988 grade 85/25 @ 1.2 Kg/Sqm . (c) Third layer of APP modified polmeric membrane centre core of 20 micron HMHDPE outer folm 20 micron both sides thickness 1.5 mm having weight 2.25 Kg/Sqm. (d) Fourth coat of blown type bitumen confirming to IS 702-1988 grade 85/25 @ 1.2 Kg per Sqm.(e) 40mm thick PCC padding in cement concrete 1:2:4 (12.5 mm graded aggregate finishing even and smooth 65 Dismantling water tanks and removing to storeexc 500 ltr but n exc 1000 ltr complete all as specified. 66 S&F rotational moulded polyethylene water storage tank ISI Marked (cylindrical vertical with closed top) white, hoisted and fixed in position all as directed of capacity 1000 ltrs a Including 20mm bore brass ball valve high pressure with polythene float complete all as specified. 67 Supply only integral water proofing compound complete all as specified. 68 Taking down carefully cement conc /spalled out concrete fromRCC roof projections, ceiling ,sunsheds, beams, etc upto cover depth by chipping out lightly including necessary scafolding etc complete all as specified. 69 M&L for fixing MS 12 mm dia TMT bars by way of stitching ( welding ot tieing with existing reinf) incl drilling holes etc & securing ends in walls etc complete all as specified. 70 M&L for cleaning the existingreinf of slabs , chajjas etc& applying a coat of SIKA RUSTOFF 11 to remove the loose rust particles etc & throughly cleaning the surface complete all as specified. 71 M&L for applying a coat of bond coat made with cement slurry(1 part cement to 1.5 -2 parts water)mixed with admixtureLATEX POWERmixed @5 Kg per 50 kgof cement & applying to the conc surfaces @ 200 gm/sqm to obtain tack. 72 M&L for 15 -20 mm thick rendering in CM 1:1:2 using1 part of cement 1 part 2-3 mm screenings of stone agg & 2 parts coarse sandofover the bond coat applied surfaces with cement mixed with SIKA PLASTOCRETE SUPERadmixture @ 100 gm /50kg of cement & finishing the surface even & rough to receive final rendering coat complete all as specified. 73 M&L for 5 mm thick rendering in CM 1:3 & finishing the surface even & smooth w/o using extra cement complete all as specified. 74 M&L for 10-15 mm thick rendering in CM 1:3 over the bond coat applied surfaces with cement mixed with SIKA PLASTOCRETE SUPERadmixture @ 100 gm /50kg of cement & finishing the surface even & smooth complete all as specified. 75 S&F in repair stainless steel Soap Dish complete 76 S&F as in repairs stainless steel plate rack of size 30x24x10 size as per trade pattern fabricated with 0.50mm thick stainless steel sheet suitable for stacking 15 plates with hooks /fittings complete all as specified. 77 Excavating in trenches, n exc 1.5mwideandnexc1.5min depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc10sqmonplanandnexc 1.5 m in depth and getting outin soft soil complete all as specified. 78 Demolition and breaking up150 mm drain pipes (Salt glazed ware, AC or reinforcement concrete) set in cement mortar complete all as specified. 79 S&F 150mm Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified. 80 M&L for cement concret (1:3:6) type C-2, using 40mm graded stone aggregate bed to drain pipe 150 mm dia including packing under and hunching against the pipe after they are laid including necessary formwork complete all as specified. 81 Returning, filing in including, lelveling,watering and well ramming in layers not exc 25cm thick each complete all as specified. 82 Removing excavated material to a distance not exc 50m depositing where directed at a level not exc 1.5m above the starting point complete all as specified. 83 PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified. 84 M&L for Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel complete all as specified. 85 Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified. 86 S&F Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening whereverrequired complete.Office laid over sand filling layer & spreading fine sand over the tiles to fill in the joints & cleaning the same after filling of joints complete all as specified. 87 Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified. 88 M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed complete all as specified. 89 S &F in repair Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified. 90 Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, sockets, lamp holder and conduit etc. removing materials to store fortaking credit and making good disturbed surfaces of walls, floors, etc complete all as specified.Note:- The damaged surfaces to be made good with plastering& applying colour wash in required coats tomatching with existing surfaces as directed by Engineer-in-charge. Cost of the same deem to be included in quoted rates and nothing extra on this account admissible. 91 M&L for point wiring with two single core 1.5 Sq.mm size multistranded FRLS copper conductor PVC insulated cables and one single core 1.5 Sq.mm size green colour PVC insulated,multistranded copper conductor PVC cable as earth continuity conductor,1100 volts grade, complete drawn in and including rigid PVC CONDUIT and conduit accessories,confirming to IS specifications,concealed in wall fixing on ceiling /trusses with suitable clamps , screws etc, including 1.22 mm thick MS terminal boxes with 3 mm thick plastic laminated sheet top cover fixed with cadmium plated iron screws for mounting switches, sockets, fan regulators etc.,including connecting up and testing , all as specified and as directed for :-(a) One light point controlled by one switch. 92 All item as per Ser No 91.00 above but one fan/ exhaust fan point controlled by one switch. 93 All item as per Ser No 91.00 above but one switch socket out let point 5 Amps on independent board complete all as specified. 94 All item as per Ser No 91.00 above but one switch socket out let point 5 Amps on same board. 95 Ditto all as per item No 91.00 herein before but with 4 sqmm cable for one 3 pin 15 Amp switch socket outlet and using 4 sqmm PVC single core copper conductor cable multistranded as earth wire complete all as specified. 96 Supply and fixing switch piano flush type 5 Amp single pole, one way complete all as specified. 97 Supply and fixing for ceiling rose surface bakelite 65 x 50 mm three terminal complete all as specified. 98 Supply and fixing socket outlet 5 pin 5 Amps, flush type complete all as specified. 99 Supply and fixing Socket outlet combination 2 in 1 3 pin 6 and 16 amp flush type universal complete all as specified. 100 Supply and fixing Socket outlet combination 2 in 1 3 pin 6flush type universalcomplete all as specified. 101 Supply and fixing lamp holder PVC/polycarbonate type with cord grip cap suitable for pendant fitting complete all as specified. 102 S&F powder coated sheet metal enclosures MCCB VTPN DB, double door, tripple pole and neutral, 4 way 415 volts fitted with insulated vertical phase bus bar/neutral bar OF CAPACITY 100 Awith shround earth bar cement spill proctector interconnecting wire set cable tiesblanking plates and circuit indentificationlables etc all as per IS-8623-1 IK-09 and making good disturbed surfaces of walls including plaster cutting of wall etccomplete all as specified. 103 Supply and fixing MCCB TPN 63 Amps 415 volts. 10kAAdjustableoverload setting l &fixed magnetic settingcomplete all as specified. 104 Supply and fixing powder coated sheet metal enclosuresDB, double door, single pole and neutral 8 way 240 Volt fitted with bus bar, DIN channel, neutral link and incoming contact and making good disturbed surfaces of walls including plaster cutting of wall etccomplete all as specified. 105 Supply and fixing MCB SPN 40 Amps240 volts complete all as specified. 106 Supply and fixing MCB SPN 6-32 Amps240 volts complete all as specified. 107 Supply and fixing MCB SP 6 Amps to 32 Amps 230 Volt complete all as specified. 108 S&F surface mounting batten tube light fitting, integrated polycarbonate LED channel with white acrylic cover complete suitable for and including lamp LED 1x20 Watt,(4 feet) fixed properly on wall surface and connecting complete from ceilling rose to fitting by three core copper conductor cable of overall sheathed size 2.5 Sqmm which shall be passed through PVC flexible conduit complete all as specified. 109 Taking down old fitting and S&Fbuilding security light LED fitting 35 watt 230V AC outdoor type with high pressure die cast aluminum housing and heat resistant , epoxy powder coated dark graphite grey colour finish and prismatic polycarbonate cover with individual LED lences suitable for including lamp LED 35 watt, fixed / connect properly at directed location on building with IP 65/66 protection complete all as specified. 110 Taking down old bracket andSupply and fixing bracket for street light fittings of any size made out of GI pipe medium grade 32 mm dia 1.25 mtr length bend to required size and shape including provision of clamps and fittings in position and two coat of aluminum paint over a coat of red oxide primer all as specified and directed including taking down old bracket complete all as specified. 111 M & L for Sub main wiring complete with three single core 4.0 sqmm,1100 volts grade, PVC insulated, strandedcopper conductor FRLScable with continuous copperearth conductor of 4.0 sqmmin and including PVC casing caping and accessories complete all as specified. (Note:- (i) Making good of disturbed surfaces will be done by contractor without any claims. (ii) 3 runs of 4.00 Sqmm conductor and one run of PVC casing caping shall be measured as one unit length.) complete all as specified. 112 M & L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sq. mm 4.0core complete all as specified. 113 Material and labour for 40mm dia galvanized iron tube light grade for cable protection, supporting to poles, plinth protections, road crossing, trenches, footpath etc, complete all as specified including clamps, nut bolt and washers complete all as specified. 114 Taking down Oldfan deposit to AGE E/M Storeand S&FCeiling fan 1200mm sweepsingle phase 230 volts AC, min air delivery 210 CFM with service valve 6.00 BEE 5 star rating with brushless direct current motor (BLDC) withblade ,down roads electronic regulator andcomplete accessories complete fixed properly on wall surface with the provisioning of suitable sizes of rag bolts, nuts, washer and to connect by using cable PVC insulated copper stranded conductor of size 2.5 Sqmm 3 core and overall PVC sheathed which shall be passed through PVC flexible conduit of length not exceeding 0.50 mtr complete all as specified. 115 Taking down Old Exhust fan deposit to AGE E/M Store and S&F for Steel body Exhaust Fan 300 mm sweep, single phase 230 volts AC, 900 RPMfour blade with louver shutters complete fixed properly on wall surface with the provisioning of suitable sizes of rag bolts, nuts, washer and to connect by using cable PVC insulated copper stranded conductor of size 2.5 Sqmm 3 core and overall PVC sheathed which shall be passed through PVC flexible conduit of length not exceeding 0.50 mtr complete all as specified. 116 M & L for building earthing complete in repair with galvanised steel earth plate electrode 60 x 60x 6mm burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edged of the plate not less than 1.5 mtr below normal ground level,connected to galavanised iron earth lead by means ofbolt, nut, check nut and washer of galavanised iron wire 4mmas earthing lead as shown in Electrical Plate No 3 of SSR Part I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work inhard/dence soil, earth pit in PCC 1:3:6 typeC1 using 20mm stone aggreate, funnel, 20 mm dia GI medium grade water pipe, 15mm dia GI light grade earth lead protection pipe, CI frame and cover, wire, copper lugs,wire mesh, charcoal or coke and common salt in alterative layer all around the earth electrode compacted thickness 15 cm including excavation and earth work pit cover including disposal of surplus soil to a distance not excessding 50m, complete testing on completion all complete as shown in electrical plate No 3 of SSR Part I 2009 complete all as specified.
