|
| 1 | Dismantling structural steel work in cluding doors, gates but excluding framed truss etc. complete all as specified and as directed. |
| 2 | Demolition of reinforced cement concreteof any description and in anypositioncomplete all as specified and as directed. |
| 3 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing debries out side defence areacomplete all as specified and as directed. |
| 4 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation,depth and getting out in any type of soilcomplete all as specified and as directed. |
| 5 | Excavation in post holes or similar holes(each n exc 0.5 cum), getting out, returning, filling in and ramming earth or broken rubble wixed with earth around, in layers not exceeding 25 cm and getting out in any type of soilcomplete all as specified and as directed. |
| 6 | M&L for precast cement concrete block masonry with solid block, Type C1 1:3:6 (using 20mm graded stone aggregate) exc 10 cm in width and setting in cement mortar 1:6complete all as specified and as directed. |
| 7 | M&L 15 mm thick rendering CM 1:4over precast cement concrete block masonry surfaces and finished even and smooth without using extra cementcomplete all as specified and as directed. |
| 8 | M & L for preparation of newly plastered surfaces exc 10cm width or girth, of any description and applying two coats of cement based paint over a coat of primer, complete all as specified and as directed. |
| 9 | M & L for prepration of new plastered surface and applying two coats of white wash on wallscomplete all as specified and as directed. |
| 10 | M&L for cement concrete type D2 1:4:8 (40mm graded stone aggregate) in foundation, filling and mass concretecomplete all as specified and as directed. |
| 11 | Material & labour PCC (1:3:6) type C-1 using 20mm graded stone aggregates as in foundation fitting & mass concretecomplete all as specified and as directed. |
| 12 | M&L for RCC Nominal mix type B-1 1:2:4 (20 mm graded crushed stone agg) as in Columns, pillars, piers, postscomplete all as specified and as directed. |
| 13 | Formwork to sides of pillars, posts, struts, piers, columns etccomplete all as specified and as directed. |
| 14 | M&L Mild steel TMT bars 6 to 8mm dia ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, (as in stirrups) hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to Fe-310-O or Fe-410-Ocomplete all as specified and as directed. |
| 15 | M&L Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clipscomplete all as specified and as directed. |
| 16 | M&L for 20mm thick Granite (of any type) tiles machine cut, laid over 20mm thick cement screed in 1:3 and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishingcomplete all as specified and as directed. |
| 17 | S&F Framed work as in doors or gates of angle, tube and other section with gusset plates, rails races, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete to similar work conferming to Fe 290 Gde 165complete all as specified and as directed. |
| 18 | S&F mild steel works as in posts, struts, fire points structure and other section including cutting tops to shape as directed, drilling holes, notching for wire etc and flat iron fillets forwork Confirming to Fe-290 (Gde E-165) etc,complete all as specified and as directed. |
| 19 | S&F Plates (plain or chequered) channels, square cut or notched as in gate and welded complete conferming to Fe 290 Gde 165complete all as specified and as directed. |
| 20 | S&F 1.60 mm thick MS plain black sheet in steel gate and similar work, cut to size, holes punched, including riviting, welded seam and bending etccomplete all as specified and as directed. |
| 21 | S&F 0.63 mm GI Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 and L-type or J-type or cranked hook bolts in lieu of screw in roofs, walls etccomplete all as specified and as directed. |
| 22 | M&L Synthetic two coats enamel paint on new steel Surfaces of any description n exc 10cm width or girth over a coat of red oxide primer including preparation of surfaces when unconnected with other painting or when painted in different tintcomplete all as specified and as directed. |
| 23 | Returning, filling including spreading, watering and well ramming in layers n.exc 25 cm in any type of soil complete all as specified and as directed. |
| 24 | Removing excavated materialto a distance exc 250 mtr but not exc 500 mtr depositing where directedcomplete all as specified and as directed. |
